Search Documents

Some 30,000 people attended from 50 countries. Over 600 exhibitors brought with them a billion dollars of mining technology, ranging from tiny high-precision valves to giant off-highway trucks. Twenty-seven technical sessions with more than 100 papers covered the gamut of mining advancements. It was a grand display of industry vitality just to power the huge exhibit area required 22,000 kW of electricity each day, and support services for the exposition created more than 1000 daily jobs for local labor. Unquestionably, Las Vagas knew the miners were in town for the American Mining Congress' International Mlining Show.

Jan 11, 1978

By B. W. Levinger

THE lattice parameter of the ß form of pure titanium has been measured at elevated temperature.', ' No attempt was made, however, to correct the parameter obtained to room temperature. In the course of phase diagram studies at Armour Research Foundation and elsewhere, the variation of ß-phase lattice parameter with composition has been established in a number of binary and ternary systems involving titanium. It was possible to extrapolate in these instances to 100 pct Ti to find the apparent lattice parameter of ß titanium at room temperature. Table I lists the results thus obtained. The suggested value for the lattice parameter of ß titanium is the average of the extrapolated values 3.276 ±0.003 kX. This suggested value gives an interatomic distance in ± titanium of 2.837 kX and hence a Goldschmidt atomic diameter (coordination number 12) of 2.925 kX. The latter agrees closely with the value of 2.93 given by Hume-Rothery." From the data of Adenstedt and coworkers' it was possible to determine by extrapolation the mean coefficient of linear expansion for /3 titanium in the range from room temperature to 1000°C. This value, 10.1x10-8 per degree C, compares with about 11x10-8 for a titanium in a similar range." It was thus possible to calculate the parameter at 900 °C. The value of 3.305 kX agrees well with 3.3065 given by Eppel-sheimer.' The majority of values reported in the literature7-', ' were given as Angstroms. In at least one case, ref. 8, it was shown that they actually represented kX units. The source of this confusion appears to be that a large number of tables of X-ray emission spectra list wavelengths as Angstroms and give values in kX units. The accepted conversion factor for kX units to Angstroms (10.' cm) is 1.00202. Thus the parameter of ß titanium suggested corresponds to 3.282A. References J. H. de Boer, W. G. Burgers, and J. D. Fast: Proc. Acad. Amsterdam (1936) 39, p. 515. 2D. S. Eppelsheimer and R. R. Penman: Nature (Dec. 2, 1950) 166, p. 960. 3 W. Hume-Rothery: The Structure of Metals and Alloys (1945) London. Inst. Metals. 4 H. K. Adenstedt, J. R. Pequignot, and J. M. Raymer: Trans. ASM (1952) 44, p. 990. 5 Gmelins Handbuch der Anorganischen Chemie. Titan, Verlag Chemie, Weinhein (1951). 8 P. Pietrokowsky and P. Duwez: Trans. AIME (1952) 194, p. 627; Journal of Metals (June 1952). 7 P. Duwez and J. L. Taylor: Trans. ASM (1952) 44. D. 495. 8 M. Hansen, E. L. Kamen, H. D. Kessler, and D. J. McPherson: Trans. AIME (1951) 191, p, 881; Journal of Metals (October 1951). 8 Unpublished Research, Armour Research Foundation.

Jan 1, 1954

By T. M. Morris

R. T. Hukki (Finland Institute of Technology, Helsinki, Finland)—Two schools of thought are developing concerning the order of the rate of flotation. The paper by Morris is intended to show experimental evidence in favor of the first order rate. Arbiter, on the other hand, has presented an earlier paper" to demonstrate the validity of the second order rate equation. Unfortunately his method of plotting is open to criticism, as pointed out by Morris." A more sensitive method of plotting has been described by the writer,= whereby the data presented by Arbiter demonstrate the superiority of the second order plot. The general rate equation may be written in the following forms for the integrated first and second order equations: (A) t = -1/k In Co-R/Co (first order) [4] 1 (B) 1/t = - kCo + kCo2 1/R (second order) As a first approximation the value of Co may be taken as a unity, 100 pct or 1. Whether or not this is the case in all tests performed by Morris is impossible to judge, owing to the fact that the flotation times are extremely short, e.g. 150 sec in tests A. It would, indeed, be very interesting to know what the total recovery R would be after 1 hr of flotation, for example, instead of after 150 sec. Certainly there are circumstances when C, approaches unity within a very small margin of error. Morris has used the same approximation in his example D "since the feed to this cleaner

