Search Documents

By D. F. Malan, P. J. Le Roux

Almost no work has been published on the strength of pillars in mines exploiting the LG6/LG6A chromitite bands in the Western Bushveld Complex. The strength of these pillars is unknown, and the hard rock industry still uses the Hedley and Grant formula. Numerical modelling, using inelastic constitutive models, may be of some value in estimating the pillar strength, but this approach is difficult and prone to errors as many assumptions are made. This paper explores the alternative approach of the back-analysis of actual LG6/LG6A mining layouts, using displacement discontinuity codes to simulate the average pillar stresses on a mine-wide scale. From this, and underground observations, a ‘minimum’ pillar strength (K-value in the pillar strength formula) can be estimated. The codes TEXAN and Map3D are both used in the paper to simulate the actual pillar shapes and sizes in an LG6/LG6A mine. The results are encouraging as the two codes produced similar APS values for a complex pillar geometry. An estimated K-value of 77 MPa was determined for the LG6/LG6A pillars in this particular area. This is more or less similar to earlier work done for the UG2 chromitite seam, but higher than the K-value of 39 MPa for a linear formula obtained by other workers for LG6/LG6A pillars. Caution should therefore be exercised before using this higher value for all areas. The effect of element sizes and explicitly simulating the effect of the surface for shallow pillars is illustrated in the manuscript using both codes. The need for actual pillar observations and an iterative design process, which cycles between modelling and observations, is also emphasized.

Nov 27, 2024

By B. P. Watson

Uniaxial tests performed on core from instrumented sites at Amandelbult 1 shaft, Impala 10 shaft and Union Section Spud shaft showed a nonlinear elastic relationship between applied load and induced deformation. This nonlinear behaviour does not appear to be dependent on borehole orientation but in the case of the Amandelbult and Union sites appears to have been influenced by the stress condition of the rock mass at the time of drilling. Cores drilled at these two sites under destressed conditions, such as over a stope, showed a linear elastic response to the applied load whereas most of the cores drilled under relatively high radial stresses were nonlinear. The Impala 10 shaft tests, however, all showed strong nonlinear behaviour irrespective of the stress condition of the rock mass at the time of drilling, although high stress conditions may have influenced the severity of the nonlinearity. A comparison between underground stress change measurements and an elastic model indicated that the rock mass became nonlinear when the virgin stress condition was relaxed to about 10 MPa. The cores for laboratory testing were retrieved from vertical boreholes drilled up from the centre of a stope and from horizontal boreholes drilled over pillars and stopes at about 600 m, 1 100 m and 1 400 m below surface for the three sites respectively. The k-ratios under virgin conditions were estimated from sockets, modelling and stress measurements to be 1.0, 1.3, and 0.5 for the Amandelbult, Impala and Union sites respectively. Of the three sites, therefore, Impala 10 shaft appears to have had the highest virgin stress state. Tests performed on similar rocks from shallower depths at Impala Platinum essentially showed a linear relationship between stress and strain. From the small Impala Platinum rock test database available to the project, it appears that the nonlinear elastic behaviour initiates at this mine from about 1 000 m below surface and seems to become progressively more nonlinear below this depth. In addition, the nonlinear elastic rocks are weaker, have a lower Young?s modulus and a higher Poisson?s ratio than their linear elastic equivalents. Interestingly the tangential Poisson?s ratios of the nonlinear elastic materials are often greater than 0.5 at 50% of the failure stress, suggesting an early failure initiation. The paper describes the microscope and modelling work done to determine the causes of the nonlinear behaviour and discusses some implications of the behaviour for deep-level mining.

Jan 1, 2009

By I. E. Teymenson, L. A. Bakhvalov

Irrational usage of mineral commodities leads to depletion of natural resources and various ecological violations in natural environment. Fulfilment of a number of measures and strategic decisions by given problems requires a correct forecast of trends of social-economic systems. For solving the task of long-term forecasting special procedures, considering Kondratyev’s big cycles of world conjuncture, have been embedded into algorithms of unknown parameters identification and recovering of factors of different countries mineral resources production and consumption models. In the paper the classification of long cycles types, existing forecasting algorithms on the basis of Kondratyev’s ‘long waves’ or ‘K-waves’ and the modified algorithm, developed by us, which allows to reduce time and financial expenses and to improve the forecast quality, are presented. Furthermore, the article includes several forecasts of mining branch corrected models factors, received by us, permitting complex prognosis of economic and social development of different scale and control level systems. In the paper workability of proposed forecasting algorithms on the base of ‘K-waves’ and adequacy of created models to researched processes are proved.

