Search Documents

By Koichi Nishimura

Japan's coal reserves are estimated at 8,583 million tons (according to the materials on X World Energy Conference,. 1976). Japan is a long island country in the shape of an elongated cashew nut whose top is pointing to the north and its lower tip is pointing to the west. And her major coal fields are located in the two extreme far parts of Hokkaido in the north and Kyushu in the south. On the other hand, Japan's major industrial center are located in the central part of the country far from either coal-producing areas. This fact places coal a great geographical disadvantage in comparison with petroleum whose refining bases are concentrated on the coastal regions virtually next to major industrial centers.

Jan 1, 1982

In early 1970, General Mills Chemicals, Inc. announced the availability of en improved liquid ion exchange reagent, LIX® 64N, for the recovery of copper from various solutions, such as dump leach liquors. LIX 64N has been shown to be a considerable advance over LIX 64, and is presently in use in three commercial plants. Results have been very gratifying. For example, one of the plants was designed for operational production of 40,000 pounds copper per day, and in fact reached this output within the third week following startup of the plant. In addition to the operating plants, another is scheduled to come on stream this month with L D( 64N being used to extract and recover both copper and nickel. The chemical properties and operating characteristics of this reagent have been fully described in a previous paper. 1 LIX 64N is quite an effective and selective extractint for copper, even with copper contents as high as 15 g/l, but the reagent is somewhat limited in pH range, and loses some of its extraction efficiency as the pH drops below 0.8. Liquors derived from vat leaching, electrolytic tankhouae bleed streams, or some of the new leach schemes derived to solubilize copper from sulfide concentrates are examples of the liquors that present major problems when treated via liquid ion exchange. LIX 64N could extract some of the copper from such streams, but recovery was limited to about 75 percent. Also, in some parts of the world there are streams which are relatively low in copper (-5 g/l) but which are very high in acid (25-50 g/1 H2SO4). Again, LIX 64N can attain only about 75 percent recovery from such streams. For effective treatment, these streams require a reagent which will maintain the excellent selectivity of LIX 64N, and will

Jan 1, 1971

By K. Oraee

Mining of copper ore and the related industries play an important role in Iran?s economy. Copper ore production in Iran accounts for 75% of the total production in the Middle East. All activities related to copper, that is, exploration, production, refinement etc are owned and managed by state owned companies. Decisions have been made to privatize all these activities. To assess the success of this privatization process, different components of the industry must be subject to economic analysis. In this paper, the cost estimation of all operations has been carried out. The total potential and attainable revenues have also been estimated using historical data available from the industry. Risk is a major factor in all mining activities and the copper industry of Iran has been subject to risk factors arising from many internal and external variables. These variables have been recognized and their effects evaluated. The effect of risk on the economic feasibility of the operations in the industry has also been analyzed.

Jan 1, 2011

By O. F. Brown

Excavation and loading are primary operations in the surface mine production chain, constituting a significant component of production costs. This makes excavation and loading important cost centers that need to be improved to lower production costs. Optimizing the design and use of excavators will improve energy efficiency in earthmoving operations, and this requires a thorough understanding of the soil-tool interaction process. Modeling the interaction process accurately is the key to this optimization. Experimental and analytical methods have provided limited information on the behavior of soils during excavation. Finite element (Fe) analysis of soil-cutting blade interaction produces some advantages over experimental and analytical methods. However, the soil constitutive equations used in most of the available Fe analyses fail to adequately model the plastic behavior of the soil. This work uses Fe modeling to study the behavior of formation-cutting blade interactions in dozer excavation. The formation is modeled as a nonlinear elastoplastic material using the modified cam-clay (mCC) model. The model accounts for soil-tool interface friction, and progressive and continuous cutting at the blade tip. The results provide soil forces, a progressive developed failure zone and soil displacement fields. The sensitivity analysis of changes in blade angle on cutting force shows that the cutting force increases with increasing blade angle. The cutting depth of the blade had a similar effect on blade cutting force. Increasing the depth of cut increases the required cutting force. Increasing the coefficient of friction at the soil blade interface increases the blade cutting force. Reducing the coefficient of friction at the soil blade interface from 0.3 to 0.05 reduces the cutting force by 22.3%. The percentage represents the maximum potential savings in blade cutting force. This research initiative advances the frontiers of soil-tool interactions during excavations to expand the limited knowledge in this critical area.

