Search Documents

T. T. READ, BUREAU OF MINES: Mr. McAuliffe has asked a very practical question. Expressed in another way, the question is: If we have decided to use rock dust to prevent coal dust from exploding, have we got to take rock, that is, solid material,, break it up and finally grind it into dust (and fine grinding is very expensive), or can we take material that is already in a pretty fine state of subdivision and thereby save the expense of pulverizing it? Most of the preceding discussion has been from the view-point of practical experience, and I should like to suggest that we have not had enough practical experience in rock dusting to be able to answer this question, from the viewpoint of experience, with the degree of definiteness that Mr. McAuliffe desires. With your permission I will discuss the matter briefly from the theoretical standpoint, because after all the theoretical considerations, insofar as we understand them correctly, will apply to every' case, whereas in coming to a decision on this matter it will be necessary to take into consideration local conditions, which will necessarily vary in every case. Considering the matter in a rather elementary way, the first point is: What makes coal dust explode? The air of this room is full of dust at the present moment, even though we do not notice it. If you were to close up the room for a week, enough dust would settle on the floor so you could write your name on it. Of course, the dust which is in the air of this room is not coal dust but even if it were coal dust and you were to bring an open light in' here we all know that the dust would not explode. The reason for that is that the dust particles are not close enough together for the flame to propagate itself from one to the next. You will probably be able to see in the demonstration in the gallery on Saturday that the coal dust explosion is practically a very rapid burning of the dust. When you light one piece of dust it burns and gives out heat and if there is another piece of dust close enough to it so that the heat from the first piece is able to bring a second piece up to the burning temperature, then the flame will propagate itself through the mixture. But, if the particles are so far apart in the air that the' heat from one particle is dissipated before it reaches an adjoining one, and is therefore not able to bring the second particle up to the burning temperature, then the flame will not propagate. To get a coal dust explosion, it is not sufficient to have coal dust suspended in the air. The coal dust particles must be close enough together in the air so that the heat from one burning particle is able to heat the adjoining particles up to the point at which they will burn. There has been some discussion of the size of dust particles that will cause an explosion to propagate, and it has been pointed out that the minus 200-mesh dust is the most dangerous, and that particles coarser than 20-mesh will not propagate an explosion. There are two reasons for that. A large particle has very much smaller surface in proportion to its weight than a small particle has. You know the old story about the Indian who when asked how he could go around in cold weather without any clothes on said that an Indian was all face. A 200-mesh particle is almost all surface and there= fore is able to burn almost instantaneously, which means that it gives out its heat almost instantaneously, whereas a large particle with less surface in proportion to its weight burns more slowly, gives out its heat more slowly, and the heat has more time to be dissipated. The second reason why coarse dust does not easily propagate a flame is because it is so hard to make it

