Search Documents

By Phil W. Welch

At first glance, the similarity between the fine grinding of cement clinker and coarse grinding done in other mineral processing industries may seem remote. However, it is interesting to note that the mill discharge fineness of cement clinker is only 70 to 90% passing 100 mesh and quite comparable to other mineral processing grinds. There is however, a greater dependence of the mill on the air separator in the finish grinding of cement clinker than in other mineral processing industries which explains why a technique to guage the balance between a mill and separator first began in the cement industry. (1) More recently an adaptation of this technique has shown its application to the processing of phosphate rock and is the central topic of this paper. First, an explanation of work done with fine grinding cement circuits seems appropriate together with a few general comments regarding cement. When unground or partially ground cement clinker enters a finish grinding mill, it is subjected to mechanical forces of impact and attrition which gradually reduce it to a range of sizes characteristic of finish cement. That is, a range of approximately 1 to 125 microns. The large proportion of superfine particles relative to the coarse and intermediate size particles is typical of portland cement particle size distribution. It accounts for the workability characteristics of plastic concrete and the early strength development of concrete which is so necessary to its successful use as a construction material. For this reason It is quite evident from quality control tests when a shortage of superfines exists.

Jan 1, 1975

By B. Goertz

Since the turn of the century the mining industry in the United States has had a number of serious mine explosions, fires and ground fall disasters that have led to a major re-evaluation of mine communication and rescue practices. One of the hindrances of current underground communication technologies is the potential of lost or cut connections when a serious accident, such as an explosion, fire, inundation or major ground fall, takes place. The Mine Improvement and New Emergency Response Act of 2006 (MINER Act)1 mandated that each underground coal mine in the U.S. must provide for two-way wireless, post-accident communications between underground and surface personnel as well as electronic tracking of underground workers One area that has gained renewed attention in the mining sector is Through-The-Earth (TTE) communication. TTE technology has a major advantage in that transceiver devices can be carried by miners and set up quickly during an emergency, since they require no wire connection to the surface. TTE technology uses ultra-low frequency (1 to 4 kHz) electromagnetic waves, requiring relatively large wire loop antennas and highly sensitive receivers. The signal bandwidth is narrow and the permissible antenna currents in coal mines are restricted, which has led to limited usability of TTE technology in the past, as evidenced in research studies conducted by the U.S. Bureau of Mines in the 1970s. Yenchek (2012)2 pointed out that recent advances in receiver and signal processing technology have enabled voice and text communication capabilities and much improved sensitivity that offers new possibilities for TTE communication in mining applications. One company that has been developing such technology is Vital Alert Communication Inc. Vital Alert has been providing TTE communications since 2003 with a growing focus on emergency response and portable systems. The company?s Canary® Go System is one such product that looks to provide reliable communication capabilities in a portable, user friendly unit that can be utilized both for normal operation and mine rescue scenarios. Researchers at the Colorado School of Mines (CSM) have tested the Canary Go TTE communications system in the CSM Edgar Experimental Mine to determine signal propagation distances, signal quality and aspects of practical application.

