Search Documents

By Kato T, Eguchi M, Seino T, Itagaki K, Kimura T, Muto T, Shimizu T, Kobayashi T

Behaviour of minor elements in the dust collecting system connected with fluidized bed roaster for zinc concentrate was investigated by use of the bench scale experimental appara- tus. The dust collecting system was consisting of two dust chambers, hot electrostatic precip- itator, washing tower, mist electrostatic pre- cipitator, drying tower, absorption towers and potassium permanganate solution towers. Some volatile elements such as lead, cadmium and arsenic tend to concentrate in the fine calcine obtained in hot electrostatic precipitator especially in the case of the roasting with insufficient air supply. Special attention was paid to behaviour of mercury. In the roasting tests for plain zinc concentrate, it was considered that most mercury volatilizes at first as elemental vapour in the roaster, but with decrease in temperature of gas around a half of mercury forms compound, and both elemen- tal and compound forms of mercury were found in the gas stream. Elemental mercury is of course difficult to be trapped in the dust collecting system. To promote the compound formations, some additives for concentrate, such as selenium and halogens were effective, especially selenium of a few times equivalent to form HgSe repre- sented complete conversion of mercury from elemental to compound. To clarify the behaviour and removal mech- anism of mercury, various small scale laboratory tests were also carried out. It was confirmed that mercury sulfate formation is possible if temperature and flow rate are adjusted adequate- ly for gas stream consisting of 02-SO2-N2. To trap elemental mercury, various substances were tested, and excellent results were obtained with selenium. Satisfactory results were obtained with a selenium disc heated at 100 to 200¦C in a mercury containing gas stream. Also, applica- bility of scrubbing method with SeO2 solution was investigated, and the solution containing a few hundred ppm SeO2, 0.01 per cent additive and 6 per cent H2SO4 proved to be satisfactory.

Jan 1, 1980

By Dmitrievskaya TY, Cheremnykh PA, Kuftinova IV, Yaremenko VN

The comprehensive processing of raw materials and the tendency to waste-free production require the combination of various methods of concentrating mineral resources. Magnetic separation, an ecologically clean method of concentration, is one step in the technological cycle of ore processing, and cleaning and classifying of raw materials. Separators with superconducting magnetic systems cooled by liquid helium are the novel equipment for practical concentration. Recently, high-gradient (HGMS) and open-gradient (OGMS) magnetic separators using the effect of superconductivity have appeared. The separators of the first type are expedient in the head-end of the technological cycle, as they are most efficient for processing of particles 100 ¦m and greater in size. In this case the main task is to obtain pure tailings with a minimum amount of the useful component. This method allows the essential reduction in the cost of the subsequent crushing and grinding, because only the magnetic concentrate is directed to further processing. The separators of the VGMS type are used more efficiently in the final stages of the concentration cycle to condition the end product. The present work is devoted to the theoretical and experimental investigation of the motion of weakly magnetic particles in the working chamber of superconducting separators of the open-gradient magnetic separator (OGMS) and HGMS types. The flat OGMS is equipped by a magnetic system with NbTi racetracks cooled by liquid helium. The chamber is divided into zones by partitions parallel to the plane of the magnetic system. It is shown how, depending on the number of the zones and their depths, the extraction function of the OGMS varies and the transition from the OGMS to the HGMS occurs. The particles 2 mm and less in size are considered. The extraction parameter distribution of the particles was measured for a multicomponent weakly magnetic ore. It was experimentally shown that xD2 is the extraction parameter for the particles in the OGMS on condition that (p-po)D /l8/tl/g

