Search Documents

By S. E. Clay

In the chemical reaction control regime employed in the laboratory dissolution experiments, calcined trona ore dissolves in aqueous solutions according to a first order, irreversible reaction rate. The study showed that the reaction is first order with respect to solution NagCO3 concentration. The activation energy was determined to be 20.233 kJ/g. mol with a rate constant equal to 1235 mm/s (2917 in. per min). The dissolving particle may be described by shrinking particle behavior.

Jan 1, 1986

[Alphabetic Section: The letter immediately following a member's name indicates grade: M-member, A-associate, J-junior. The numerals following member's grade indicate year of election. The letter following year of election indicates primary divisional affiliation: A. Mining & Exploration F. Coal B. Minerals Beneficiation G. Petroleum C. Iron and Steel H. Industrial Minerals D. Extractive Metallurgy J. Council of Education E. Institute of Metals K. Council of Economics Geographic Section: An asterisk (*) preceding a member's name indicates availability for consulting work:]

Jan 1, 1961

New York L. W. FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. WILLIAM A. POMEROY. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia FRANK A. ROSS Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 3, 1915

AARONS, J. BOYD, Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th Reserve Engineers. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy Supt. (Captain), New York State Troopers; Captain, 22d Regiment, N. Y. N. G. BARLING, H. B., 1st Lieutenant, Engineer Officers' Reserve Corps. BIGELOW, BRAXTON. BLOOMFIELD, E. C., Lieutenant. BORROW, F. K. BROOKS, ALFRED H., Captain, Engineer Officers' Reserve Corps. BROWNE, DE Courser, 1st Lieutenant, Ordnance Dept., Fortress Monroe, Va.

Jan 8, 1917

By Stefan S. Kapusniak, Nichol Riggott, Stephen F. Smith

Stability investigations have been carried out in a number of major coal mining tunnels in the U.K. using various instrumentatcon techniques. The paper describes these instrumentation methods and presents results from studies in several tunnels. Both long and short term stability aspects are discussed. Prediction of tunnel stability is examined in relation to tunnel support requirements. Computer simulation techniques are used along with actual underground measurements to identify tunnel design parameters for influencing choice of support and prediction of long term stability.

Jan 1, 1984

By L. D. Jaffe, R. K. Pitler

IT would clearly be advantageous to produce molten titanium, suitable for alloying and casting, directly from the relatively inexpensive tetra-chloride, without using a metallic reducing agent. Accordingly, a preliminary investigation has been made of the production of titanium by hydrogen reduction of the tetrachloride in an electric arc furnace. For the reaction: TiCl4(g) + 2H2(g) ? Ti(s) + 4HCl(g), Lockhart and his colleagues' have calculated equilibrium constants at 800" to 1500°K, based on tables of Brewer.' Extrapolating these data on the assumption that the heat of reaction varies linearly with temperature, and using Brewer's value for the heat of fusion, there is obtained for the reaction: TiCl4(g) + 2H2(g) ? Ti(l) + 4HCl(g) an equilibrium constant at 2100°K (100" above the melting point) Kp = (PHCl)4/pTlcl4 (Ph2)2 = 0.167 atm. If this is correct, starting with hydrogen saturated with TiC14 at 25°C, where the vapor pressure of the latter3 is 12.6 mm, and maintaining the overall pressure at 1 atm, 99 1/4 pct of the TiC14 would be reduced to Ti at equilibrium. An arc furnace designed for the melting of titanium and lined with water-cooled copper was used for the preliminary experimental check. Its inside diameter was 2 7/16 in. and height 6 in. The water-cooled electrode was tipped with 3/4 in. diam tung-sten. In the one run carried out, the furnace was charged with a starting batch of 293.35 g of scrap titanium,' analyzing 99.24 pct Ti. After the system was twice pumped out and flushed with argon to remove air, the arc was struck in argon and kept at 400 amp dc, electrode negative, for 1 min to melt the starting batch. Commercial tank hydrogen, dried by passing over silica gel and bubbled through technical grade TiC14 at room temperature, was then admitted to the furnace. The inlet tube directed this gas downward toward the arc and melt; the gas outlet was at the top of the furnace. The quantity of gas passed through was not measured accurately but is estimated to be about 50 liters per min at a few mm of mercury above atmospheric pressure. The arc was held in the H2-TiC14 mixture at 400 amp with little difficulty. After 10 min the arc burned through the copper lining above the melt, admitting water and ending the run. (This had happened frequently in straight melting runs under argon, and is not thought due to the atmosphere used.) In the furnace were found an ingot, several small pieces, and a little metallic powder, evidently formed when water entered the hot furnace. Some titanium also clung to the electrode. The portions were weighed and separately analyzed for titanium. Their total weight was 321.76 g of 94.82 pct overall purity. Much of the impurity consisted of tungsten broken off when the titanium was removed from the electrode. No detailed impurity analysis was made because the starting materials were impure and flooding the furnace introduced further contamination. Thus, the metal recovered contained 305.08 g Ti, as compared to 291.12 g in the starting batch. Titanium could not have been carried over from previous melting runs in the furnace, as the interior was sandblasted and the electrode ground clean before the run. Evidently at least 13.96 g of Ti were produced from TiCl4. Since this would require complete reduction of 430 liters of TiCl, gas at 12.6 mm of Hg, the efficiency of the process must have been rather high. Experimental work is continuing. No reason is seen why the process could not be scaled up to the size of a 30-ton steel-melting arc furnace. In a large unit there would be a large molten pool from which liquid metal could be withdrawn for alloying and casting. The problems of electrodes and power supply are similar to those arising in arc furnaces for melting titanium. Unreacted TiC14 and the HC1 in the exhaust gases could be recovered; unreacted H2 could be dried and re-used. The melt would be saturated with hydrogen, whose solubility in liquid titanium is unknown. Small amounts of hydrogen seem to have little effect on the properties of titanium.5 If the amount introduced was so large as to impair properties or cause casting difficulties, it could be reduced by holding the melt under an inert gas or by pumping on it, prior to casting. Acknowledgment The authors would like to thank I. Preble and M. Goldman for their valuable aid in the experimental work and the thermodynamic calculations, respectively. References 1R. J. Lockhart, J. J. Ward, M. J. Hussey, and J. W. Clegg: In unpublished report, "U. S. Air Force Project Rand. Titanium and Titanium Base Alloys." Battelle Memorial Institute (1949) 37-44. 2 L. Brewer et al: Chemistry and Metallurgy of Miscellaneous Materials—Thermodynamics. Ed. by L. L. Quill. pp 13-39, 60-192. (1950). McGraw-Hill Book Co. 3 K. Arii: Scientific Reports. Tohoku Imp. Univ. (1933) 22, 182. 4 R. S. Dean, J. R. Long, F. S. Wartman, and E. L. Anderson: Transactions AIME (1946) 166, 369-381; Metals Technology (Feb. 1946) TP 1961E. * R. I. Jaffee and I. E. Campbell: Transactions AIME (1949) 185, 646-654; Journal of Metals (Sept. 1949) TP 26813.

