Search Documents

By Claus Becker

At the RETC 1979 in Atlanta/Georgia it was reported about the beginnings of the Hydroshield system and the first site experiences. Since that time over 10 miles of tunnels in various diameters have been built with that system, and the discussion of the two most interesting projects will be the main topics of this paper. AURELIA TUNNEL, ROME In Rome, the railway system is going to be completed and modernized. Therefore, it is necessary to tunnel through the Roman hills. Part of the new railway system is the Aurelia Tunnel, located some 100 feet below the famous Via Aurelia Antigua, close to the Vatican. The double track railway tunnel has an internal diameter of 9.44 m and a length of 2.410 m. It runs through completely differing soil conditions. (Fig. 1) The first 1000 t are situated in watertight clay, the rear part in water bearing loamy, clayey sands with interlayers of loamy clays. The figure shows the soft change-over from clay to sand. The groundwater head is between [ ]

Jan 1, 1983

By F. M. Swain

High-calcium limestones occur in the upper part of the New Market Formation, of Lower Middle Ordovician age, in Franklin and Cumberland Counties, Pennsylvania. The high-calcium facies of the New Market Formation is represented by sublithographic limestone or vaughanite, which probably formed in quiet water; low-energy environments such as intershoal lagoons, or in protected bays similar to the present-day Florida Bay environment. Rapid facies changes are characteristic of the strata. The better grade of stone lies in the upper 100 to 125 feet of the New Market Formation and averages 95-97% calcium carbonate. Silica and magnesia are about equal in amount as impurities. One high-calcium belt extends from the Maryland state line through Chambersburg and Newville to beyond Carlisle. The strata in this belt are structurally complex, which requires careful field study' and core-drilling prior to exploitation. Stone suitable for blast-furnace flux is present in relatively large amounts, but stone for open-hearth use or portland cement requires more selective quarrying.

Jan 1, 1966

By J. E. Murphy, L. A. Walters, F. H. Nehl, G. B. Atkinson

The US Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A h/150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 msecs. Graphite, lead and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70°C (158° F) gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10% to 30%, and a period of 100 msecs to 1000 msecs gave the following results: Ag concentrations decreased from 34 µg/mL to 0.1 µg/mL. Au concentrations decreased from 54 µg/mL to 0.2 µg/mL and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 1995

By Chris J. Conway, Bruce W. Atkinson, Graeme J. Jameson

The flotation of coal in the fie and coarse particle size ranges presents particular problems. Fine or ultra-fine coal less than 100 microns presents a challenge to conventional flotation machines because the rate of capture of the coal particles can be very low, so longer residence times are needed. Also, conventional mechanical cells are not normally designed with froth properties in mind. Froth drainage may be inadequate, leading to excessive entrainment of ash. The upper limit of flotation of coal is normally put at about 500 um (30 mesh). It appears that, in mechanical cells, coarser particles tend to be torn away from bubbles in the turbulent environment created by the impeller. In this paper, results are presented from plant trials of a high-intensity flotation column of novel design, namely the Jameson cell. Extensive trials have been conducted on coal slurries with a top size of around 1 mm. Size-by size analysis shows that it is possible to achieve high yields of low ash product over the whole particle size range.

Jan 1, 1995

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of a massive pillar failure in a room-and-pillar mine. The mine employed a nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated out by quickly, and, within 24 hours, it had covered an area approximately 1,250-m- (4,100 ft-) long by 762-m- (2,500-ft-) wide. The failure was caught and stopped by a solid barrier pillar. Using computer modeling, this study indicates that the massive failure was initiated because of a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of the absence of barrier pillars between some panels and between mains and panels. Based on computer modeling, alternative mine plans were proposed to avoid such problems.

