Search Documents

By Y. Pan, V. V. S. Vytla, P. Tukkaraja, R. BHARGAVA, S. Jayaraman Sridharan

Panel caving is an underground bulk mining method that utilizes gravitational force for mining massive, steeply dipping, and deep-seated ore deposits at a lower operating cost. To control dust and gas emissions entering the production level during the extraction of ore from the draw points in a panel cave, relatively negative pressure is created in the cave by installing an exhaust fan in the exhaust drift located on top of the cave. Since caving is a dynamic process, the design of an effective ventilation system is a challenging task, and therefore, estimation of airflow resistance offered by the broken rock inside the cave is critical. The complex and dynamic nature of caving also makes it difficult to predict the airflow resistance by using traditional approaches. This study investigates the effect of changes in the bulk porosity of the broken rock on the cave airflow resistance using computational fluid dynamics (CFD) approach. The results show an inverse relationship between the cave airflow resistance and the bulk cave porosity. The pressure-quantity characteristic curves presented in this paper provide valuable information for sizing and operating an exhaust fan used for a mature panel cave ventilation.

May 17, 2022

By D. Kwietnewski

The 4th bore of the Caldecott Tunnel is a 50-ft horseshoe shaped highway tunnel located in the hills east of Oakland, California. Tunnel excavation was mostly completed using one of the world?s largest commercially available roadheaders, a Wirth T3.20. The geologic profile included seven different geologic units, which displayed a range of different behavior with regard to excavation and initial support. Following a brief introduction to the excavation and support methods, this paper will discuss roadheader performance in the various geologic units encountered during excavation. Comments will also be made concerning the relationship between the roadheader method of excavation and observed ground convergence during excavation.

Feb 27, 2013

By R. F. Winkle

Shortly after World War II, considerable impetus was given to use of truck haulage in open pit mines by the manufacture of large off-highway trucks. Mine management was quick to utilize this more flexible approach to open pit operation and in the ensuing years much time and energy has been spent to improve the basic concept. Dramatic progress has been made in drilling, blasting, loading and hauling with much emphasis placed on equipment improvement. In general, haul roads in open pit mines and quarries have received rather perfunctory treatment in studies of surface mining operations. Their importance to the successful pit operation requires more than a brief sentence saying, "Good haul roads must be maintained." Haulage costs account for approximately one-third of total mining costs including general costs and about 90 percent of the total loading-haulage cycle time is consumed in travel, hence, good haul road planning, construction and maintenance are mandatory for a viable operation.

Jan 1, 1976

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By Milka Madahana, John Ekoru

For efficient management of operations, mining companies are required to be able to predict potential scenarios for main market factors. Competitive advantage and value creation are established through managing the value chain well. The mining value chain is usually faced with challenges from various shifts in commodity markets as well as ongoing uncertainties. Therefore, there is a need for accurate analysis of data from the markets, for the prediction of commodities, for instance, Precious Group Metals (PGM). The main objective of this research work is to apply machine learning methodologies with the aim to identify patterns and trends in the Precious Group Metals, and thereafter analyze and predict the future trends of these markets. Numerous machine learning models are applied to a dataset consisting of 15 years of daily price for eight precious metals namely Platinum, Palladium, Rhodium, Ruthenium, Osmium, Indium, Silver, and Gold. The results reveal the patterns and trends within the data sets and that different machine learning methods could be suited for the prediction of market prices for each of the PGMs. The application of an amalgamation of various machine learning methods may result in more accurate predictions of the PGM markets. Accurate prediction of market prices for PGMs will possibly result in unlocking untapped sources of value in the mining industry.

Jun 25, 2023

By Chaoxun Zhao, TAIYOU LI, JIAQI JIN, Jan D. Miller, Chen‑Luh Lin

A large portion of the energy consumed in copper concentrators is used to reduce the particle size of the feed by crushing and grinding. The cost of metal production could be reduced if low-grade particles of cm size were removed prior to further processing. Two copper sulfide ore samples (3 × 1 cm) from Arizona were analyzed by micro X-ray computed tomography (Micro-XCT) to determine the grade of copper sulfide in each particle. For copper ore sample A, a significant number of particles contained very low amounts of copper, while some particles had copper sulfide grains of mm size. Based on Micro-XCT, it was expected that 85% of the copper for sample A could be recovered at 65% of mass rejection during preconcentration by sorting. However, in sample B (a different copper ore), distribution of copper sulfide was dispersed primarily in each ore particle, so for the particle size class of 3 × 1 cm, liberation of copper sulfide and gangue minerals was not significant. In view of the XCT results, dual energy (DE) X-ray radiography was used as a basis for sorting. Previous DE X-ray radiography of a drill core sample demonstrated that this rapid detection method can be used to identify rich or poor Cu-bearing coarse particles. Pilot scale X-ray sorting of sample A (10 × 1 cm) showed 31% rejection of a 0.08% Cu gangue product with a corresponding recovery of 90% copper.

