Search Documents

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Mar. 10 to Apr. 10, 1915: Oscar Lachmund, Greenwood, B. C. Harvey B. Small, Mangaugue, Colombia. S. W. Ough, Pachuca, Mexico. M. F. Sayre, Schenectady, N. Y. B. W. Vallat, Detroit, Mich. James W. Hambleton, Parral, Mexico. Charles Mentzel, New York, N. I . Philip L. Gill, Woodmere, L. I., N. 1. M. K. Rodgers, San Francisco, Cal. John T. Fuller is President of the F. Shepherd Mining Co., operating at Rush Mountain, Ark.

Jan 5, 1915

AARONS, J. BOYD, Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th -Reserve Engineers. BAINS, THOMAS M., Major, Engineer Officers' Reserve Corps. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy Supt. (Captain), New York State Troopers; Captain, 22d Regiment, N. Y. N. G. BARLING, H. B., Ist Lieutenant', Engineer Officers' Reserve Corps. BIGELOW, BRAXTON. BLOOMFIELD, E. C., Lieutenant. , BORROW, F. K. BROCK, R. W., Major, 19th Reserve Battalion of Canadians. BROOKS, ALFRED H., Captain, Engineer Officers' Reserve Corps. BROWNE, DE COURCY, 1st Lieutenant, Ordnance Dept., Fortress Monroe, Va.

Jan 9, 1917

By Magnus Troilius

The method of using the bromine process of determining sulphur in steel, described below, is in successful use at the Midvale Steel Works. Ten grams of drillings are weighed out and put into the 1/2-liter flask A, with long neck. The flask is connected with a wide glass tube C', which, in its turn, is connected with the absorption bulbs B, containing HCI, 1.12 specific gravity, and ahout 5 C.C. of bromine. The wide tnbe C causes the vapor to condense and flow back into the flask A during boiling. The bulbs B connect with a long glass tnbe, which may be made to carry off the bromine fumes through a hole in a window, or, better still, through a flue with powerful draught. The connections being made, 100 C.C. of boiling water are run in through the thistle tube T. The air is thus completely driven out of the flask. 100 C.C. of HC1 (about 1.19 specific gravity) are then run in. When the gas begins to run rattler slowly through B, heat is applied until boiling gradually ensues. The steel being completely dissolved, the apparatus is disconnected, and the contents of B rinsed out into a beaker of 100 C.C. capacity, into which a few C.C. of a concentrated solution of BaCI, have been previously introduced. Heat is then applied (best by means of the hot iron plate) until the bromine is completely driven off and the BaSO, has settled nicely to the bottom. The BaSO4, is then filtered off on a small

Jan 1, 1884

By J. J. Oberly

WHILE examining lineage boundaries in germanium single crystals as described by Vogel et al.,&apos; patterns of conical etch pits were noted which reveal interesting properties of dislocations. The crystals were grown by pulling in the <100> direction, and (100) surfaces perpendicular to the growth direction were etched 4 min in a mixture of 6 cu cm HF, 10 cu cm HNO3, 6 cu cm acetic acid, 3 drops Br,. Lineage boundaries extended in any direction, but favored the <110> direction. The patterns which were noted first were composed of two or three etch pits arranged symmetrically about the lineage boundary, so that the doublets were spaced equally on either side of the boundary line and the triplets had their center pit on the boundary line. The triplets occurred less often than did the doublets; occasionally combinations were found. Two such combination patterns are shown in Figs. 1 and 2. The orientation of the patterns was determined approximately by subsequently etching the same surfaces in a mixture of 5 cu cm HF, 5 cu cm super-0x01, and 20 cu cm distilled water which produced nearby random square etch pits having edges in the <110> direction. In all cases, the axis of symmetry was <110>, being parallel to the etch-pit edges. Several successive lapping and etching operations showed that the patterns tended to continue through the crystal in the <100> direction, but eventually changed or vanished. It can be seen in both photographs that the pits in the patterns are much further apart than the pits in the adjacent section of the lineage boundary. In Fig. 1, the 10 pits of the pat-