Jan 1, 1951

By R. R. Vandervoort, W. L. Barmore

Tensile creep experiments were conducted on high-purity, poly cvystalline rhenium from 1500" to 2300°C at stresses from 1500 to I0,OOO psi in a vacuum of 10-a torr. The apparent activation energy for creep was 60 kcal per mole, and the steady-state creep rate varied directly with stress to the 3.4 power. Dislocation substructure that developed during creep was studied by transmission electron microscopy. Possible rate-controlling deformation mechanisms are discussed. The creep behavior of most metals at elevated temperature can be represented by the following equation:&apos;&apos;&apos; t = Cf(s)(^)(s/E)nD [1] where i = steady-state creep rate, C = constant, f(s) = a function involving microstructure, s = applied stress, E = the average elastic modulus at test temperature, n = constant, D = diffusion coefficient According to this well-established relationship, metals with higher elastic moduli and lower diffusion coefficients should have greater creep resistance at the same stress and temperature and equivalent mi-crostructures. While no diffusion data are available, the diffusivity of rhenium should be less than that for most other refractory metals because of its high melting point and hcp crystal structure. The Sherby-Simnad relation for calculating atomic mobility in metallic systems3 predicts that the diffusion coefficient for rhenium is less than that experimentally determined for tungsten4 in the temperature region 1500. to 2200°C. At these temperatures the elastic modulus for tungsten5 is only slightly larger than the extrapolated modulus for rhenium.6 Thus, rhenium is a good possibility for a a high-temperature structural material, but few data on the creep of rhenium have been reported. This investigation was undertaken to study the high-tempera-ture deformation behavior of rhenium in detail. EXPERIMENTAL TECHNIQUES The material used in this study was consolidated from high-purity powder. After cold pressing the powder to a plate a in. thick, the billet was sintered in hydrogen at 2250°C for 24 hr. The plate was reduced to 0.100 in. by cold cross rolling with intermediate anneals at 1650°C for 20 min between passes. The plate was further reduced to 0.060 in. by unidirectional cold rolling with similar heat treatments between passes, and then finally stress-relieved in hydrogen at 1650°C for 30 min. Specimens tested at 1900°C and below were pretest-annealed at 1900°C for 2 50 hr. Specimens tested above 1900°C were pretest-annealed at 2400°C for 5 hr. The impurity content in the "as-received" plate was quite low, table I. Essentially no change in impurity levels was detected in specimens after creep testing. All creep tests and annealing treatments were conducted in a vacuum of 10-8 torr in a test furnace heated by a tungsten mesh element. The load was applied to the specimens through a bellows, and stresses were maintained to ±1 pct of the selected value by periodic corrections for changes in specimen cross-sectional area during creep and for changes in the bellows spring force due to load column extension. One-inch-diameter tungsten force rods were used in the hot zone of the furnace. Deformation at temperature was measured by optically tracking gage marks on the specimen. Temperature was measured by a calibrated optical pyrometer and was determined to ±5"C. Grain sizes were determined by the linear intercept method and specimens were examined in the "as-polished" condition, using polarized light. Specimens annealed at 1900°C had a grain size of 52 ± 5µ , and those annealed at 2400°C had a grain size of 148 * 11 µ. Pieces were cut from the gage section of creep-tested specimens and planed to a thickness of about 0.010 in. by spark discharge machining. Thin foils for viewing by transmission electron microscopy were obtained by electropolishing in a solution of 6:3:1 ethyl alcohol, perchloric acid, and butoxy ethanol, respectively, using the window technique. Bath temperature was —4OoC, and the cell potential was 35 v. The foils were examined in Siemens Elmiskop I, operating at 100 kv. RESULTS AND DISCUSSION In order to analyze the results from creep experiments, Eq. [I] is rewritten in the following form: <=Kf(s)ne-/RT [2] where K = constant, ?// = apparent activation energy for creep,

