Search Documents

By Peter Jackson

Over a quarter of a century ago a New Zealand physicist suggested the possibility of detecting coal seam discontinuities by a seismic method carried out underground in the mine workings (Evison 1955). Twenty years ago initial experiments were performed in Germany (Krey 1963). Since then research has continued, notably in Britain and Germany, in order to provide a reliable fault and washout detection system. The National Coal Board of Great Britain has now carried out more than 250 surveys in Britain, France and Australia. The first NCB survey in the U.S., a successful application of the technique to an Ohio coal seam, will be described and the strengths and limitations of the method explained.

Jan 1, 1984

By Rex T. Ellington

The fluidized bed is an effective method for investigating retorting phenomena and possibly a commercial means of retorting oil shale. Both were examined by Sinclair Oil Corp. (now part of Atlantic Richfield Co.) in the period 1.965 to 1968. The results of the work show that presence of an oxidizing environment during retorting results in loss of oil yield which indicates that vapor phase oil burns in preference to combustion of coke on spent shale. This has implications for several types of retorts. Correlation of the results of this work with that of other investigators shows that the partial pressure of retorting products in contact with oil shale during retorting has an effect on yield. Consideration of hardware indicates that there are several possibilities for commercial embodiment. As a companion to shaft-type retorts the fluidized bed could have good potential. Realistic assessment of costs suggests that further development may have to await commercialization of another process. The existence of a plant in which to test prototype size would markedly reduce such development costs. Results Preliminary development work with the apparatus was carried out using a fluidized bed of sand, as explained later, with the entire system brought up to temperature and flows stabilized. The shale was injected rapidly in a slug (batch) which had small mass compared to that of the high temperature system to make the reaction approach isothermality with reasonable approximation of instantaneous preheating. Typically, the temperature in the center of the bed dropped from 900°F to 600°F one minute after batch addition. It returned to 750' within three minutes and 900° within seven minutes. Obviously, the bed was quenched but it recovered rapidly. Average bed temperatures of 700' to 1020°F were examined to compare the effect of temperature with published results. Yields In the 700°F range were only 10 to 15%, of Fischer Assay (FA). Above about 950'F, oil yields decreased and gas yields increased. Nitrogen was used first as the fluidizing gas to provide a chemically inert medium. Incept for an insignificant dip at 895"F, Figure 1, oil yield was not affected by retorting temperature in the 800° to 900' range as long as residence time was adequate (16 minutes). At 925°F, the oil yield was some 103% FA. With further increase in temperature, the yield decreased to 86% FA at 1015°F. There is no increase in carbon on spent shale, the lost oil goes to Increased gas make.

Jan 1, 1972

By T. L. Myron

In recent years increasing attention has been given to improving both the chemical and physical properties of sinter. The first step toward this goal was the production of a self-fluxing-sinter. More recently, blast-furnace operators have found that significant improvements in blast-furnace performance can be achieved by improving and controlling the physical size of the sinter. The results of full-scale blast-furnace tests have shown that blast-furnace production can be improved by using a closely sized agglomerate. The improvements obtained by the use of pellets, a closely sized agglomerate, are well known. In contrast, blast furnaces charged with sinter having a wide size spectrum have generally not yielded results as satisfactory as those from furnaces 1) * charged with pellets. Beginning in 1958, Appleby-Frodingham charged plus 3/8-inch sinter to their blast furnaces. Further tests by other companies in Canada, 2) the United States, 3) and Australia showed that blast-furnace production could be improved by about one percent when the plus 3/8-inch material in the burden was increased by one percent. Because of the promising results obtained with screened sinter, an extensive test program was initiated to determine an effective means of producing sized sinter in U. S. Steel's sinter plants. This paper describes the work done by the Applied Research Laboratory in this program.

Jan 1, 1965

By W. R. Reed, W. J. Archer, A. B. Cecala, J. D. Potts

The U.S. National Institute for Occupational Safety and Health (NIOSH) uses light-scattering real-time dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer (i.e., with cyclone and pump configuration), was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

The Jiboia heavy mineral sands deposit is a new discovery associated with the São Francisco River delta on the northern coast of Sergipe state. The identified resources are part of the much larger mineralized trend. Mineralization is hosted in paleodunes deposited on Holocene marine terraces (Fig. 1). The dunes are up to 30 m above sea level, and mineralization occur from 6 m above sea level upward. The main ore minerals constitute pseudorutile, ilmenite, zircon, rutile and monazite. This work presents a thorough characterization of the mineralogy and granulometric distribution of the Jiboia orebody.