Jan 1, 1955

By J. J. Kramer, K. Foster

The orientation distribution of surface-energy -induced secondary recrystallized grains was determined. This work was conducted on thin sheets of a 3 pct Si-Fe alloy annealed under environmental conditions that furor grouth of grains with a (100) plane in the surface of the sheet. The texture was found to be extremely sharp and almost independent of sheet thickness. The distribution varied exponentially with the angular deviation from the {100} plane. It was possible to relate the distribution to the nu-cleation rate of the secondary rains as influenced by the surface-energy difference. THE role of surface energy in the secondary grain growth of cube-oriented grains (grains with a (100) plane in the plane of the sheet) in thin Si-Fe sheets has been previously discussed.1-4 In high-purity sheet material normal grain growth usually occurs until the grains have extended through the sheet. Further grain growth is inhibited by the thermal grooving of the boundaries at the sheet surface. However, additional growth of cube grains can occur by a secondary grain growth process under conditions where the (100) plane has a lower surface energy than other orientations. Apparently for these alloys, cusps exist in the polar plot5 of surface free energy with the lowest cusp energy occurring at the (100) orientations. This has been reported to be the result of preferential adsorption of sulfur on the (100) planes.6 As a result of this process, a distribution of orientations could arise from two possible mechanisms. First, when a cusp is present in the polar plot of surface free energy, there are orientations inside the cusp that have a lower surface energy than elsewhere on the polar plot. Also, at sufficiently high temperatures, flat surfaces whose orientations are inside or just outside the cusp (depending on its shape) can often thermally etch, yielding a microscopically stepped surface of even lower surface energy. As a result, grains oriented close to cube would also have a lower surface free energy, either because of the cusp shape or by thermal etching, and could possibly grow as secondary grains by the surface-energy phenomenon. One should thus observe a distribution in the surface orientation of the cube grains comprising the secondary structure. It is the purpose of this paper to investigate this orientation distribution experimentally and to discuss the factors involved in its formation. For this purpose, the surface orientations of a large number of secondary grains in various sheet thickness were determined by means of the Laue back-reflection X-ray technique. PROCEDURE A vacuum-melted 3 pct Si-Fe alloy containing a nominal impurity content of 0.005 wt pct was processed into strip. A single cold-rolling step of 90 pct reduction was used for each strip regardless of the final sheet thickness. Final strip thicknesses of 0.60, 0.30, 0.15, and 0.075 mm were used. Care was taken to insure that the final strip surface was smooth and flat. All strips of a given thickness were annealed together at 1200°C in dry hydrogen (dew point -70°C) to develop the desired secondary structure and to insure identical environmental annealing conditions. The annealing time was selected to develop a complete secondary structure in the thinner sheets but to permit the thicker sheets (0.60 mm) to have residual primary grains remaining. This was necessary to determine whether growth impingement could lead to one secondary grain consuming another at a greater angular deviation. For the X-ray determination of the surface orientation of the secondary grains, a special specimen holder was used. The camera and holder arrangement could be aligned by X-raying a grain in three positions rotated 180 deg to each other. Thus, with a small beam X-ray focus (1 mm), the surface orientation of any grain could be determined to within one-half a degree. The surface orientations of one hundred cube secondary grains were determined for each sheet thickness. The criteria of a secondary grain were its size relative to the sheet thickness and the number of sides of the grain observed in the sheet surface. (A primary recrystallized grain extending through a sheet will generally have six edges visible in the plane of the sheet, whereas a secondary grain will have many more when growing entirely into primary grains.) Grains were selected as randomly as possible by X-raying every secondary grain found along a line drawn on the strip. No attempt was made to determine the exact orientation of the planes of the surface, as many strips from randomly selected sheets were used. On1y the angular deviation of the surface plane from {100} was measured. In order to assess the volume distribution in the