Jan 1, 1970

By Appendix by A. S. Goldoni, R. E. Tate, E. M. Cramer

The diffision coefficient for self-diffision of plutonium in the temperature range 350" to 440°C has been measured by using puZ3 as the tracer isotope. Autoradiopaphic techniques were used to inzlestigate the possibility of grain boundary diffusion, hut only evidence for volume diffusion was found. The least-squares fit of the data gives the .following equation for the diffision coefficient: The computer least-squares technique for fitting the nonlinear equations is outlined. DETERMINATION of the self-diffusion coefficient of the fcc 6 phase of plutonium is in principle a straightforward experimental task. However, the chemical reactivity, the intense @ activity, and the toxicity of plutonium put limitations on the experimental techniques. The technique selected included roll bonding for preparation of the diffusion couples and pulse-height analysis of the @-particle activity to determine the distribution of the PU tracer in the diffusion couples. EXPERIMENTAL PROCEDURE Couple Preparation. Cylinders about 0.5 in. in diam were cast from two special stocks of plutonium, one of which had been enriched in puZ3&apos;, as shown in the isotopic analyses listed in Table I. For each roll-bonded composite sheet, a cylinder 0.437 in. in diam and 0.190 in. thick was turned from each kind of plutonium on a lathe in a 98 pct He atmosphere. The two freshly machined cylinders were positioned face to face in a tube of commercially pure aluminum which had been sealed at one end by welding and the assembly was evacuated on a vacuum manifold overnight. The elapsed time between machining the faces of the plutonium cylinders and evacuating the loaded tube was about 15 min. After overnight evacuation of the assembly the indicated vacuum was 1 X 10"5 torr or better. The aluminum tube was then warmed and pinched off with a cold-welding tool. The pinched-off weld was also fusion-welded as an additional precaution against leakage of air into the evacuated assembly. The assembly was immediately heated for 30 min in a 250°C furnace and reduced in thickness by being passed through a rolling mill with rolls heated to 200°C. The rolling schedule (four passes of 100 mils each with a 10-min reheat after two passes) reduced the thickness of the assembly to 100 mils. The rolled assembly was allowed to cool normally in air. The rolled assembly was sheared at the edges and the aluminum peeled from the composite plutonium sheet. The elliptical sheet was about 0.060 in. thick and usually three 0.383-in.-diam disks could be punched from its central portion. The sheet was heated on a hot plate to the ductile low 0 range (140°C as measured by temperature-indicating pellets) before each disk was quickly punched. The quality of the bond in the disks was evaluated by metallographic examination of the scrap sheet adjoining the hole left by the punch. Only well-bonded specimens without oxide in the interface (as indicated by metallography) were considered satisfactory for further use. More than half of the specimens so examined contained sufficient oxide in the interface to be rejected. Diffusion Anneal. Each disk to be diffusion-annealed was wrapped in 1-mil-thick tantalum foil and sealed within a Pyrex capsule evacuated to 1 x 10~5 torr or better. This capsule was then sealed within another Pyrex capsule at a similar pressure. The diffusion anneals were carried out at temperatures between 350" and 440°C in Marshall furnaces adjusted to have a temperature gradient of not more than *1/2"C over a 5-in. length. This gradient was then further smoothed by using a nickel tube as a liner in the furnace. The liner was divided into three longitudinal cavities by a septum of nickel sheet to which two calibrated Chromel-Alumel thermocouples were attached. One thermocouple was used for controlling the furnace temperature by means of a Brown Pyrovane controller equipped with a Capaciline anticipation circuit; the second thermocouple was monitored twice daily with a Leeds and Northrup K-2 precision potentiometer.