Jan 1, 2012

By P. K. Kaiser, M. Cai

When designing an efficient and effective support system for burst-prone ground, it necessary to select the most appropriate, i.e., the ‘right’ support components, including areal and reinforcement components. For this paper, it is assumed that the areal support is not the weakest link and the support performance is controlled by the rock reinforcement and holding components (bolts). We discuss the loading modes of rockbolts under static and dynamic loadings and analyze published data from laboratory and field tests. The mechanisms of energy absorption of dynamic rockbolts are presented and rockbolts are categorized based on factors such as energy absorption capacity, energy absorption rate, direct and indirect energy absorption capacities, rock mass bulking or displacement control, and shearing resistance capacity. Guidelines for selecting the ‘right’ rockbolts to build an effective rock support system for burst-prone ground are provided.

Apr 26, 2022

By Q. Wu

Neural network methodology is used to predict mean particle size resulting from rock blast fragmentation. A blast data base developed in a previous study is used in the current study. A part of this blast data was used to train a single-hidden layer back propagation neural network model for each of the similarity groups obtained in the same previous study. Levenberg-Marquardt algorithm provided the most stable and efficient training out of the four algorithms evaluated. An extensive analysis was performed using a part of the blast data to estimate the optimum number of units for the hidden layer for each similarity group. The remaining blast data are used to validate the trained neural network models. Capability of the developed neural network models is determined by comparing predictions with measured values and predictions based on one of the most applied fragmentation prediction models appearing in the blasting literature. Prediction capability of the neural network models was found to be strong and better than the existing most applied model. Diversity of the blasts data used is one of the most important aspects of the developed models. The developed neural network models are suitable for practical use at mines.

Jan 1, 2011

By Shemek Oginski, MARK C. JOHNSON

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2015

By SME SME

NORTH AMERICAN TUNNELING 2024 PROCEEDINGS

Jun 23, 2024

By I. Moreno-Ventas, G. Ríos, J. C. Fernández-Caliani, M. Bacedoni

"This paper delves into the constraints on the nature, origin and thermal evolution of the accretions formed in the uptake shaft of the flash smelting furnace operated by Atlantic Copper in Huelva, Spain, outlining recommended practices for preventing accretion buildup. The accretions were investigated using quantitative electron probe microanalysis, X-ray diffraction and digital imaging techniques, and the experimental data on mineral composition, crystal chemistry and textural relationships were interpreted in terms of thermodynamic phase equilibrium in the SiO2-Fe-O-S system. The results suggest that two distinct types of accretions were formed by the fractional crystallization of two coexisting immiscible melts, under changing conditions of oxygen partial pressure (pO2). The type I accretion of magnetite + delafossite ± cuprite ± tridymite ± metallic copper crystallized from a fractionating copper-rich melt at pO2 above about 10-5 atm, while the type II accretion of magnetite + fayalite + metallic copper + chalcocite derived from a melt with lower copper concentration when pO2 levels dropped below that critical level. Phase compositions and textures were consistent with a cooling history of both compositionally contrasting liquids from about 1,250 °C, the liquidus temperature of magnetite, to eutectic or near-eutectic temperatures of around 1,100 °C. The maintenance of appropriate temperatures — above the liquidus temperature of magnetite — and oxygen partial pressure levels may be critical for the prevention of accretion buildup. IntroductionCopper flash smelting with oxygen-enriched air, an autothermal process developed half a century ago by Outotec (Espoo, Finland), formerly Outokumpu, currently accounts for about 50 percent of the world’s primary sulfide-based copper (Schlesinger et al., 2011). The partial reaction of copper sulfide concentrates produces two separate molten streams, copper-iron-sulfide matte and iron oxide-rich slag, and releases sulfur dioxide (SO2) gas. The matte is sent to converters to remove the remaining iron and sulfur, leaving blister copper with grade of about 99.5 percent copper (Cu), which is cast into anodes for electrolytic refining.The SO2-rich gas generated by the oxidation of sulfide feed particles contains a significant proportion of dust that is entrained in the process off-gas. The gas from smelting is transferred into a waste heat recovery boiler, where it is cleared of dust and cooled before it is converted into sulfuric acid. If the process is not operated properly, the dust-bearing gas may form accretions between the uptake shaft of the flash smelting furnace and the waste heat recovery boiler, causing severe problems in the gas handling system (Swinbourne, Simak and Yazawa, 2002; Miettinen, 2008; Stefanova et al., 2012). Removing the dust accretions usually requires a greal deal of time, effort and resources. Understanding the buildup of accretion may help in reducing the problems and optimizing the process"