Nov 30, 2021

By J. S. Meyer

Although salmonid fishes (including Pacific salmon and trout) have only intermediate sensitivity to copper (Cu) for traditional toxicity endpoints (survival, growth, and reproduction) and thus do not ?drive? the freshwater Cu criteria (e.g., see species-sensitivity ranking in US EPA 2007), Cu concentrations as low as 1 to 2 µg/L have been reported to impair olfaction (the sense of smell) in salmonids in laboratory experiments using dilute fresh water (see references in Meyer and Adams 2010 and DeForest et al. 2011). Olfaction is crucial to predator avoidance, recognition of kin, and reproductive synchronization (Baldwin et al. 2003); and Cu is of general ecotoxicological concern because it can be present in acid/mine rock drainage, industrial and municipal effluents, agricultural runoff, and urban stormwater runoff (Meyer et al. 2007). Therefore, there is public concern that the current regulation of Cu in surface waters is not stringent enough to protect salmonid fishes against olfactory impairment (e.g., OSU 2007; Pearson 2007). Because the toxicity of metals to aquatic organisms is a function of water chemistry [e.g., acute toxicity of Cu generally decreases as pH, water hardness (Ca2+ + Mg2+), alkalinity, and dissolved organic carbon (DOC) concentrations increase; Meyer et al. 2007], hardness-based freshwater criteria for metals are lower at lower water hardness. The recently-developed biotic ligand model (BLM) explicitly takes into account all four of those water chemistry parameters and the concentrations of other major inorganic cations (Na+, K+) and anions (Cl-, SO42-) to predict the acute toxicity of cationic metals (e.g., Ag, Cd, Cu, Ni, Pb, Zn) to aquatic organisms; and the BLM has been adopted by the U.S. Environmental Protection Agency (US EPA) to calculate acute and chronic national freshwater criteria for Cu (US EPA 2007). Consistent with observations of Cu toxicity to aquatic organisms, BLM-based Cu criteria generally are lower at lower pH, water hardness, alkalinity, and DOC concentrations. Therefore, although threshold concentrations for olfactory impairment by Cu can be low in dilute fresh waters, the corresponding hardness-based and BLM-based Cu criteria for the same waters also tend to be low. This leads to a logical question: Are Cu criteria already protective against impairment of olfaction in salmonid fishes, thus obviating the need to decrease those criteria even lower to protect against adverse effects to this physiological/ecotoxicological endpoint? Herein, we demonstrate that in all studies conducted to date, the US EPA?s BLM-based freshwater Cu criteria would have been protective against olfactory impairment in salmonid fishes, but the US EPA?s hardness-based criteria would not always have been protective. This distinction is important because all 50 States in the USA still use hardness-based Cu criteria in their water quality standards, and only some of the States allow use of the BLM to calculate site-specific Cu criteria. Additionally, in the absence of empirical results for calibration of a saltwater Cu-olfactory model, we demonstrate that a proposed unified freshwater-saltwater Cu-olfactory BLM predicts the US EPA?s current saltwater Cu criteria would be protective against olfactory impairment caused by Cu in sea water.

Feb 27, 2013

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By H. E. Wyslouzil

The highly competitive nature of the international iron ore market has forced producers to improve the quality of their pellets. The demand for low acid pellets suitable for direct reduction has resulted in an increase in the number of plants utilizing reverse froth flotation for silica reduction. Column flotation is being favoured for this service due to the low capital and operating cost of the equipment, as well as improved metallurgical performance when compared to conventional flotation cells. This paper describes the benefits of column flotation and discusses some important aspects of circuit design.

Jan 1, 1993

By W. W. Wen

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen- bowl centrifuge for the dewatering and reconstitution of column flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine-clean-coal slurry from the column flotation concentrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free-flowing granular form, while the untreated products were wet, sticky, and difficult to handle. Specifically, test results indicated that the average moisture contents of the dewatered coal were 35.7, 35.5, 32.6, 29.9, and 26.5 wt% with Orimulsion additions of 0,0.7,3.2,4.8, and 6.4 wt%, respectively. The handleability and dust reduction of the dewatered coal product were also vastly improved.

Jan 1, 1997

By George Hufford

An investigation is made into the applicability of queueing theory to simulating the operation of a large open pit copper mine in the southwestern United States. Actual data from a working mine was used to construct curves for truck loading time, haulage and return time, and dumping times. Known results of investigations of queueing models (Koenigsberg - 1958, Gordon and Newell - 1967, Cabera and Maher - 1973) were used to simulate the actual operation. These did not give acceptable results so commonly used probability distributions were fitted to the actual data. A large computer program known as Q-GERT was used with the various parameters obtained from fitting the curves. Kolmogorov- Smirnov tests were run that showed that this was not satisfactory either. Finally, Q-GERT was used with the actual data from the mine. An appropriate correction factor is then found to apply to the exponential probability distributions tested previously and satisfactory results are obtained.