Jan 1, 1964

By M. H. Yoo

Possible interactions of the perfect dislocations of six slip systems or the c dislocation with the (10i2f (ioii), {ioIi}(ioiZ), {1122}(1123), and {1121}(ii26) type twins in hcp metals have been analyzed from the crystallographic and the energetic points of view. Twenty-six distinct types of possible interactions were identified, and those selected based on crystallographic constraints were examined for their energetic feasibilities by use of the anisotropic energy factors. No long-range elastic interaction exists for a dislocation when its Burgers vector is parallel to the twin interface. Under a suitable applied stress, a screw dislocation can cross slip at the twin interface. For basal mixed dislocations in cadmium and zinc, the interaction with {1012} twins is found to be attractive, indicating that incorporation of these dislocations into the twins is energetically feasible and that twin growth will result. On the other hand, the interaction between both basal and Prism mixed dislocations and the {1012} and (1121) twins is found to be repulsive in Mg, Co, Re, Zr, Ti, Hf, and Be. This indicates that under an applied stress a local stress concentration will develop due to a dislocation pileup at the interface, which may result in a site for either the nucleation of other twins or the formation of a crack, depending on the cleavage strength. WHEN a metal undergoes plastic deformation, a certain configuration of slip dislocations will result in a state of dislocation pileup against an obstacle. The stress concentration thus developed may enhance the process of twin nucleation and also twin growth. Furthermore, once formed and dispersed in the crystal, twins can act as effective barriers against slip dislocations. The degree of such mutual influence or interrelation between slip and twinning is generally known to be pronounced in the case of hcp, metals. It is also known that deformation by twinning occurs more commonly in hexagonal metals than in cubic metals. In fact, under suitable stress states, all hexagonal metals exhibit {1012) <1011> type twinning.&apos; In addition to this common type, deformation by (1151) <1126> type twinning occurs in zirconium, titanium, and rhenium, which show remarkable ductility.&apos; The importance of twinning during general deformation to the ductility of hcp polycrystals has been briefly discussed in recent review works.2&apos;3 The purpose of this paper is to analyze the interaction between slip dislocations and twins in the hcp structure and to discuss the nucleation and growth processes of twinning and the role of twinning in the <"°" noil) o, 1/3[112O] (OOO2) 1/3[1123] Fig. l—-Slip systems in hcp structure. ductility of hexagonal metals. The problem will be discussed from the geometric and the energetic points of view in a manner similar to that of the previous work on zinc.4 Since hcp crystals deform by several slip and twin systems, numerous interactions result as possibilities. The Burgers vectors of six slip systems and the c dislocation shown in Fig. 1 and the four twin systems listed in Table I are considered here. A complete tabulation of the possible interactions is followed by discussion of those that are more likely to occur on the basis of crystallographic constraints and energetic considerations. 1) CRYSTALLOGRAPHY OF TWINNING The crystallographic elements, K1, K2, n1, and n2, for the four compound twin systems are now well established.= A unit cell with the base vectors n1, and n2 is shown in Fig. 2 for each twin system. The unit cell before twinning is shown in solid line, and the corresponding unit cell after twinning is shown in dashed line. Also shown in Fig. 2 are the following crystallographic parameters: S is the plane of shear, d the interspacing of the twin habit planes K1,Ø Iis the acute angle between n1, and n 2, e is a numerical factor, and q is the number of K, lattice planes intersected by 17&apos;. These parameters can be expressed in terms of the axial ratio, y = c/a, as listed in Table 11. The macroscopic shear strain of twinning, s, and the magnitude of a "unit twin dis-l~cation,"4 bt, are also expressed in terms of y and given in Table 11. In Table 11, K1 and q1 are given in both Miller-Bravais and Miller indices. In double lattice structures, shuffling of atoms in addition to a homogeneous shear of the lattice is generally required if the original crystal structure is to be restored after twinning. The extent of current understanding on this problem of atom shuffling is per- Table I. Four Twin Systems in Hcp Structure