Feb 23, 2014

By C. Sampaio, C. Petter, M. Veras

"INTRODUCTION Use of sensor technology applied to the gravimetric beneficiation is intended for the selective preconcentration or separation of various minerals. Sensor Based Sorting (SBS) uses sensors to identify the particles and separate them by a mechanical process (flap) or pneumatic ejection valves (Wotruba et al. 2014). The principle of the SBS technology to separate mineral particles consists of three phases which cover feed,detection and separation. (killmann, 2009 Apud nienhaus et al. 2014). The applicability of the technique in an early stage of beneficiation enables free particles and poor grade to be a part of the process. The mass of tailings to be processed can be removed at the initial stage to save energy, water and equipment maintenance (Wotruba et al. 2014). Lindner (2010) suggested that the use of SBS technology would only will be possible if there exsists an electromagnetic interaction in all the wave spectra interacting with the solid ore. The interaction of electromagnetic waves depends directly on the characteristics of the material. The material receives a spectrum of electromagnetic waves by irradiation and this results in a reduced wavelength with differing types radiation such as fluorescence, reflection, remission, absorption, transmission and transmission. The frequency of the wave spectrum varies between 1000 and 1020Hz, illustrated by the data in Figure 1, which shows that each type of sensor emits a wavelength inversely proportional to the frequency ranging from 10-11pm to 104km, and the frequency that varies between EHz 103 and 1020kHz. The difference between the electromagnetic spectrum variations can only be visible to the human eye at wavelengths with intervals between 380nm and 780nm (Wotruba et al. 2014). One of the main advantages of operating with imaging sensors is the versatility of the images which can take on zero, one, two or three dimensions shown below as a point, a line, an area or a spatial image, as illustrated in Figure 2. According to Schubert (1988), to separate a mineral particle it is necessary to follow the characteristics of mineralogy, physics and chemistry with or without use of water. The use of new technologies can help reduce operating costs and improve utilization of mineral resources."

Jan 1, 2016

By Kenneth S. Johnson

Large reserves of high-purity Permian gypsum crop out and are at shallow depth in three regions of western Oklahoma, Gypsum beds in the Blaine Formation are 10 to 30 feet thick and are generally 95 to 99 percent pure, whereas the massive Cloud Chief Gypsum is 20 to 100 feet thick and is 92 to 97 percent pure. Reserves are estimated at 48 billion short tons. Eight companies in the State currently mine about 1 million tons of gypsum each year for wall- board, for plaster, as a retarder in portland cement, and as a soil conditioner. Future uses, under more favorable market conditions, may be in the chemical industries, largely because of gypsum's potential as a source of sulfur. Three thick sequences of Permian rock salt underlie most of western Oklahoma at depths of 30 to 3,000 feet. Individual salt beds 5 to 30 feet thick are interbedded with thinner layers of shale and anhydrite. Five large salt plains, fed by natural springs of saturated brine constitute additional resources of salt. Reserves, estimated at 20 trillion short tons, are virtually untapped, and, ironically, about 90 percent of the salt used in Oklahoma is imported. Chemical data on the rock salt are lacking, but evaporated salt produced from brines is generally 97 to 99 percent pure. Current production from three solar-evaporation plants is used mainly for stockfeed, recharging water softeners, and deicing roads. Potential uses are in the chemical industries, where salt or brine is a necessary raw material.

Jan 1, 1973

By Pierre Longtin

"Replacing the aging roadway access to the iconic Golden Gate Bridge, thereby ensuring traffic safety and robustness in case of seismic occurrences, provided an opportunity for major design improvements as well as the development of a parkway that would include the construction of four new tunnels. With an eye to the future, the Doyle Drive replacement project aimed to meet the highest standards for environmental stewardship beyond regulatory requirements. Understanding that lighting equipment is the tunnel‘s subsystem that uses the most energy, the operator was looking for a sustainable solution to light the tunnels. An Intelligent Lighting Control System (ILCS), designed specifically for road tunnels, was acquired to individually control the almost 2000 luminaires lighting the four tunnels. This paper will show the results in terms of energy and operational savings generated over the nine months of operation between the commissioning and the conference in April 2016. INTRODUCTION Electrical & mechanical (E&M) equipment represents an average of 10 % of a tunnel total construction cost. Once the civil infrastructure completed, E&M equipment drives the main part of the expense during a tunnel useful life. Table 1 below describes the impact of various types of energy consumption and their cost impact in tunnels of less than 500 m. It is clear that lighting is the sub-system that requires the most energy. A good lighting strategy is the key to reducing energy consumption due to lighting and a viable solution that will bring important savings in tunnel operations.With a price of $0.14/kWh in California and a planned increase between 3% and 6% per year during the period 2013-2040, the tunnel operators could not afford to overlit the tunnels—particularly when they have to operate it for the next 30 years. However, they also need to maintain the right lighting level to ensure driver safety all the time. The Presidio Parkway project includes the Battery tunnels, which are 240 m (790 feet) and 230 m (750 feet) in length, and the Main Post tunnels, which are 280 m (920 feet) and 315 m (1030 feet) in length."

