Search Documents

By Dennis C. Martin

Assessment of the potential for mining induced subsidence and determination of ultimate design requirements for a mining operation should be based on a number of assessment approaches. Although the rock mechanics engineer has a variety of limit equilibrium and numerical modeling tools available for assessment and prediction of subsidence effects, empirical approaches based on precedent experience provide a powerful tool for calibration/verification of analytical models and prediction of subsidence. Three separate analyses approaches have been applied to the assessment of potential subsidence for a proposed block caving mine in eastern Canada. The investigations have included an assessment of documented historical information from previous block cave mining at the site, deterministic analyses using limit equilibrium approaches to assess kinematically possible failure mechanisms, and three-dimensional numerical modeling techniques. Analyses results have been used and compared with precedent experience and documentation of subsidence behavior from previous mining to optimize the subsidence predictions for the proposed mine.

Jan 1, 1998

By Scott Rosenthal, David Gilkey, Michael McGivern, Lorri Birkenbuel, Daniel Autenrieth, Ty Murphy, Hadi Aldossari

A safety climate case study was carried out at a surface metal mine where investigators administered the Liberty Mutual Short Scale Safety Climate Survey to 365–368 miners to measure safety climate in consecutive years. Following the baseline safety climate survey in 2019, Foundations for Safety Leadership (FSL) training was conducted with 81 middle to upper management employees at the mine site. Investigators found statistically significant differences in the pre vs. posttraining FSL assessment scores of the middle to upper management employees who attended the training. The follow-up safety climate evaluation was compared to baseline scores and revealed no significant improvement. The overall baseline company safety climate score of 76.38 increased minimally to 76.50 (p-value = 0.616). Investigators also evaluated differences in safety climate between the company’s three major divisions (operations, maintenance, and administration). Both years administration had the highest mean score and operations had the lowest mean score. The authors attributed the statistically significant differences found among the three major divisions to various dissimilarities in their work environments.

Aug 13, 2021

By F. F. Peng

Fine Coal Cleaning Processes including froth flotation, aggregative flotation or oil agglomeration, depend upon the wettability of coal particles in the aqueous solution. The wettability of coals of various ranks, hydrocarbon oil treated coals and oil-agglomerates have been measured using film flotation, induction timer, and froth flotation. Various hydrocarbon collector dispersion techniques are used to alter the surface wettability of coal particles. Change in wettability behaviors, measured by flotation responses, due to various ranks with or without of hydrocarbon collector modification are explained in terms of surface chemistry modifications as analyzed by induction time, film flotation as well as DRIFT Spectroscopy. The relationship between the wettability of coals and collector treated coals, and floatability are discussed.

Jan 1, 1993

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"During the last ten years great strides have been made, on the Mesabi Range, in the practice of beneficiating low grade iron ore material. By .beneficiation is meant all methods of removing impurities, and raising the iron content to a point where it can be sold in open market, the principal impurities being silica and moisture. The • general processes to which low grade iron ores are amenable are as follows:1. Thermal(a) Drying ; removes hydroscopic or atmospheric moisture. .(b) Calcining; removes carbon dioxide from iron carbonate, molecular water from hydrated hematites, and atmospheric moisture.Roasting; removes sulphur, carbon dioxide, molecular water and atmospheric moisture.Agglomeration; primarily for the purpose of preparing finely divided material for blast furnace; briquetting and sintering.2. MechanicalScreen sizing; removes rock and sand.Classification; removes sand by means of currents of water of varying velocities.Log washing; removes fine sand.Jigging; removes larger particles of impurities than is possible by log washing. Certain types of jigs remove fine sand.Reciprocating tables; recover fine iron particles from sand discarded by above processes.Magnetic separation; applicable to the commercial separation of the magnetic oxide of iron from gangue material. From a scientific standpoint it is possible to separate certain hematites and limonites from their gangue:(g) Miscellaneous processes; comprise dry concentration, electro-static separation and other processes."