Apr 1, 2024

By R. Asamoah, P. Forson, W. Skinner, M. Zanin

Despite the seeming benefits decoupling pyrite and arsenopyrite minerals present in practice, little success has been achieved. The present study presents possible process routes for attaining selective flotation broadly capitalizing on differential oxidation between these minerals, and the use of a chelating collectors. The best performance was achieved with dithionocarbamate application following copper activation, yielding 81.4% arsenopyrite and 37% pyrite recovery. Preaeration followed by staged addition of xanthate produced 76% arsenopyrite and 31% pyrite recovery while reverse flotation of pyrite after H2O2 addition gave rise to rejection of 66% pyrite accompanied with 24% arsenopyrite.

Mar 2, 2022

By J. Killian, S. Cox

Many questions exist within the geotechnical industry as to the applicability of Strength Reduction Factor (SRF) values to the design acceptance criteria (DAC) of mining operations. There are many factors that contribute to changes in the SRF estimate, some of which are numerical (e.g. dilation angle) and some of which are geometric (e.g. model grid size)[1]. Numerous studies have confirmed equivalent values of SRF and FOS are found for soil slopes of limited height as presented in, [2] and [3]. However, significant deviation of the SRF value was observed for highly cohesive materials (rock slopes) of heights typically encountered in mining, [4]. This paper builds on the work presented in [4], providing a more rigorous examination of the modeling parameters that control the SRF estimate. The failure mechanism assumed for this study was a simple circular shear surface in a uniform material. Both LEM and numerical methods are suited well for analysis of this failure mechanism. A parametric study was completed to evaluate and test the relationships of key numerical variables that affect the estimated value of the SRF using Itasca’s Fast Lagrangian Analysis of Continua (FLACTM) software. The effect of groundwater has been tested and may be significant but is not presented as part of this body of work for brevity and simplicity of presentation.

Mar 2, 2022

By Andrew Kaczmarek

The mining industry is enjoying a much needed and long awaited increase in demand for natural resources. However, consolidations in the mining and mining service industries, along with a generational departure of experienced industry professionals, is challenging today’s mining companies. These challenges are not only in maintaining their existing operations, but also in securing qualified resources for developing new projects. These challenges are compounded for junior mining companies. They oftentimes lack for operating properties to draw experienced professionals from. Also, juniors have to compete with the majors’ “mega-projects” for experienced project personnel from the reduced ranks of engineering companies. This article discusses some strategies developed by Anatolia Minerals Development (Anatolia) in developing its Çöpler gold project in central Turkey.

Jan 1, 2006

Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design. The empirical methods are based on equations derived from large databases of various case studies. They are implemented in government-approved design tools and are widely used. There are also analytical and numerical techniques used for more detailed analysis of the induced loads. In this study, two different longwall mines with different panel width-to-depth ratios are analyzed using different methods. The empirical method used in the analysis is the square decay stress function that uses the abutment angle concept, implemented in pillar design software developed by the National Institute for Occupational Safety and Health (NIOSH). The first numerical method used in the analysis is a displacement-discontinuity (DD) variation of the boundaryelement method, LaModel, which utilizes the laminated overburden model (Heasley, 1998).

Jan 7, 2020

By H. Weber

This paper is in three parts. Part I discusses the various types of cement clinker coolers now in full-scale operation. Part II is a detailed study of the criteria for selection of the type of cement clinker cooler best suited for a given installation. Part III covers a number of cooling problems and their solutions in some of the metals industries. The large and world-wide problem of cement clinker cooling has motivated much study and development and the coverage here of this work is somewhat detailed. In contrast the cooling problems of the metals industries are quite varied between industries and often quite different from plant to plant in the same industry because of basic differences in the requirements of the particular material being processed. Therefore the coverage of metals industries coolers is somewhat more general. It is believed that all of the technology covered here may be of interest to those working with the problems of cooling hot materials.

Jan 1, 1980

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic metres per hour) for dozers operating in hard rock bulk push applications. The particle size distribution of the material employed in the test rig was modelled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. A commercially available road base material was found to be highly representative of site conditions. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard rock dozer push operations. Currently, it is difficult to estimate dozer push productivity in hard rock environments due to dozer productivity correction factors that are empirical in nature and provide only discrete, end-point values for a range of operating conditions. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 m to 40 m. As such, it is recommended that efficient bulk dozing operations in hard rock mining blocks should not exceed 40 m dozing distance. Further testing of muckpile conditions with increased clay and moisture content would be beneficial in order to better understand and quantify the effects of cohesion on hard rock dozer push productivity.