Jan 1, 1993

By A Batnasan

The main techniques for removing phosphorus as an impurity element in iron ores are physical separation (eg magnetic separation, flotation) and chemical separation (acid leaching, alkaline leaching and bioleaching) processes. When phosphorus occurs in iron ores as phosphate minerals (eg apatite), physical separation techniques are available to remove the gangue minerals from iron ores. On the other hand, chemical separation techniques are suitable for reducing phosphorus levels when phosphorus is associated with iron oxides and hydroxide minerals (eg hematite and goethite) in iron ores. In this study, the dephosphorisation behaviour of high‐phosphorus iron ore was investigated using a combined alkaline roasting and water washing route. Roasting experiments were conducted in a laboratory electric muffle furnace using various concentrations of sodium hydroxide (0–50 g/kg-ore) at different temperatures (100–800°C), varying prolonged roasting times (0–2 h), and different particle size fractions (-45 – -250 μm) of iron ore. Subsequent water washing experiments were employed at various pulp densities (30–1000 g/L) and different times (30 s – 60 min) at ambient temperature. Hematite and goethite were the main minerals in the high-phosphorus iron ore identified using X-ray diffraction (XRD) analysis. The iron ore assaying 63.40 mass % Fe (total), 0.240 mass % P, 4.53 mass % SiO2, and 4.87 mass % Al2O3 were determined using X-ray fluorescence (XRF) analysis. The results showed that the dephosphorisation rate of the iron ore was reached 40 per cent under roasting with 50 g/kg-ore NaOH at 300°C for 2 hours followed by water washing for 30 s with a pulp density of 300 g/L, reducing phosphorus level from 0.240 mass % to 0.142 mass %. At the same time, the iron grade was reduced from 63.4 per cent to 59.5 per cent, caused by an iron loss. Results suggest that the phase transformation of goethite induces the dephosphorisation of high-phosphorus iron ore under alkaline roasting conditions

Aug 22, 2022

Hard rock TBMs are very often open machine layouts, with just a part roof shield over the front of the machine. The whole system is designed for fast face advance and the economy of the project often depends entirely on the rate of advance. Typically, hard rock conditions will demonstrate stable and good ground for a major part of the tunnel. However, short sections of crushed shear zones with clay and gouge material may cause serious time delays. Spiling rock bolting has been proven to be very efficient under such circumstances, provided the fully grouted rebar bolts can be placed in a controlled and practical manner.Environmental restrictions are becoming more and more a part of tunnel excavation projects. Even hard rock TBM tunnelling may require a strict ground water control, because of consequences on the ground surface from lowering the ground water level. Such consequences may be surface settlement, negative influence on ground water resources or damage to vegetation.Pressure injection ahead of the advancing tunnel face (in this paper named pre-injection), using microfine cement and chemical grouts, is today a proven technology. As examples can be mentioned (Garshol, 1997) about 100 km of pre-injected tunnels below Oslo City and about the same length of subsea tunnelling elsewhere in Norway. Examples from other parts of the world are also available, like below Stockholm, Sweden, the Inland Feeder project and Hollywood Metro both in Southern California.To take advantage of spiling rockbolts and pre-injection, it is an obvious prerequisite to be able to drill the necessary boreholes in the right positions and at the correct angle. In drill and blast excavation this is simple, but in TBM projects it has repeatedly turned out to be difficult. More than once owners have accepted bids containing reassurance from the contractor that the drilling method will be sorted out later. Experience shows that if ælaterÆ means after start of the TBM operation, it is often too late.

Jan 1, 1999

By S M. Denn

The Cawse nickel-cobalt operation is situated 50 km NW of Kalgoorlie in Western Australia, at latitude30o22'30'' south and longitude 121o08'30'' east on the Kalgoorlie 1:250 000 geological map sheet (SH 51-9) (see Figure 1). The project is owned and operated by Centaur Nickel Pty Ltd (CTR) and was the first in Australia to commercially produce nickel metal and cobalt sulphide through pressure acid leach (PAL) technology. Cawse has a total resource base (all categories of resources + reserves) of 213 million tonnes Mt at 0.7 per cent Ni and 0.04 per cent Co, comprising 127 Mt at Cawse Central which is 100 per cent owned by CTR and 86 Mt at Cawse Extended where CTR has a 80 per cent equity. Cawse Extended is located immediately to the northwest of the Cawse Central leases. All current reserves (proved and probable) of 30 Mt at 1.0 per cent nickel are contained within Cawse Central. In addition the Siberia project area 20 kilometres to the NW has a resource of 63 Mt at 0.7 per cent Ni. Cawse is a dry laterite deposit, with nickel and cobalt hosted by iron and manganese oxides. Cawse Central mineralisation extends over a ten kilometre strike length, with three pits currently being mined. The Bunyip pit has the premier nickel and cobalt grades within Cawse Central. There are seven dominant lithology types forming mappable units within current pit exposures. Four of these units are host to nickel and cobalt mineralisation. Ore types are defined as Upgrade, Grind and Non-upgrade, depending on their physical characteristics with respect to the treatment route. Mining commenced in February 1998. To the end of calender 1999 the operation has produced 2100 tonnes nickel plate and 470 tonnes of cobalt as a cobalt sulphide product. Future production will target 9000 tonnes per annum Ni metal and up to 2000 tonnes per annum Co, based on processing 500 000 tonnes of ore per annum.