Jan 1, 1970

By N. S. Stoloff, K. R. Jordan

The temperatwe and grain size dependence of the mechanical avoperties of ordered and disordered Fe-49 pct Co-2 Pct V were investigated. The yield and flow stresses obeyed the Hall-Petch relationship u = ai + kd-&apos;I2. Ohdering reduced the intercept stress cjj and raised the Petch slope, k, at all temperatures. Ordering also increased the temperatwe dependence of k. The ductile to brittle transition temperature increased with order and grair~ size. Cleavage fracture was nucleation limited and the fracture stress did not zlary linearly with d-&apos;". A quantitative test of the Cottrell-Petch fracture theory (and recent modifications which consider the influence of slip mode), demonstvated that this theory is not applicable to FeCo-V. COTTRELL&apos; and etch&apos; independently suggested that a criterion for cleavage failure at the yield point, a,, based on dislocation pileups at a grain boundary or other obstacle to dislocat.ion motion, is: aYYkd&apos;I2 1 opy [ll or, equivalently, aikz,d112 +k:)bpy [2] where a, and ky are the Hall-Petch intercept and slope, respectively, 2d is the grain diameter, P is a geometric factor dependent on the macroscopic ratio between shear and tensile stress, p is the shear modulus, and y is the true elastic surface energy. When the product of quantities on the left side of the equation is equal to or exceeds that on the right, cracks should be able to nucleate and propagate at the yield stress, as shown schematically in Fig. 1. Therefore a high intercept stress, high Petch slope, or coarse grain size favors brittleness. petch3 associated the existence of a ductile to brittle transition in ferrous alloys with the temperature dependence of ai. One of the earliest modifications of the Cottrell-Petch theory was presented by ~rmstrong,~ who derived an expression for transition temperature in terms of several measurable flow and fracture parameters. The latter paper was able to rationalize situations in which the transition temperature increases with decl-easing grain size, as in the case of molybdenum,&apos; and also suggested that Ppy should be a function of grain size as well as temperature. More recently Johnston et a1.6 and Smith and worthington7 have suggested that the temperature or composition dependence ol&apos; ky must also be taken into account if there is any cha.nge in deformation mode, as from wavy to planar slip, or wavy slip to twinning, with change in temperature or solute content. Armstrong %as suggested that for hcp metals changes in o;k,dw> o;k,d1/2< / is / ^^^^ / / y_______________________________________ d-"2 Fig. l—Schematic representation of grain size dependence of yield stress, cry, and fracture stress, CTF. Intersection defined by Cottrell-Petch equation. slip mode should be incorporated in the theory through changes in the critical resolved shear stress for the slip system which controls ky. The purpose of the present investigation was to critically test the modified677 Cottrell-Petch theory of fracture in the superlattice alloy Fe-49 pct Co-2 pct V, by studying the grain size dependence of the yield and fracture stresses over a range of temperatures, in conjunction with an investigation of slip mode and fracture behavior. Previous work has shown that long range order results in a sharp decrease in flow stress, a small increase in work hardening rate and a drastic upward shift in the ductile-brittle transition temperature of F~CO-V.~&apos;~ The only comprehensive study of slip character in this alloy has been reported in a preliminary account of the present investigation.10 EXPERIMENTAL PROCEDURE The experimental work was carried out on material produced from a 10 lb vacuum melted ingot, of composition 49.32 wt pct Co, 2.09 wt pct V, balance Fe. 30-mil thick sheet samples with a 1; in. gage section were machined from cold rolled stock. The degree of cold work ranged from 85 pct for the finest grained samples to 5 pct for the coarsest grain size. Details of ingot fabrication are reported elsewhere." Equi-axed grain sizes in the range 12.7 to 75.4 p were obtained by annealing for varying times at 850°C. (Re-crystallization annealing time, rather than temperature , was varied to control grain size to insure that samples of all grain sizes contained equivalent quenched-in vacancy and interstitial concentrations.) Grain sizes were measured by the line intercept method on several specimens of each grain size. Following recrystallization, all samples were disordered by quenching into iced brine.

Jan 1, 1970

By Eckhard Nembach

The phase diagram of the system Pb-In has been investigated between -27° and + 40°C, using nzainly X-ray dijfraction. In accordance with t her mo dynamic measurements by Heumann and Predel, a segregation occurs at low temperatures, though not in the form of a nziscibility gap. THE phase diagram of the system Pb-In has been the subject of extensive investigations,1&apos;1 but recently Heumann and prede13 concluded from their thermodynamic data that a new feature should occur below room temperature. These authors observed that the maximum values for the enthalpy and entropy of mixing, which occurred at a composition of 50 at. pct Pb, were +400 and —1.7 cal per g-atom deg, respectively. From this the authors estimated that a miscibility gap should occur below 30°C, centered at 50 at. pct Pb. Resistivity measurements seemed to support this view. These authors proposed the phase diagram outlined in Fig. 1. Three phases exist at 30°C: the tetragonal indium phase with c/a > 1, the tetragonal intermediate phase a, with c/a < 1, and the fcc lead phase. During an investigation of the superconducting properties of Pb-In alloys. it has been observed4 that aging a specimen with 50 at. pct Pb for 14 days at -18°C decreased the superconducting transition temperature about 0.13"K and tripled the transition width. In this paper, the results of an investigation of the Pb-In phase diagram in the temperature range from — 2T to +40°C are reported. Superconductivity and X-ray methods have been used. 1) SPECIMEN PREPARATION The materials were provided by the American Smelting and Refining Co. According to the manufacturer their purity was 99.999 pct. The weighed amounts of the constituents were sealed in quartz tubes under an atmosphere of 10 torr helium, mixed for 24 hr in a rocking furnace at 380°C, quenched in ice water, and homogenized at 20" to 30°C below the solidus line, established by Heumann and Predel. The annealing times were 144 hr for specimens containing Less than 30 at. pct Pb and 36 hr for the remainder. 2) SUPERCONDUCTIVITY EXPERIMENTS The specimens were quenched from the homogeniza-tion treatment into ice water and their superconducting transition temperatures T, measured. The procedure used has been described in Ref. 4. The transition was detected by the change of the mutual induc- tance of two coaxial coils containing the sample. T, was defined as the temperature at which 50 pct of the total change in inductance had occurred. The repro-ducibility with which T, could be measured was i0.002"K. Then the specimens with lead contents between 38 and 75 at. pct were aged for 7 days at temperatures between -30" and 40°C. If this treatment caused T, to change by more than 0.005"K or the width of the transition to increase by more than 0.002"K, it was concluded that the specimen had undergone a phase change and no longer consisted only of the fcc lead phase: as it did immediately after homogenizing. The result is shown in Fig. 2. From this one can estimate at what temperatures and concentrations phase changes occur. The X-ray measurements were based on these preliminary results. 3) X-RAY EXPERIMENTS Because of the softness of the material, relatively coarse powders. 75 p, had to be used, which were filed in a helium atmosphere from homogenized specimens. The powders were annealed at least 30 min at temperatures between 120" and 16OJC, depending on their concentration, and quenched in ice water. Then their X-ray patterns were taken at -178°C with a Picker diffractometer, model 3488K, and a cold stage. on which the specimen was in thermal contact with a liquid-nitrogen reservoir. In this way the following relation was established for the fcc lead phase: a = 4.697 + 0.00247C for 40 5 C 5 75 11 where n is the lattice constant (A) and C is the at. pct of lead. The coarseness of the powder made it impossible to use lines with 0 > 75 deg; therefore n was averaged from lines with 45 deg 5 0 5 75 deg. The results were reproducible to within i0.05 pct. Relation [I] is very similar to the one found by Heumann and Predel at room temperature. Following this, homogenized specimens with compositions between 15 and 56 at. pct Pb were aged for at least 10 days at temperatures between -27" and