Nov 23, 2021

By J. C. Nigro

The potential use of prereduced pellets in the burden of the blast furnace continues to be a topic of interest. Several excellent papers have been written describing the theoretical and experimental rewards. (1) (2) (3) (4) (5) (6) (7) (8) (9) Significant increases in iron output and substantial savings in coke consumption are major advantages over conventional iron oxide pellets. The savings are especially important in areas where good coking coal is at a premium. Lower handling and transportation costs may also be factors favoring prereduction. When considering the overall cost of making and smelting prereduced materials the optimum metallization level becomes significant. An analysis by Agarwal and Pratt of the thermodynamic aspects of blast furnace operation with all prereduced pellets shows that the criteria controlling coke consumption depends upon the degree of reduction and upon the percentage of oxygen (present as FeO) removed by solution loss.(8) The authors state that although the chances of obtaining large fuel savings are greatly improved when metallization is high, reduction to the highest degree, which is costly, may not result in the lowest energy requirement per ton of hot metal; thus, over reduction could possibly result in wasted energy in the blast furnace.

Jan 1, 1968

By G. A. Irdi

An automated method of microscopy for determining the pyrite size distribution on two base coals that were crushed to 28 mesh x 0 has been developed. Polished epoxy-bound coal pellets were prepared and examined by a Zeiss IBAS image analyzer utilizing a program developed from provided software. Pyrite size distribution determination is considered a necessary first step in pyrite characterization that could lead to successful predictions, by microscopy, of a coal's theoretical pyritic sulfur removal. Our research efforts to date have indicated that the IBP-S can be a reliable instrument for determining pyrite size distribution in crushed coal. A program was also developed to convert pyrite size data to a weight basis for comparisons to the results from chemical analyses. The problems encountered in our research and their solutions will be presented in the discussion.

Jan 1, 1986

By Lewis V. Wade

This paper summarizes the results of the rock mechanics monitoring program performed as part of Old Ben Coal Company's longwall coal mining demonstration project conducted in cooperation with the United States Bureau of Mines. The work described herein included installation of instruments, collection of data and data analysis performed during mining of the first longwall panel in Mine No. 24. The rock mechanics monitoring program included both surface and underground instrumentation and was designed to achieve the following purposes: 1 -To provide the capability to observe unusual situations during mining so that remedial measures could be instituted quickly 2 -To formulate design guidelines for future longwall mining efforts; 3 -To evaluate surface subsidence, and its character, rate and potential effects on cultural features, and to develop criteria to assist in predicting subsidence for other mines having similar roof conditions. Six previous attempts with longwall methods in Old Ben Coal Company's Hine 21 had been unsuccessful due to roof control problems. A description of these attempts is given by Moroni (1973). In preparation for the present longwall operation a study was performed to review existing data on the previous unsuccessful attempts, to establish coa1-and floor-strata bearing capacities in Mines Nos. 21 and

Jan 1, 1977

By Burton H. Boyum

The paper generally reviews the iron ore occurrences and regional geology of Western Australia, but features in particular the mesa deposits of PJasic Materials - Cliffs International. Initial production is planned from a aeries of mesa deposits of Eocene-Oligocene age. The ore is oölitic to pisolitic goethite and hematite. Source of the iron in the mesa deposits is thought to be from the Precambrian iron-formations. The geology and occurrences of the mesa iron ore deposits are summarized and illustrated.

Jan 1, 1964

This paper presents the results of an investigation of the stability of the mass flow rates and average pellet size in the different streams of an industrial-scale balling circuit. The variables in this study include water content, drum speed and fresh feed rate. It was found that both the mass flow rates and pellet diameter are greatly disturbed when a change, positive or negative, in any of the variables takes place. For most of these disturbances to be damped don, a period of one hour or so is required. When a disturbance in the feed rate was made, the transient period extended to more than one and half hours (the duration of the experiment). It was observed that there is an interaction between the drum speed and moisture needed for producing an acceptable green ball product. The moisture content of the product pellets was found to be a function of the pellet size, with the larger pellets retaining a higher moisture content.

