Search Documents

By William F. Abercrombie

The role of the laboratory is described in relation to the prospecting and exploration of kaolin clays. Test methods used to evaluate crude ore samples of kaolin clay for commercial consideration are reviewed. A background of the kaolin mineral and known means of prospecting this mineral are presented. Common analytical methods are discussed with special emphasis on those in use today.

Jan 1, 1982

By Poltak Sinaga

PT Kaltim Prima Coal?s 13.1 km overland conveyor (OLC) was commissioned in 1991. It is of conventional 3 roller 350 trough belt type. Cost and performance optimization during initial design ended up with 5.4 mps belt speed, 1000 mm belt width to convey 1350tph, and 7 mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30 mtpa (million ton per annum). Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4 200 tph satisfactorily.

Jan 1, 2008

By M. P. McArthur

General mining practices at W. R. Grace's Bonny Lake mine are much the same as those used in open pit phosphate mines in Central Florida, except for the difference in the depth of the overburden which introduces many variations, From 1945 to 1961 the mining at Bonny Lake has been from an area in which the overburden averages from 55 to 60 feet and in several locations exceeded 65 feet. The matrix thickness will average 15 to 18 feet for the areas mined. As you can see from the above depths a total hole depth will average from 70 to 75 feet.

Jan 1, 1962

By F. Nelson

RJB Mining is the largest coal producer in the UK. In January 1995 the Company acquired the Central North and Central South Regions of British Coal consisting of: ? 15 operating collieries -including capital equipment ? 2 care and maintenance mines ? 16 operating Opencast sites ? Interest in 26 prospective and 46 potential Opencast sites ? Approximately 417 million tonnes of proven and probable reserves and considerable mineral resource ? 9 million tonnes of coal stocks ? Long term contracts to supply approximately 90 million tonnes of coal to National Power and PowerGen to the period of 3 March 1998 ?Approximately 7,600 employees and 4,500 mining contractual labour. Up to the acquisition RJB Mining had the capacity to produce 14 million tonnes of saleable output with an approximate 1,500 strong workforce.

Jan 1, 1998

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After overall review of the flowsheet, two circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modelling system, and on this basis a quality assurance program for data gathering was implemented. A number of circuit design and operating variables were experimented with statistical analysis of plant test results revealed relationships previously unquantifiable by any other modelling technique. Improvements in classification system and mill grinding efficiencies were demonstrated and significant energy cost savings thus realized.

Jan 1, 1998

By Art Hamid, Manfred Wong, R. John Caulfield

"The proposed Channel Tunnel is a critical component of the San Francisco Public Utilities Commission’s (SFPUC) Central Bayside System Improvements Project (CBSIP), which is a key element of a $6.9-billion sewer system improvement program to upgrade its aging and seismically vulnerable wastewater facilities. The tunnel will provide gravity conveyance and storage of combined sewage flows from the northeast sector of San Francisco, CA to the Southeast Water Pollution Control Plant for treatment. The tunnel will be approximately 2.7 km (1.7 miles) long and 7.3 m (24 ft) in internal diameter. It will utilize a single-pass precast concrete segmental lining system. Tunneling challenges include excavating with pressurized face tunnel boring machine (TBM) technology through highly variable ground conditions including the Franciscan Complex (rock and mélange), clayey/silty sands, stiff to hard clay (Old Bay Clay) and mixed-face conditions. The project will also require several deep shafts that will be technically challenging. Project backgroundThe SFPUC is a department of the City and County of San Francisco, CA that provides municipal power, drinking water and wastewater services to San Francisco.San Francisco’s combined sewer system collects both wastewater and stormwater in the same sewers, which is then pumped, treated to stringent state standards and discharged into the San Francisco Bay and Pacific Ocean. The sewer system includes tunnels, large storage/transport boxes, 1,600 km (1,000 miles) of collection sewers, 28 pump stations and three wastewater treatment plants. After decades of service, much of the system is nearing the end of its useful life.The existing system is also vulnerable to seismic damage. During the 1989 Loma Prieta earthquake, damage to SFPUC wastewater infrastructure was extensive. This included the 3,415 m (11,200-ft) long, 1.7m (66-in.) diameter Channel Force Main, built in 1976, and a critical component of the conveyance system. The Channel Force Main carries 70 percent of the bayside dry weather sewage flow from the northern and central part of the city to the Southeast Water Pollution Control Plant for treatment. It is antiquated, not pile-supported and not constructed to current seismic codes. There is also currently no conveyance redundancy for north/central bayside flows to the treatment plant. Figure 1 shows the SFPUC’s wastewater collection system, the existing Channel Force Main and the project location."