Jan 1, 1970

By David Turnbull

IN isothermal recrystallization processes, new crystals generally grow into the matrix until they impinge upon other new crystals or an external surface, at constant linear rates G. Before impingement the perceptible course of growth can be described by the equation: 1 = G(t-7) C1I where, G = dl/dt, 1 is a crystal dimension measured in a constant direction, t is the time, and 7, the nucleation period, is a positive intercept on the time axis. Fig. 1 is a schematic representation of I as a function of time for a recrystallizing grain. G is dependent upon temperature, driving energy (strain or surface energy), relative grain and boundary orientations, but is generally independent of time. The frequency of nucleation, fi, (time" volume") can be defined by the equation: N = 1/fV [2] where ? is the mean nucleation period and V is the volume of the specimen that has not recrystallized. The kinetics of primary and secondary recrystallization generally can be described satisfactorily in terms of the parameters N and G only.&apos;-" After recrystallization is complete the average grain size 7 increases with time by "normal grain growth;" didt, the average rate of grain growth, is strongly time dependent and has not yet been precisely related to G for the motion of the individual grain boundaries constituting the system. It has been suggested4* " that the elementary act in grain boundary migration is closely related to the elementary act in grain boundary self-diffusion. Although the distance of atom movement in the two processes may be somewhat different, there is reason to expect that the activated states may be very similar, so that the free energy of activation for grain boundary migration should be of the same order of magnitude as for grain boundary self-diffusion. Therefore, it is desirable to develop a satisfactory basis for comparing data on self-diffusion and grain boundary migration and to make such comparisons where possible. Theory The formal theory of grain boundary migration rates is analogous to the theory for the rate of growth of crystals into supercooled liquids reviewed elsewhere 6-8. Boreliuss has shown that the latter theory describes, within the theoretical uncertainty, the growth of selenium crystals into supercooled liquid selenium. Motto and more recently Smolu-chowski" have derived expressions for the rate of boundary migration in recrystallization. The treatment to be presented is similar to Mott&apos;s excepting that the formalism of the absolute reaction rate theory will be used. The atomic mobility, M, in grain boundary migration is defined by: G = -M6p/6x where p is the chemical potential per atom and x is the coordinate measured in the direction of grain boundary movement. Let AF be the free energy difference per gram atom on the two sides of the boundary and k the thickness of the boundary. For RT>>AF the potential gradient across the boundary (6p/6x) is essentially linear and it follows that: SF/8x = - aF/N\ [4] where N is Avogadro&apos;s number. According to the Nernst-Einstein equation, M is related to a diffusion coefficient, Do, for matter transport in grain boundary migration by the equation: M = Da/kT [5] Substituting eqs 4 and 5 into eq 3 gives the basic relation between Do and G: G = DoaF/\RT [6] Do values may be calculated from experimental values of G from eq 6 and directly compared with the coefficient of self-diffusion within the crystal, DL, or the grain boundary self-diffusion coefficient D,. However, a more convenient, though equivalent, basis for comparing atomic mobility in grain boundary migration and self-diffusion is through the constants of the absolute reaction rate theory. According to this theory diffusion coefficients may be written:" D = k2(kT/h) exp [-AF,/RT] 171 aFa, the free energy of activation, is related to the measured energy of activation, Q, by the equation: AFA = Q - T aSx - RT [8] where aSa is the entropy of activation. Substituting eqs 8 and 7 into eq 6 gives: G = ek(kT/h) (aF/RT) exp [(AS,,)C/R] exp C-Qc/RTI C91 where the subscript G refers to boundary migration. The relationship between the driving free energy and the free energy of activation in boundary migration is indicated schematically in Fig. 2. Experience indicates that the variation of G with temperature can be described by: G= Go exp [- Qc/RT] [10] where Go and Qc are generally temperature independent over wide ranges of temperature. Comparison of eq 9 with eq 10 gives:

