Search Documents

By John Hillman

The reconstruction of the British mining industry which began shortly after nationalisation in 1947 continued until well into the 1950s with the support of the Government. This support diminished as plentiful supplies of cheap oil from the middle East made many coalmines un¬economic. The planned rundown which followed was foreshadowed in the 1965 White Paper which outlined the financial measures to speed the closure of uneconomic collieries. The decline appeared likely to continue into the 21st century as the role of coal in UK energy requirements became less and less significant. This policy was well on course in 1973 when the oil crisis led to a complete reappraisal of the position. A Government examination in 1974 of the coal industry then supported the National Coal Board's general strategy of major capital investment as set out in its 'Plan for Coal' (1). Plan for Coal aimed at halting the intended decline in the industry's capacity and restoring it to 120 million tons of deep mined output in 1985. The Plan proposed action along the following lines (a) increase output by major Investment in construction at existing collieries with sufficient reserves to give 13 million tons per annum extra output (b) invest in extending the life of existing collieries by gaining access to additional reserves, to give 12 million tons per annum extra output © by sinking new mines, produce an extra 20 million tons per annum. Figure 1 shows the contribution (2) expected from each of the three sources up to 1990/1. The measures taken were expected to offset the inevitable exhaustion of existing pits and provide the additional 40-42 million tons capacity needed to restore annual output in 1985 to 120 million tons. Parallel to this programme for expansion of deep mined output, opencast mining was to produce 10-15 million tons per annum. A recent review however, indicates that new mines are likely to yield only 10 million tons per annum by 1985, mainly owing to the need for public inquiries into proposals for new mining and the resultant fact that planning approval takes 'much longer than originally expected. Nevertheless the objective of 120 million tons deep mined output by 1985 is still considered achievable of means of a greater contribution from existing mines. This programme was originally estimated to cost 2,-56 million dollars at March 1974 prices, out revised estimates of the cost of Plan for Coal indicate that it may now exceed 6,960 million dollars at mid-1977 prices. Plan for Coal includes a substantial investment in new and reconstructed coal preparation plaints. At mid-1977 prices more than 322 million dollars Ls so be invested in coal preparation projects in the UK, at the rate of, about 70 million dollars a year. This rate 3f capital expenditure has been maintained over the past three years and covers investment in a wide range of coal preparation coals for the power station, coking and domestic markets.

Jan 1, 1978

By V. Svalbonas

With the occurrences of serious mill structural failures on both ball and primary mills, the mining industry has entered the era of detailed fabrication specifications. Such specifications, however, have been developed as individual entities, often by people not related to the mill design function. Therefore, there has been no effort to relate mill failure or safety to the existence or elimination of specific fabrication flaws; that is, no cause-effect failure relationships have been developed. The omission of this step produces a specification which can be termed uneconomical at best. The present paper attempts to fill this void, by reviewing methods for design consideration of flawed structures, and describing experimental tests used to tie such data to a meaningful quality assurance program in fabrication.

Jan 1, 1985

The use of controlled recirculation can be dated back to the early 1930s. Although this method has been applied in many mines since then, a generalized comprehensive network analysis is still lacking. This paper presents a unique approach in which the ventilation network with a controlled district recirculation is divided into two subsystems: a main subsystem and a recirculation subsystem. The subsystems are analyzed individually and the results and their relationships are then integrated into discussions of the total ventilation system. The analysis of the recirculation subsystem is facilitated by introducing a non-dimensional parameter A, which represents the ratio of the air quantity for the working face to that for the subsystem. As a result, fan and regulator pressures and air power for various recirculation arrangements can be effectively expressed as a function of A and the subsystem air quantity. Numerical examples are included.

Jan 1, 1995

By S. L. de Moraes

This study aimed to identify a way to reduce the use of bentonite in the pelletization of magnetite. With this goal, different combinations of binders were compared to bentonite by examining the quality of pellets obtained by balling drum agglomeration. Pellets were subjected to routine tests that included simple compression of the wet and dry 105°C pellets, dropping wet pellets to determine their ability to survive handling and submitting pellets to thermal shock to determine how they tolerate drying and preheating. The best results use sodium silicate (1.5%) as a binder and show that it is possible to pelletize iron ore without using bentonite.