Jan 1, 2002

By A. E. Dabbagh

Saudi Arabia’s mineral potential offers development target that compliment the national effort to diversify the income of this oil and gas economic based nation. Ma’aden, a joint stock company with paid-up capital of US$1 billion, has from its inception in 1997, actively developed in-house engineering and management skills to transform the Arabian shield’s mineral potential into such real projects. Gold mine operating facilities of 100,000 oz/yr underground and 50,000 oz/yr open pit are de-scribed, as well as 3 targets, two of which are underdevelopment; Al Hajar (3,000 tpd at 2.5 gpt Au)and Al Amar (5,000 tpd at 20 gpt Au). Emphasis is also on exploitation of phosphate rock and down-stream fertilizer products, based on the Kingdom’s107,000 sq. km. northern basin geological reserve. Al Jalamid, the prime target, represents 216 million tonnes of these P2O5 reserves. Saudis and expatriates, together, lead international engineering companies and contractors operating and developing these facilities.

Jan 1, 2000

By Merwin Bernstein

Peru has been an important source of metals since Aug. 29, 1533. On that day Francisco Pizarro took charge of the 24 t (772,000 oz) of gold and silver that constituted Atahualpa’s ransom. At today’s prices, the value of that booty ranges between $100 and $150 million, depending on the proportion of gold to silver. Since then, Peru’s silver and gold production has been legendary. Current mine production Most of Peru’s metals are mined from the Andes Mountains and its foot-hills. The Andes run the length of the country parallel to the Pacific coastline from Ecuador to Chile, a distance of nearly 3000 km (I 875 miles). They are about 300 km (187 miles) wide and much of the range is more than 3000 m (9900 ft) in elevation. High plateaus (altiplanos) occupy a large part of the range. Both flanks are rutted by large valleys and canyons. Many of these peaks are prodigious. which make road building expensive and adds to the cost of mining.

Jan 1, 1993

By Hassan Madani

Kushk lead-zinc mine is located in central part of IRAN. The mine is owned by Bafgh Mines Co., which is a nationalized company. Exploration results show that ore occurs in the area that extends for 800m length and 180m depth. The approved, probable and possible reserves of the mine is 900,000 tons, 1,120,000, tons and 1,450,000 tons respectively with average grade of 17.7% zinc and 4.3% lead. The total annual output of the mine all was by underground mining, is in the order of 100. 000 tons. The main entry to the mine is via an inclined shaft with a cross-sectional arp of 8 m2, length of 263m which dips at 20°. The ore is mined mostly by sublevel stopinq method. The major difficulty in ventilating the mine was that related to spontaneous combustion of pyrite, which was more serious in some parts of the mine than others. In order to reduce this risk, a new ventilation system for the mine was designed, using 4 exhusting fans.

Jan 1, 1991

By Howard A. Jongedyk, Jerry Wachtel

Advancements in tunneling technology and underground construction, plus rapidly rising costs of land, and a higher priority being placed on urban esthetics, make tunnels a more attractive option for certain portions of the highway construction program. Recent emphasis placed on fuel conservation reinforces the need for tunnels as a means of shortcutting circuitous routings designed to avoid potentially undesirable environmental impacts on any given area. Larger and more complex tunnels which have been constructed in recent years attest to this greater interest. More than 100 major highway tunnels are in operation in the United States. Highway tunnels commonly have much higher initial cost compared to surface routes. Where extensive cut and cover is involved, temporary disruption of the surface area may prove costly. In exchange for these costs, certain environmental advantages result. The purpose of this paper is to discuss some of the environmental advantages of highway tunnels and some of the unsolved problems related to obtaining maximum use of highway tunnels and research underway to help solve these problems.

Jan 1, 1974

By George A. Lawrence

A new super-large 100 m3 (3500 ft3) pneumatic mechanical flotation cell is now available to meet today's mineral processing challenges. Several innovative design concepts represent a marked departure from conventional flotation cell designs. The radial discharge from the pump action rotor and the overhung vane type stator is contained in a conical bottom round tank with no dead comers. Peripheral launders collect froth overflowing the entire circumference of the tank and these launders are of a hexagonal design permitting cells to be nested together in a honeycomb fashion. The mechanism drive is either a customized right angle gear reducer or a conventional Vee belt drive. Both drive systems are available with an optional variable frequency control system that permits infinite speed adjustment of the rotor in each flotation cell or group of cells. Results of side-by-side comparative testing between three major manufacturers of super-large pneumatic mechanical flotation cells are discussed. These results were obtained at a large copper concentrator in Chile during several weeks of commercial scale testing.