Jan 1, 1924

DR. BANOWSKY: Thank you very much. That was the shortest introduction that I have had lately, and I didn't have time to get my coat on. But I appreciated it, and I'm delighted to be here with an industry with which 1 feel strong affinity. At the University of Oklahoma we have an energy history. We are a little more currently involved in oil and gas, and those of you who know the history of our state would be aware we have an early coal development back really before the turn of the century in the southeast part of our state what we call Little Dixie. How many of you have spent anytime in Oklahoma or are from the state of Oklahoma? I'm not going to ask how many are from OSU or the University of Colorado. We did send you a football coach here from Oklahoma, and 1 see you have exchanged him. Several of you were only interested in the lobby in asking about our football team this year. 1 would like to go somewhere where we can talk about something besides football. I'm just trying to build a University that our football team can be proud of. We're going to be strong again. 1 can assure you. We've got the best football team money can buy. It's not quite as bad as the college president who called the coach in and said, "Coach we're in trouble, you're losing games and the alumni is very unhappy." "What can we do?" the president asked. The coach said, "Well the football team is flunking the admissions test. We can't get them in with the standard achievement and SAT tests." The president said, "What can we do?" The coach said, "Well the coaching staff has substituted for the American College Test the simple fill in the blank questionnaire." The president said, "Let's use it. We have got to get the team in." The first question was, Old MacDonald had a (-). And a couple of the big tackles were taking it and one of them said, "Hey, what did Old MacDonald have?" His friend said, "Stupid, Old MacDonald had a farm." "Well how do you spell farm?" He said, "Stupid, e i e i 0." Now the gentleman who met me at the registration line from Lakewood, Colorado, was asking me about one of our great big tackles; and he is doing well. We call him Doctor Death; he is also a wrestler and that gentleman said, "1 don't know how bright he is." 1 said, "He is bright enough for our academic tutoring that he is going to get through all right." So I'm delighted to see you and be here with my very dear friend, Carl Terzian. Carl and 1 were in Los Angeles together for 10 or 12 years when I was president of Pepperdine University. He and I are exactly the same age. Born in 1935 and 1 a month or two later in 1936. Fewer children were born in that period than in any other period of time in this century. For those of you who remember anything about that period, you will know why no one was having babies during that period. But Carl called and said, "Bill do you know where Vail, Colorado is?" Well when you live in Oklahoma, you learn where Colorado is in a hurry. 1 not only know this beautiful area, but have made too much of an investment here at a place called Beaver Creek. The real estate is cheap over there. 1 play regularly in the Gerald Ford Invitational Golf Tournament here. Hope you will visit Beaver Creek. It's just 10- 12 miles to the west. The sight of the 1976 winter olympics until the people of Colorado voted them out. And now Vail Associates and I are good Oklahoma families. Bass family, Harry Bass of course, many of you know this story, who is chairman of the Board of Vail Associates, is making quite an investment in that year-round resort area. Beautiful golf course now. You can come out and afford the green's fee and beautiful, beauti-

Jan 1, 1982

The 78th Regular Meeting of the Rocky Mountain Coal Mining Institute (hereafter referred to as RMCMI) convened at the Marriott's Mark Conference Center, Lionshead Village in Vail, Colorado. The meeting was called to order at 8:45 a.m. by the President, Ira E. McKeever, Jr., who is President, Western Mining Operations, Natural Resources Group, W. R. Grace & Co. McKeever was introduced by Past President Edward F. Ziolkowski, Senior Vice President and General Manager, Energy Development Company in Hanna, Wyoming. MR. ZIOLKOWSKI: The first order of business this morning is to introduce the president and for a business meeting as well as other items on the program. It is my pleasure to introduce Ira McKeever to you this morning. Ira was born and raised in Kit Carson, Colorado, and served in the U.S. Navy prior to obtaining his geological engineering degree in 1952 from Colorado School of Mines in Golden. He then spent the next 20 years involved in mining sulphur, pot ash and coal with Texas Gulf Sulphur at that time and Gulf Resources Chemical Corporation. In 1972 he joined W. R. Grace & Co. as president of the Mining Division, Natural Resources Group. He was named Colowyo Coal Company's president and general manager in 1976 to develop what is currently Colorado's largest coal surface mining operation. Last year he became W. R. Grace's president of Western Mining Operations which is the position he presently holds. Ira is active in civic affairs; he is currently serving on the Colorado Energy Impact Assistance Advisory Committee. He is a member of the Colorado's Metropolitan Water Roundtable, he is also a director of Project Colorado, a member of the committee for the Colorado Division of Commerce and Industry. He has, in the past, served as chair- man of the Craig Hospital Board. In 1967 Ira was the recipient of the Colorado School of Mines van Diest Gold Medal Award, and in 1981 was given the individual service award for outstanding accomplishments in the field of health, promotion, physical fitness by Colorado's Governor's Council for the Health and Promotion of Physical Fitness. Memberships are also held in Denver Coal Club, the Colorado Mining Association, and the American Mining Congress. Will you please welcome Ira McKeever? I do have one other piece of business here. If you will all join with me, yesterday was Ira's birthday. I asked what year that was, but I couldn't get that out. So, I'm not going to lead the singing. Someone is going to lead the singing. But I think it would be appropriate if we did sing happy birthday this morning and I think it would also wake us up. How's that? All right, will you join me please? (A chorus of the Happy Birthday song followed.) President McKeever's address: MR. McKEEVER: The secret is that I'm double nickles. So I've got a few more years hopefully to be with you and this wonderful industry that we represent. Thank you Ed. I realize now more than ever, the tremendous effort that you put in the program last year and the magnitude of the job that is placed in the presidency of the Institute. It was indeed with tremulous hands that I undertook to lead the Institute this year, and I found a tremendous amount of strength and guidance in my friend Ed whom we've known since college days and worked together. On behalf of that lifetime of memories and good thoughts, Ed, I would like to present to you a little token of appreciation. 1 would like to join Ed in welcoming you all to Vail. Ed arranged the weather, 1 arranged the program along with Charlie Margolf. This is the 70th regular meeting of the Rocky Mountain Coal Mining Institute; and in accepting the leadership a year ago, 1 obligated one very special person to fill the role of chairlady and hostess for this meeting. I would like to have you all, if you haven't already, meet my wife, Linda. I would like to thank her publicly for her guidance and help she continues to provide me. It's absolutely necessary that you also meet and recognize Charlie Margolf our program chairman who will be helping through the meeting to present and monitor our program; and anyone who knows Charlie knows the sincerity and dedication he brings to anything or any phase of life he touches. We will be seeing him in action this afternoon when he chairs the most interesting panel presentations. Don't miss it if you can help it. A couple of logistical comments. We will have to keep our meeting on schedule so that any of our non-agenda items that we need to keep, maybe we