Jan 1, 2010

By S. C. Suboleski

Forecasts indicate that the acid rain bill currently before Congress is likely to cause an increase in demand of 30 to 40 million tons per year of compliance quality coal from Central Appalachia. This represents a doubling of this segment of the coal business. This paper will examine how this doubling can be met, what the likely implications for pricing are, the major uncertainties associated with these predictions, and the likely outcomes of the growth in compliance coal. Finally, some implications for fuel planners will be discussed.

Jan 1, 1993

By W. E. Benton

The name Perlite applies to both a hydrated volcanic glass containing from 2% to 5% combined water and to the lightweight material that is produced from expanding the sized volcanic glass. Upon heating, Perlite expands to about twenty times its original volume which results in a material of low density, low thermal conductivity, and high sound absorpt'ion. Perlite ore is mined by open pit methods and is crushed and sized to provide specific gradations for expanding into products used in acoustical tile, built- up roofing, filtration, lightweight concrete and horticultural applications, among others. In 1983, the U.S. production of crude Perlite came from 12 mines and 6 western states, with apparent consumption and production estimated to be about 6% lower than 1982. The average price per ton was slightly higher than in 1982.

Jan 1, 1984

By Kim Lapakko

Increasing public concern over the welfare of the environment has placed demands on the mining industry to evaluate the environmental impact of mining development. This is a difficult task and involves considering the influence of a multitude of variables on complex processes over a long time period. Few studies which focus on the evaluation of the environmental impact of mining have been conducted and, therefore, there is little past experience to rely upon. This article describes some of the work done to evaluate the potential environmental impact of mining development in Minnesota. Interest in developing the major copper and nickel sulfide deposits near the wilderness areas of northeastern Minnesota aroused concern regarding the environmental impact of mining development in the region. As a result laboratory and field studies were initiated to investigate the potential for trace metal leaching and acid generation due to dissolution of Duluth gabbro. Chemical equilibrium computer modeling was conducted to aid in data interpretation. The goals of the study included the investigation of leaching mechanisms and rates of release (1, 2).

Jan 1, 1980

By Kot F. Unrug

When reading different studies discussing trends in coal mining, it appears that a substantial expansion of output by the year 2000 is predicted, even in the most pessimistic forecasts. Depletion of shallow, easy-to-mine deposits is only a matter of time, and the future average mining depth will increase. The proportion of slope to shaft mines operated during the next decades will change in favor of the shaft mines. Since an increasing amount of shafts in new nine developments seems to be inevitable, it appears appropriate to focus more attention on shaft design criteria. Some valuable papers have recently been published (1) that emphasize geotechnical aspects of shaft design. In the discussion that follows some other aspects of design criteria will be evaluated.

Jan 1, 1984

By John A. Wolfe

The concepts of sea floor spreading and plate tectonics provide more logical explanations of some geologic processes than were possible a few years ago. I plan to premise my discussion of the regional features of Philippine porphyry copper deposits on this tectonic basis, recognizing that parts of the picture can be explained in other ways, but in the belief that this is the best explanation of the whole. The sequence of events which results in the formation of Porphyry deposits (Figure 1) can be summarized as the result of collision of crustal plates, subduction of the oceanic plate, emplacement of a serpentine ultrabasic diapir, formation of a dioritic magma at depths of 300 to 500 km, rise of the magma to a sub crustal or intra-crustal chamber, eruption of andesitic volcanoes, emplacement of diorite or differentiation of the magma into more acidic products, multiple intrusion of hypabyssal rocks and hydro-

Jan 1, 1973

By Paul R. Thomas

This paper addresses the long-term cost and availability of primary gold production from the Republic of South Africa. Forty-four major producing or developing operations were evaluated. The analyses present estimates concerning 1) total refined gold potentially available from demonstrated resources, 2) annual production potential into the next century, 3) long-term weighted average total costs for underground mine production and surface waste reprocessing, 4) the expected annual decrease in gold production, and 5) the ability of other market economy countries to compensate for the anticipated decline in South African gold output. This paper draws upon the data and analyses of a recent Bureau of Mines, U.S. Department of the Interior, Minerals Availability Program appraisal that evaluated the worldwide availability of gold and silver from primary precious metal operations and as a byproduct of base metal production.