Jan 1, 2016

By J. D. Miller, C. L. Lin

From mine to mill, the 3D characterization of particles ranging in size from meters to micrometers is now possible. A brief review of X-ray tomography for mineral processing is given with recent advances considered, such as high-speed scanning and image analysis procedures to describe important particle properties, including size, shape and composition. Considering these new 3D characterization tools, applications in mineral processing are discussed for high-resolution X-ray microtomography (HRXMT) laboratory analysis of particles ranging from 20 mm to 5 μm, with a voxel resolution of about 1 μm, including (1) multiphase particle characterization by HRXMT and comparison with scanning electron microscopy (SEM), (2) particle damage state as a result of blasting/comminution, (3) liberation characterization to describe expected separation efficiency, (4) exposed grain surface area analysis to explain the flotation of locked particles, and (5) floc size, shape and water content for polymer-induced flocculation. Finally, applications in mineral processing for plant-site analysis using high-speed X-ray computed tomography (HSXCT) are examined, including, for example, coal washability analysis, the analysis of crusher plant products, and the analysis of pebble phosphate products from central Florida. Scanning rates on the order of 1 kg/min for particle sizes ranging from 150 mm to 1 mm are possible, with a voxel resolution of about 100 μm. For coarse particles smaller than 5 to 10 mm, high scanning rates of more than 300 t/h may be possible at a voxel resolution of about 1 mm.

By John J. Sammarco, Alan G. Mayton, Elaine N. Rubinstein

Researchers from the National Institute for Occupational Safety and Health (NIOSH) developed a light-emitting diode (LED) area luminaire called the Saturn and conducted a laboratory study using a Fletcher High Dual-boom Mast Feed (HDDR) roof bolting machine. The Saturn luminaire was designed to (1) enhance floor illumination to enable better detection of trip hazards in the interior spaces of a roof bolter and (2) reduce glare that has typically been an issue of concern on roof bolters. This paper reports on the results of achieving the second objective. The existing roof bolter lighting was the baseline and was compared with three versions of the Saturn luminaire relative to light intensity (100%, 75%, and 50%). Discomfort and disability glare data were obtained from 30 participants that comprised three age groups. Discomfort glare perceptions were obtained using the De Boer rating scale, and disability glare was quantified by using Mars Letter Contrast Sensitivity tests. Discomfort glare was reduced at least 3 levels with all Saturn versions. Also, a predictive model was used to estimate discomfort glare, and the results were similar. Disability glare was the least for the Saturn’s 50% intensity, and all Saturn versions had significantly less disability glare than with the baseline lighting. Veiling luminance was calculated and used as another indicator of disability glare. Veiling luminance was 28 to 42 times greater with the baseline lighting as compared with that of the Saturn lighting. Lastly, visibility levels were calculated. The Saturn versions were 4 to 6.5 times better in terms of visibility level.

By Ronald R. Hartman

I can recall a time 10 or 12 years ago when I spent a pleasant Sunday afternoon driving to Jim Thorpe, Pennsylvania to see a carnotite deposit that had recently been discovered. The announcement of the discovery stated that it was in the Pottsville conglomerate in a road cut along the highway. To my surprise, the highway was lined with cars and every weekend prospector for 100 miles had come to see the ?big uranium deposit of the east?. I literally had to stand in line to make a measurement with the scintillation counter I had with me. The thought at first occurred to me that this is evidence of how thoroughly the surface of the United States must have been prospected, more likely, perhaps it points out quite the opposite. A lot of time and energy was being spent in tracing the footsteps of others and a lot of time was spent looking for the obvious occurrences. The point is, that in the early days a tremendous amount of uranium exploration was carried out but few systematic surveys were made. Thorium anomalies were usually discounted after cursory surface field checks. Conversely, in airborne surveys - anomalies due to elevation changes or thin over- burden on hilltops were often investigated more thoroughly than smaller indications on hillsides and valleys. An adequate supply of uranium was nevertheless found due to the ingenuity and persistence of the geological profession and the public in general. This ?adequate? supply, like so many estimates for raw materials turned out to be far too low.