Jan 1, 1952

By A. H. Daane, J. J. Hanak, F. H. Spedding

IN the study of the rare earths at the authors&apos; laboratory, methods have been devised for preparing pure rare earths and many of their properties&apos;- have been determined. Very little information is found in the literature on the properties of europium metal, which is the scarcest of the naturally occurring rare earths. Since we have recently prepared europium in appreciable quantities, we are in a position to describe the method of preparation and some of the properties of this metal. Metallic europium was first prepared by Klemm and Bommera who heated a mixture of potassium and EuC1, in vacuo, and obtained a mixture of europium metal and KC1. Trombe4 electrolyzed a molten salt bath containing NaC1, KC1 and EuC1, and collected the europium in a molten cadmium electrode as a cadmium alloy. The cadmium was subsequently removed by distillation but the properties of the residue indicate that pure europium was not obtained. McCoy attempted to prepare europium by distilling mercury from europium amalgam, but the stability of the Eu-Hg intermetallic compounds prevented a complete separation of the two elements. The preparation of very pure europium was suggested by previous work in this laboratory1,4 in which ytterbium and samarium were prepared by heating the respective sesquioxides with lanthanum metal turnings to 1450°C in vacuo and distilling ytterbium and samarium from the mixtures. Subsequently, small test experiments showed that europium also could be prepared by this method. A more detailed version of this method was used in the work described in this paper. Klemm and Bommer3 found by X-ray analysis that the metal had a body-centered cubic (bcc) structure with a lattice constant a, = 4.582 ± 0.00A (converted from kX units), with a bulk density of 5.30 g per cu cm. They found europium to be weakly ferromagnetic. Spedding, et al,7 found a,, to be 4.606 ± 0.001A. Barrett&apos; showed that the bcc structure persists throughout the temperature range 5 to 3000K with a, at 5, 78, and 300°K being 4.551 ± 0.003, 4.551 ± 0.004 and 4.577 ± 0.001A, respectively. Trombe1 described europium as being iron gray, malleable, about as hard as neodymium and not attacked by cold water. He estimated the melting point to be between 1100 and 1200°C. Previous work in this laboratory indicated that the pure metal corrodes rapidly in air and reacts with cold

Jan 1, 1959

By R. F. Mehl, B. Lustman

The formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.&apos; It is necessary here only to cnumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type—i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained—the isothermal growth of the phase follows a simple parabolic equation: X2 = kt [i] where X is the thickness of the alloy layer, k thc reaction rate constant, and t the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.$ In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varics with temperature according to the Arrhenius equation: k = Ae-Q/RT [2] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. Ali phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By R. F. Mehl, B. Lustman

The formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.&apos; It is necessary here only to cnumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type—i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained—the isothermal growth of the phase follows a simple parabolic equation: X2 = kt [i] where X is the thickness of the alloy layer, k thc reaction rate constant, and t the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.$ In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varics with temperature according to the Arrhenius equation: k = Ae-Q/RT [2] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. Ali phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By R. S. Wagner, C. E. Miller, H. Brown

A dc field was applied to liquid BI-Sx or Au-Ge alloys of eutectic composition. The liquid alloys were kept at a temperature slightly above the eutectic. The concentration changes due to electrodijfusion are large enough to cause nuclcation and growth of the primary phases at the respective electrodes. Nearly complete separation of Bi-Sn eutectic was obtained as well as substantial separation of Au-Ge eutectic. The effect of an electric field on the solute distrihn-tion was itluestignted itt tlirectiortally solidified rods of a dilute Bi-Sn (0.5 al. pc,t Bi) alloy. Field-freezing was carried out in small-diameter cupillay tubes to avoid cotuectice mixing -of the liquid. The relative sollcte corzcentratioi, Cs/Co , was rneusred by n radioac1il.e tracer netlod. Cs/Co can be made both largev than unity or srialler than the equilibiuwz distvibrrlion c.oejyicienl, k, , oiler a substattiul portion of the soliclifi&apos;erl rocls. A direct current, passed through a liquid-metal solution, can cause substantial concentration changes by electrodiffusion. The magnitude of the change depends on the difference in ionic mobilities of the atomic species in solution. Electrodiffusion has been studied in many binary and ternary liquid alloys.&apos;y2 It was found that the rate of material transport decreases with time for a constant applied field, as a concentration gradient is established in the solution. A steady-state concentration profile is achieved when electro-diffusion is compensated by chemical diffusion. This may seem to limit the use of electrodif fusion for metallurgical application. However, a way of utilizing the effect of electrodiffusion is to combine it with crystallization or controlled freezing. rakin was first to propose this as a new method of separating metal alloys of eutectic composition at temperatures slightly above the eutectic temperature. It was possible by this method to separate Bi-Sn and Bi-Cd eutectics into their component phases. Angus et al discussed the possibility that the effective distribution coefficient, keff, could be varied by proper application of an electric field during solidification. The combination of electrodiffusion and solidification, called field-freezing, was discussed in detail by Pfann and aner. It was shown that field-freezing can be used as a crystal-growth process, an efficient method for eutectic separation, and a new means of changing the effective distribution coefficient. k,ff, beyond the usual range of ko < k,ff < 1. The liquid layer adjacent to the solid-liquid interface can be either increased or depleted in solute due to

Jan 1, 1967

By R. F. Mehl, B. Lustman

THE formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.1 It is necessary here only to enumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type-i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained-the isothermal growth of the phase follows a simple parabolic equation: [1 = ki [I]] where X is the thickness of the alloy layer, k the reaction rate constant, and [t] the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.3 In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varies with temperature according to the Arrhenius equation: [k = Ae-QIRT [2]] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By J. D. Mote, A. Rosen, J. E. Dorn