Jan 1, 1954

By Pierre I. Desré, Donald T. Hawkins, Ralph Hultgren

The torsion effusion method has been used to measure the vapor pressure of thallium over pure thallium in the temperature range 931" to 996'k The resulting 100 cal per g-atom is in excellent agreement with previous values. Vapor pressures of T1 above seven Ag-Tl alloys ranging from 33 to 90 at. pct T1 were measured at 979K. Calculated silver activities show a positive deviation from Raoult's law, approaching ideality near the liquidus. Measured thallium activities scatter less than previous measurements using the electromotive force technique. Values for the silver component were calculated by Gibbs-Duhem integration. This paper reports the results of a study of the liquid Ag-T1 system by the torsion effusion method. The method has been discussed in detail previously1 and will be only briefly summarized here. The sample is contained in a cell which is suspended on a torsion wire. Vapors effusing from orifices on opposite sides of the cell exert a torque on the wire. The torque is related to the vapor pressure by the following relation: where D is the torsion constant of the wire, 4 the angle of torque, fl and f2 the correction factors determined by Freeman and seamy2 to account for orifice length, a1 and a2 the areas of the orifices, and ql and q2 the distances of the orifices from the axis of rotation. By using the same cell for pure thallium and the alloy, it follows that: so that most systematic errors are eliminated in determining the activities. EXPERIMENTAL 99.999+ pct T1 was obtained from the American Smelting and Refining Co. and 99.999 pct Ag was obtained from Cominco American, Inc. Seven Ag-T1 alloys, ranging in composition from x^\ = 0.33 to 0.90, were prepared by melting together weighed amounts of the pure metals in sealed, evacuated Vycor tubes and quenching the melts in water. The apparatus and graphite cells were the same as those used by Hawkins and Hultgren3 in their study of the Pb-Sn system. RESULTS Ten measurements were made on pure thallium in the temperature range 931" to 996K, and the results are presented in Table I. Values of were calculated using tabulated Gibbs (free) energy functions.4 No dependence of on temperature or orifice size was found, indicating that equilibrium was attained. Data for the Ag-T1 alloys are shown in Table 11. Values were smoothed with respect to composition by a plot of where . DISCUSSION The value = 43,520 * 100 cal per g-atom for pure thallium (95 pct uncertainty limit) is in excellent agreement with previous investigations.4 In the Ag-T1 system, this study shows positive deviations from Raoult's law at all compositions. Fig. l gives the phase diagram according to Hansen, and Fig. 2 presents the activity values measured in this study as well as those from electromotive force measurements at 950°K by Terpilowski, Kundys, and slaby.'

Jan 1, 1969

CONTENTS PAGE WARNER, ROBERT K.-Efficiency of Screening. Discussed by Robert C. Canby,Robert K. Warner, W. 0. Borcherdt, V. E. Flanagan 1 FAHRENWALD, A. W.-Surface Reactions in Flotation. Discussed by Arthur F. Taggart, A. M. Gaudin 7 Efficiency of Screening Discussion of the paper of ROBERT K. WARNER, presented at the New York Meeting, February, 1924, and issued, as Paper No. 1293-M, with MINING AND METALLURGY, January, 1924. ROBERT C. CANBY, Wallingford, Conn.-On page 2, the author speaks of the importance of using a testing sieve clothed with the same material as the screen being studied; does he regard this as essential? In practice, how does the screen efficiency calculated by the difficult-grain method compare with those computed by the usual undersize method? Is it possible by the author's method, to obtain a measure of efficiency that can safely be compared with that of another screen sizing a different ore? ROBERT K. WARNER.-The use of a testing sieve clothed like the mill screen being studied is desirable but not essential for routine work about a mill where the character of the feed varies little, as regards the shape of the grains and the sizing test. Close agreement in size of aperture between the sieve and the screen is, however, important if the data obtained are to be valuable to others working on a different feed. If the testing sieve is coarser than the mill screen, the efficiency will appear unfairly low; whereas if it is too fine one might get efficiencies greater than 100 per cent. because of the apparent oversize in the undersize. In either of these cases the usefulness of the difficult-grain method of calculation would be reduced. As screens wear, the undersize grows appreciably coarser so that it is desirable to test screens only when the cloth is new or else to provide testing sieves that are worn about the same amount. The futility of making efficiency observations on a. distorted or broken screen surface is obvious.