Jan 1, 2000

By J Zhang, L Klemettinen, A Jokilaakso, J Biswas, J Partinen, H O’Brien, A Klemettinen

Waste lithium-ion batteries (LIBs) are important secondary sources of many valuable materials, including Critical Raw Materials (CRMs) defined by the European Union (EU): lithium, cobalt, manganese, and graphite. Additionally, LIBs typically contain nickel and copper, which are classified as Strategic Raw Materials for EU since 2023. In recent years, great effort has been made to develop efficient recycling processes for waste LIBs. Pyrometallurgical processes have been essential in industrial production of metals for many decades. These technologies are relatively mature, with high adaptability for different raw materials. Pyrometallurgical treatment in LIB recycling typically involves the use of smelting processes, in which waste batteries are heated above their melting points and metals are separated through a reduction reaction in the liquid phase. Through this recycling route, cobalt, copper, and nickel can be efficiently recovered in the form of a metal alloy, whereas lithium and manganese are lost in the slag phase. The goal of this work was to increase the recoveries of valuable battery metals through a combination of hydro- and pyrometallurgical unit operations. First, industrial Li-ion battery scrap underwent a selective sulfation roasting stage, where the aim was to transform LiCoO2 and Mn-oxides into Li, Co and Mn sulfates. After roasting, the battery scrap was leached in distilled water with a solid to liquid ratio of 100 g/L at 60°C and recovered 95 per cent of Li, 61 per cent of Mn and 35 per cent of Co. After leaching, the solid leach residue was mixed with industrial Ni-slag and biochar, followed by reduction at 1350°C in argon atmosphere. The high-temperature smelting experiments were conducted as a function of time (5–60 mins) to investigate the reduction behaviour of battery metals. The results show that Co and Ni from the slag and leach residue can be efficiently recovered in the slag cleaning stage.

Jun 19, 2024

By P Crorkan

Within the framework in which future exploitations for Codelco-Chile Divisi=n El Teniente are situated, regarding the deepening of its reserves and the geotechnical problems that affect their recovery, it becomes strategic to evolve with new variants, which make deep mining possible. Codelco ChileÆs Divisi=n El Teniente is progressing within its long-term planning the exploitation of a sector called Esmeralda, which includes its removal through the gravitational caving method (panel caving). It is planned to use pre-caving, which basically consists of developing and undermining the undercut level, without having developed the infrastructure of the production and transport levels. This is carried out in order to achieve a better redistribution of the stresses, thus obtaining higher quality in the infrastructure development of these levels as well as less risk. The extraction reserves for this area, estimated through the opportunity cost selection criteria, were determined at 348 million tons with an average grade of 1.014 per cent Cu. The project carried out geological and geotechnical studies in order to prevent the geomechanical risks of the sector to be exploited, which is a site conformed totally by primary ore. Lithologically, it occurs mainly in Andesite, located at the western limit by Brecha Braden Pipe. There are also varieties of porphyries and hydrothermal breaches of anhydrite. The Esmeralda Mine production program will increase from 4000 tpd (average) in 1998 to its 45 000 tpd rate of production estimated for the year 2005. The approved investment for the period 1995 to 1999 is $US 150 million, out of a total $US 213 million for the project. At feasibility study level and before the project, it showed a Net Present Value of $US 342 million, an Internal Rate of Return of 37 per cent and an IVAN indicator of 2.3 for a ten per cent discount rate and a copper price of 100 US cents/lb.