Jan 1, 2017

By T. Sun, J. Kou, D. Tao

"The reduction behavior of low-grade lump hematite ore (100% 20-50 mm) has been evaluated by performing a series of coal-based direct reduction roasting tests followed by magnetic separation under different process conditions such as roasting time, temperature, reductant type and dosage, and grinding stage. To investigate mineralogical transformation and reduction characteristics of lump hematite ore, roasted ores and magnetic concentrates were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS) and polarizing microscope. The results have shown that a magnetic concentrate with a total iron (TFe) grade of 90.7% was produced at an iron recovery of 83.9% when lump hematite ore was reduced at 1,200° C for five hours using 35% lignite as a reductant followed by two stages of grinding, for 20 min and 30 min each, and low-intensity magnetic separation. The degree of reduction is closely related to the change in the internal structure of the roasted ore. Lignite with a higher fixed carbon content and lower ash generated roasted ore with a more highly porous structure, which provides better permeability of reducing gas. Magnetite, fayalite and wustite were the dominant intermediates of coal-based direct reduction of lump hematite ore. Parts of wustite reacted with SiO2 or Al2O3 in gangue and generated fayalite or hercynite. FeO in fayalite was replaced by CaO to produce wustite, which was finally reduced to metallic iron. However, Fe in fayalite and hercynite produced with low contents of CaO cannot be reduced into metallic iron. Introduction Low-grade hematite ore, characterized by low Fe content and high SiO2 content, cannot be treated by traditional mineral processing methods due to its nonmagnetic property and fine liberation size. The direct reduction (DR) roasting process has been studied and proven satisfactory in treating difficult-toprocess ores, such as low-grade nickel laterite oxide ore (O’Connor et al., 2006; Cao et al., 2010; Guo et al., 2011), high phosphorus oolitic hematite ore (Li et al., 2012; Yu et al., 2013), low-grade hematite ore (Wei et al., 2013;) and iron ore tailings (Li et al., 2010), which greatly expand the resources of usable iron ores (Srivastava and Kawatra, 2009). Therefore, the use of a DR process to treat low-grade hematite ore to produce direct reduced iron (DRI) is of great interest to many researchers of mineral processing and metallurgy (Weissberger et al., 1986)."

Jan 1, 2015

By Matthew Preedy, Brett Campbell, Jim Rush, Alan Howard, Derek Penrice

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2018

By S. M. Hossaini, M. Ataei, H. Moosavi

The abstract highlights the importance of pillar stability in underground coal mines and the influence of rock mass strength and joint orientation on pillar behavior. The study employs numerical modeling using the distinct element code (UDEC) to investigate the impact of these factors on pillar stability. The research considers different joint orientations and varying rock mass strengths, analyzing parameters like stress distribution, displacement, and failure patterns. The findings reveal that both joint orientation and rock mass strength significantly affect pillar stability, with specific combinations leading to reduced safety factors and increased deformation. The study concludes by emphasizing the importance of considering these factors in pillar design for safe and efficient mining operations.