Jan 6, 1924

By A. B. Cook, C. J. Walker, G. B. Spencer

Although water will displace oil from a petroleum reservoir to a greater extent than gas will, there are some reservoirs in which gas rather than water should be used for pressure maintenance. This is indicated by the high-percentage oil recovery in the case history reports on the Pickton field1 in East Texas and the Raleigh field2 in Mississippi. In gas cycling, total oil recovery includes vaporized products from the immobile oil in addition to oil produced by displacement. If a large part of the immobile oil is vaporized, total oil recovery may be higher than that obtainable from pressure maintenance by water injection. However, the amount of immobile oil vaporized may range from almost 0 to 100 percent, and no simple and reliable method has been presented in the literature for calculating oil vaporization. Development of such a method was the purpose of this study. Several papers concerning the calculation of oil vaporization have been published,3 6 and each is based on the concept dealing with K values — equilibrium constants for the various components in reservoir oils. (K for a component in a system of vapor and liquid in equilibrium is the mole fraction in the vapor phase divided by the mole fraction in the liquid phase.) This appears to be the most logical approach. Yet, the problem is too great for a perfect solution, even with modem laboratories to analyze oils and high-speed digital computers to perform calculations; the number of components in reservoir oils is too large. Because of their complexity no two reservoir oils are exactly alike. Also, K values change not only with variations in pressure and temperature but also with composition of the reservoir oil. In addition, during gas cycling, the lighter hydrocarbons tend to vaporize first. Thus, the reservoir oil becomes more dense and less volatile as gas cycling continues. Furthermore, the greatest amount of oil vaporization occurs near the injection well. Therefore, a simplified method is required for calculating oil vaporization because a rigorous method is not practical. The present methods of calculating vaporization generally require knowledge of the reservoir oil composition in which the mole fractions of the lighter components through hexanes are given; the remaining oil is described as C, + (heptanes and others of greater molecular weights). Assigning one K value for the C,+ system provides the simplest solution, but this incorrectly assumes that K for C, + does not change as gas cycling continues. This assumption can cause large errors because the K value may become less than a thousandth of the original after a large amount of oil vaporization. Another way to solve the problem is to determine changing K values for C, + according to how much of the C, + has been vaporized. To determine these values a sample of the reservoir oil is injected into a pressure-volume cell, and dry gas is batched in and out of the cell. Appropriate measurements and tests are made to determine K