Jan 5, 2017

By A. L. de Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS). Biologically produced hydrogen sulfide has economically very interesting application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By R. L. Grayson, S. S. Eslambolchi

"In making strategic economic decisions, it is important for a mining company to gain insights on the impact of significant political, social and economic issues when planning for present and future mines. The size of any mine, measured by the average number of employees working in the mine, will likely vary according to the pressures generated by the significant issues from one year to another. The objective of this study is to develop a model that represents U.S. underground coal mine size transitions during the period 2002-2012 using data derived from the MSHA databases. Coupled with information on significant issues over the past ten years, this model is used to gain insight on the impact of the issues on mine sizes. Results indicate that the structural impact of the combined driving pressures can be discerned by examining the year-to-year stability of mine-size categories. The effects of The MINER Act, the Obama Administration environmental policies on coal, and the coal market are evident. The lessons learned from these analyses give good insights on what the industry and market responses have been on the structure of the underground coal industry over the period of study. INTRODUCTION It is apparent that key driving issues affect the structure and viability of the coal industry. The driving issues may be political, social, and/or economic in the final analysis, but are generally rooted in reaction to dramatic and publicized events or movements. Mine disasters, an increase in miners’ disease prevalence, strife in the coal fields, and negative environmental impacts on air, land or water can capture the attention of the media and the public. Some of the issues occur over a long period of time, like the current global climate change movement. The coal industry veteran can sense the changes in political and social sentiment, and attempt to react to the economic repercussions; however, the insights from the media and from unique combinations of driving pressures are difficult to fathom. Thus decisions made on inadequate information related to the driving pressures and their likely impacts could lead to missteps in corporate and market restructuring. One way to gain some more insight on the potential impacts is to examine the complicated restructuring of mine operations in reaction to the driving pressures of the recent past. This paper examines an 11-year history of the changes in the underground coal industry structure, as reflected by changes in the numbers of mines in various statuses by mine-size categories. Superimposed on the results of mine-size changes is a mapping of the key driving pressures that occurred over the same period, 2002-2012. It is assumed that using this methodology, some important insights can be gained on the immediate and delayed responses to the driving pressures during that period."

Jan 1, 2015

By F. Ansheng

Though it becomes increasingly important with the valuable minerals in their deposits tending to be fine and poor, the solid and liquid separation remains difficult especially when the particles are of micrometer size and of low density. Almost of all conventional thickeners result in that fine particles lose into overflows which often costitutes a loss of potentially valuable resources as well as an environmental hazard. The addition of flocculations may improve the settling of solids but may also not work well for the final removal of fine particles from the overflows (Ref.1).

Jan 1, 1990

By H. EI-shall

In this paper, the results of bench scale testing of five different flotation processes to separate dolomite from phosphate are discussed. The effectiveness of each process interms of phosphate recovery and MgO content in the concentrate is used together with the reagent consumption as the basis of comparison. The water quality is found to play a major role in the performance of these processes. Effect of water hardness as well as other parameters are discussed.

Jan 1, 1995

By D. A. Fenton

The reliability of large diameter, high horsepower ball mill is paramount when large production and minimum downtime is required. The 17 ft. x 56 ft. double compartment ball mill at St. Lawrence Cement Company has the first gearless drive built in North America and has the world's largest hydrodynamic bearings currently built and running. The machine has seen three years operation and has met its specifications. The mill was designed by Aerofall Mills Limited and the gearless drive built and designed by the Canadian General Electric Company. This paper discusses the operation of the first North American installation of a gearless drive ball mill from the mechanical, electrical and process aspects.