Jan 1, 1982

By Geo. A. Murphy

MR. ARTHUR E. GIBSON (General Manager, Consumers Mutual Coal Company of Utah) : I suppose the reason I was called upon to read this paper was because I was at the mine for several years, but I have not been there for the past four years and the installation has been put in since I left. This article has been written by my successor-it follows: At the very urgent solicitation of your Secretary I have consented to prepare this paper descriptive of the spiralizing plant which is a part of the new steel tipple recently erected by the Spring Canyon Coal Company to serve its mines at Spring Canyon, Utah. I have been reluctant in giving this consent for two reasons: one of which is an excellent one, and the other isn't any good at all. First,, I find that it takes a long time to become familiar with the eccentricities of spirals-to get wise to their whims and peculiarities, and while this plant has been in operation for a number of months, something new seems to crop up nearly every time I see it, and -it would be impossible to describe all of these things even if I remembered them. The second reason is, purely personal. Among the many things I have learned by attending the sessions of the Rocky Mountain Coal Mining Institute is that if a man is not pretty sure of the ground he attempts to cover, he had better keep his mouth shut, because if he isn't right, he is dead sure to be called down by someone. However, as I will not attend the session, this feature will not hurt much, but it will make it necessary for someone else to read the paper and this will make it much better for those who are obliged to listen to it because I don't read English very well. To begin with I will say that what is said in this paper applies only to the plant under discussion as I have had no experience with any other plant. While spirals have been in use for quite a number of years, and there are some large plants in the East, their use has not been general, and I believe the plant at Spring Canyon is the only one in the United States west of the Mississippi River. The details of the plant were worked out by Mr. Thos. R. Stockett, General Manager of the Spring Can= yon Coal Company; it was manufactured by the Anthracite Separation Company of Hazelton, Penn., incorporated in the design and erected by the Link-Belt Company of Chicago, in connection with the balance of the tipple. It consists of five units. Each unit consists of a vertical wood column about 6 inches in diameter, and 9 feet 6 inches in height, around which the spiral is built. It is something like a triple screw conveyor, set vertically, with flights down which the coal and refuse travel by gravity in the process of separation. There are three of these flights, forming a sort of nest but about 7 inches apart, and they make 21 turns around the column in its length. These flights dip toward the column about 27 degrees; they have a uniform pitch downward of 31 degrees; they are 19 inches wide at the top (measured from the column) and taper gradually until they are about 9 inches at the bottom. They are not made with one continuous plate from top to bottom, but are made up of a number of plates. Some of these plates are slightly waved, others have small corrugations in them and still others are perforated with small holes, all of which are intended to accelerate or. retard the movement of the coal and refuse as they pass down, At intervals there are adjustable plates in the flights for the purpose of decreasing the maximum outside;