Jan 1, 1970

By R. H. Jacoby, M. J. Rzasa

Experimental equilibrium vaporization ratios (K values) were obtained for nitrogen, methane, carbon dioxide, ethane and hydrogen sulfide in two natural gas-absorber oil mixtures and in two natural gas-Elk Basin crude oil mixtures. For each mixture of constant over-all composition, data were obtained at 100°, 150° and 200°F and at various pressures in the range 200 to 5,000 psia. Some effects of composition on the K values were obtained to serve as a guide in choosing K's for engineering calculations on other mixtures. The pressure cell used to obtain the data is a new type and is described here for the first time. INTRODUCTION The phase equilibria of complex hydrocarbon mixtures such as natural gases, crude oils and their mixtures have been studied previously for the purpose of finding equilibrium vaporization ratios for the hydrocarbon constitutents. In a few cases, such non-hydrocarbon.: as nitrogen, carbon dioxide, and hydrogen sulfide were included in the mixture. studied because they occur. in the fluids obtained from petroleum reservoirs. The increasing occurrerce. of these non-liydrocarbon.; antl their growing economic importance. make it necessary to account for them more accurately in engineering calculation.: than is now possible using the meager published data. The available data for non-hydrocarbons may he classified into two groups: namely, binary mixtures of a hydrocarbon and a non-hydrocarbon. and mixtures containing three or more components, only one of which is a non-hydrocarbon. Amon: the former. phase analyses are available for two nitrogen-HC mixtures, tve carbon dioxide-HC mixtures and three hydrogen sulfide-HC mixtures. Data for more complex mixtures are available as follows: Nitrogen-Methane-Pentane'; Nitrogen-Methane-Hexane,'; Nitrogen-Methane-Heptane'; Carbon dioxide-Natural Gas-Natural Gasorline": Carbon dioxide-Natural Gas-Crude Oil". These data have been used generally lor engineering calculations, often with little regard for their precise applicability because data for the non-hydrocarbons in the complex mixtures being dealt with were not available. The use of K values from binary data for calculation:; involving complex mixtures is open to criticism because such K's are not a function of composition and very often show large differences from the K's for the same components in a complex mixture. Thus the effects of composition must be evaluated when obtaining K's for components in complex mixtures. Poettmann and Katz " varied the carbon dioxide content of their mixture.; from about five to ten mol per cent and found substantially no effect on the K values due to this change. This was not surprising since one might expect that changing a minor com-ponent by * three mol per cent would have little effect. It is more important to find the composition change which have the largest effect on the K values. For example. varying the methane or heptanes — plus compositions over a wide rangr may have a large effect on the K'. of all components in the mixture. Interesting data to this effect were obtained by Eilerts and Smith." It was toward these problems that the experimental data presented here were directed. EQUIPMENT The pressure cell used to obtain the data i:. somewhat dif-ferent from those which have been described in the past. Photographs of the equipment are shown in Figs. 1 and 2. Fig. 1 Shows. the front panel: from a .rated position at the right the