Jan 1, 1995

By Staff

GENERAL DESCRIPTION The Lucky Friday mine is located in Mullan, Sho-¬shone County, Idaho. The mining method is horizontal slice cut-and-fill (with timbering for support or un¬timbered) using hydraulic sand. Cemented sand fill at a 1:17 ratio is used in sill pours and at a 1:7 ratio for the final 152 mm (6 in.) capping in successive stope floor pours. Annual production with 100% cut-and-fill mining is 167 829 t (185,000 st). The average depth of mining is 1296 m (4250 ft) and the average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size The ore body is 396 to 488 m (1300 to 1600 ft) long on strike, 1421 m (4660 ft) on dip, with an average width of 2.3 m (7.5 ft). Dip varies from vertical to1.2 rad (70°) Ground Conditions, Ore Value, and Production Requirements The ore body contains quite strong argentiferous galena and quartz. The hanging wall and footwall are strongly sheared and fractured. Ore value is $211/t ($192/st).

Jan 1, 1982

By Paul D. Tavares, John Forbes, Eric R. Drooff

As the existing major U.S. - Canada rail tunnel was too small to accommodate double-stack container cars, Canadian National Railways is constructing a new parallel tunnel with a 50% greater diameter. Starting in Sarnia, Ontario, the new shallow-cover bored tunnel runs under a large research building and several other structures in an oil refinery before travelling under the St. Clair River. Maximum predicted settlements to be caused by the 9.2 meter diameter earth pressure balance TBM in the soft St. Clair till were in excess of 100 millimeters. As such, these settlements had the potential to cause severe damage and disruption to the existing refinery. In order to reinforce the soft clays below the refinery research building and other structures, and to compensate for settlement caused by the tunnelling, the ground improvement method of Soil Fracture grouting was successfully applied for the first time in North America. This paper will describe the details of both the soil fracture grouting application and the elaborate electrolevel remote monitoring system used.

Jan 1, 1995

On longwall coal faces in some Japanese coal mines more than half of the air coming from the intake gate road flows into the caved goaf and the air heated by the hot waste rocks in the goaf comes out through the latter half of the face. This still constitutes a major heat problem in spite of the introduction of gate and face air coolers. Therefore, in order to establish effective measures to improve the environ- mental conditions, it is essential to obtain information pertaining to the air flow pattern on the face as affected by the goaf conditions and the air flow regulating measures taken at the intake side of the face. Experiments for this purpose were carried out using a coal face model. The model was reduced to a scale of 1110th of the real face measuring 100 m long and 2.2 m high, equipped with self-advancing supports. The model design was also conceived to accomodate eventual modifications of the space of the caved goaf as imposed by the actual conditions.

Jan 1, 1980

By M. S. Janssen

The development of a design equation for, and the testing of, a constant- flow airlift pump IS described. The predictions of the new airlift model agree with the results of experiments carried out using riser diameters between 0.025 and 0.300 m, submergence depths between 5 and 10 m, suspension densities between 1000 and 1650 kg/m3, and a solids dg of 70 to 100µm. The predictions o the model also agree with data from the literature for submergence depths that reached 130 m. This airlift model was employed to simulate the pulp flow through a series of tanks, each of which was fitted with an airlift pump to transfer the suspension to the next tank. Particular attention was paid to the riser diameter, submergence of the airlift pump, and control of the air supply to the airlift pump during the simulated operation of a series of tanks. The results of the simulation highlight some design parameters that could affect the efficiency and operation of a plant that employs airlift pumps to transfer suspensions.

Jan 1, 1989

By Richard A. Thomas, Liming Yuan, Lihong Zhou, James H. Rowland

Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners.