Jan 1, 1965

By H. L. Bilhartz, H. F. Dunlap, C. R. Bailey, Ellis Shuler

Data are presented which indicate that the saturation exponent, n, in the equation, R. = R100S-11, relating core resistivity, I:,. to the resistivity at 100 per cent saturation. R100. and to the saturation, S. may vary appreciably from the value of two which is usually assumed for this exponent when interpret ing well logs. Values ranging from one to two and one-half have been found on (.ore sample investigated to date. Attempts to correlate this saturation exponent with porosity or permeability of the core have not been successful. The saturation exponent is apparently not a function of the interfacial tension between the brine and the displacing fluid. Some evidence is given indicating that the resistance of the core is not a unique function of the saturation but depends upon the manner in which this saturation was achieved. Equipment and technique are discussed for measurement of resistivities in core plugs in which water saturation can be varied. lNTRODUCTION A number of investigations of the resistivity-saturation relationship for un-c~~nsolidated sands and consolidated (.ore samples have been reported in the literature. According to most of these: R. = R¹ººS², where R² = the resistivity of a formation at saturation S, and R¹ºº= the resistivity of the formation at 100 per cent water saturation. Much of this work was (lone on unconsolidated sands desaturated by gas or oil. Hen-clerson and Ynster worked exclusively with dynamic systems, flowing oil or gas through consolidated cores. There is some doubt as to how well this reproduces static reservoir conditions. Jakosky and Hopper³ onsidered also the case of consolidated core plugs, but the oil-water distribution in the emulsions which they used to saturate their cores is almost certainly different from that occurring in reservoirs. Recently Guyod quotes the results of some Russian work which indicates that n may vary from 1.7 to 4.3. No experimental details of this work are available. In connection with electric log interpretation it is important to know the value of the saturation exponent. For example, if in a given reservoir it is found that the resistivity is three time.; the resistivity observed when the reservoir is 100 pel. cent &apos;saturated with water, this fact would be interpreted as indicating a water saturation of 33 per cent if the saturation exponent were 1 and a water saturation of 6-1 per cent if the saturation exponent were 2.5. EXPERIMENTAL METHOD In the work to be described it was assumed that reservoir conditions are most nearly obtained when core plugs are desaturated by the capillary pressure technique referred to in numerous places in the literature, as for example. in Bruce and Welge&apos;s paper.&apos; In this technique the core. saturated 100 per cent with brine, is placed in contact with a ceramic disc permeable to brine but not to the displacing medium for the displacement pressures used. Pres-ure is then applied to the displacing medium and brine forced out of the core through the ceramic disc. Fig. 1 shows the core plug in place in the cell in which resistivity and saturation measurements are made. Fig. 2 shows the schematic electrical diagram wed to make resistivity measurements on the core plug. A four-electrode type circuit is used, employing a Hewlett-Packard model 400A. AC vacnum tube voltmeter. The 60-cycle AC current througli the core is adjusted to 1 milliampere and measured by noting the voltage drop across the calibrated 100-ohm resistor. The vo1tages appearing at probes 1, 2, 3, and 4 are then successively measured. Voltage drops across the top, center, and bottom portions of the core are obtained by sublracting the voltages appearing at successive probes. This technique avoids any polarization or other high contact resistance phenomena which may develop at the current input electrodes. Resistances which may develop between the core and the probes, and which are small compared to the 1-megoam input impedance 01&apos; the vacuum tube voltmeter will (obviously not affect the measurements allpreciably. Any very appreciable resistallces which may develop at any of the probe wires are detected and allowed for by inserting a 1-megohm resistor in series with the voltage measuring probe. If the probe resistance is actually zero, the new voltage measured after insertion of the I-megolim resistor will be approximately one-half of that previously measured. since the input impedance of the vacuum tube voltmeter is itself 1 megohm. If an! appreciable probe resistance has developed, the new voltage is found to be appreciably greater than one-half of the previously measured voltage. Such probe resistance; have been found to develop only occasionally and usually can be traced to poor connections betwern the core

