Search Documents

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in develop¬ment of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-L Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

By Eric E. Cather

In 1981 the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 5,100 acre (2,065 ha) Rubicon RARE II area (No. 5026) in the El Dorado National Forest (fig. 1). Work by the Bureau of Mines indicates that potential for mineral resources in the area is low. Samples from small gravel deposits along the Rubicon River and from favorable structures in the area contained smart amounts of economic minerals. A Tertiary river channel near the north area boundary contains gold values as much as $137.60 per cu yd ($180 per cu m) [(gold at $400 per troy oz ($12.86 per g)]. The channel does not cross the study area. Energy resource potential, including oil, gas, or geothermal, does not exist in this geologic environment.

Jan 1, 1982

By M. A. Mahtab

This report presents a new procedure for analyzing the orientations of rock fractures in an engineering site. This procedure, coded in a computer program, identifies clusters or groupings among the fracture orientations and calculates (1) the mean orientation of the fractures within each cluster and (2) the dispersion or scatter among these fracture orientations. Data points are represented by intersections of joint normals with the upper hemisphere, which is divided into 100 equal-area quadrilateral patches. The points in adjacent patches where the Poisson distribution test shows significant concentrations are assigned to a single cluster. For a cluster whose fracture orientations follow Arnold's hemispherical normal distribution, a confidence interval for the fracture orientation mean is calculated by applying Fisher's estimates. The technique is applied to the treatment of three examples.

Jan 1, 1972

By P. L. Woolf

Oil was successfully injected into the tuyeres of the Bureau of Mines experimental blast furnace. Determinations were made for the minimum oil addition necessary to permit the maximum available blast temperature of 2,250° F. and the maximum oil rates at blast temperatures of 1,900°, 2,000°, and 2,100° F. From these tests, the upper and lower levels of high-temperature heat input, which limit the smoothly operating furnace, were established. Substantial coke saving was realized with maximum oil injection. Oil-to-coke replacement ratios have been calculated for various conditions, and oil is compared with natural gas and moisture in somewhat general terms. A study of the effect of variations in slag volume and basicity on the sulfur content of the metal at high sulfur loads was made.

Jan 1, 1963

By B. J. Scheiner

A ferrous chloride-oxygen leaching system was investigated by the Federal Bureau of Mines to determine its effectiveness for recovering copper and silver from a tetrahedrite concentrate that had been pretreated to remove a majority of the antimony. The pretreated concentrate contained coppers, silver, lead, zinc, antimony, and arsenic. Parameters affecting metal extraction (such as temperature, pressure, amount of ferrous chloride, and initial hydro-gen ion concentration) were studied. Copper extraction of 98 pct was achieved by leaching 4 hours at 40 pounds per square inch gage (psig) and 100° C. Copper was recovered from leach solutions by cementation with iron, and the resulting ferrous chloride was recycled. Leaching the residue with cyanide followed by electrowinning recovered 99.7 pct of the silver. Iron, antimony, arsenic, and sulfur reported to the tailings.

Jan 1, 1978

By Fred Leighton

The Bureau of Mines monitored a rock-burst-prone pillar in a metallic ore vein, up to and through failure, to measure its reactions to increasing loads, as it was mined. Three parameters were monitored: the stress changes at chosen points within the pillar, the displacement characteristics of the drift above the pillar, and the micro-seismic activity in and around the pillar. In descending order of effectiveness, the microseismic technique, vibrating wire stress measurements, and displacement measurements reflected the pillar reactions, and all showed good correlation to one another. A major rock burst in the pillar, which destroyed about 100 feet of drift above the pillar, occurred at the end of this study. This burst was preceded by a large anomaly in the microseismic activity in the failure area.