Jan 1, 1920

By Paul E. Scheerer

Synthetically produced magnesium hydroxide serves as the precursor for much of the magnesium oxide produced in the world today. Magnesium oxide, in a variety of physical and chemically reactive forms, is a very important commodity. It is used as the main component in refractories employed in steelmaking furnaces and in many base metal refining furnaces. In the chemical industry, it serves as a raw material in the production of epsom salts, rayon acetate, oxychloride and oxysulfate cements and magnesium sulfonates. It is a minor component in fertilizers and animal feeds. It serves as the starting material for producing fused magnesia, used as an electrical insulator in electric heating elements. It is employed in the magnesium sulfite process for pulp digestion in the paper industry. Additional uses are in SO2 scrubbers, as a neutralizing agent in the tanning industry and as a component in rubber compounding. Magnesium oxide is produced not only from synthetically produced magnesium hydroxide. It is produced from natural magnesites, natural brucites, and natural and synthetic hydro-magnesites. Synthetic magnesium hydroxide, as a starting material provides more control of the chemical purity and chemical reactivity of resulting magnesium oxide products because of the uniform nature, chemical and physical, of the hydroxide that can be produced. Synthetic magnesium hydroxide is produced by precipitation of Mg (OH)2 from magnesium chloride bearing seawater or natural brines through the use of a base such as Ca(OH)2 or NaOH.

Jan 1, 1978

By D. R. Rathburn

Jan 1, 1962

By D. X. Tang, G. Wilson, S. S. Peng

Design and implementation of a roof bolting plan requires reliable geotechnical information of strata, such as rock strength, and locations of interfaces and voids/fractures. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way to gather information on the geological structure within the bolted horizon. The purpose of this research project is to develop a method for identifying the geological features in the mine roof strata based on drilling parameters of roof bolter. The criterion for void/fracture prediction has been developed and proven valid. This paper focuses on the estimation of the strength of roof strata by using drilling parameters. Based on the results of a series of underground and laboratory tests, feed pressure is found to be the most sensitive parameter when the strength of roof strata changes. Moreover, it was also found that both penetration rate and rotation rate have obvious impact on the magnitude of feed pressure. Based on these findings, the criterion for the estimation of roof strata strength has been developed using the relationship among feed pressure, penetration rate and rotation rate and implemented in MRGIS.

Jan 1, 2006

By G. Ofori-Sarpong, A. -S. Adam, R. K. Amankwah

"In the application of the BIOX® technology, high tailings grade (2-16 g/t) may be generated with a decrease in overall gold recovery, which sometimes make it economically unattractive. This paper investigated the causes of the high tailings grade by using samples from the Bogoso BIOX plant. Partial chemical analysis, diagnostic tests and cyanidation optimisation studies were conducted to invoke understanding into the high tailings grades. Diagnostic study on the tailings showed 48.34% of gold in carbonaceous matter, 17.12% in quartz, 13.40% as liberated gold, 11.51% imbedded in sulphides and the remaining 9.65% in carbonates. Optimum cyanidation recovery of 90.4% was established for the BIOX concentrate at 7 kg/t NaCN, 40-50 g/L activated carbon and residence time of 40 hours. The recovery was sensitive to carbon and cyanide concentrations but additional cyanide was not economical. High preg-robbing indices of 72.7% and 64.4% were recorded for the BIOX product and the flotation concentrate respectively. This confirms the inability of the BIOX process to deactivate carbonaceous matter, which remains a serious precursor for low overall gold recoveries and high CIL tailings. INTRODUCTION Gold ores may be broadly classified as refractory and non-refractory. Non-refractory ores are easy to treat but refractory materials require complicated flowsheets for metal extraction (Hausen and Bucknam, 1985; Schmitz et al, 2001; Marsden and House, 2006). As near surface non-refractory gold deposits are getting depleted, the increasing price of gold and increasing demand for gold, have encouraged many gold producing companies to treat refractory ores for gold recovery. The refractory behaviour of these ores may be due to the presence of sulphides, tellurides, cyanicides and/or carbonaceous matter. Refractory ores do not respond well to conventional cyanidation as the gold is either occluded by or in solid solution in sulphides, or is in association with cyanicides (Marsden and House, 2006). Further, carbonaceous matter preg-robs gold during leaching (Osseo-Asare et al, 1984; Hausen and Bucknam, 1985; Schmitz et al, 2001). The two major causes of refractoriness are the presence of sulphides and carbonaceous matter, and these render the ore double refractory (Nyavor and Egiebor, 1992). Oxidative pre-treatment processes such as high pressure leaching/oxidation; biological oxidation, ultra-fine grinding and roasting are required to render refractory ores amenable to conventional cyanidation (Marsden and House, 2006). Biological oxidation, however, has become the preferred pre-treatment route because it is more environmentally friendly and convenient even where only partial oxidation is required. Comparative tests have demonstrated that bioleaching can achieve the same or better results than roasting or pressure leaching in terms of gold recovery (Yannopoulos, 1991; Brierley, 1997). Further, biological treatment processes are more cost-effective, environmentally friendly and safer."

Jan 1, 2017

By William J. Shampine

This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map. This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map.