Jan 1, 1980

By J. J. Pavlica

Grinding in steel mills adversely affects the flotation removal of pyrrhotite from magnetite ores. To elucidate the effect of grinding media on the floatability of pyrrhotite, rest potential and short-circuit current measurements were made on electrode combinations of pyrrhotite-mild steel and pyrrhotite-stainless steel. Galvanic contact of pyrrhotite with mild steel increased the rate of surface reactions on pyrrhotite in air-exposed and oxygenated solutions. It was postulated that the formation of ' an iron hydroxide coating on the pyrrhotite adversely affected its floatability. Its formation was minimal when pyrrhotite was contacted with stainless steel. Fine magnetite particles caused slime coating on pyrrhotite surfaces by magnetic interaction and impaired the flotation of pyrrhotite.

Jan 1, 1982

By Yakup Cebeci, Leyla Kalender, Ceylan Yarluğkal Altınışık, Hikmet Sis

The abstract highlights the challenges in concentrating complex and non-sulfide lead-zinc ores and emphasizes the importance of froth flotation for their beneficiation. The study focuses on using process mineralogy to understand the flotation behavior of these ores from the Görgü region. The ore samples were characterized using various techniques, revealing oxidation and carbonation of primary minerals. The flotation results were interpreted in light of the mineralogical data, explaining the poor outcomes due to the complex nature of the ore, poor liberation, and lack of hydrophobicity.

Mar 22, 2022

By M. L. Wouden

The Bureau of Mines investigated pegmatite and granite formations at Copper Mountain, Fremont County, Wyoming, for recovery of tantalum and niobium. Sampling of surface exposures identified about 1.27 mega tonne of pegmatite resource material ranging between 0.02 and 0.04% Ta20, and 0.007% Hb20,. Beneficiation studies were conducted involving coarse-grained and fine grained pegmatite samples. Over 80% recovery of the coarse-grained tantalite was achieved in a concentrate averaging over 45% combined tantalum-niobium oxide. Lower concentrate grades and recoveries resulted from the treatment of fine-grained pegmatite.

Jan 1, 1991

By Ravi Shah, Augusto Lucarelli, Daniele Peila

"In mechanized tunneling the annular gap between the segmental lining and the surrounding soil caused by tunnel driving, must be backfilled almost instantaneously with an adequate grouting mortar. The objective of this research is to perform a fully three dimensional modeled parametric study using FLAC 3D and evaluate the effects of backfill grouting on the tunneling performance. The research focuses on comparisons between different injection materials and state-of-the-art Bi-Component grout and their effects on the settlements on the surface. The research consists of testing a regular situation of tunnel excavation using a shielded machine with face under pressure. The tunnel dimensions and the soil properties are selected as close as possible to the reality and based on Turin Metro case. 1 INTRODUCTION Excavation of tunnels in urban areas can induce ground movements, which have negative effects on existing structures. In such scenarios, shield tunneling has become a well-accepted construction method in various ground conditions. It is characterized by relatively complex interactions between the soil, the tunnel boring machine (TBM) itself, the tunnel lining and the tail void grout. The problem to control the settlement depends on the face pressure, ground properties and back filling procedure and material of the tail void. The face pressure acts against the front to guarantee the face stability. In case of EPB TBMs the stability of the tunnel face is ensured through the excavated soil itself, which is conditioned and is maintained in compressed state within the excavation chamber. When excavating with TBMs a tail void is created between ground and the lining (Fig.1) after the TBM excavation and ring assembly that must be backfilled instantaneously by injecting the backfill material through the TBM’s tail shield. The process is of primary importance as it reduces the surface settlements and creates an immediate link between the ground and lining, sealing against ground water and leakage, reducing the differential movements between segments and providing long-term stability. The most used backfilling materials are: Inert mixtures that do not contain cement instead sometimes they are replaced by fly ash or other substitutes. A typical design of an inert mortar consists of sand, fly ash, bentonite and water. Pea gravel, which is constituted of granular materials with grain size ranging from 8 to 12 mm. This mixture is highly recommended for tunnels being constructed in rock mass with little deformation rates.Cement mortar is composed of cement, water, aggregates and sometimes bentonite. Cement controls the principle mechanical property of the mix, which can reach high values of 15-20 MPa in 28 days. The aggregates contribute towards the shear strength and reduce the pumpablity of the mix (Thewes and Budach, 2009). The reduced active systems have a cement content of 50-100 kg/m3, whereas the active system the binder component derives full hydration with cement content of over 200 kg/m3 ."

Jan 1, 2016