Jan 1, 2003

By Wilson. D.

The Vaal Triangle Branch of The South African Institute of Mining and Metallurgy was established on 20th November, 1986, at a meeting enthusiastically supported by local members. In attendance were special guests Dr H. Wagner (President, SAIMM) and Dr O.K. H. Stefen (Junior Vice-President, SAIMM).

Jan 1, 1987

By A. R. Javadi

Pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite (ZnS) and galena (PbS) generate hydrogen peroxide (H2O2) when placed in water, with pyrite generating the most amount of H2O2. The order of these minerals for generating H2O2 in water is: pyrite > chalcopyrite > sphalerite > galena. In previous research, the methods of generation of H2O2 in the grinding mill were studied. In this study, data from experiments were included by using MODDE 9 software for six parameters composed of water, grinding media, particle size; adding collector to the grinding, and adding depressant and pH. Finally the optimal condition was achieved. According to the results, most of the recovery is related to the particle 75 μ size and when using processed water, adding 100% collector and without depressant and pH 10. The most recovery of lead in the case of the use of fresh water is in the case of 100% collector, without depressant, pH 10 and 150 μ particle size. Maximum recovery in fraction size 45 μ in the case of water process is 100% collector, without depressant and pH 10. Maximum depressant of pyrite will be the fraction size 75 μ, distilled water, without collector, 100 depressant. Keywords: Sulfide mineral, hydrogen peroxide, flotation, oxidation

Jan 1, 2020

By J .. F. Brownrigg

In the mining method used at O'Okiep Copper Company (OCC), vertical crater retreat, the prime requirement for the fill is that it should be sufficiently strong to be free-standing to a height of 150 m. Other requirements are minimal decant and drainage water, and high pulp density to allow large tonnages to be placed quickly and alleviate transport problems. The excessively high cost of cement precluded the use of a cement-based fill, and after three years of extensive investigations a backfill based on the smelter slag was produced. Currently a fill with a uniaxial compressive strength of greater than 1 000 kPa after one month is being produced. This is in excess of the design specification of 850 kPa after 2 - 3 months. The research and development which went into the slagfill is briefly covered; the production of the fill from the various raw materials is described; and the design and control systems of the backfill plant, the reticulation system and its monitoring are examined. Finally, the implications of this high- quality fill for the mining programme are assessed.

Jan 1, 1988

By M. Kerr

Background- History The most significant change in mining since the late 1970?s has been the emergence of very large scale mining operations , which have been developed to ensure profitability with relatively low grade ores. These large tonnage operations have resulted in the development of larger unit sized machines in all operations of beneficiation, solid-liquid separation and dewatering. Often only a few flotation lines are installed and tonnages up to 25 ktpd and beyond are not uncommon. The increased throughputs have led to the development of circular, reactor type tank designs. The reactor cell system is the most up to date flotation cell design to utilise the principles of circular cell design. The Svedala DV mechanism was specially developed to suit the RCS machine giving good solids handling characteristics and excellent metallurgical performance. Development of UG2 ore type flotation equipment The equipment was developed and optimised by Svedala process from 1995. A higher energy specification was requested by industry. This amounted to 3kW/m3 for installed volume. Existing designs were at 1.5kW/m3. Hence various modifications were required to achieve the required power input. The first 50m3 machines were installed and developed at Impala Platinum?s UG2 circuit over a one year period. Once reliability and performance was achieved, over 300 large volume flotation cells were installed at Anglo Platinum and Lonmin operations as well. Pilot Plant Development The Impala Platinum High Energy pilot plant was commissioned in 2002 and had an installed power exceeding 5kW/m3. It was operated for over a year at the tailings dam booster station and was fundamental to the large scale scavenging plant design. All experience in overcoming mechanical and operational problems was applied in scale up design principles. A very robust mechanism was designed to accommodate the additional power input from installed motors, as well as the high SG (>1.5) of the feed source. The pilot plant flowsheet is shown in the figure below.