Apr 4, 2022

By P. K. Kankar, Manoj Khandelwal, Ramesht Shukla

One of the utmost severe mining catastrophes in underground hard rock mines is rock burst phenomena. It can lead to damage to mine openings and equipment as well as trigger accidents or even threat to life as well. Due to this, a number of researchers are forced to study some easy-to-use alternative methods to predict the rock burst occurrence. Nevertheless, due to the extremely multifaceted relation between mechanical, geological and geometric factors of the mines, the conventional prediction methods are not able to produce accurate results. With the expansion of machine learning methods, a revolution in the rock burst occurrence has become imaginable. In present study, three machine learning methods, namely XGBoost, decision tree and support vector machine, are utilized to predict the occurrence of rock burst in various underground projects. A total of 134 rock burst events were gathered together from various published literatures comprising maximum tangential stress (MTS), elastic energy index (EEI), uniaxial compressive strength and uniaxial tensile stress (UTS) that have been used to develop various machine learning models. The performance of machine learning methods is evaluated based on the accuracy, sensitivity and specificity of the rock burst prediction.

Mar 17, 2021

The knowledge of aggregate size under various chemical and hydrodynamic conditions is very important for selective agglomeration, flotation and water clarification processes. Traditionally, aggregate size measurements are conducted using an ex-situ technique or in a diluted suspension. In either case, the measurement occurs in an environment that does not resemble the actual conditions under which the aggregates are formed. In this study, an on-line scanning laser microscope has been used to study the coagula size of micronized coal suspensions as a function of pH, solids concentration and agitation intensity. A maximum aggregate size of 310 µ m was obtained under relatively quiescent conditions and at pH values near the iso-electric point (iep) of the coal. The aggregate size results compare well with the coagulation efficiency measurements obtained under the same pH conditions.

Jan 1, 1994

By K. Oraee

Zarshuran gold deposit, with the total reserves of some 12.5 million tons of 4.18 g/ton ore, is considered to be an important gold mining project in the area. In this paper the feasibility studies of the whole project is carried out on the basis of several economic variables. Given that mining data are often of uncertain nature, these economic variables have therefore been estimated under the conditions of uncertainty. The resultant Net Present Value is hence also obtained under the same conditions. For this purpose, a model is first devised with the help of Excel and COMFAR software. The model is then developed that considers different scenarios which would result in different expected values for the economic variables. It is concluded that the NPV of the project is most sensitive to gold and silver price and that other variables such as discount rate, operating and capital cost all affect the feasibility of the project with lower degree of severity. Finally, risk analysis is also carried out using Mont Carlo technique, in order to estimate the most probable value of NPV. The average NPV calculated in this way is US$ 49.7 Million, whilst without due consideration of risk, this would be US$ 36.6 Million. The techniques used, together with the procedures adopted in this paper, can be used in feasibility studies of all mining projects. Such decision would result in more accurate Net Present Values than expected from other frequently used methods.

Jan 1, 2011

By J. Kallioinen

Theoretical considerations, experimental results and plant experience have lead to a new design concept called the unit reactor approach. It has been successfully implemented to the largest flotation cell on the market, the 4000 cu ft OK TankCell. The work has also lead to a new operating idea called size specific flotation. The paper discusses these concepts in the view of full scale field experiments. In large scale porphyry copper flotation experiments conducted in Chile the new large TankCell with its new low energy input Free Flow mechanism out-performed the more conventional designs. The recovery was substantially better, especially in the coarse fractions. In some experiments the difference in total recovery was up to 10%-units and the savings in total energy consumption at the same time over 40%.