Jan 1, 1949

By C. R. Bailey, H. F. Dunlap, Ellis Shuler, H. L. Bilhartz

Data are presented which indicate that the saturation exponent, n, in the equation, R. = R100S-11, relating core resistivity, I:,. to the resistivity at 100 per cent saturation. R100. and to the saturation, S. may vary appreciably from the value of two which is usually assumed for this exponent when interpret ing well logs. Values ranging from one to two and one-half have been found on (.ore sample investigated to date. Attempts to correlate this saturation exponent with porosity or permeability of the core have not been successful. The saturation exponent is apparently not a function of the interfacial tension between the brine and the displacing fluid. Some evidence is given indicating that the resistance of the core is not a unique function of the saturation but depends upon the manner in which this saturation was achieved. Equipment and technique are discussed for measurement of resistivities in core plugs in which water saturation can be varied. lNTRODUCTION A number of investigations of the resistivity-saturation relationship for un-c~~nsolidated sands and consolidated (.ore samples have been reported in the literature. According to most of these: R. = R¹ººS², where R² = the resistivity of a formation at saturation S, and R¹ºº= the resistivity of the formation at 100 per cent water saturation. Much of this work was (lone on unconsolidated sands desaturated by gas or oil. Hen-clerson and Ynster worked exclusively with dynamic systems, flowing oil or gas through consolidated cores. There is some doubt as to how well this reproduces static reservoir conditions. Jakosky and Hopper³ onsidered also the case of consolidated core plugs, but the oil-water distribution in the emulsions which they used to saturate their cores is almost certainly different from that occurring in reservoirs. Recently Guyod quotes the results of some Russian work which indicates that n may vary from 1.7 to 4.3. No experimental details of this work are available. In connection with electric log interpretation it is important to know the value of the saturation exponent. For example, if in a given reservoir it is found that the resistivity is three time.; the resistivity observed when the reservoir is 100 pel. cent &apos;saturated with water, this fact would be interpreted as indicating a water saturation of 33 per cent if the saturation exponent were 1 and a water saturation of 6-1 per cent if the saturation exponent were 2.5. EXPERIMENTAL METHOD In the work to be described it was assumed that reservoir conditions are most nearly obtained when core plugs are desaturated by the capillary pressure technique referred to in numerous places in the literature, as for example. in Bruce and Welge&apos;s paper.&apos; In this technique the core. saturated 100 per cent with brine, is placed in contact with a ceramic disc permeable to brine but not to the displacing medium for the displacement pressures used. Pres-ure is then applied to the displacing medium and brine forced out of the core through the ceramic disc. Fig. 1 shows the core plug in place in the cell in which resistivity and saturation measurements are made. Fig. 2 shows the schematic electrical diagram wed to make resistivity measurements on the core plug. A four-electrode type circuit is used, employing a Hewlett-Packard model 400A. AC vacnum tube voltmeter. The 60-cycle AC current througli the core is adjusted to 1 milliampere and measured by noting the voltage drop across the calibrated 100-ohm resistor. The vo1tages appearing at probes 1, 2, 3, and 4 are then successively measured. Voltage drops across the top, center, and bottom portions of the core are obtained by sublracting the voltages appearing at successive probes. This technique avoids any polarization or other high contact resistance phenomena which may develop at the current input electrodes. Resistances which may develop between the core and the probes, and which are small compared to the 1-megoam input impedance 01&apos; the vacuum tube voltmeter will (obviously not affect the measurements allpreciably. Any very appreciable resistallces which may develop at any of the probe wires are detected and allowed for by inserting a 1-megohm resistor in series with the voltage measuring probe. If the probe resistance is actually zero, the new voltage measured after insertion of the I-megolim resistor will be approximately one-half of that previously measured. since the input impedance of the vacuum tube voltmeter is itself 1 megohm. If an! appreciable probe resistance has developed, the new voltage is found to be appreciably greater than one-half of the previously measured voltage. Such probe resistance; have been found to develop only occasionally and usually can be traced to poor connections betwern the core

Jan 1, 1949

[SWEETSER, R. H.: Discussions: on Evaluation of Coal for Blast furnace Coke, 94, 378, 394,385 on Mt. Union Sand Flotation Plant for Preparing Bituminous Coal, 74, 591 on Need for Research in Foundry Pig Iron, 76, 450 on Pig Iron Low in Total Carbon, Is in Demand for Use in Various Industries 75,471 on Properties of Coal Which Affect Its Use in the Ceramic Industry, 101, 254 on Relation of Ash Composition to the Uses of Coal, 74, 471 on Research on Blastfurnace Slags 100, 137.138 on Selection of Coals for the Manufacture of Coke, 74, 637 on Sinter in Blast-furnace Burdens, 100, 54 on Sintering Limonitic Iron Ores at Ironton, Minnesota, 90, 355, 356 on Slag Control in the Making of Iron and Steel, 116, 104, 115, 116 on Solubility of Nitrogen in Liquid Iron, 116, 193, 194 on A Statistical Analysis of Blast-furnace Data, 96, 70]

Jan 1, 1936

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 331/3 Per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches.