Jan 1, 2007

The aim of this investigation was to study the influence that varying production rates have on iron sinter quality. This was done by performing sinter pot tests at different pressure drops over the sinter bed, namely 11 kPa and 15 kPa (for 500 mm total bed depths). During each of the sintering processes temperature-time profiles were recorded of the top, middle and bottom layers of the sinter bed. On completion of the sinter process the sinter cakes were divided into top, middle and bottom layers. The physical properties of each layer were subsequently characterized by performing a tumbler test and a sieve analysis. A comprehensive mineralogical study was also conducted on each layer. This study revealed that sinters of similar cold strength could be produced under the examined production rates. However, a higher production rate was accompanied by an increased amount of fines. The cold strengths of both sinters significantly increased from the top layer to the bottom layer of the sinter bed. This strength variation is not related in any simple way to the phase composition. Keywords: Sinter, sinter bed, production rate, phase composition, cold strength, tumbler index, sieve analysis, temperature-time profile

Jan 1, 2003

By R. M. Lamya

The kinetics of copper cementation during atmosphere leaching of a Ni-Cu matte in CuSO4-H2SO4 solution was studied as a function of initial copper ion concentration, initial acid concentration, temperature, stirring rate, particle size distribution and pulp density. It was found that all these process variables influenced the rate of cementation. A two-stage rate of reaction was observed inmost of the experiments, with the rate of cementation in the initial stage being slower than that of the subsequent second stage. The increased rate of cementation in the second stage was attributed to the enhancing effect of the surface deposit. The cementation process was found to take place by two different rate-controlling mechanisms. At a temperature range of 50?70°C, an activation energy of 74.6 kJ/mol was obtained, indicating a surface reaction controlled process. At higher temperatures (70?80°C) a lower value of activation energy was observed (18.2 kJ/mol), indicative of a process controlled by diffusion through surface layers. The structural characteristics of the cemented deposit could not be determined in the investigated system where the deposit was mixed with the leach solid residue.

Jan 1, 2005

Council for 1999/2000 President J.R. Dixon President Elect M.H. Rogers Vice Presidents Senior Dr L.A. Cramer Junior A.A.B. Douglas Immediate Past President R.P. Mohring Honorary Treasurer J.A. Cruise Members of Council B.C. Alberts Dr N.A. Barcza N.J. Barkhuysen R.D. Beck M.J.P. Bierman Prof. A.N. Brown D. Cockcroft Dr M.B. Cortie Dr L.A. Cramer J.A. Cruise E.G. de Villiers J.R. Dixon A.A.B. Douglas F.M.G. Egerton J.P.W. Fisher C.E. Fivaz K.J.R. Ford Prof. G.A. Fourie R. Graham Dr R.G. Gürtunca Dr R.V.R. Handfield-Jones* M.C. Harris J.P. Hoffman H.E. James P.J. Knottenbelt R.P. Mohring H.G. Mosenthal G.Y. Nisbet N.M. O'Brien R.G.B. Pickering Prof. R.P. Plewman S.J. Ramokgopa Prof. R.E. Robinson M.H. Rogers D.A.J. Ross-Watt Prof. R.F. Sandenbergh Dr H. Scott-Russell C.B. Sheppard D.A.A. Smith Dr T.R. Stacey Dr O.K.H. Steffen D.J. van Niekerk J.C. Viljoen J.N. Wallington

Jan 1, 1999

Application of Gy?s formula is appropriate for calculation of the Fundamental Error (FE) prior to samples being collected at any stage of the minerals process, provided that sampling parameters K and a (alpha) have been determined by calibration of the ores. Two types of calibration procedure are well established in the industry, the Hetrogeneity test and the 32-piece sampling tree experiment. The sampling tree experiment uses the variance and average grade of metal analyses from four series of samples at different nominal fragment size, as the basic input data. Pierre Gy suggested the cube as an appropriate exponent of the nominal fragment size for use in his equation. More recent work suggests that this exponent is variable and characteristic of specific ores and therefore requires calibration. The method described here explains the experimental procedure of the calibration. It is then possible to calculate a sampling nomogram using the sampling parameters K and a. This allows the sampler to determine a suitable protocol for the sampling event that will ensure that the FE does not exceed a predetermined precision at any point in the sampling procedure.