Jan 1, 2000

By M S. Powell

In this paper it is argued that we are entering a new mining era, based on considerably more challenging orebodies as we rapidly expand minerals production by exploiting previously uneconomic deposits. Rapidly increasing production costs cannot be sustained by continually increasing commodity prices, as illustrated by the recent downturn in the industry.Driven by reduction in grade, requiring the processing of 50 to 100 per cent more ore to recover the same amount of metal, often accompanied by finer grain structure - necessitating a finer product size and more challenging recovery - the productivity of the mining industry is dropping in real terms. The author suggests that tweaking current technologies and relying on economies of scale will not turn the industry around, but rather a switch to considerably more efficient processing is required.It is imperative to utilise the properties of the orebody, especially in terms of variability, in revolutionising our processing techniques. Our new mantra may be æselective mass mining with flexible processingÆ. This paper explores how this may be implemented using current technology and equipment in order to change the cost profile of the new mining industry. Orebody knowledge, based on the underlying process drivers, rather than proxies, is required. These properties and their variability will need to be propagated into the orebody through utilising the geological data rather than smoothing block averages, which destroys information on variability.Novel flexible circuit designs are presented that can respond to a wide variability in ore properties and throughput requirements in order to slash processing costs and energy utilisation, while enhancing overall recovery. The success of these circuits will be based on an ability to predict at both design stage and in everyday processing the variable ore properties, which is dependent upon reliable orebody knowledge that caries variability and underlying processing properties.CITATION:Powell, M S, 2013. Utilising orebody knowledge to improve comminution circuit design and energy utilisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 27-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By R C. Morris

Secondary microplaty haematite in its variety of styles and generations is the defining component of the high-grade banded iron-formation (BIF)-hosted iron ores of the world that are dominated by martite (M; - haematite pseudomorphs after magnetite). The term microplaty haematite (mplH) was introduced during the CSIRO-AMIRA 1976-1994 iron ore program, and was used to differentiate the then main export martite-microplaty haematite (M-mpl H) ore types of Tom Price-Whaleback and Paraburdoo (Paleoproterozoic), from the newly exploited, more prolific supergene martite-goethite (M-G) ores (Mesozoic-Paleocene) of the Hamersley Province that are now the major Hamersley iron ore exports.Morris (1980, 1985) suggested that the most important genetic factor that distinguishes the two main ore types was regional metamorphism of Paleoproterozoic M-G ores at temperatures normally related to diagenesis (ca 80 - 100°C). As temperatures increased, mplH grew in goethite both spontaneously as well as by nucleating on martite and other pre-existing haematite. Because the conversion of goethite to haematite involves a ~27 per cent reduction in volume, the crystals probably grew within microvoids of their own creation, with iron transfer through water resulting from the process itself, a local hydrothermal process requiring no introduced hypogene fluids.Barley et al (1999) and Taylor et al (2001) concluded instead that oxidation of introduced siderite in hydrothermally metasomatised BIF ‘protore’ resulted in mplH + ankerite by reaction with heated meteoric fl uids. This postulated ‘protore’, still preserved locally at Mt Tom Price, was described during the CSIRO-AMIRA program as local post-ore BIF metasomatic residuals. These new hypogene-meteoric concepts for M-mpl H genesis have formed the basis for a range of varying local and international models that currently dominate the literature of iron ore.No valid petrographic data supporting the hypogene-supergene modelling was found but petrographic images of goethite-related mplH growth in a range of different environments are shown.

Jul 11, 2011

By D Mather

Fibre reinforced shotcrete has long been accepted as temporary ground support in both mining and civil tunnel linings. Greater knowledge and understanding of shotcrete as an engineering material and advances in its quality have enabled designers to eliminate the requirement of a second pass lining. The initial shotcrete can be used as the permanent tunnel lining or be incorporated into the final lining design, rather than ignored and considered as sacrificial.For the initial shotcrete lining to become a suitable permanent tunnel lining it must be able to establish and maintain stability over time when subjected to all possible loads. To ensure this, best engineering practices are required during the design phase of the project to analyse; ground conditions including rock mass properties, ground and ground water quality, rock mass loadings, excavation sequencing, and construction methodologies.The increased durability of steel fibre reinforced shotcrete over traditional tunnel support, in the right ground conditions, makes it possible to achieve a serviceability design life of greater than 100 years (as required in most infrastructure projects). By specifying a good quality shotcrete mix and ensuring adequate quality control for batching, fibre dosing, preproduction testing, excavation sequencing, and application control, it is possible to eliminate the requirement of a secondary lining. The properties of a suitable permanent lining must be well established using suffi cient preproduction testing in combination with post application monitoring.A major benefit of steel fibre reinforced shotcrete in ground support applications is the removal of any requirement for workers to work under unsupported ground. Its use can also significantly reduce, if not eliminate, the manual handling associated with placing traditional reinforcement such as lattice girders and mesh. Both of these benefi ts are significant with the ever increasing focus on health and safety.This paper highlights factors that must be considered in the design and specifications to enable an initial shotcrete tunnel lining to become the permanent shotcrete tunnel lining.