Jan 1, 1982

By D. E. Kirby

In the preparation of beryllium-copper alloys by fused-salt electrolysis, beryllium was electrowon from beryllium oxide dissolved in fluoride electrolytes and deposited on copper cathodes. At 880° to 1,030° C, deposition was on solid cathodes. Beryllium deposited on the copper, forming a liquid alloy that dripped from the cathode. Dripping alloys containing 3 to 4 weight-percent beryllium were produced with as high as 90 percent cathode current efficiency, by electrolysis at 910°.C. To prepare alloys of higher beryllium content, attempts were made at depositing beryllium on liquid copper cathodes. These efforts were generally unsuccessful, although alloys containing as much as 12 percent beryllium were prepared by this method. At temperatures of 1,100° to 1,300° C, requisite to maintaining beryllium-copper compositions as liquids, the beryllium reacted with cell structures.

Jan 1, 1972

By E. Morrice

Gadolinium, dysprosium, and yttrium are difficult to electrowin as high-purity liquid metals because of their high melting points (>1,300° C). Samarium metal is difficult to prepare directly by electrolysis because the metal reacts with the electrolyte. In this Bureau of Mines study, the rare-earth metal was electrodeposited on a solid manganese, chromium, or iron cathode to form a low-melting alloy. The alloy was then vacuum distilled to separate the rare-earth metal from the ferrous metal. A typical samarium metal product, obtained as the distillate from vacuum distillation of a samarium-iron alloy, contained 150 ppm oxygen, 80 ppm carbon, and 50 ppm iron as impurities, Gadolinium metal, obtained as a residue from the distillation of a gadolinium-chromium alloy, contained 300 ppm oxygen, 200 ppm carbon, and 100 ppm chromium.

Jan 1, 1969

By Ann G. Kim

Methane in coal constitutes a serious hazard during mining. Draining the methane from large blocks of coal in advance of mining is an effective method of improving the safety and efficiency of coal mining. Because of the similarity of the two gases, drained methane can be recovered and added to pipeline supplies of natural gas. To effectively apply advance drainage techniques and recover drained gas, a gross estimate of the methane content of coal is necessary. Using data from previous investigations, the virgin reserves of the Pittsburgh coal in the central and southwestern parts of Washington County, Pa., are estimated at over 1.5 billion tons, with a methane content of 50 to 100 fts/ton. The Pittsburgh bed in this area of approximately 265 mi2 contains over 130 billion ft3 of methane.

Jan 1, 1974

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

By R. S. Norman

The objective of this program was to select approximately 100 acoustic materials for flammability evaluation. Noise control programs have been initiated on several types of mining equipment and vehicles which can be used in underground coal mines. Often, the materials which are used in these noise reduction programs have not been tested for flammability properties according to the same reference standard. During this program a variety of materials were selected for measurement according to ASTM E-162 procedures. A radiant heat energy source was used to measure flammability properties of 15.2 x 45.7 cm. samples. In the absorptive materials category, 45 percent of the materials tested had a flame spread index of less than 25. For barrier, damping, and isolation materials the corresponding values were 40, 43, and 9 percent.

Jan 1, 1979

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

By Lambert Dolphin, George Oetzel, Robert Bollen

An electromagnetic sounder developed for an archaeological application in Egypt has been successfully tested in a California dolomite mine. Chambers in the mine 100 to 130 feet from the surface gave intense, well-defined echoes consistent with an average attenuation coefficient of 0.6dB/m and a relative dielectric constant of 11. By moving the transmitter and receiver units on the hillside above the underground chambers, various characteristics of the propagation could be observed such as dispersion, chamber aspect sensitivity and cross section. The transmitted pulse was one to one-and-a-half radio-frequency cycles long at a peak power of 0.2 MW. Frequencies employed were 16 to 50 MHz. The light weight, highly portable, battery-powered equipment is potentially suited to other underground sounding applications.

Jan 1, 1973

By V. F. Parry

 The amount of energy required to support a unit volume of industrial production appears to depend on the volume of industrial production, effi- ciency of utilization of fuel, the form of energy used, climate, and popula- tion served. Previous to the first World War, industries of the United States were learning how to use the vast resources of energy that were available. From 1895 to 1900 the total amount of energy produced was equivalent to 3.7 tons of 13,100 B.t.u. coal per capita, but from that period until 1920 the energy used increased steadily until it reached an average of 7.7 tons per capita. Since that time the amount used has fluctuated with business con- ditions and has averaged 6.9 tons per capita.