Jan 1, 2007

By L. G. Austin

The paper summarizes the current state of development of simulation models for SAG and FAG mills, and gives the results of recent investigations of the physical processes occurring in autogenous grinding. The breakage process is treated as the sum of three regions of breakage actions: normal breakage caused by nipping of particles between media (steel balls or pebbles); abnormal breakage caused by media when the particle or lump is too big in relation to the media to be readily nipped; and self-breakage resulting from the chip¬ping fracture and abrasion of the tumbling action of rock lumps. Each region of breakage action has associated specific rates of breakage and primary progeny fragment distributions. A simplified form of the model was used to predict the performance of an 8 m diameter SAG mill with L/D = 0.5 grinding a copper ore, and predicted maximum capacity and minimum kWh/ton at about 6% ball load at 25% total filling. Two FAG mills of L/D = 2 were necessary to give the same capacity, and the simulations indicated a lower kWh/ton for these mills. For this ore, both systems were technically feasible.

Jan 1, 1987

The wage structure of graduate White men in 1979, by Adri Kruger, Pretoria, Human Sciences Research Council, 1979.76 pp. R5,00. (Reviewer: D. G. Malan) Financial Times mining international yearbook, edited by WilIiam G. Nightingale. London, Longman, 1980. 750 pp. £24 by surface, £34 by air. (Reviewer: J. D. Austin) Techniques in mineral exploration, by J. H. Reedman. Barking (U.K.), Applied Science Publishers, 1979. 533 pp. $90. (Reviewer: D. L. Kyle) Practical geostatistics, by Isobel Clark. Barking (U.K.), Applied Science Publishers, 1979. 129 pp. £13,75. (Reviewer: D. G. Krige) Uranium: The balance of supply and demand 1978- 1990, by the Uranium Institute. London, Mining Journal Books, 1979. 61 pp. £8,50 by surface,,£9,25 by airmail. (Reviewer: D. J. Crowe) Wear and abrasion in industry The South African Institute of Mining and Metallurgy and the Institution of Metallurgists (South African Branch) is to hold a colloquium on the topic of wear and abrasion of metals in February 1981. Steel rolling The International Conference on Steel Rolling sponsored by The Iron and Steel Institute of Japan will be held in Tokyo, Japan, from 29th September to 4th October, 1980.

Jan 1, 1980

1. Book review Technology of metal powders- recent developments, edited by L. H. Yaverbaum. New Jersey, Noyes Data Corporation, 1980. 400 pp. (Reviewer: B. K. Loveday) 2. New books The use of microprocessors, by M. Aumiaux. New York, Wiley, 1980. 176 pp. $25,50. Aluminium smelter technology, a pure and applied approach, by K. Grojtheim and B. J. Welch. Diisseldorf, Aluminium-Verlag GmbH (P.O. Box 1207, D-4000, Federal Republic of Germany). 146 pp. DM48. Coal-bridge to the future. New York, Harper & Row, 1980. $35. System modeling and response.. theoretical and experimental approaches, by O. Doebelin. New York, Wiley, 1980. 576 pp. $26. Environmental and climatic impact of coal utilization, edited by J. J. Singh and A. Deepak. New York, Academic Press, 1980. 646 pp. $39,50. Proceedings of the Third European Conference on Mixing, York, England, April 1979, edited by H. S. Stephens and C. A. Stapleton. BHRA Fluid Engineering (Cranfield, Bedford Mk43 OAJ, U.K.), 1980. 2 volumes. 500 pp. $50. Lignite technology, edited by P. Nowacki. New Jersey, Noyes Data Corporation, 1980. 228 pp. $42. The application of rock mechanics to cut-and jill mining. London, Institution of Mining and Metallurgy, 1980. Papers presented at the Fifth International Symposium on Jet Cutting Technology, Hanover, Federal Republic of Germany, June 1980, edited by H. S. Stephens and B. Jawis. BHRA Fluid Engineering (Cranfield, Bedford Mk 43 OAJ, U.K.), 1980. 438 pp. £38. World coal resources.. methods of assessment and results, by G. Fettweis. Amsterdam, Elsevier, 1979. 425 pp. $80,50. Geophysical and geochemical techniques for exploration of hydrocarbons and minerals, edited by M. Sittig. New Jersey, Noyes Data Corporation, 1980. 300 pp. $40. Financial Times mining international year book 1980. Longman Group Ltd (Periodicals and Directories Division, Longman House, Burnt Mill, Harlow, Essex CM20 2JE, England). £24 surface, £34 airmail. National Symposium on the Availability of Strategic Minerals, edited by M. J. Jones. London, Institution of Mining and Metallurgy, 1980. 109 pp. 3. NIM reports Report No. 1941 The recovery of chromite and platinum from the UG-2 Upper Chromitite Layer .of the Bushveld Complex at the Pandora Mine (first published 10th Mar., 1978). Report No. .2012 A mineralogical investigation of borehole cores from the Trompsburg Complex (first published 6th Apr., 1979). Report No. 2038 The leaching of sphalerite in acidic ferric sulphate media in the absence of elemental oxygen. Report No. 2052 An investigation of the impurities in native gold by neutron-activation analysis. Report No. 2056 The mineralogy and geochemistry of the copper, lead, and zinc sulphides of the Otavi Mountainland. Report No. 2058 A n elementary introduction to image analysis - a new field of interest at the National Institute for Metallurgy. Report No. 2059 Distributed computer control of industrial processes. Report No. 2060 The analysis, by atomic-absorption spectrophotometry, of activated charcoal.