Jan 1, 1967

By A. L. Hornbaker

Colorado has recorded more than 100 years of industrial mineral production. Much of the state's history, culture, and economy is based in mining, but the industrial minerals and construction materials comprising the nonmetallics sector of the industry very often are overlooked or overshadowed by mineral fuels and the metals. Indeed, many of these materials find use in seemingly unimportant industrial applications essential to our economy and life style and yet are not so recognized by the consumer. Unlike many other mineral resources, the numerous industrial minerals occur in many different and often exotic geologic environments, some of which are characteristic only of the western states. In Colorado only a few of these minerals have continued production through the years; many saw only "boom" periods or other critical times of need, such as the world wars. The changing needs and demands of our society in the 1980s will stimulate yet another era of intensive activity in our industrial minerals storehouse. Researchers are finding new uses and applications for these materials in dealing with the energy crisis and fuel shortages, the need to develop domestic mineral reserves of all kinds, and the goals of reuse and recycling. Some of Colorado's little-used and unused industrial minerals hold extraordinary promise in solving some of these problems on the regional and national levels. In this paper we will look at the history of development of Colorado's more prominent nonmetallics and especially at current research on and future potential of several other commodities among which Colorado contains the largest known reserves.

Jan 1, 1980

By Matthew S. Sanchez, Richard J. Lee, Matthew D. Zock, Drew R. Van Orden, Yumi Kamiya, Edward B. Ilgren

In many developing countries, asbestos is still used for friction products, insulation, and asbestoscement products. However, there is very limited modern data evaluating the airborne concentrations of asbestos fibers in operating asbestos plants. We have conducted an Industrial Hygiene survey, using state of the art PCM and TEM analysis, of a Bolivian asbestos cement plant that uses crocidolite during the production of roofing shingles and water tanks. The study is the first to use modern analytical measurements in an uncontrolled asbestos environment. Thus, this study offers insight into the historical airborne exposures at asbestos plants operating before modern dust control measures were introduced or airborne fiber levels regulated. The results suggest that fiber concentrations are far in excess of those for which current models would predict the onset of asbestos disease and mesothelioma. Significantly, the plant and community do not have an elevated incidence of asbestos disease or mesothelioma. Airborne fiber levels during comminution and fiber sizing ranged from 100 to as much as 1,000 f/cc. Fiber levels in the mixing, forming and finishing areas ranged from 0.5 to 9 f/cc. Based on the number of overloaded samples and estimates of their concentration, historical estimates of exposure may be underestimated by an order of magnitude. Also, an excellent correlation (1:1) between the PCM and TEM fiber concentrations (for fibers _0.25 um diameter) were obtained, raising questions about the conventional wisdom that the PCM systematically undercounts fibers. The results of this study further indicate that current models may overestimate the risk of asbestos disease and mesothelioma.

Jan 1, 2012

By Nick Hasenack

In the pelletizing plant of Hoogovens, Estel BV, a varying mixture of hematites and magnetites is used for the production of acid and (occasionally) fluxed pellets. Optimum results regarding productivity, quality and process control are obtained with mixtures containing 30-40 % magnetites. A decrease of the magnetite ratio or an increase of the basicity has a great influence on both productivity and heat and power consumption. Tests have been carried out to find the extent to which magnetite can be replaced by b.f. dust, mill-scale and coke breeze. Pilot plant tests show that about 80-100 % of the production loss due to a decrease in magnetite content or to the increase in basicity can be regained without damage to the quality by adding coke breeze. The amount of coke breeze should be limited tot 1,5 %; if this percen¬tage is chosen higher, the quality of the pellets deteriorates rapidly. The amount of coke breeze to be added should be about 30 % above the theoretical value, based on heat balance considerations. The results achieved by incorporating b.f. dust and mill-scale into the pelletmix were also encouraging, but as some types of mill-scale are very difficult to grind and the supply of b.f. dust is limited, the research has not been carried out extensively in this field. The pilot plant tests on replacement of magnetite by coke breeze have been followed by industrial tests, during which the breeze was added to the ore feed before the dry-grinding system.