Jan 1, 1926

By F. A. Young

A description of the dry process coal cleaning plant which has been built and operated by St. Louis, Rocky Mountain & Pacific Company at their mine at Brilliant, New Mexico, should at first be a description of the special machinery which is used in this process. This equipment consists primarily of screens for sizing the coal into six different sizes all smaller than 1 ½ inch and the pneumatic machines for cleaning each size. These machines are patented and were manufactured by Sutton, Steele & Steele of Dallas, Texas, until a few months ago when all rights of sale were acquired by the American Coal Cleaning Corporation. These screens, a plan of which is now before you, are called anti-gravity screens because the coal travels up hill. The screens which we have at Brilliant are 3 feet wide and 7 feet 4 inches long. They consist of one upper deck which slopes upward in the direction of the flow of the coal, at an angle of 12 degrees. This deck is a wire mesh screen the size of which determines the size of oversize from that screen. Under this is a lower deck with a slope of 7 degrees. This is a solid bottom and is for advancing the undersize to the next screen. On account of the difference in pitch of these decks they are about 11 inches apart at the discharge end, which allows the oversize to be taken off at one or both sides and the undersize to fall only a few inches on to the following screen. This is perhaps the most valuable point in this patent as it allows any number of screens to be placed on a-level floor, tandem in a battery without elevating or rehandling the coal in any way. The length of the screens corresponds to the proper spacing of the cleaning tables which naturally operate on the floor below. I know of no other screen which can be operated in this way. The coal is caused to travel by a reciprocating motion. A shaft as shown near the center of the screen box and under it has an eccentric at each side of the screen with connecting rods attached near the rear of the screen box. The screen box is attached to the stationary under frame by means of cast iron plates extending full width across the screen box. These are placed at an angle as shown so that the forward motion of the eccentrics causes the screen box to rise as it moves forward and the backward motion drops the screen from under the coal thereby causing it to advance. The coal advancing over the screen cloth in this rolling or jumping motion causes very perfect sizing. It should be stated here that very accurate sizing is necessary for the success of the cleaning tables. The stroke is 1 inch and the speed 350 revolutions per minute. In describing the pneumatic cleaning table, I place before you a plan furnished by the makers. The basic principle is that if a film of coal one to two inches thick and all of nearly the same size pieces is placed on a flat perforated surface and a large volume of air passed through it, the lighter particles which are the clean coal will soon find their way to the top of the film, while the heavier particles, or waste, will remain on the bottom. The machine is built with a perforated deck about 4 feet square under which is an air chamber and air duct connecting with a fan which is part of the machine. The deck of the table has a reciprocating motion the same as the screens already described, which tends to advance the product up a slight slope which is adjustable. The coal is fed at one corner of the table as shown and the deck slopes also away from the feed and at right angles to the reciprocating motion. On top of the perforated deck are riffles about 2 inches apart and running parallel to the line of reciprocating motion. These riffles are about 1/2 inch high at the fan and feed side of the table and taper to nothing at the far side. When the coal is fed on to the table, the air through the perforations tends to raise it 'and roll it over these riffles down the slope toward the clean coal discharge. The heavier particles do not get over the riffles so rapidly and the reciprocating motion is constantly pushing them