Jan 1, 1966

By Jey K. Jeyapalan

A characteristic common to most tailings dam failures caused by earthquakes or excessive rain storm is that the tailings tend to liquefy and flow for substantial distances as a viscous fluid, with the potential for extensive damage to property and life. Failures of El Cobre, Chile (1965), Mochikoshi, Japan (1978), Aberfan, Wales (19661, Buffalo Creek, West Virginia (1972) are examples of such catastrophic incidents. In these four incidents more than 400 lives were lost, and the loss of property was approximately $200 million. In order to be able to assess the potential for damage in case of such a failure, it is necessary to predict the possible extent of flow slide movement. This paper discusses simple procedures for performing such analyses. Also, in order to illustrate the use of these analysis procedures in tailings dam design, two case histories are analyzed.

Jan 1, 1982

By H. L. Lovall

Huge banks of preparation plant refuse and other non¬saleable materials have accumulated over the years in all major United States coal producing areas. These banks, esthetically and commercially undesirable, can cause air and water pollution and land reclamation and mineral conservation problems for the industry and nearby communities Although some refuse banks have been reworked to recover saleable coal, all remain and accumulation continues. Even those previously processed continue as potential hazards. Among the several problems created by refuse banks, in situ combustion is most treacherous. Of the millions of tons of major accumulations, there are at least 450 refuse banks on, fire at this time Attempts to extinguish such fires are costly, impractical and generally unfruitful. Studies are in progress to evaluate the potential of processing such materials to eliminate the combustion capability and to yield usable fuel and nonfuel products. Aspects of the study now in. development for coal refuse include: (a) evaluation of characteristics (size, sink-float, ash, sulfur and calorific value) of the coal refuse materials which are known to be highly variable, (b) development of an ignition test having significance for in situ conditions, (c) study of processing capabilities (comminution for liberation, pilot plant washing tests), and (d) investigation of potentially significant properties of fuel and nonfuel products which could be altered to enhance their market potential.. Among the latter products are lightweight aggregate, fill for mine slushing operations, construction, etc: Plans are to extend the studies to include the design, erection, and test processing of refuse with a transportable plant,; which could provide basic economic and product utilization data from several locations

Jan 1, 1964

By Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA's Laramie Energy Research Center at a site near Hanna, Wyoming, was completed on July 30, 1976. During the experiment production reached 0.32 Mm 3/d (12 Mft3/d) of 6.9 MJ/m3 gas (175 Btu/ft 3 ). Approximately 6100 tonne (6700 ton) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, cold gas - thermal efficiencies of 76 to 89 percent, and overall process efficiencies of 65 to 74 percent were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-1974.

Jan 1, 1977

By B. Valentim

Policies for reducing NOx emissions have led power plants to restrict O2, resulting in high-carbon fly ash production. Therefore, some potentially useful fly ash, such as the economizer fly ash, is discarded without a thorough knowledge of its composition. In order to characterize this type of fly ash, samples were collected from the economizer of a Portuguese power plant burning two low-sulfur bituminous coals. Characterization was also performed on economizer fly ash subsamples after wet sieving, density and magnetic separation. Analysis included atomic absorption spectroscopy, loss-on-ignition, scanning electron microscopy/energy-dispersive X-ray spectroscopy, optical microscopy, and micro-Raman spectroscopy. Key words: Fly ash; Petrology; Petrography; Economizer fly ash

Jan 1, 2009

By L. D. Cruz

In Exxon's Los Bronces Expansion Project in Chile, a stochastic simulation is performed to resolve the complex decision problem of matching the mine to mill system capacities from both technical and economic standpoints. The unique combination of weather conditions at the mine and the 30-km belt conveyor network for ore transport to the mill necessitates this analysis in the planning phase to optimize the design capacity of the sys tem. Appropriate statistical distributions of major equipment performance, snow storm duration, power outage, etc, ate developed from actual mine local records and manufacturers specifications. The interactions of operational constraints including ore storage capacities, number and sizes of individual equipment, ore variations, and mine and mill production rates are studied more realistically than in a traditional planning approach. Details of the computer modeling and typical results of simulation studies are discussed.

Jan 1, 1981

By T. Hayashi

A sophisticated process of extracting ultrafine sulfide mineral particles of under 1µm size suspended in clay slurry has been developed through studies of electrochemical properties of particle surface. Experimental procedure and data of the process applied to some clay ores containing sphalerite and pyrite, and molybdenite and other sulfide minerals are reported. Discussions concentrated on the function of process reagents, particularly on various modifying reagents, and on the effect of dispersed or flocculated state of ultrafine particles in slurry which affect significantly the performance of the process.