Jan 1, 1977

By Nikhil Dhawan, SHAILA MIR

The emerging problem of electronic waste has promoted the interest in exploring metal recovery from secondary sources under the umbrella of urban mining. This study presents the physical and chemical characterization of various components present in end-of-life laptops to help ascertain the sites of metallic values and develop sustainable and environment-friendly recycling. The recycling potential of a laptop is evaluated by sequential disassembly, separation, and characterization of components such as body (49.8 wt.%), printed circuit board (9.7 wt.%), hard disk drive (4.9 wt.%), and battery (12.4 wt.%). The printed circuit boards comprise metallic values, majorly copper (25 wt.%), tin (5.8 wt.%), and lead (3.1 wt.%). The precious metals (Au, Ag) with an economic advantage are abundantly present in electronic components such as integrated circuits, capacitors, resistors, and processors. Critical elements such as lithium, cobalt, and rare earth elements are detected in the discarded laptops' batteries and hard disk drives. The recycling potential representing the amount of material that can be recycled in various components, depending on the type, concentration, and purity, is determined in the range of 36–100%. On average, a unit laptop contains~ 386 g of Cu (14.45 wt. %), 49.73 g Co (1.86 wt. %), ~346 mg Ag, ~141.2 mg Au, ~650 mg of rare earth elements (Nd, Dy). This study presents a database for investigating integrated and economical recycling techniques from different components of a laptop, and an overall process flow is also proposed.

Jul 24, 2021

Scattered north and south along a 161-km (100-mile) stretch of Interstate 80, Newmont Min¬ing Corp. owns four active mining properties in Nevada?s northern high desert ? Carlin Trend Operations, Midas, Twin Creeks and Phoenix. Among the four, there are nine openpits, five underground mines and 14 processing facilities. While gold is the predominant ore, silver and copper are also produced. And in a move to hold down energy costs, Newmont built and owns the 200-MW (net), coal-fired TS power plant. This plant provides about 65 percent of the power used for Newmont?s own operations, while the rest is sold to NV Energy, which services Nevada and northeastern California. Bringing the Phoenix Mine ? Newmont?s newest in Nevada ? on-line presented many developmental and operational challenges. Located about 19 km (12 miles) southwest of the town of Battle Mountain, the general area had been home to prospectors and other mining companies since the 1860s. But any profitability in developing the lower grade gold, copper and silver deposit at Phoenix proved elusive, with Battle Mountain Gold being the last company to make an attempt. When Newmont acquired Battle Mountain Gold and its Phoenix reserves in 2001, the lower grade of ore was not a deterrent. Newmont found Nevada-wide cost savings synergies for maximizing profit during the depressed gold market of the late 1990s. The new property was aptly renamed the Phoenix Mine, a nod to its rising from the ashes of the dreams and efforts of previous mine owners.

Jan 2, 2010

By Naeimeh Shabani, Hamid Mirzaie, Javid Sadeghi, Hoda Jafarizadeh-Malmiri, Afshin Javadi

Iron oxide nanoparticles (Fe3O4 NPs), despite their small size, are stable and have a large surface area that allows for absorption and removal of ions as well as turbidity in a short period of time. Thus, the present study addressed the synthesis and characterization of Fe3O4 NPs synthesized using the co-precipitation method and evaluated their effect on the coagulation process in water treatment. The Fe3O4 NPs characteristics were evaluated as follows: magnetic properties were measured using a vibrating sample magnetometer (VSM), surface area using Brunauer–Emmett–Teller (BET), crystal phase using X-ray diffraction (XRD), and morphology using field emission scanning electron microscopy (FESEM). In addition, the effects of the synthetic Fe3O4 NPs on the turbidity reduction of water in various pH levels were evaluated. The synthesized Fe3O4 NPs were without any impurity in the sizes of 22–32 nm, surface area of 99.6 m2/g, pores’ mean diameter size of approximately 10.6 nm, and maximum magnetic saturation of 66.21 emu/gram (emu/g). Using 0.2 g of synthetic Fe3O4 NPs with an initial turbidity of 17 NTU and pH of 6 could reduce all water turbidity (100%). Considering the cheap and facile production and separation, as well as the possibility to reuse them and reduce the sludge water content, iron oxide Fe3O4 NPs can be effectively used for turbidity reduction in the water treatment process.