Jan 1, 1923

At the Annual Meeting of the RMCMI Board of Directors held June 29, 1985, the following amendments to the corporation bylaws Article III were made: Section 2. Advisory Board. There shall be an Advisory Board of Directors which shall be com- posed of all former presidents of the corporation and of the unincorporated association, also known as The Rocky Mountain Coal Mining Institute, of which the corporation is the successor. The Advisory Board shall periodically review the philosophy and policies of the corporation and make recommendations concerning the same to the Board of Directors. The Advisory Board shall hold an annual meeting at the same place as and immediately pre- ceding the annual meeting of the members in each year and written notice stating the place, day, and hour of the meeting shall be given or mailed to each member of the Advisory Board at least thirty days prior to the date fixed for such annual meeting. The annual meeting of the Advisory Board shall be for the purpose of electing a chairman from among its members and the person so elected chairman shall also serve as a member of the Board of Directors of the corporation. The Advisory Board shall meet at such other times and conduct its affairs in such a manner as it shall determine from time to time by resolution. Section 4. Regular Meetings. A regular meeting of the Board of Directors shall be held immediately following the annual meeting of the members, at the site of the annual meeting of the members, the day and time to be fixed by the Board of Directors at its annual meeting immediately pre- ceding the annual meeting of the members in each year, without the necessity of any other or advance notice. Such regular meeting of the Board of Directors shall be for the purpose of considering committee appointments, and for the transaction of such other business as may come before the meeting. A regular meeting of the Board of Directors shall also be held in the Fall of each year following the annual meeting of the members and written notice stating the place day and hour of the meeting shall be given or mailed each member of the Board of Directors at least thirty days prior to the date fixed for such regular meeting. Such Fall regular meeting of the Board of Directors shall be for the purpose of receiving the treasurer's annual financial report of the previous fiscal year as reviewed and approved by the auditor, to take action on the budget, and for the transaction of such other business as may come before the meeting. Section 8. Standing Committees. The Board of Directors may create by resolution adopted by a majority of the entire Board of Directors, a Bylaws and Resolutions Committee, a Nominating Committee, a Finance Committee, and one or more other committees each of which shall consist of two or more directors and which shall have and may exercise such authority in the management of the corporation as shall be provided in such resolution or in these bylaws. Section 9. Ad Hoc committees. The Board of Directors from time to time may by resolution create a Membership Committee, a Scholarship Committee, an Education Committee, various convention committees, and one or more other committees each of which shall consist of members of the corporation and which shall have and may exercise such authority, other than in connection with the management of the corporation, as the Board of Directors may determine. MINUTES of the Rocky Mountain Coal Mining Institute 81 st Member Annual Business Meeting July 2, 1985 The 81st Annual Business Meeting of the mem¬bers of The Rocky Mountain Coal Mining Institute was called to order by the president, Charles W. Margolf at 1:35 p.m. Tuesday, July 2, 1985 in the Windom Peak Room of the Tamarron Resort near Durango, Colorado. Thirty members were present and a quorum was established. It was moved by Bill Balaz, seconded and car¬ried to dispense with the reading of the minutes as these were published on pages 67 thru 77 of the 1984 issue of the Proceedings. The chair called for reports of the various com¬mittees and these reports will be placed on file in the RMCMI Office. Bylaws and Resolutions. Chairman Loren V. Linville reported that the Board of Directors had adopted changes to Article III, Sections 2, 4, 8 and 9 calling for clarification of Ad Hoc and Standing Committees as well as setting forth a purpose for the Advisory Board meetings and stating a time for an annual meeting. He further reported that the Board had passed three resolutions: (One) Noting the passing of these members since the last conven¬tion - Einar M. Arentzen, Gerhardt A. Benne¬witz, Claude P. Heiner, Raymond A. Johnson, Vard H. Johnson, P. T. Schonstrom, Augusta F. Whiteside and Edward Wiemann; (Two) Of appreciation to the officers, chairmen and their commit-