Jan 1, 1981

By D. R. Nagaraj

Depression of copper sulfides followed by MoS2 flotation is the most commonly practiced technique for Cu-MO separation. Although numerous organic depressants have been developed in the past, a majority of the currently used copper depressants are inorganic compounds (ex. NaHS, Nokes reagent, etc.). A unique advantage of organic depressants over the inorganic compounds is the potential versatility for design of the organic molecule to suit many requirements. The present study was initiated to systematically investigate the structure- activity relationships for a large number of organic complexing agents in comparison with the commonly used inorganic depressants that are often inefficient and hazardous. The results obtained in this study are discussed in light of the useful correlation obtained between practical solution redox potential and depressant activity. Several requirements, such as the presence of an active -SH and hydrophilic -OH or -COOH in the organic molecule, are identified for a reagent to be a satisfactory depressant. Some preliminary results on the desorbability (or destruction) of collector coating on the sulfide surfaces in the non-xanthate collector systems are also discussed.

Jan 1, 1983

By Yoginder P. Chugh

Most mines are large producing 0-25 mmt annually. The coal is mine.) at depths ranging from .0-150 m 120-500 ft mining at 300 m .(,1000 ft) depth is anticipated in the future. Single and multiple seams ranging from 3-12 m 10-40 ft) in thickness are mined. Most overburden is unconsolidated and consists of sands, and sandy or silty clays. The stripping ratio (volume of overburden to volume of coal mined) varies from 3-L. The overburden and coal is mined in benches 8-12 m -(24-40ft) high; the high-wall angle is about 45 degrees. Bucket wheel and bucket chain excavators are commonly utilized for overburden and coal removal, Some of the large overburden stripping machines nave capacities. Ranging from 4400-10,000 bank cu ( 6000-14,000 BC) per hour. The overburden from the upper benches is transported around the pit using the trains and belt conveyors. It is deposited in the spoils using large stacker-conveyor systems capable of handling 2550-7300 cu m/hour (7500-10,000 cu yds/hour). The overburden from the bottom two or three benches is transported across the pit using the conveyor bridges which are computer controlled. Conveyor bridges capable of handling overburden up to 60 m (200 ft) high are currently in use; a 60 a (20e ft) high conveyor bridge has a capacity of 85 x 10 cu ( 118 x 10 cu yd) annually. The coal is loaded in the trains directly and shipped to power plants or coke oven plants.

Jan 1, 1980

By L. D. Savage

Several experiments were conducted using a large crib fire adjacent to a Kennedy Metal Products steel stopping in a simulated cross cut to evaluate the proposed mechanisms by which a mine fire would breach the stopping. Temperatures in the convective air paths on both sides of the stopping, at the surface of the roof and 16mm within the roof were measured to evaluate the effects of heat transfer. The results indicate that roof failure is the prime method of breaching this design of stopping.

Jan 1, 1996

By Yanli Huang, Qiang Sun, Jixiong Zhang, Yuzhuo Jiang, Dan Ma

Mining accidents due to inrushing water are caused by sudden changes in seepage owing to structural damage to key strata of the aquiclude. The backfill mining method can be used to control the movement of the strata, weaken the evolution of fractures owing to damage by key aquiclude strata (KAS), and control the channel for inrushing water. This study develops a mechanical model of a composite beam on a non-uniform elastic foundation of the KAS by analyzing the coupling relationship between the filling body and the key water-resisting layer of the aquiclude. Equations of the deflection-induced deformation, bending moment, and maximum tensile stress of the KAS are analyzed, formulae to calculate the allowable tensile stress and backfill materials’ compaction ratio (BMCR) to ensure structural stability are derived, and are used to provide the critical BMCR for their structural instability. The results of field measurements show that the subsidence of the roof was 600–700 mm with an average BMCR of 80.63%. Damage to the overlying strata was controlled to ensure safe mining and the disposal of solid waste from the aquifer. The research here is useful for ensuring safety during mining while protecting water resources.