Jan 1, 1952

By T. V. Philip, Paul A. Beck

IN a previous note1 it was pointed out that the available information suggests a distinct correlation between the occurrence of the CsCl-type ordered structures formed in equi-atomic binary alloys of transition elements and the location of the components in the periodic table. A definite increase in the bond strength between unlike atoms, as compared with that between like atoms, is indicated when, in binary alloys of iron group elements, the other component is changed from chromium to vanadium or tantalum, to titanium. Laves and Wallbaum,2 eported a CsCl-type ordered structure for the stable intermediate phase at the equi-atomic composition in the Ti-Fe system (and also in the Ti-Ru and Ti-Os systems). On the other hand, Tagaya, Nenno, and Nishiyama8 found no ordering of this kind in the body-centered-cubic solid solutions in the Cr-Fe system. It was concluded' that the occurrence of a CsC1-type ordered phase of intermediate stability may be expected in the V-Fe system. Preliminary results were described: suggesting that at least some degree of order does exist in the equi-atomic alloy VFe, annealed at 1200° C and quenched in cold water. Using CrK radiation, at least one weak superlattice line was found in the X-ray diffraction pattern which could be indexed as (100). and which disappeared, as expected, when FeK radiation was used. It was found more recently that the impurity phase (presumably VN), previously giving rise to additional X-ray diffraction lines and thus preventing definite indentification of the (111) superlattice line,' can be eliminated by preparing the alloy by arc melting in a helium atmosphere. The alloy specimen melted in this manner had clean surfaces and showed very littte, if any, nitride phase in the microstructure after annealing in vacuum at 1250°C and quenching. The relative intensity of the (100). superlattice line with CrK radiation was greatly increased and, in addition, a fairly strong (Ill) , superlattice line and even a detectable (210) , super- lattice line was obtained, when the powder produced by filing from the 1250°C annealed and quenched specimen was reannealed in vacuum at 625°C for 1 hr. By using a cellulose acetate film as a filter in front of the photographic film in order to absorb the soft radiation resulting from air fluorescence, the background intensity could be reduced considerably in relation to the intensity of the diffraction lines. All three superlattice lines, (100),, (111)., and (210)a, disappeared, as expected, when a radiation other than CrK, was used.1 For the powder reannealed at 625ºC, the strongest lines of the s pattern also appeared weakly, indicating that during an: nealing at 625°C a small amount of transformation took place from the body-centered-cubic to the u phase. However, since all superlattice lines to be expected in the 0 angle range used were actually very clearly present, it was evident that the high temperature body-centered-cubic phase had transformed into a CsCl-type ordered structure before much s phase could form. Reannealing filings for 1 hr at 700°C resulted in complete transformation into the u phase. After 1 hr at 650°C the transformation into IT was not quite complete, the strongest body-centered-cubic diffraction lines were still present, although fairly weak, and only the (100), super-lattice line was detectable (extremely weak). These findings not only confirm the previous conclusionsL as to the existence of a CsCl-type ordered structure in the Fe-V system, but they also indicate that this metastable ordered structure forms at about 600°C preceding the formation of the stable s phase, while at 1250°C the disordered body-centered-cubic phase is stable. The faint (loo) , super-lattice line previously observed in specimens quenched from 1200°C was probably due to the fact that the quenching of the powder in an evacuated fuse:! quartz capsule was not fast enough to prevent completely the ordering reaction on cooling. The present results conform with the suggestion that the A-B bond, in relation to the A-A and B-B bonds, increases in strength from CrFe to VFe to TiFc. It is, therefore, of interest to compare the measured values of the average atomic diameter for these three alloys with the corresponding average atomic diameters calculated from the atomic radii of the elements concerned. ASSUming A-B contacts

Jan 1, 1958

By G. B. Craig, H. E. Rosinger, W. J. Bratina

NUMEROUS studies have been reported on how the mechanical properties of a bcc metal are affected by interstitial solute atoms in the temperature range where appreciable diffusion occurs in finite time. Only recently, though, has work on an "interstitial-free" iron been reported, this by Leslie and sober,' on an Fe-0.15 pct Ti alloy. The data was limited to a maximum temperature of 296°K. This work presents a systematic study of the flow stress and the activation volume of a similar material as a function of plastic deformation over the temperature range 253" to 473°K. The material studied was Ferrovac E iron containing 0.01 wt pct C and 0.0002 wt pct N annealed at 870°C for 1 hr, and the same iron with an addition of 0.15 wt pct Ti annealed at 870°C for 80 hr; cooling rates being 75°C per hr. In the latter alloy depletion of interstitials in the a-iron matrix associated with the second phase formation was expected. The temperature dependence of the flow stress was measured at 6 = 3.33 x 10-5 sec-1 from 253" to 473°K as a function of the deformation in 0.01 intervals from 0.03 to 0.12 strain. Results for two strains, 0.03 and 0.09 are shown in Fig. 1. The flow stress increased and reached a maximum in the Ferrovac E iron with increasing temperature, but showed a consistent gradual decrease in the Ferrovac E-0.15 pct Ti alloy. A yield point and Luders region, observed in Ferrovac E, was absent in the Ferrovac E-0.15 pct Ti alloy. Also, the Ferrovac E exhibited a serrated stress-strain behavior in the temperature range 330" to 400°K; dynamic strain-aging characteristics were absent for the titanium alloy. The activation volume was determined over the same temperature range by the method of stress relaxation at constant strain. Results are shown in Fig. 2. At the temperatures of serrated stress-strain behavior in Ferrovac E the activation volume was found to increase toward infinity and, as the temperature rose, to decrease, to about 100 to 200 v/b3. By contrast, the activation volume for the Ferrovac E-0.15 pct Ti alloy tended to increase continuously from the initial value of approximately 300 at 300°K to more than 800 at 473°K. Above 400°K, then, the corresponding activation volume values of Ferrovac E were less than that of the Ferrovac E-0.15 pct Ti alloy. The activation volumes, Fig. 2, appear to depend on dislocation-interstitial interaction in Ferrovac E and on dislocation-dislocation interaction in Ferrovac E-0.15 pct Ti alloy. The gradual increase in the latter metal is associated with thermally activated motion of dislocation segments.' The decrease of the activation volume in Ferrovac E above 400°K is probably related to the diminishing effect of interstitials on dislocations. Here, the interstitials can be moved along with a dislocation without appreciable drag. As indicated in Fig. 1, removal of interstitials