Jan 1, 1985

By Geo. A. Brown

This paper was written from conditions existing in the Cumberland Mines of The Union Pacific Coal Co., with my impressions and cause of same. These mines are located on a branch line of the 0. S. L. R. R., about sixteen miles south of Kemmerer, Wyoming. The mines are the property of The Union Pacific Coal Company with headquarters at Rock Springs, Wyo. There are two mines, No. 1 and No. 2, located about two miles apart in a seam of coal averaging about 16 feet thick which is split with a parting of rock from 4 feet to G feet from the bottom, averaging from 4 inches to 5 feet thick, mostly of soft fire clay, with an average pitch of 21 degrees to the west. The lower coal below the fire clay band being of a soft nature, much softer than the coal above it. The cover or roof next to the coal is of a massive sandstone formation from 4 feet to 60 feet thick while the floor of the seam is of a soft fire clay as far down as has been prospected. These mines are also of a dry and dusty nature, they generate lots of fire damp and are subject to fires from numerous causes. These mines were opened up in 1900 with five openings each, Main Slope, North and South Manways and North and South Aircourses driven parallel directly on the pitch of the seam which is fairly regular, entries being turned North and South at right angles off the slope about 300 feet apart. The entries were driven double 10 feet wide with chain pillars from 20 feet to 30 feet thick. The main entries are used for haulage and main intake, back entries for return aircourses. Rooms are turned on 50-foot centers and 20 feet wide, directly on the pitch Galvanized sheet iron chutes are used in the rooms. The slopes were driven down in No. 1 mine about 4,000 feet, in No. 2 mine about 5,000 feet where the cover would be about 1,400 feet in No. 1 mine and about 1,700 feet in No. 2 mine approximately. When a point about 2,000 feet on the slope had been reached with cover, 600 or 700 feet squeezing became noticeable on the entries and room pillars with slight bumps which extended clear to the upper entries of the mines and continued to get worse as the mines got deeper and with more cover as no pillars had been removed at this time. It should be stated here that faulty ground was found on the south side of No. 2 mine and on the north side of No. 1 mine, in some places looking like a fault of a down throw, some places like a want and other places like an erosion. The latter theory seems to be correct from prospecting and drilling. The mining of entries and rooms became more difficult with more squeeze and bumps of increased pressure which closed entries and aircourses and finally caused the lower workings of the mine to be abandoned. It was then decided to open up the entries from the 6th up, or approximately half way up the slope. The opening of these entries was started with the intention of extracting pillar coal but considerable danger was met with for the entries .were squeezed tight and when they were disturbed, bumps and squeeze conditions had to be contended with, also gas and fires due to the continued grind on the pillars due to overhead pressure bringing on friction which caused innumerable fires to start in the bottom coal. Bumps being so extensive at times as to close up aircourses for 500 or 600 feet, also discharge timber, coal and rock from the rib of slope and entries for hundreds of feet, dislodging tracks and throwing mine cars around just as if an explosion had taken place, filling places with gas and throwing dust into the atmosphere so that you could cut it with a knife. It became necessary to discontinue the use of black powder and naked lights entirely as a safety precaution. Permissible Powder Monobel No. 5 and Wico Electric Safety Lamps were installed. All coal was shot off the solid whenever it was necessary to shoot. ' In opening up these entries it was found that practically all of the weight was centered on room pillars up to the first crosscut chain pillars and barrier pillars between top of rooms of entry below and the one above which averaged 30 feet thick and in all practically 120 feet of ground. The rooms were mostly open from the first crosscut up to the face which showed that the points mentioned had taken the weight. It was found impossible in some of these entries to drive double entries again as the bumps and squeeze made it impossible to maintain them. This made ventilation quite a problem, small booster fans and flexoid tubing being used for ventilation until one entry could be connected with the one above which has solved most of our ventilation problems so far.