Jan 1, 1984

The extraction and processing of minerals from surface mines and quarries can produce significant fugitive emissions as a result of site activities such as blasting, unpaved road haulage, loading, primary crushing and stockpiling. Uncontrolled fugitive dust emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. Simulation technology is finding increasing use for the purposes of advanced warning of potential problem emissions in addition to providing a basis for future planning applications where demonstrable compliance with regulatory requirements are necessary. The initial re-entrainment and subsequent dispersion of fugitive dust presents a process complicated by the combination of the in pit topography, the surrounding natural topography and the dynamic nature of emissions from these sites. These factors impact upon the accuracy and reliability of the conventional Gaussian plume based computational prediction methods employed for regulatory compliance and IPPC applications. This paper proposes that optimal modelling of open pit emissions may be more accurately achieved by the use of a multi-scale predictive modelling approach utilizing computational fluid dynamics (CFD) methods for high resolution near source dispersion and conventional Gaussian based methods for far field dispersion modeling. This paper presents a numerical based flow and dispersion analysis of a typical UK based open pit utilizing CFD in conjunction with a conventional Gaussian plume based methods. Typical operating emissions and meteorological conditions are obtained from long term data records collected at a large operating quarry extraction operation in the UK. Emissions are modelled using a Lagrangian framework within conventional atmospheric boundary layer (ABL) profiles expressed as functions of turbulence and velocity parameters under assumed neutral conditions. Results are presented in terms of the impact of site topography on in pit retention as compared to the Gaussian based method.

Jan 1, 2009

By A. A. Schweizer

Buckhorn ore is hydrous, argillized basaltic andesite, and is at least 60% clay composed of kaolinite and subordinate montmorillonite. Moisture content runs from 10% to 25%. The original crushing plant was a typical compression type, employing a jaw crusher, and two cone crushers. The system was plagued with constant plugging and unable to meet production plans. The three compression crushers were replaced with a Stamler Feeder Breaker followed by a Hazemag Impactor. Production plans are now exceeded. Agglomeration has progressed from an agglomeration drum to cascading conveyors, to introduction of the lime and cement into the primary crusher.

Jan 1, 1987

By R. A. Hill

A brief explanation of the theoretical functioning of a regenerative system followed by its application to firstly, shuttlecars and then continuous miners and its effect on performance thereof with regard to handling, production and safety.

Jan 1, 1986

By Louis D. Murino

Compared to coal or many metals industries, talc must be considered a small, specialty market catering to niches and dependent primarily on the physical attributes of the mined and processed mineral rather than the chemical attributes with copper, lead or uranium concentrate, the primary objective is the percent metal that ultimately is refined by the smelter, as opposed to the brightness, particle size distribution, trace impurities or morphology. The latter constitute the important determinants of where, how and why talc and similar industrial minerals are used. This paper addresses the talc market-place: where it is, how much of a market there is, who the producers are, available capacity, market growth, and marketing techniques.

Jan 1, 1984

By K. Lang

The use of high-efficiency electrical submersible pumps (ESPs) for large scale, open pit mine dewatering operations provides a good example of how technology, products and services from the oil and gas industry can be adapted to the mining industry. In this case, the mine is Goldcorp?s Peñasquito in the Zacatecas state of Mexico, at the Peñasco and Chile Colorado open pit deposits. The technology, products and services are from Schlumberger artificial lift (AL) and Schlumberger industrial water services (IWS). Overview of high-efficiency ESPs This section provides a brief description of the basic components, specifications and operating capacity ranges for the ESPs compared with traditional or conventional dewatering well pumps. This information helps to establish how ESPs provide certain functional and economic advantages over conventional pumps in a mine dewatering application. A schematic of a high-efficiency ESP in an oil and gas (O&G) application is shown in Fig. 1.