Jan 1, 1977

By B. C. Litzinger

Minerações Brasileiras Reunidas S.A. - MBR is a brazilian iron ore mining company geared for the export market. It is controlled by Companhia Auxiliar de Empresas de Minerações - CAEMI through its subsidiary Empreendimentos Brasi leiros de Minerações - EBM which holds 51% in MBR and is formed by CAEMI, the six major japanese steelmills and five japanese trading companies, Universe Tankships, Inc., and Indústria e Comércio de Minérios S.A. - ICOMI. The remaining 49% of MBR's capital are held by St. John del Rey Mining Company, a subsidiary of The Hanna Mining Company. MBR iron ore reserves exceed 1.5 billion tons of high grade ore distributed in 36 deposits located in the so-called IRON QUADRANGLE in the State of Minas Gerais. The Aguas Claras Mine is the largest presently known and highest grade deposit owned by MBR. Other mines such as Pico, Mutuca and Jangada are in operation at a combined rate of production of about 2 to 2. 5 million tons per year. The project consists of mine, railroad and marine terminal (slide). The Aguas Claras deposit, which is located about six kilometers southeast of Belo Horizonte the Capital of Minas Gerais, was selected for initial development. The Sistema Regional Centro of the Rede Ferroviária Federal, through its 6th Division known as the "Central " is responsible for the transportation of MBR ore, and provided the necessary railway construction to connect Mine and Terminal. The Terminal is located on Guaiba Island near the entrance to Sepetiba Bay, at about 120 kilometers west of Rio de Janeiro.

Jan 1, 1974

By Christopher Mark

Area wide pillar failures, or “squeezes,” were once fairly common in underground coal mines. While rare today, they do occur. This paper describes seven case histories that were investigated by MSHA Technical Support. They occurred across the range of US coalfields, in both longwall and room-and-pillar mines, and involved development mining, pillar recovery, longwall panel extraction, and multiple seam interactions. Significant lessons from each are discussed.

Jun 25, 2024

By S. M. Khandrika

Most of the coal presently used by the utility industry is cleaned at preparation plants employing wet processes. While water is the mainstay of coal washing, it is one of the least desirable components in the final product causing a reduction of the heating value as well as handling difficulties. Currently available dewatering techniques are inefficient for dewatering very fine coal (minus 325 mesh). The US coal industry has expressed serious concern about utilizing advanced cleaning processes such as column flotation because an efficient and economical dewatering process is not available.

Jan 1, 1992

By Richard W. Patton

With the advent of the Clean Air Act and the installation of flue gas desulfurization (FGD) equipment (scrubbers) on coal fired power plants, the management of solid wastes has taken on added importance. Aside from the large amounts of fly ash and bottom ash usually generated, large quantities of liquids in the form of scrubber sludge are also produced. These wastes must be disposed of within the constraints of land and water quality regulations. This paper describes the practices adopted by the electric utility industry in denting with this problem, including methods of generation and treatment, quantities and characteristics of the materials, and transportation and disposal practices. The paper also briefly describes final product characteristics and several applications for commercial utilization and land reclamation.

Jan 1, 1983

By S. H. Seyedein, Hamed Tavakkoli, Mohammad Reza Aboutalebi, S. N. Asharafizadeh

The liquid–liquid extraction behavior of lutetium from different acidic solutions was investigated using two extractants, D2EHPA and PC88A, in kerosene. Lutetium extraction reactions with D2EHPA and PC88A from HNO3 and H2SO4 solutions were chemically and thermodynamically analyzed. It was found that each Lu cation was complexed with six monomers of the organic extractant and released three protons. Simultaneously, the Lu cation was instituted in the P–O–H group of the extractants. Thermodynamic analysis of reactions between extractants and acidic solutions showed that the D2EHPA-HNO3 system is the most favorable for extracting lutetium. It is noted that the calculated equilibrium constant of the reaction in this system was approximately six times larger than that of the D2EHPA-H2SO4 system. However, the value of the equilibrium constant for the D2EHPA-HNO3 system was evaluated to be approximately 200 times greater than that of the PC88A-HNO3 system. Therefore, one can conclude that the extraction behavior of lutetium is more influenced by the extractant type than the solutionmedium. The synergistic effect of different mixtures of extractants on the solvent extraction of lutetium was also examined, and the highest synergistic factor was obtained for a binary mixture of PC88A:D2EHPA at the ratio of 4:1 for both aqueous solutions.