Oct 26, 2020

By James K. Ballard

Leach dumps in Butte are relatively new in comparison with older established dumps in other areas throughout the West. With the exception of one 10 million ton dump, all dumps have been formed on a prepared base. This is necessary because the entire leach dump area overlies an alluvial fill which varies in depth from 100 to 400 feet and through which solution would be lost. Preparation of the leach pad consists of first removing all vegetative material and compacting the exposed surface with rollers. This surface is covered with a 4" layer of minus 1" crushed rock which in turn is roller compacted. A 3" compacted layer of asphalt hot mix is then applied to the crushed rock surface. Final sealing is effected by a 1/4'? coating of catalytically applied hot asphalt. Dump leaching was inaugurated in 1964. First solution applied was wholly made up of mine water pumped to surface through a central pump shaft. Sulfuric acid was added on surface at a surge pond to control pH of the leach solution. Acid addition is necessary not only to benefit the leach dumps, but to prevent the formation of ocher scale within the pipe line distribution system. Mine water pH is on the order of 2.8. The combination of ferrous and ferric iron as well as magnesium and aluminum salts is such that ocher forms at a pH of 2.38. It is therefore mandatory to control pH at 2.0. Dump effluent pH is held at 2.3 or less.

Jan 1, 1968

By T. F. Tomb

Although the number of operating longwalls (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and have in some cases more than doubled. As a result of the increase in production, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Parameters in place to control dust were noted with special emphasis being placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control parameters in place at the time of the visit to dust concentrations measured at the tail, on the tail shearer operator and to the average concentration of dust determined from averaging all the measurements from the occupations sampled. The parameters in place to control dust were also compared to the gamut of technology known to be available to control dust. This paper presents a discussion on the effectiveness of the parameters in place to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1990

By F. Sime, X. Wang, J. D. Miller, T. Akinseye, S. Assemi, L. Pan

Respirable coal mine dust (RCMD) is a complex mixture of carbonaceous and mineral particles with a variation in size and shape. Accumulation of RCMD in the lungs of underground coal miners results in severe respiratory damage and ultimately progressive pneumoconiosis known as the black lung disease. The occurrence of the black lung disease dropped to a low of 2.1% in 1990s but has increased to 3.1% in 2000s [1], prompting more research on coal mine dust mitigation. In addition to surveying the impact of new mining technologies on the size of generated dust and exposure measurement, a comprehensive characterization of physico-chemical properties of RCMD particles are essential for a better understanding of the adverse health effects of coal mine dust. Such vital factors include particle size, surface charge, morphology, composition, and agglomeration state. The respirable fraction of RCMD, has been designated as particles < 10 μm in diameter, and almost all studies on the RCMD toxicity have focused on micron-sized particles. However, recent toxicological studies have shown that nanoparticles (particles with one dimension less than 100 nm) can have a magnified toxicity compared to the larger particles with the same chemistry [2]. Nanoparticles have a much higher specific surface area compared to the same mass of larger particles and are thus more reactive. Most micron-size particles can be cleared by the body’s defense mechanism. However, inhaled nanoparticles can easily deposit in all regions of the respiratory tract and can translocate to vital organs. [2].