Jan 1, 1947

By Robert C. Edmiston

The measurement of temperatures in exploratory drill holes yields information on regional and local geothermal gradients and mean surface temperatures. This data may be beneficial to the mining geologist interested in the occurrence and oxidation of metallic sulfide minerals or to the mining engineer interested in subsurface temperatures or water movement. Additionally, the estimation of mean surface temperatures by the projection of thermal gradients to the ground surface provides data on which to evaluate infrared imagery as an exploration tool. Temperature measurements in 30 diamond drill holes in the Silver Bell mining district of Arizona show that a regional geothermal gradient of 2.45°C per 100 m increases to 3.03°C per 100 m near the ground surface. It is also found that an anomaly in the mean annual surface temperature of 0.5°C is associated with the shallow occurrence of disseminated sulfides. Changes in the geothermal gradient due to topography, water circulation, and formation changes also occur.

Jan 1, 1976

By W. C. Dickerman, J. F. Thornton

TOTAL global war is making extraordinary demands on the oil industry. Huge quantities of 100-octane gasoline, extreme service lubes, toluene and other miscellaneous products are required. 100-octane gasoline is blended from isopentane, base stock, and alkylate. Isopentane is fractionated from natural or refinery gasoline; but since only limited quantities of base stock can be made in this way, catalytic cracking is rapidly becoming the major source of base stock. Alkylate, the most important component, is synthesized from isobutane and an olefin. Extraordinary demands are forcing the full utilization of all present sources and the development of new supplies of feed stocks. Fortunately, the United States finds itself with well-developed processes already available, and this is true of the manufacture of lubricating oil as well. Toluene is now being produced by new methods from special cuts fractionated from selected crudes or from catalytically processed naphthas. Designers of refinery equipment are modifying past practices to conserve every bit of material possible.

Jan 1, 1942

By R. P. Smith

THE carbon content of iron-silicon and of iron-manganese alloys at fixed activities of carbon has been reported previously.&apos; It seemed desirable to investigate a system which allows a more extended range of alloy composition within a single phase region. The iron-nickel system is ideal in this respect, in that all alloys from 100 pct Fe to 100 pct Ni are face centered cubic ("austenitic") at 1000 °C. The experimental procedure was similar to that previously described.1,2 The alloys, in the form of pieces about 2 by 2 by 0.2 cm thick, together with a similar specimen of pure iron, were equilibrated with each of a series carbon monoxide-carbon dioxide tnixtures of fixed composition, quenched in the carburizing gas in the top of the furnace and then analyzed for carbon. The carbon content of samples containing more than 0.3 wt pct C was determined by the usual combustion method; those with less carbon

Jan 1, 1961

By D. E. Moore

The strength of a natural serpentinite gouge was measured at 400°C and an effective pressure of 100 MPa. The strength of the gouge decreased with increasing pore pressure to 50 MPa and then was nearly constant between 50 and 125 MPa. The samples at 50-125 MPa pore pressure slid stably, whereas those at 3-25 MPa pore pressure showed stick-slip behavior. Lengthening the pre-heating time to 72,000 s of samples at 100 MPa pore pressure led to increases in both the strength and the likelihood of sliding unstably. With still longer pre-heating times, the strengths decreased again and sliding once more became stable. The strength of the gouge at 3 MPa pore pressure was unaffected by changes in pre-heating time. A possible explanation for the results is that excess pore pressures are being generated in the gouge, causing the true effective pressure to be lower than the apparent value.

Jan 1, 1984

By E. H. Crabtree

IN an ideal mill, with perfect milling operations, the mineral extraction would be 100 per cent, the, concentrate would be 100 per cent mineral, the tailing would assay zer.0 mineral and the milling cost would be zero dollars. Such an operation can, of course, never be attained. We can only strive to approach it as nearly as possible and in doing so most recognize .the fact that the three primary factors in milling: assay of concentrate, assay of tailing, and cost of operation bear a definite economic relationship to each other. This relation will change from time to time and will be different for different mills, depending on milling equipment, character and quality of feed, market conditions, and other factors. It is granted that for a given operation there is an economic point, but the location of this point is difficult. It is for the purpose of making some of these economic points a little more tangible that this paper has been prepared.

Jan 1, 1930

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 331/3 Per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches.