Mar 8, 2011

By G Morgan, C Kemp

In December 2010, a trial of borehole radar technology was conducted to test the usefulness of the technique in better refining the position and geometry of narrow vein orebodies away from the primary data sources of drilling and mapping of development excavations. This paper summarises the reasons why the technique was applied, describes the testing methods selected and summarises the outcomes of the trial.Poor reconciliations of recovered metal from a section of an orebody at Jundee mine site, Western Australia, led to an investigation that identified insufficient understanding of the geometry of a narrow vein orebody as a potential cause. This orebody was situated between mapped development excavations and away from surrounding drill holes. Borehole radar was identified as a possible technique that could supply information on vein location and continuity away from other data sources allowing more accurate orebody modelling and subsequent stope optimisation.A borehole radar instrument (10 - 100 MHz frequency) was inserted into pairs of purpose-drilled boreholes on either side of relatively well-constrained mineralisation and the radar reflection data was collected. This process was repeated in five locations across the mine to represent the most common geological settings, lithologies and orebody varieties encountered at Jundee to determine the suitability of applying the technique in each of these settings. Collected, processed and interpreted radar data was compared to other geology data collected independently for verification and interpretation.Conclusions drawn from the analysis were that the technique could effectively determine the following features of the mineralised veins in the majority of test environments: geometry of veins, magnitude of offsets where structures intersect and orientations of planar structures with short strike length. The technique was very useful in selecting the appropriate structural interpretation where available data could lead to multiple, equally likely, interpretations.CITATION:Kemp, C and Morgan, G, 2012. Using borehole radar to refine orebody interpretations in a narrow vein gold deposit, in Proceedings Narrow Vein Mining 2012 , pp 121-130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By R Durchholz, A-J Heiertz, R Schmitz

Mining of lignite is the largest bulk materials handling activity in Europe. In order to mine this lignite, with an average calorific value of only a third of bituminous coal in an economical way, highly efficient opencast mining technology is mandatory. The total continuous mining of overburden and lignite was introduced more than 60 years ago and was subsequently developed stepwise into the largest mass transport system of the world. In 2011, the Inden Mine, one of three RWE Power mines, stripped 90 Mbcm of overburden to produce 22 Mt of lignite. In total, nearly 100 Mt of Lignite was produced from the three mines of RWE Power in Germany. Beside bucket wheel excavators (BWE), several high-performance in-pit crushing and conveying (IPCC) systems, which allow the adoption of continuous mining systems, even for typical shovel and truck (S&T) operations, are available today. RWE Power assists operators considering a change from the S&T to IPCC technology, both in the planning process involving large-scale belt conveyor systems and later with operational know how transfer. In a number of cases, the challenges associated with this system change have been addressed and solved successfully. One key challenge is managing the development of skills for operating the belt conveyor systems efficiently. This paper compares the effectiveness of S&T to different configurations of continuous mining operation for an up to 170 m deep mine with a total annual output of 117 Mbcm. From the mine operatorÆs point-of-view, the quantity and skill level of staffing required for operation and maintenance are discussed in detail. The main conclusion of this paper is the larger the operation becomes and the longer the mine life is, the earlier fully continuous mining systems should be planned and implemented.CITATION:Schmitz, R, Durchholz, R and Heiertz, A-J, 2012. Change challenges for large open pit mines, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 103-110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By D Sibthorpe