Jan 1, 1980

By J. H. van Laar, L. J. van der Walt, P. L. Crouse, H. Bissett, G. J. Puts

"SynopsisSilicon carbide nanopowders were produced using a microwave-induced plasma process operating at 15 kPa absolute and at atmospheric pressure. Methyltrichlorosilane (MTS) served as precursor, due to its advantageous stoichiometric silicon-to-carbon ratio of unity, allowing it to act as both carbon and silicon source. Argon served as carrier gas, and an additional hydrogen feed helped ensure a fully reducing reaction environment. The parameters under investigation were the H2:MTS molar ratio and the total enthalpy. The particle size distribution ranged from 20 nm upwards, as determined by SEM and TEM micrographs. It was found that an increase in enthalpy and a higher H2:MTS ratio resulted in smaller SiC particle sizes. The adhesion of particles was a common occurrence during the process, resulting in larger agglomerate sizes. SiC layers were deposited at 15 kPa with thicknesses ranging from 5.8 to 15 µm.IntroductionIt is well known that methyltrichlorosilane (CH3SiCl3 or MTS) decomposes to form silicon carbide (SiC) and hydrogen chloride (HCl) as shown in Equation [1]. The reaction kinetics and mechanisms for this reaction are thoroughly reported in the literature (Sone et al., 2000; Papasouliotis and Sotirchos, 1999; Kaneko et al., 2002; Wang et al., 2011)."

Jan 1, 2015

By H. Manurung, I. M. Bendiayasa, W. Astuti, and H. T. B. M. Petrus, F Anggara, K. C. Wanta

The leaching kinetics of cerium (Ce) and yttrium (Y) in sodium-hydroxide-digested non-magnetic coal fly ash using acetic acid were investigated. The variables analysed were pH, solid-to-liquid ratio (S/L), and temperature. The results show that cerium and yttrium's maximum recovery was 57.33% and 58.36%, respectively, under leaching temperature of 90°C for Ce and 60°C for Y at pH of 1,74 and 10 g/mL solid-liquid ratio in 240 minutes. Increasing the leaching time to more than 120 minutes did not significantly improve the results. After the magnetic separation process, the ICP-OES analysis shows a slight increase in the concentration of cerium and yttrium on nonmagnetic components. The XRD and ICP-OES analysis for the sample before and after silicate digestion shows that 40% silicate was dissolved. The calculation of apparent activation energies of leaching using the Arrhenius law for the leaching of cerium and yttrium gives 22.72 kJ/mol and 35.84 kJ/mol, respectively. The kinetic leaching model of cerium and yttrium all fit Dickinson's new shrinking core model. The calculation results show that the leaching reaction is controlled by combining interface transfer and diffusion across the product layer.

Nov 6, 2024

By B. K. Loveday

A model for the leaching of non-porous particles by B. K. LOVEDAY*, Ph.D. (Fellow) A model has been developed for the prediction of the rate of leaching for an assemblage of non-porous particles in terms of size-distribution parameters. Expressions are developed for batch and continuous operation, and an example of the application of the model is given.