Jan 1, 1924

Jan 1, 2009

Jan 1, 1942

The following pages contain valuable information about the products and services offered by our advertisers

Jan 1, 1982

Jan 1, 1995

By K. L. Marshall

A facetious title was purposely given this talk, so that a formal paper would not be expected. TWO or three days ago, while discussing with Mr. Dickinson some of the details of the dust explosion demonstrations we are planning for this coming Saturday, I remarked that we would like to have as many people as possible see some samples of 20 and 200 mesh dust, so they would more fully understand just what was causing the explosions. Mr. Dickinson requested that I bring samples and screens and in this informal manner, give you all a ".close-up" of coal dust which is considered in Explosion Hazard reports. While sampling mines, for road, rib, and roof dust, in connection with safety service and hazard reports which the Bureau of Mines Engineers make at the request of coal operators, I have often been assisted by under- ground mine officials or other men of many years experience and on almost every occasion, while we were carefully brushing the very fine dust from timbers or coal surfaces, they would make some remark such as: "never had noticed this kind of dust, didn't know it was here", or "well, that's the first time I really understood what all 'this dust talk was about." Such experience makes me believe that the much published terms, 20 mesh and 200 mesh are just numbers to the great majority of both miners and operators. We are now going to have lesson one in the primer of coal dust explosions and I want to say, in all sincerity that a complete course in the hazards of mining is deserving of a place in the curriculum of the best mining schools of this country. Sample No. 1 is fine coal and dust and is a fair sample of what can be found every where in rooms and entries of a mine, as it is too small to be gathered up with a shovel and is left in the ordinary mining at the faces and is spilled along the entries in haulage. In this you will see some quarter inch coal, much eighth and sixteenth inch coal, in fact those are the sizes I find many people have in mind when they are asked about the dust made in mining. Although the sizes mentioned are the ones which seem to almost entirely make up this sample, such is not the case, for from 10 to 20% of such a sample will usually pass this 20 mesh screen and in Sample No. 2 we have 20 mesh dust. Result of many tests, supports .the statement of the coal mining division of the Bureau, that it is quite probable that coal over 20 mesh does not take part in any but the most violent of explosions and that all dust under 20 mesh may take part in any explosion. The largest particles in this sample will not be over .03 inches in their largest dimension and a pound of dust to a foot of average heading is very easily found in most every mine I have visited and usually a great deal more can be readily gathered up. It was .found early that the finer the dust the more dangerous it was for a given coal. So for the early explosion tests conducted by the Bureau a commercial pulverizer was used and it turned out a 20 mesh dust of which about 75% would pass 200 mesh. Some men question whether the ordinary mining methods made such a dust and so doubted the explosibility of the dust in their own mines. The question was well taken, and hundreds of dust samples were taken by the field men of the Bureau to determine the kind of dust being made in all methods of mining and all classes of coal. The result of such sampling showed some coals. resisted breakage more than others and that actual mine road dust, through 20 mesh, would show from 10 to 20% through 200 mesh, and for actual rib and roof dust through 20 mesh, they would get from 20 to 40% of 200 mesh dust. In testing the

Jan 1, 1924

By Robert M. von Storch

Chairman Doc, distinguished guests, and fellow members of the Rocky Mountain Coal Mining Institute: It's a genuine pleasure to meet with you again at the 54th regular meeting. I might add that it is always pleasant to be at the top of the batting order. The field is wide open since there is no danger of repeating something already said. At the same time, I am aware that the lead-off speaker has a responsibility to avoid stepping on the toes of subsequent speakers. I promise to confine my remarks to areas other than those to be covered by the well qualified speakers that follow. During our meetings at this convention, many fine papers will be presented. Our thanks are due Bob Williams and his hard working program committee for the superior selling that brought so many eminent speakers to our meeting. And, of course, our special thanks go to Doc Schloss, general chairman of this meeting. Doc and his able colleague, Stan Shubart, have been the spark plugs that fired up all of the arrangements we are enjoying here in Glenwood Springs. I'm sure all of us are appreciative of the many hours Doc has devoted to seeing that our meetings will be pleasant and profitable. When we mention arrangements, we always think of that master arranger, Fred Whiteside, who, as a charter member and secretary-treasurer of the Rocky Mountain Coal Mining Institute, has had more to do with more matters around these parts than just about anyone I can think of.

Jan 1, 1958