Mar 2, 2022

By Serge Moalli

The Ashlu Creek Hydro-electric project, located north of Squamish, BC, at the confluence of Ashlu Creek and the Squamish River, comprises a 49 MW run-of-river project and features a 4.08 m diameter, 4.4 km power tunnel and a 128 m deep drop shaft. The Ashlu Creek Hydro-electric project is being developed by Innergex under Ashlu Creek Investments Limited. Site civil works are being completed by Ledcor CMI of Vancouver with tunnel construction by Frontier Kemper Constructors ULC under a lump sum design-build contract. Site works got underway in September 2006 with the construction of the tunnel portal and laydown area. These site works required rock slope stabilization over a 50 m rock slope to secure the laydown area as well as the construction of a tail track muck tipping station and structural wall to facilitate TBM excavation and spoil removal. Starter tunnel construction commenced in early 2007 and TBM tunneling started in the late spring of 2007 and is planned to continue until early 2009. The power tunnel is being excavated using a 1,200 kW Wirth open-type hard rock TBM dressed with 31?17&apos; cutters. The TBM featured two fixed mounted rock bolt drills behind the finger shield: these were removed and replaced with jacklegs to improve access. A probe drill at the end of the main beam is also present. The geology along the 4.4 km power tunnel comprises very strong and generally massive granitic bedrock with rock strength greater than 225 MPa. A unique feature of the project is that no subsurface investigations have been completed for the tunnel however extensive bedrock outcrops are present along the Ashlu Creek valley. A historical quarry exists approximately mid-way along the tunnel alignment that has exposed good quality granitic bedrock. TBM tunneling to date has achieved advance rates of 10?20 m/day with a maximum of 23 m and has encountered all of the anticipated six major fault zones where the installation of various standard high capacity tunnel support was successful to facilitate TBM advance through these sections.

By Krawiec Alfons

The threat of rock bursts along with the danger from methane gas and coal dust explosions belongs to particularly dangerous phenomena in Polish pit-coal mines. This phenomenon results mainly from the physical-mechanical properties of the rock mass as well as the geological-tectonic structure of the Upper Silesian Coal Basin. In the postwar years in Polish coal mining thanks to a multi- directional activity, a decrease of rock bursts and their effects has been noted. For example, the number of rock bursts reported in 1965 amounted to 71 in comparison to only 23 in 1974. The ratio of rock bursts calculated for 100,000 tons of coal extracted from rock bursting strata amounted to 0.08 in 1965; however, in 1974 it amounted to 0.023 /Fig. 1/. These results were obtained in face of a continually growing potential threat from rock bursts caused by the systematic increase of extraction from rock bursting strata, exploitation at gradually greater depths along with the extension of exploitation into deposits enclosed in different types of pillars and other parts of deposits surrounded by workings. Despite the achievements of science and mining practice in this field, this threat has not yet been fully studied and controlled as it should be, As a result, research on preventing rock bursts is being continually widened in Poland. This research has a complex, multi-staged and long-range character. Theory, laboratory and field work in the mines are working on a solution to the problem.

Jan 1, 1976

By Scott A. Norby

Kennecott&apos;s Ray Mines Division (RMD) is located in central Arizona. The pit and silicate plants are located at Ray while the 27,500 tpd concentrating facilities are located at Hayden, approximately 20 miles away from the pit. Ore is delivered in 100 ton railroad cars, 60 cars per train via the Copper Basin Railroad. The side discharge cars are dumped into a 6,000 ton trackhopper. There are 6 Nico feeders, two per belt. Three 48" belts transport the -8" ore to three 7&apos; standard (secondary) Nordberg crushers. Each crusher is preceded by a 6&apos; x 12&apos; Tyler double deck screen. The secondary crushers are open circuit. The -1/21t material from the screens is transported directly to the fine ore bin at the mill. The discharge from the crushers and the intermediate product -2 1/411 x +1/2" is conveyed to a surge bin. The tertiary crusher feeder belts discharge onto five 61 x 161 Tyler double deck screens, each followed by a 7&apos; shorthead (tertiary) Nordberg crusher in closed circuit. The -1/2" product joins the -1/2" ore from the secondary crushers and both are conveyed along a 42", 4,230 foot long belt to the fine ore bin that feeds the grinding circuits. When hard ore is experienced at the concentrator the daily throughput decreases by up to 10%. This coupled with the fact that the ore is generally becoming harder with mine depth provided the incentive to improve the performance at the crushing plant.

Jan 1, 1986