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By Felix Schmid

ABSTRACT Lateritic bauxite deposits of economic size and grade in Sierra Leone occur on granulites of the Kasila series. The high grade trihydrate ores of Mokanji are exploited by SIEROMCO since 1964. Remaining reserves are small (2 million tons) and operation moved over to the Gondama deposits of similar grade. Port Loko bauxite reserves are estimated at 100 million tons and are of relatively lower grade. It is planned to treat this ore locally into alumina. Guinea's bauxite reserves exceed those of any other nation. They occur as hard lateritic bauxite covers on plateaus of the Pre-Cambrian sedimentary formations and on doleritic intrusions. The genesis is still controversial. The Sangaredi mine has produced high grade ore for the last 10 years. Friguia exploits a relatively lower grade ore at a rate of about 2 million tpy to be treated in their local alumina plant. Kindia ore is mined at a yearly rate of 2,5 million tons since 1974. Untouched reserves at Ayékoyé and Tougué/Dabola are estimated at 6,000 million tons.

Jan 1, 1984

By O. Alvarez-Campos

Two porphyry copper orebodies, the North and Central MM orebodies, have been found through regional and structural geologic works, about 5 Km south of Chuquicamata, under a gravel bed of approximately 100 m and in the west side of the West Fissure. The mineralization is emplaced in a coarse granodioritic porphyry, predominantly with sericitic alteration. In the North MM ore-body, with 200 million metric tons of 1.0% Cu, the mineralization is mainly chalcopyrite, bornite, digenite and molibdenite. In the central MM orebody, with 700 million metric tons of 1.3% Cu, there are large veins of enargite, chalcocite and bornite, the last one increasing in depth, separated by chalcopyrite and pyrite zones; in these veins there are interesting gold and silver values. Both orebodies have an upper enrichment of chalcocite and covellite, with pyrite envelope. According with these characteristics, the MM orebodies could he the upper part, with sericitic alteration, of the Chuquicamata porphyry copper system, displaced by the West Fissure system movements, but we couldn't eliminate the possibility that MM can be a new orebody, different of Chuquicamata.

Jan 1, 1993

By John W. White

Anthracite mine refuse, or culm dump material as it is sometimes called, is the waste material resulting from the sizing and cleaning of run-of-mine deep and strip-mined anthracite coal. It may also contain mine rock, carbonaceous shale, pyrite, and other debris from mining operations. This material is generally stored in piles or banks, some of which are over 100 years old. Many of the older banks contain a considerable amount of good coal, particularly in the finer size ranges, since these sizes did not have any particular economic value in the early days of anthracite mining. Today, the refuse material from a cleaning operation must be piled in an orderly fashion and in such a way as to minimize the tendency to ignite. There are well over 400 of these banks in the anthracite region containing over 1100 million tons of refuse located in the north-eastern part of Pennsylvania. The banks range in size from a few thousand tons of material up to as much as 13 million tons. Most of

Jan 1, 1972

By Pinar Eksert, Hakan Akcin

Investigations show that injuries and fatalities in mining workplaces in developing countries are increasing. In Turkey, the number of workers killed in occupational accidents in the Zonguldak Hard Coal production region per 100,000 tons of coal production is 2.83 in the private sector and 2.03 in the public sector. For this reason, it is important to conduct risk analyses in terms of occupational health and safety and to implement measures quickly. Risks are evaluated with reactive and proactive approaches. Because hazards and events are often unpredictable in high-risk areas such as coal mining, it is not practical or meaningful to plan proactively in advance for every possible situation underground, especially psychosocial risks. However, it is important to develop protective strategies and measures for unexpected events or to take a reactive approach to prevent future incidents or accidents and to identify psychosocial risks. Therefore, reactive risk assessments based on the tactics and strategies of criminology can be conducted and spatiotemporal geographic information system (GIS) techniques can be utilized, enabling managers in mining workplaces to correct assessments.

Oct 1, 2024