Mar 15, 2021

By B. McNulty

The Niblack polymetallic volcanogenic massive sulfide deposits are located on Prince of Wales Island in southeast Alaska, approximately 50 km southwest of Ketchikan. The property hosts a number of polymetallic volcanogenic sulfide occurrences within the folded Lookout rhyolite volcanic succession. The Lookout deposit is the primary focus of current resource delineation and contains an indicated resource of 4,136,000 tonnes at 1.13% Cu, 2.32 g/t Au, 2.27% Zn, 38.70 g/t Ag and an inferred resource of 1,736,000 tonnes at 1.09% Cu, 1.77 g/t Au, 2.02% Zn, and 25.52 g/t Ag as of March 2011. Sulfide mineralization is interpreted to have formed sub-seafloor, within permeable felsic fragmental volcanic rocks. Sulfide minerals of economic interest include chalcopyrite and Fe-poor, Zn-rich sphalerite. Of considerable importance, the Lookout deposit contains elevated gold that occurs as inclusions within the base metal sulfides.

Jan 1, 2012

By A. T. Yu

As a nation, we have been known as perhaps the most wasteful in history. From the perspective of engineers and builders on the other hand, planned obsolescence and demolition did beneficially pave way for growth and provided environment for new businesses. Recent economic recession and intense competition from overseas, however, have drastically changed the economics. The high cost of capital and the demise of indiscriminate plant expansion have totally altered the way we conduct our business and run our operations. As a response to increasing demands for better efficiency with little or no funding available, everyone is forced to make do and do better with whatever little he has. Today it nay not be an exaggeration to state that modification of existing facilities may have finally emerged as a way of life. This paper will outline examples of how several companies have effectively modified existing facilities to do more and do it efficiently without having to demolish everything and/or to spend a fortune.

Jan 1, 1985

By Grant A. Brackebusch

Paste tailings disposal was successfully implemented at the New Jersey mill in Kellogg, ID with two different types of ore feed, a gold ore and a silver ore. The purpose of this paper is to describe the production of paste tailings, including operational problems during commissioning, and also highlight the environmental and economic benefits that were realized versus conventional tailings disposal such as the recycling of process water, increased shear strength and reduced permeability of the tailings mass, and reduced environmental permitting.

By E. A. Domínguez

La Espingarda kaolin deposit was formed by ?in situ? alteration of volcaniclastic rhyolitic rocks belonging to Jurassic Marifil Formation. Three volcanic lithofacies were identified: porphyric biotitic ignimbrites (PBI), a coarse lithic ignimbrite (ILG), a fluidal intrusive rhyolite (RFI), all kaolinized in different degrees. The alteration covers an ellipsoidal area of ~20,000 m2, with its alteration decreasing downwards and disappearing at 8-12 m from the surface. The length to thickness ratio of alteration is 60:1. An erratic silicification was found as small zones (<3 m2) of quartz stockwork. The mineralogy is kaolinite + quartz + feldspars + Fe-oxyhydroxides ± halloysite ± illite and interstratified I/S, although the relative proportions change in each rock type. Due to coarse grain size and high quartz content, natural kaolin is unsuitable for slip cast ceramics, unless beneficiated. Washed ILG kaolin has the best rheological properties and behavior in casting and drying for its mineralogy, particle size distribution, thin texture and surface activity, as well as a certain fusibility and firing kinetics. PBI and RFI kaolins, due to finer texture, smaller grain size, lower surface activity, and higher halloysite amount, have worse slip viscosity and thixotropy that are due also to soluble salts. For the same reason, they have good casting and drying properties, but their purity brings about higher softening temperatures and water absorption. Several parameters are used to discriminate between hypogene or supergene kaolinite genesis. The hydrothermal genesis is mainly sustained by fluid inclusion temperature (150-180ºC) in quartz veinlets, while weathering is supported by deposit morphology, simple mineralogy, kaolinite stable isotopes (d18O ? 18, 13; dD ? ?59; ?85) and paleoclimatic record. It is concluded that a weathering process formed the main alteration with some participation of steam-heated meteoric waters. Neither the contents of Au, Ag, As, Sb, Hg, nor drill data support the existence of any epithermal gold mineralization at the kaolinite bottom.

Jan 1, 2010