Jan 1, 1943

By Tom Tallone

In the majority of metal and nonmetal mining operations, narrow vein deposits are being mined with slusher hoists. Thin; method of mucking is costly, due in part to its inherent labor intense operation and to its inability to muck 100 pct of the deposits. Mechanized equipment would greatly improve the material handling in narrow vein mining and would dramatically reduce the operational cost. The Compact Loader/Trammer, known as the "mini-mucker" has been developed to increase productivity of the load/haul/dump portion of the typical narrow vein mining cycle. This is Volume II of the final report and concerns the operation and maintenance of the mini-mucker. Volume I covers a general and design review of the activities on the subject contract and are available under separate cover.

Jan 1, 1985

By William J. Campbell

The purpose of this investigation was to extend the analytical services which are required for Bureau of Mines programs in developing and evaluating high-purity materials. Determination of trace elements in minerals and ores as an aid in geochemical evaluation and prospecting was considered. Serious consideration should be given to the merits of using the avail- able fluorescent X-ray spectrographic instrumentation and techniques for determining trace elements. Limits of detectability for trace elements in metal, oxide, solution or mineral samples range from 0.1 to 100 p.p.m, depending on the element being determined, overall sample composition, and the complexity of the X-ray spectra; limits of detectability range from 0.01 to 1 microgram for elements that have been preconcentrated by a chemical or physical process, for example, by ion-exchange membrane.

Jan 1, 1962

By D. Harry Chambers

The Bureau of Mines, through a memorandum of agreement with the Department of Defense, conducted research to recover silver from aircraft scrap. Silver was recovered by an electrolytic method from stainless steel honeycomb sections separated from the aircraft. These sections had been constructed by sandwiching a stainless steel honeycomb core between stainless steel sheets and then brazing the assembly with a silver alloy. Over 300 pounds of silver was used in the B-58 bomber, concentrated in certain honeycomb sections of the aircraft. Following shredding of the aircraft parts, an average of 95 percent (ranging 67 to 100 percent) of the silver was recovered in a single electro-refining step. After the electrorefined product was magnetically cleaned, purity of the recovered silver was greater than 99.3 percent.

Jan 1, 1980

By Alexander May

The Bureau of Mines, in cooperation with the Florida phosphate mining industry, investigated the dewatering of waste phosphatic slimes. Part of this investigation was to determine the electrophoretic mobilities and cation exchange capacities of the slimes. The mobilities and exchange capacities are reported for samples of slimes taken from 15 plants operating in the Florida land-pebble phosphate district that includes Polk,Hillsborough, Manatee, Hardee, and DeSoto Counties. The electrophoretic mobilities determined were all negative, ranging from -0.24 to -1.93 (micrometers per second) per (volt per centimeter). Also reported are frequency distributions of electrophoretic mobilities, electrophoretic mobilities of slime diluted with distilled water and electrophoretic mobilities of sand-slime mixtures. The cation exchange capacities ranged from 17 to 45 milliequivalents per 100 grams of slime solids.

Jan 1, 1975

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in development of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-L Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

Development of automatic fire protection systems for large, mobile mine haulage equipment was initiated under Department of Interior's Bureau of Mines-FMC Corp. contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment June 1972 to May 1973." After successfully designing and mock-up testing an effective economical automatic fire protection system, and after having demonstrated that the system could extinguish controlled fires on 100-ton capacity haulage trucks, USBM-FMC contract 110232059 was issued in June, 1973, to conduct further development and validation testing. This report documents technical progress and activity under the latter contract. Figure 1 shows areas of the two haulage trucks that were protected by the automatic fire protection systems tested during this program. Figures 2 and 3 are composites showing hardware and schematic diagrams of the systems tested.

Jan 1, 1974