Jul 12, 2022

By Walter N. Campbell

The Simon Silver Mine is located near Mina, Nevada, approximately 50 miles northwest of Tonopah and 40 miles east of Hawthorne. It is an old property which was last worked in 1932 and closed operations due to problems arising from low metal prices. Federal Resources Corp. acquired the property in 1963 and undertook a completely new development program since the old surface plant and underground workings were beyond feasible repair. The deposit of silver, lead, zinc and copper is predominantly replacement of limestone. In the summer of 1964, a new surface plant was constructed and on December 2, 1964, sinking of a three compartment vertical shaft started and was completed to a depth of 1088 feet in April of 1965. Following the sinking program an 850 foot crosscut was driven to intersect the mineral zone on the 1000 level after which drifting, crosscutting and raising totaling some additional 4280 feet has been completed along with considerable diamond drilling and long holing into the walls. To date, two ore bodies have been encountered and test stoping operations are underway together with development of the 800 level for servicing, ventilation and access. The present development of ore is directed towards substantiating sufficient reserves to warrant the construction of a flotation mill.

Jan 1, 1967

By M. S. Moats, W. C. Hartzell

The stable domestic supply of gallium, indium, and germanium has been identified as a critical need for the United States. Electric arc furnace dusts, processed to recover zinc, produce a residue that could be a potential source of these critical materials. An industrial zinc leach residue was characterized to determine its particle size, chemical composition, and predominant mineral phases. Heated, atmospheric, agitated leaching using sulfuric acid and hydrochloric acid was examined to determine the extractions of gallium, indium, and germanium as a function of concentration and temperature. Extractions of gallium were found to be similar to iron in all experiments. The maximum percentage of Ga, Ge, and In leached into solution were 71%, 63%, and 48%, respectively.

Feb 1, 2023

By F. W. Schweitzer

The trend toward development of large low grade ore bodies has accelerated in recent years. It has been estimated within the copper industry that "porphyry" type deposits will provide the bulk of copper production during the next 30 years. It is further estimated that in these deposits the average ore grade by the year 2000 will be 0.25% copper (1). Many of the new porphyry copper discoveries are of such extremely low grade that they are particularly sensitive to small fluctuations in cost variables and copper prices. Because haulage constitutes a major item of surface mining expense, the capability to transport large tonnages of material at increasingly lower unit costs is vital to the profitable operation of many of these mines. High capacity conveyor belts appear to have considerable promise in this area. The heaviest use of high tonnage conveyors has been in the brown coal industry in Germany. In the past 20 years several such installations have proven successful. In addition to the German installations, several other successful systems have been put into operation. Some examples are: The Oroville Dam project in the United States; the tar sand operation in Northwest Canada; the pre-mine stripping and mining of the Twin Buttes Mine in the United States; the Kursk Magnetite 'dine in the U.S.S.R.; and the Nchanga Copper Mine in Zambia. Most of the systems mentioned are handling alluvial material consisting mainly of fines. The noteworthy point regarding these installations is their high continuous capacity. One of the largest lignite mines in the world is at Fortuna, Germany, where over 15,700 tons (15,250mt) per hour of overburden is transported on an 87 inch (221cm) wide belt running, at over 1000 feet (305m) per minute.(2). Another example is a 20,000 ton (18,150mt) per hour system for loading iron ore into barges on the Great Lakes (3).

Jan 1, 1976

By J. M. Pachter

Property sales and acquisition are prominent features of today's coal industry. Before selling or buying a site, a company must know the property's economic net worth. Any evaluation of economic net worth would be inadequate if determinations of a property's environmental liabilities and costs were omitted. Short-term and long-term costs can result from liabilities related to reclamation, water treatment, subsidence, and hazardous waste disposal. A structured, interdisciplinary approach can aid in the delineation, summation, and scheduling of these costs and liabilities.

Jan 1, 1986

By A. Leppala

Scope of the Courier 300 System The fact that reliable on-stream analysis is a prerequisite for effective flotation control is hardly disputed today. Nevertheless, up to now no system has been available that includes all the equipment necessary for successful analysis. However essential an on-stream analyser is in itself, reliable and accurate assaying can only be assured after techniques for sampling, handling the slurries and computing the X-ray data have been developed for the purpose. The Outokumpu Company's Courier 300 System is a complete package that can be installed and handed over with the key. It includes the equipment needed for sampling and handling the slurries. It has been developed from the start to meet industrial demands. Obviously an on-line system must comply with far stricter standards than one designed for a laboratory. Assays are computed by an Outokumpu 316 digital data processor, which is an integral part of the system and controls its entire performance. The computer software is programmed as a standard package, including a highly advanced new model for assay computation. Analysis output is available for a process computer, report typewriter:, and recorders. The package also includes calibration for slurry assays at our pilot installation before delivery. A complete Courier System can analyse up to 4Z slurries and six elements in each slurry. Thanks to its modular design, it can be dimensioned initially to the customer's requirements and is easy to expand later at low cost. Being a mining company itself, Outokumpu has been able to utilize its own long experience in non-ferrous metallurgy - an important factor contributing to the success of the Courier system. History of the project and present installations The first on-stream analyser was installed at Outokumpu'a Pyhasalmi Con¬centrator at the end of 1967, after several years' development. Since then,

Jan 1, 1971