Sep 1, 2013

By C. Garcia, A. Potulska, J. J. Opazo, T. Comi

"The Sierra Gorda SCM sulfide ore processing plant began commissioning in the third quarter of 2014. Located in the Atacama Desert in northern Chile, the project is an open pit mine and Copper-Molybdenum processing plant is one of the most highly-instrumented operations in the world. It is the first hard rock operation in Chile and the second in South America to utilize HPGR technology. It is a significant Molybdenum resource especially in the first five years and the Molybdenum separation plant is complex. Designed to process up to 60 million lbs. of fine Molybdenum per year, it uses the latest technology and equipment to ensure superior recovery and product quality. It also has gas handling and alarm systems to fulfil the Company’s vision of “Zero Harm”. This paper discusses the overall operation and issues relating to the concentrator start-up. These include a review of the mineral processing design, the unified process control center and management information systems, and the correlation of geological and metallurgical performance data (mine-to-mill) for use in anticipating and preparing for treatment of diverse ore deliveries. INTRODUCTION Sierra Gorda SCM is a joint venture partnership with KGHM International (owned by KGHM SA, Poland), Sumitomo Metal Mining, and Sumitomo Corporation (Japan) operating in northern Chile. The Sierra Gorda open pit mine and Copper-Molybdenum processing plant will become one of the largest mines in the world. The need for optimum production efficiency and sustainability has driven the creation of the most modern, well-instrumented mine in Chile. This paper contains a general review of the project including geology and history. This was a very fast-track project going from greenfield site acquisition to mill start-up in 10 years. Highly-experienced and motivated engineers and technical staff have overcome many significant challenges resulting in a rapid ramp-up of production capacity. A potential expansion to double the production rate in the fourth year of operation has also been intensely studied. The Sierra Gorda property is located in the Atacama Desert of northern Chile, in the District of Sierra Gorda, Region II of Antofagasta, Chile (see Figure 1). There is almost no precipitation in this area. The mine site is generally flat with some rolling hills. The project is located about 5 km from the village of Sierra Gorda at an elevation of approximately 1,700 m above mean sea level. The village is near a highway and railway line. The city of Calama, home of the famous Chuquicamata Mine, is located about 60 km northeast of Sierra Gorda. In addition, the SG mine is in the midst of numerous other mines including Spence, Esperanza, Mantos Blancos, El Tesoro, Lomas Bayas, Gabriela Mistral, El Abra, Radomiro Tomic, and Escondida, to name a few."

Jan 1, 2015

By P. A. C. De Ruiter

The Lower Cretaceous salt deposits of the Gabon Basin and Congo Basin were said down on ton of an Burly Cretaceous Lato Jurassic, continental graben fill that represent!) the rifting phase of the Afro-American continent. The salt 13 characterized by high percentages of potash and magnesium salts and the scarcity of sulphates and carbonates. The salt probably originated from a brine that was already enriched in high-soluble salts before entering the Gabon Congo basins. Their low-solubility equivalents are found in the Cuanza Basin of Angola. Commercial mining of the potash salt is only possible in those onshore areas where it is essentially undisturbed, shallow and of the right chemical composition. These conditions are net in Congo where the Holle mine produces from rich sylvinite deposits.

Jan 1, 1978

By H. Saito

To Japan, which is scarce in natural resources, limestone is the only mineral resource comparatively rich in ore reserves and having broadly recognized outstanding quality. Distribution of the limestone deposits extends from Hokkaido in the north to Kyushu and Okinawa in the south, and the deposits are located in a manner of framework formation of the Islands of Japan. Studies of the geological ages of these ore deposits reveals that almost all of the main ore deposits west of Kanto Area belong to the Carboniferous Period - Permian Period of the Paleozoic Era. Also in the east of Kanto Area, deposits belonging to the Paleozoic Era constitute the main part, although recently there are increasing examples of reclassifying the geological age of the deposits heretofore considered as Paleozoic Era to the Triassic Period of the Mesozoic Era by the recent discoveries of the fossils of conodont, etc. Large ore deposits and main ore deposit groups are given in the Figure 1, which shows that the deposits are roughly found well distributed throughout the country.

Jan 1, 1982

By John Duff Erickson

Computer use has become an integral part of mine planning at Kennecott Copper Corporation?s Utah Copper Division, Bingham Canyon mine. Engineers are using the computer for development drilling calculations, mineralization grade interpolations, ore value summaries, long-range mining plans and short- range mining plans. The versatility of the computer has made it possible to explore many mining plan variations and to develop plans covering varying time intervals and production rates. This paper will summarize computer use in long-range mine planning, tell how short-range mining plans are prepared by conventional methods and discuss the development and application of short-range mine planning by computer.

Jan 1, 1966

By John T. Awald

The Bradshaw Mountains of west-central Arizona cover an area of 1600 square miles and contain numerous old mines and prospects. The area has been geochemically sampled on a reconnaissance basis to relate mineralized areas to regional structure and rock types. Copper analyses of stream sediments have been classified and contoured to show the distribution of low background, high background, and low, intermediate and highly anomalous areas. Contoured results are compared to geology and known mines. Several prospecting areas are indicated.

Jan 1, 1970