The employment of a tunnel boring machine (TBM) is the default delivery method for the realisation of traffic, utility and primary resource underground space worldwide, with hundreds of kilometres completed safely each year. This is not yet the case for the mining sector in Australia, specifically underground coal mining. The safety advantages of TBM delivery when compared to New Austrian Tunnelling Method (NATM) delivery, or that of drill and blast, remains unrealised.With coal access drifts ranging between 1000?m and 3000?m in length, the construction of these facilities using TBMs could be done in a fraction of the time when compared to current practice. TBM world records currently stand at 435?m/week or 1600?m/month for the 7.0?m to 10.0?m range. Resource owners and developers should embrace the opportunity to deliver access to their orebodies in only a few months, excluding machine assembly and disassembly time.There are challenges in utilising TBMs for construction of Coal access drifts, such as; TBMs generally being bespoke design, maximising capital efficiency for drift development, and geotechnical variances between projects. This paper explores safer and more cost-effective options. This paper also provides detail of how the configuration within a completed drift could be optimised to ensure all site specific needs are met with regard to future use of the drift. The paper also includes descriptions of the engineering solutions that are available for physical and atmospheric challenges specific to coal drift applications and how the TBM manufactures are adapting to the regulatory requirements are also covered.Due to downward pressure on high cost bases and ever increasing safety requirements the popularity of TBMs in the Australian mining sector can be expected to increase and eventually become the default delivery method for coal drift construction, building them cheaper, faster and?safer.CITATION:Sibthorpe, D, 2014. Coal drift construction by tunnel boring machine, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 671–682 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D O’Dea, B Godel, T Honeyands, G Evans, T Harvey

The pores within iron ore sinter are important for producing a high quality material that is strong and easily reduced. The complementary methods of mercury intrusion porosimetry (MIP) and X-ray computed tomography (CT) were used to characterise the structure of industrial and pilot scales sinters across a wide range of pore sizes (3 nm to 100 µm for MIP and 50 µm to 5 mm for CT). The inhomogeneous nature of sinter and the variation in the measurements make it difficult to compare samples. The generalised additive modelling (GAM) approach, using the open source statistical software package, R, has been applied to highlight where there are peaks in the concentration of pore sizes. Importantly, the shape of the GAM-fitted function and the heights of the peaks show statistically significant differences between samples. For the samples investigated, the GAM-fitted functions for the MIP volume distribution of pore diameters were found to have a common set of distinctive peaks at 0.005, 0.6 and 20 µm. The GAM approach was also applied to the X-ray CT measured pore wall thickness, highlighting a single peak whose position varies between samples. The cause of these distinctive peaks and their implications for sinter quality are discussed. Correlation was found between the volume in peak 1 (0.005 µm) and the concentration of primary hematite. No correlation was found between the pore wall thickness and the strength of the sinter, suggesting the composition of the pore walls may be more important. Future work will focus on small-scale sinters produced under tightly controlled conditions to study sinters with a wider range of quality values.CITATION:Harvey, T, O’Dea, D, Evans, G, Godel, B and Honeyands, T, 2017. Highlighting key features of the pore structure of iron ore sinter using mercury intrusion porosimetry and X-ray computed tomography, in Proceedings Iron Ore 2017, pp 39–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D Rubery, C Croker

The Boddington Gold Mine (BGM) is located 120 km south east of Perth, Western Australia. The operation is managed by Worsley Alumina Pty Ltd and mined by contractor Henry Walker Eltin (HWE). The mine has been operating since 1987 with ore extracted from a series of pits along strike. Ore is contained within the basement rock, which is overlain by a cap rock layer and transition zone. Cap rock and basement zones require blasting.As the mine neared completion, a high-grade deposit was discovered within 50 m of an existing Western Power substation and 100 m from the processing mill. The substation provides power to the Boddington area and is a back-up power supply to the city of Perth. Due to the delicate nature of the transformers located at the power station, overhead power lines and the mill, blasting in the area was considered very high risk. As such blasting needed to be controlled for flyrock, airblast and most importantly peak vibration and frequency limits which had the potential to damage the transformers.The mine was due for closure in March 2001. The decision to mine the pit was based on its high grade, ability to be blended with lowering grades from other pits and changing of the processing technique with the expansion. This decision extended the life for a further six months.Due to the high potential risks a detailed risk assessment was conducted by Orica, Worsley and Henry Walker Eltin. The completed assessment and the major design parameters were presented to Western Power for approval. The ability to reduce the blasting risk was focused on limiting of vibration through controlling maximum charge initiated per delay, blast timing and firing direction, and other innovative control measures. OricaÆs SHOTPlan« and Sabrex« computer modelling packages were used to predict the outcome of blasts.The success of this project has opened the doors for other high risk blasting projects, which otherwise may be left unmined.