Jan 9, 1975

By A.M. Edwards

1. Book reviews Platinum in South Africa, compiled by A.M. Edwards and M.H. Silk. Randburg, Council for Mineral Technology (Private Bag X3015, Randburg, 2125 South Africa), 1987. 55 pp. U$30. Reviewer: R.D. Wintle Scientific and technological developments in extractive metalurgy-G.K. Wiliams Memorial Volume. Parkvile (Australia), The Australasian Institute of Mining and Metalurgy, 1986. $A12 (incl. surface postage). Reviewer: T.Y. OweD Ion exchange and sorption processes in hydrometa/urgy, edited by M. Streat and D. Naden. Chichester, John Wiley & Sons, 1987. 229 pp. Reviewer: B.R. Green Role of Government in mineral resources development, edited by Michael J. J ones. London, The Institution of Mining and Metalurgy, 1985. 180 pp. £40. Reviewer: K.E. Ducat 2. Recent publications Annual report 1987. International Tin Research Institute, Kingston Lane, Oxbridge, Middlesex UB8 3PJ, England, 1988.Tin and its uses no. 156. Address as above. 3. Mintek reports Application Report no. 5 The production of and alusite and other refractory minerals. 1988. 16 pp. . Application Report no. 6 The development up to commercial application of a process for the recovery of lead, copper, zinc, and silver from the Black Mountain deposit. 1988. 14 pp.

Jan 1, 1988

[Consider a square block W in an ore body S2, to be valued from one centre sample w, and one corner sample w2 (Fig. 9.1). The sample set is ws = Iw,;w21. We can estimate the block average µw by the average of the sample values x, and x2: µw = 'z (x, + xz). (9.1) The error made is measured by the estimation variance: o' (ws to W) = 2 - (ws; W) - - (ws;ws) - - (W; W). (9.2) However, we know that the centre sample w, gives more information about the block value than the corner sample w2. In the example studied in § 8.4, where w, and w2 were considered to be points, we found that of (w, to W) was nearly one third smaller than o2E (w2 to W), therefore when estimating W one should give more weight to w, than to w2. In general, when evaluating a block W from a set of n samples ws, where WS = l w;w2; ... wn1, a better estimator of µw can be obtained if we give different weights to the sample values, depending on the size and the positions of the samples. Some desirable properties of such an estimator µw are: ? It should be a linear function of the sample values xi: n µw = bi xi (9.3) =t where bi = weight given to sample x . ? It should be unbiased, i.e. its expected value should be equal to the true block value: E [µw - µw] = 0. (9.4) ? The mean squared error of estimation of µw should be a minimum E [(µw - µw)2] = a minimum. (9.5) The estimator which satisfies these properties is a minimum variance, linear and unbiased estimator, and is known as the kriging estimator. The corresponding error of estimation is the kriging error. This estimator is also known as the BLUE (for Best Linear Unbiased Estimator) estimator. This was named by Matheron in acknowledgement of the early work of Krige's in the optimization of the evaluation of the South African gold mines. The following notations will be used: µK kriging estimator. o2k = o2K (w,, to W) kriging error.]

Jan 1, 1978

By R. J. Davidson, B. Strong

The piloting and eventual large-scale operation of fixed-bed carbon columns for the recovery of gold from plant effluents is described. A fixed-bed carbon pilot plant comprising three adsorption columns was used for the recovery of gold from clarified plant effluent at the Vaal Reefs Exploration and Mining Company (West Division). The effluent ,which contained 0,1 toO,S g/t of gold and less than 10 g/t of free cyanide, was adjusted to pH 8 prior to use. Daily acid treatment of the carbon circuit with 3 per cent hydrochloric acid was shown to have a most significant effect on increasing the gold adsorption. The acid treatment involved a plant downtime of only I to 2 minutes per day. High loadings of gold (up to 30 k g/t) and copper (up to 75 k g/t) were obtained on the leading column, while the gold recoveries averaged 98 per cent over 17 weeks of continuous operation. The subsequent elution of loaded carbon in a pilot elution column indicated the use of abnormally high amounts of the pretreatment reagent (caustic soda and cyanide) used in gold elution. This was attributed to the high loading of copper on the carbon. However, the elution of both the gold and the copper at 110°C with demineralized water as the eluant was satisfactory. In a similar large-scale operation, three fixed-bed carbon columns each containing 4,5 t of carbon were used to treat 80 to 120 t/h of plant effluent with a gold concentration of about 0,15 g/t. Gold loadings of 5 to 6 k g/t were obtained regularly, while the gold recovery averaged 97 per cent over a 12-month period. The capital cost of the plant was recovered in 2 to 3 months. The evidence presented strongly suggests that copper plays a significant role in the adsorption and elution of gold under the prescribed conditions, and in the subsequent precipitation of gold following acidification of the eluates. The formation of a highly insoluble gold-copper complex produced under acid conditions appears to explain many of the observations made in the investigation.

Jan 1, 1983