Jan 1, 1995

By E. Lee Bray

"Editor’s note: The editors thank those who make this annual issue possible. A special thank you goes out to the Industrial Minerals Annual Review editor, to the Industrial Minerals & Aggregates Division Technical Committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech Geo, is the industrial minerals annual review editor. Edgar Blanco, member SME, of Freeport- McMoRan, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• NickTushar Gupta and Sallie Gaillard, of the USGS, members SME, agricultural materials.• Abhishek Choudhuryand Xihui Yin, members SME, of Montana Tech and Kemira, repectively, ceramic and refractory materials.• Bobbi Strange and Riddhika Jain, members SME, of Outotec, Martin Marietta and Outotec, respectively, chemical raw materials.• Snehamoy Chatterjee, Alyssa Kendir and Alind Chandra, members SME, of BMT, Universityof Kentucky and Michigan Tech, respectively,construction aggregates.• Subham Verma, Gauran Soni and Freddy Sime, members SME, fillers and pigments.• Kaiwu Huang, Thomas Hilderbrand and Ricardo Santander members SME, of Virginia Tech, Thiele Kaolin and Carbo Ceramics, respectively, sorbents, filters and process aids.• Rhaghay Dubey and William Rapier, members SME, of Outotec and a consultant, respectively, specialty minerals.On behalf of ME readers, the editors thankTwo U.S. alumina refineries produced an estimated 1.5 Mt (1.65 million st) of alumina from imported bauxite in the United States in 2018. The 500-kt/a (550,000-stpy) refinery in Burnside, LA, owned by Almatis Inc. produced specialty alumina used in the abrasives, ceramics, chemical and refractory industries. The 1.2-Mt/a (1.32 million-stpy) refinery in Gramercy, LA, owned by Noranda Alumina LLC produced alumina mostly for use in aluminum smelters but also produced specialty alumina. An upgrade project at the Gramercy refinery to convert 200 kt/a (220,000 stpy) of capacity to produce more profitable specialty alumina was completed in the first half of 2018, and another project to increase capacity was started but a completion schedule was not available. The amount of new capacity was not disclosed, but it would be used to produce nonmetallurgical grade alumina. The 2.3-Mt/a (2.5 million-stpy) refinery in Point Comfort, TX, which was temporarily shut down in March 2016, remained closed throughout the year."

Jul 1, 2019

By Edward P. Larsen

At our annual meeting in St, Louis, Mo. in February 1961, we presented a comprehensive paper (No. 61-B-22) on the subject of "Blending and Handling of Materials for Agglomeration". In that paper you will find a discussion on the difference between "blending" and "mixing". With regard to "blending" we brought out the facts of its usefulness for the preparation o materials in an agglomerated mass to attain controlled chemical and physical uniformity. "Mixing" was discredited as not being useful for the attainment of uniformity of any kind.

Jan 1, 1962

By Richard B. Stein

Section 25 has been assembled to give the geological, mining, or metallurgical engineer an overview of some of the important downstream operations that typically follow mining activities. This subject is obviously too broad and complex to be covered in detail within this Handbook. However, the engineer will be interested to learn about the basic fundamentals, and especially how they might affect the economics of the total project from prospecting and mining through to metals recovery and marketing. In this way, it is hoped that the engineer will have a better overall appreciation for the technical and commercial prospects of a mining and metal-producing project.

Jan 1, 2008

By X. Meng

A kinetic model for batch leaching of various metals with different lixiviants has been developed. Overall material balances for reactants and products at the solid/liquid interface were formulated with various types of heterogeneous reactions in place at the interface. The solutions to these mass balances have been identified analytically as well as numerically using a Runge-Kutta method. Applications of these numerical solutions to various leaching systems using the rotating disc or powders have been discussed. Examples of the metal dissolution systems considered in this study include cobalt, nickel, copper and gold in acid, cyanide or ammoniacal solutions.

Jan 1, 1994