Jan 1, 2002

By R A. M Maddever, P Jeanneau, V Flahaut

Over the entire life cycle of a mine, from early resource evaluation to the blasting of benches, the collection of geochemical data is crucial for the site operator, who must routinely and intensively drill and sample the orebody. This produces huge numbers of physical samples, in turn requiring significant cost and time for their preparation and assay. Moreover, despite best efforts, the sample recovery process is prone to error, which limits the quality of data.The pulsed neutron gamma technique has been used for decades in various industries, in particular oil logging, for its ability to provide direct identification and quantification of elemental concentrations. However, its implementation in logging tools for the mining sector is relatively recent. Built around the latest in technology for optimal spectrometric measurement, a commercial tool referred to as FastGrade™ 100 has been available for a few years and used with increasing success in the mining environment, specifically the iron ore industry, resulting in a reduction in the amount of collected samples. Relying on the physics of neutrons and gamma photons, both of which are particles that penetrate the surrounding bedrock through several tens of centimetres, such spectroscopy tools measure in real-time the composition of a much larger volume than the delimited volume of the drilled material traditionally used for geochemical mapping. Better statistics and reliability of the estimated composition increase the ability to properly and quickly measure drilled holes and allow the substituting of all or part of the sampling and assaying efforts by geochemical log data. Our paper focuses on this technology, known as pulsed fast and thermal neutron analysis (PFTNA). It reviews the main drivers for the design of such a logging tool and discusses how the fundamental characteristics of the technology, in terms of neutrons and gamma interactions, translate into interpretation of the analytical output.CITATION:Jeanneau, P, Flahaut, V and Maddever, R A M, 2017. Iron ore benefits from neutron pulsed geochemical tools, in Proceedings Iron Ore 2017, pp 387–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

WHEN the writer resided at Zeehan, qn the West Coast of Tasmania, some years ago, he took a keen interest in the geology of the district and availed himself of the opportunity to investigate occurrences, of the varied minerals in which the field abounds. The following notes were compiled as a result of one of his periodical visits to the outlying mining districts, when an examination was made of the bindsay Reward tin mining property, which has an area of 140 acres. This is most easily reached from Renison Bell, the centre of the North Dundas tin-fields, on the Emu Bay railway, 'about' eight miles north east of Zeehan. Thence a pack track some 14 -miles long connects with the mine, crossing the Piemah River by a fine suspension bridge.The mine itself is situated on the main south leading spot of the Parson's Hood Range, at an altitude of some 1600 ft. above sea level. The Parson's Hood Range is composed of granite and is an extension of the rugged Meredith Range. A remarkable feature is the uniform topography of the surrounding country when viewed from the peaks. Except where dissected by the rivers and creeks, the surface is practically level and, indeed, affords a striking illustration of an ancient uplifted peneplain.The mine has been opened by means of trenches and adits, and the ore-body proved to extend for a length of 30 chains, with an average width of about 100 ft. Its general trend is west-north-west, and its dip, which is steep, corresponds to that of the country-rocks. These latter, which are of sedimentary origin and generally regarded as of pre-Silurian age, have been tilted at high angles, consequent, no doubt, on the crustal movements produced by the intrusion of the huge granitic masses which now form the high ranges in the vicinity.It may be here remarked that it is not Within the scope of this paper to deal with the sequence of events leading to the geological structure...

Jan 1, 1923

By G Fahey, S Rose

"Mining geology as a defined profession is only about 100 years old. The successful modern mine geologist needs to be a multidisciplinarian, but also needs to maintain a focus on the key outputs of the role. The technical skills needed in the role have increased as mining methods move to increasingly mechanised techniques. As well as being the guardian of the orebody and ensuring minimal dilution to expected ore grades, the mine geologist should be competent in the 12-point mine geology process. The mine geology process should include:a statement of purpose (a ‘mission statement’)geological mapping/logging system that supports consistent and regular geological data collection, storage, and interpretationsampling system that can produce representative samples and fits in with the mining scheduleassay database with relevant controls to ensure only ‘clean’ data is loadedsimple quality assurance / quality control (QA/QC) system for samples and assays, with a response process to react to out of specification resultsconsistent method of exporting, visualising, processing and interpreting assay data to create mining blocksdevelopment sign-off system so that all development and stoping is controlledproduction tracking system to monitoring and reporting what ore and waste volumes have been moved from the face, to any intermediate stockpiles, the run-of-mine (ROM) pad and into the crusherreporting system for daily, weekly and monthly reporting of tonnes and gradesdocumentation so that the grade control system has simple, but effective descriptions of how it works, who has responsibilities, and authorities, and be easily maintainedreconciliation system to compare resource and reserve to grade control and to mined and milledtraining system so that the geology team can quickly become competent.In this paper, the authors discuss the requirements of each point, and comment on common shortfalls observed by them over several years’ experience on producing mines worldwide.CITATION:Rose, S and Fahey, G, 2014. Modern mining geology, in Proceedings Ninth International Mining Geology Conference 2014 , pp 461–466 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By C Noble, J Webster-Brown