Jan 1, 1947

By A. K. Chakravarti, A. Lihiri, G. G. Sarkar

One primary objective of India&apos;s third Five Year Plan is the expansion of coal production. The goal: boost present output of 45 million tons to 95 million tons by 1965--an increase of more than 100 pct!

Jan 7, 1961

FIGURES covering appropriations recommended by the Budget Bureau for the Bureau of Mines at Washington for next year are now available and are as quoted below. APPROPRIATION BUDGET APPROPRIATION 1928 1929 General Expenses $ 86,000` $ 86,000 Investigating Mine Accidents 386,470 399,470 Mining Investigations in Alaska.. 10,860 10,860 Operating Mine Rescue Cars and Stations 327,630 342,630 Testing Fuel 154,000 158,500 Mineral Mining Investigations.... 99,570 125,000 Oil, Gas and Oil-Shale Investiga- tions 198,260 198,260 Oil-Shale Investigations 5,000 80,000 Expenses Mining Experiment Sta- tions 173,000 173,000 Care, etc., Buildings and Grounds, Pittsburgh, Pa 71,360 76,360 Maintenance and Operation, Fuel Yards Balance Balance Helium Investigations :.... 75,000 75,000 Helium Production and Conserva- tion 1,063,000 462.000 Potash Investigations 100,000 100,000 Economics of Mineral Industries. . 225,000 275,000 Totals $2,975,150 $2,562,080

Jan 1, 1928

By Frederick T. Williams

THE purpose of this paper is to discuss the relative merits of the large 31/8 in. machine and the small 21/4-in. tappett machine in driving development-headings ; and although the . data here presented were obtained from cross-cut headings alone, experience has shown that the results are equally true in drifting, raising and winning. Recently we drove two parallel cross-cuts through the same formation, using a 3k-in. machine at the breast of one cross-cut., and a 2k-in. machine of the same make at the breast of the other. The results of this work afforded an ideal comparison, since in both cases the headings were advanced through rock practically of the same hardness and breaking-properties ; the amount of sludging was equal, and there was no difference in the condition of the steel or the machines, in the air-pressure or in the experience of the operating-crews. Some operators in the Cripple Creek district contend that there is ground which cannot be handled with the small machine, the holes being too small to contain enough powder to pull the ground, etc. The results obtained in working the property of the Portland Gold Mining Co., however, show that the ground worked by them does not fall in this class. During a period of two years there have been driven, with the small machine, 4 miles and 308 ft. of development-headings, through a diversity of ground, including Pike&apos;s Peak granite (a coarsely porphyritic type of granite), highly indurated, andesitic or phonolytic breccia, true massive andesite, trachytic phonolyte, tuffas, and along dikes of decomposed basalt and hard phonolyte; in every instance a satisfactory record was made. The headings here described were driven through highly indurated, andesitic breccia, having a hardness of from 5.2 to 7.2

Mar 1, 1906

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By Gordon E. Agar

Several correlations have been proposed to relate energy consumption and size reduction in comminution, and although these are arrived at from different starting points, it is postulated that they are all statements of the same basic concept. To test this postulate, the dry ball mill grindability of langbeinite was determined, and the results were analyzed according to the various methods. An examination &apos; of the energy-particle size relationships proposed in the recent past revealed that they had much in common. In fact, the conclusion was tentatively drawn that these expressions were essentially the same, even though they were arrived at from quite different basic premises. The equations attributed to Charles2 and Holmes3 were shown to re- duce to the same single equation, W - A K-3, and the simulated continuous test used by Maxson et al.4 was shown to give the best experimental value of the required empirical parameter, ß. Furthermore, the size distribution parameter a in the Schuhmann equation, y - (x/K)2, was shown to be equal to ß in many cases. The kinetic approach used by Arbiter and Bhrany5 should give the same results as the Maxson test procedure; however, the batch operation used by Arbiter and Bhrany could not produce data that would be as precise as the simulated continuous technique. To test the validity of these conclusions, the simulated continuous method was used to obtain data on the dry grinding of langbeinite. The results are discussed in terms of the various equations and approaches. APPARATUS AND MATERIAL A ball mill with internal dimensions of 17.5 cm (6 7/8 in.) in length by 19.4 cm (7 5/8 in.) in diam was loaded to 50% of its volume with balls 3.2 cm in

Jan 1, 1969