Jan 1, 1982

By Douglas W. Fuerstenau, Pradip Pradip

The design and development of selective flotation collectors has been the key to the remarkable success of flotation in beneficiating complex, difficult-to-process ores. Sustained research efforts in the field over the past hundred years have led to delineating the scientific basis of selective mineral flotation in terms of the crystal chemistry and the surface and colloid chemistry of minerals including their solubility, and the aqueous solution chemistry of added reagents. It is now well-established that the electrical double layer theory (EDL) is the most powerful means of quantifying the relative strength of mineral-reagent interactions in the case of nonsulfide minerals. We illustrate the utility and the power of the EDL in delineating the science underlying selective mineral flotation with the help of a few examples taken from our own work, in particular on the selective flotation of rare-earth minerals (bastnaesite) from associated semisoluble minerals (barite and calcite) using alkyl hydroxamate collectors and the flotation separation of lithium-containing minerals (spodumene) from associated alumino-silicate minerals with oleate (fatty acids). Both of these mineral separation systems are of contemporary research interest and of immense value to the industry today. Recent advances in utilizing molecular modeling computations, particularly in the context of quantifying the effect of crystal chemistry and the relative distribution of adsorption sites available on mineral cleavage planes, are also reviewed.

By Pablo Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occuring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, California recovers potash from natural brines, but uses fuel to accomplish evaporation. Under proper meteorological conditions the use of solar evaporation might be desirable from the economical standpoint. Of course, this may not be true when, if by artificial evaporation, a group of very valuable salts are recovered. This is the case of the American Potash operation at Trona. Solar evaporation has its limits. The working temperature is low. We may say, just to cover most areas of the world where solar evaporation may be practical, that it will take place between 18°C and perhaps around 45°C. In most cases the average working temperature expected will be around 25°C.

Jan 1, 1963

By Ben E. Adams

The Duval Corporation Sierrita copper and molybdenum mining complex is located approximately twenty-three miles south of Tucson, Arizona. The original open pit mine, Esperanza, was put into operation in 1958 and utilized one tailings dam until the Sierrita operation began in 1970, and a second pond was started. Both tailings operations continued to be operated separate and independently of each other until 1977, when the Esperanza Mill was temporarily shut down, and the Esperanza Tailings Dam was retired from service. Except for short periods of use, no new tailings were put on the surface. With the reactivation of the Esperanza Mill in 1979, the Esperanza tailings were combined with the Sierrita Mill tailings and put on the Sierrita Dam, leaving the Esperanza Dam in a retired state.

Jan 1, 1984

By RIINA SALMIMIES, ANTTI HAKKINEN, PAULA VEHMAANPERA

Better understanding of the mechanisms and kinetics of dissolution can benefit several industrial processes. For example, iron can be leached from clays, which can be further used as a raw material in the ceramic industry. Another important application is the regeneration of ceramic filter media, which are used in the dewatering of iron ores. Dissolution of iron oxides in mixtures of acids is fairly uncommon and a less well-understood phenomenon, but it can result in a more efficient process. This work also shows that the determination of dissolution mechanisms and kinetics is not straightforward in different acid systems.

By M. Javier

Mining is an industry of experimentation throughout human history. Recently, societies are giving a clear message about mining because many projects are being rejected around the world. These refusals are a generational reaction to the activity of mining. In practice, it generates the perception that mining is using the same methodology without attending to the gradual initiation of conflicts. This is in spite of the best engineering and technology of the time that are put in place at the presentation of those mining projects. Some of these rejected projects are geographically distant from each other, but the communities? rejection occurred during many cases under similar characteristics. This concern shows that the current model of mining projects needs to be replaced with a new one: A new Design, one within which the socio-environmental values of this millennium are inherent. This paper describes Mining Project 101 to help the industry to set the highest and cleanest standards for mining. It also presents its aspects to sustainability and nature, which provides the principles and procedures for designing, planning, and operating mining projects with sensitivity to nature. It offers methods of diagnostic, remediation, and extraction while at the same time preventing and preserving a physical, chemical, and biological equilibrium of nature. This emerging process will be a step up from having a mining industry unaccountable to the socio-environmental conflicts it perpetrates and will abandon the ?cosmetic? repair on the caducity of traditional models in today?s practice. In conclusion, we have the opportunity to change this model. KEYWORDS: Equilibrium in Nature, Geomímic, Deproduction, mine design.

Feb 27, 2013