A survey of selected West Coast Streams was undertaken in Summer 2001, Summer 2002 and Winter 2002 to establish the degree of arsenic (As) contamination in waters and sediments downstream of old coal and gold mine workings on the West Coast. Of the catchments studied, Soldiers/Ford Creek and Rapid Stream showed the most significant elevated As concentrations, predominantly in dissolved form, and evidence of AMD or ARD contamination (high sulfate concentrations and/or acidity). The rate and processes of removal of dissolved arsenic from the water column (attenuation) have been studied in these catchments. The Rapid Stream and Soldiers/Ford Creek catchments are directly affected by adit drainage from the Sullivan and Blackball coal mines respectively. Both catchments have high As concentrations in the sediments, with up to 770 mg/kg in Soldiers Creek and 490 mg/kg in Rapid Stream. Dissolved As concentrations are significantly elevated in the neutral pH waters of Soldiers Creek; typically as high as 100 - 200 ¦g/kg, up to 500 m downstream of the main adit discharge (800 ¦g/kg As). Adit inflows to Rapid Stream were acidic and contained 20 - 30 ¦g/kg dissolved As, with relatively high concentrations of arsenic in the stream water in winter (up to 18 ¦g/kg), but not in summer. Analysis of concentration trends and As:SO4 ratios downstream of these obvious As sources confirmed that dissolved As had been actively removed from the water column, but varied seasonally with greater removal evident in summer. Adsorption of arsenic onto iron oxide in the stream sediments is the most likely mechanism of removal. The Snowy River catchment, on the other hand, has relatively high As concentrations in both the sediments and the water column, but there was little evidence of a distinct AMD or ARD input from the Blackwater gold mining area. Preliminary investigation suggests that dilution rather than attenuation is responsible for decreasing As concentrations downstream.

Jan 1, 2003

By Y Sha

During the last two decades, China has expanded its iron and steel industry very quickly, from less than 100 Mt/a steel production to over 700 Mt/a. It caused big increases in both domestic iron ore production and imported iron ore quantities year by year. The mode of iron ore supply has changed from almost all domestic supply to major tonnes of imported ore plus domestic ore supply. Over 200 blast furnaces with volumes larger than 1000 m3 each have been built and put into operation. Sinter machines have been enlarged quickly. There are now 135 sinter machines with =200 m2 sintering area each. Pellet production increased from 11.94 Mt in 1999 to 210 Mt in 2011, resulting from rapidly increasing domestic concentrate supply and rapid development of the grate-kiln process. The typical ferrous burden constitution is high basicity sinter plus pellets plus lump. The pellet proportion increased and the sinter proportion decreased gradually. A lot of technical improvements, like deep bed sintering, sintering with a high ratio of limonite, composite sintering, pellet process optimisation, a high ratio of hematite in pelletisation, blast furnace operation with low-grade ferrous burdens and hazardous element control, etc have been made to enhance iron burden quality and to reduce hot metal cost. Chinese iron and steel production is expected to increase slightly in the next few years. Its overcapacity should be controlled effectively. Given the variations of iron ore supply, pellet production will keep progressing in terms of production scale and pellet quality, the sintering process will be improved further by various measures to utilise different ores efficiently, and ferrous burden constitution will be optimised continuously to realise the lowest cost of hot metal production.CITATION:Sha, Y and Wang, Z, 2013. The Chinese iron and steel industry response to the challenges of iron ore supply, in Proceedings Iron Ore 2013 , pp 7-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013