The effect of strain rate and temperature on the critical resolved shear stress for (1100) [1120] prismatic slip was determined for the intermediate hexagonal phase containing about 67 at. pct Ag and 33 at. pct Al. Whereas the flow stress increased only slightly as the test temperature was first decreased below room temperature, a rapid increase inflow stress was obtained with yet greater decreases in temperature from about 240" to 4°K. The effect of both temperature and strain rate on the flow stress over the low-temperature range could be completely rationalized in terms of the Peierls mechanism when the deformation is controlled by the rate of nucleation of pairs of kinks. A few years ago Mote, Tanaka, and Dorn1 observed that the critical resolved shear stress for prismatic slip of a 67 at. pct Ag plus 33 at. pct A1 hexagonal intermediate phase by the (1100)[1120] mode decreased precipitously as the test temperature was increased from 4" to about 160°K. Their results for both basal and prismatic slip are given in Fig. 1. It is obvious that only the flow stress for prismatic slip is strongly temperature-dependent, whereas the flow stress for basal slip is independent of temperature. If the temperature dependence of the flow stress were primarily due to interstitial impurities, it might be expected that they would influence the flow stress for basal slip as well. Since the activation volume at 115°K for prismatic slip was determined to be about 15b3, where b is the Burgers&apos; vector, this thermally activated deformation process was tentatively ascribed as being due to the Peierls mechanism. But the various analyses of the Peierls mechanism then available as formulated by Seeger2 and also by Lothe and Hirth3 did not agree well with the experimental data. Since that time a more realistic theory for the operation of the Peierls mechanism under conditions where the strain rate is determined by the rate of nucleation of pairs of kinks has been presented by Dorn and Rajnak.4 The present investigation was, therefore, undertaken in order to provide the essential data for a careful check on the agreement between this theory and the low-temperature deformation by prismatid slip of the above-mentioned Ag2A1 intermediate phase. EXPERIMENTAL TECHNIQUE Single-crystal specimens so oriented that the [1120] direction and the normal to the (1100) plane were at 45 * 2 deg to the tensile axis were grown from the congruent melting composition of about Ag2Al for the intermediate hexagonal phase by the

Jan 1, 1964

By C. D. Tedmon, D. P. Ferriss

THE yield stress, o of low-carbon steel has been shown to vary with the average grain diameter, d, according to the relation1-3 where o is taken to be the lower yield-point stress Of is the friction stress on an unlocked dislocation, and ky is a constant. The interpretation2,4 of ky in terms of dislocation theory relates this constant to the stress to unlock a source across a grain boundary. cottrel14 predicted that ky would increase with decreasing temperature. This was observed to be the case by Adams and coworkers5 in their investigation of niobium (columbium). However, petch6 and Backofen: both working with low-carbon steel, found ky insensitive to temperature. In his work with high-purity niobium, Johnson&apos; found ky equal to zero. Evansg showed that k, was essentially zero for niobium containing nitrogen in an appreciable concentration range. The present experiments were designed to check this apparent anomaly in the value of ky in another Group V metal. Yield points were determined as a function of grain size at several temperatures for tantalum and a tantalum-tungsten alloy. The material used was double are-melted tantalum and a double are-melted alloy of 90 pct Ta and 10 pct tungsten (by weight), both obtained as unannealed, swaged rod. The impurity content of the materials is given in Table I. The tantalum was annealed at 1325"C. in a vacuum resistance furnace using a tantalum boat. The alloy was similarly annealed at 1660°C. Annealing times varied from 15 min to 2 hr, depending on the desired grain size. Nominal pressure in the furnace was 3 X 10~4 mm of Kg. Metallographic examination showed that the annealing treatment produced grain sizes ranging frorn 0.021 to 0.200 mm in the tantalum, and 0.060 to 0.160 mm in the alloy. Tensile bars were made by centerless grinding the annealed specimen;, and then electropolishing to remove all grinding marks. The specimens were than pulled :it 2 1/2 pct per rnin in an Instron testing machine. The tantalum specimens were tested at 77", 195", and 300°K. The alloy was tested at 300°K only. All specimens exhibited a yield-point phenomenon at all temperatures. Typical load-elongation curves at the three test temperatures are shown in Fig. 1. The lower yield stress is plotted as a function of (grain size) in Figs. 2 and 3 for tantalum and the 90 pct Ta-10 pct W alloy, respectfully. The position and slope of the curves was determined by least-

Jan 1, 1962

By Carl F. Floe, John Chipman

THE system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100° to 1500°C., and pressures from about 20 mm. of mercury to somewhat above atmospheric. REVIEW OF PREVIOUS WORK The solubility of gases in most liquids has been found to obey Henry&apos;s law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as 02, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts&apos; law. It may be recognized as a special case of Henry&apos;s law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: [(MG) l 2M +G2 = 2MG K = Ma X Pa, [I]] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: [MG = Kl Pa,[2]] Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: [6Cu + SO2 = Cu2S + 2Cu20[3] K _ Cu2S X (Cu20)2 (Cu)6(Pso2)[4]] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: [8 =KI = Pte, or VSO2= K2 &apos;~/PeO, [S]]

Jan 1, 1941