Jan 1, 1970

By M. D. Banus, M. B. Bever, A. K. Jena

The heals of formation at 78", 195, and 273°K of the ternary compound h3SbTe2 based on the elements and based on the binary compounds In Sb and [inTe have been measured. The heats of formation at these temperatlcres of the binary compounds In Sb and In Te based on the elements have also been determined. Heal contents and free energies of the three compounds have been calculated from 0° lo 80I)°K. The free energies of joyrrzalion, heats of formations, and entropies of formation at 298°K have also been calculated. The results shown that the tertnary compound is metastable with vespecl to InSh and ln Te below 696 °K. bul is slable above that temperature. The weaker bonding of results in a positice entropy of formation which with incrensirzg temperature makes increasing negative conlvihtclions to the free energy and above 696°K renders the compound slable. THE ternary compound In3SbTez occurring in the quasi-binary system In Sb- In Te' forms on cooling at 829°K by a peritectic reaction.' Observations at 673" and 573 K have shown that this ternary compound decomposes slowly into the binary compounds InSb and1n~e.l'' It has not been possible to analyze the metastable behavior of the ternary compound because up to the present time data on its thermodynamic properties have been lacking. Some information on the binary compounds, however, is available. The heat of formation of InTe at 273°K and its free energy at 673°K are kn~wn.~'~ The heats of formation of InSb at 78", 273', 298", and 723°K have been measured5-' and its heat capacity between approximately 12" and 300"Kg9l0 is also known. In the investigation reported here the heats of formation at 78% 195% and 273°K of the ternary compound In3SbTez have been measured. The heats of formation of the binary compounds InSb and InTe at these temperatures have been obtained by combining new calorimetric results with previously published data. The heat contents and free energies of the three compounds at various temperatures from 0" to 800°K have been calculated. Against the background of this information, the metastability of the ternary compound will be discussed. 1) EXPERIMENTAL 1.l) Preparation of Specimens. The materials used consisted of the elements indium, antimony, and tellurium, the binary compounds InSb and InTe, and the ternary compound In3SbTez. The elements, obtained from American Smelting and Refining Co., had a nominal purity of 99.999+ pct. The compound InSb was Cominco semiconductor grade; the compound InTe was prepared from the elements by melting under a vacuum of 10-h m Hg followed by slow cooling. Three batches of specimens of the compound In3SbTez were used. One batch was prepared by melting appropriate amounts of the elements in an evacuated and sealed Vycor tube. The melt was held at approximately 100°K above the liquidus for about 8 hr, shaken repeatedly, and quenched into a mixture of ice and water. The specimen was annealed in vacuum at 760°K for 4 weeks. In preparing a second batch, a mixture of the component elements was melted and quenched in water. The resulting ingot was powdered. The powder was pressed into pellets, which were annealed in vacuum at 748" to 773°K for 4 weeks. A third batch was prepared in the same manner as the second, except that the starting materials were InSb and InTe rather than the elements. Metallographic examination of samples of the three batches and X-ray diffraction examination of a sample of the second batch did not reveal evidence of microsegregation or a second phase. The results obtained with the three batches showed no systematic differences. 1.2) Calorimetry. The calorimetric method has been described in detail." Samples of the compound In3SbTez, mechanical mixtures of InSb and InTe in the proportion of 1:2, and mechanical mixtures of indium, antimony, and tellurium in the proportion of 3:1:2 were added to a bismuth-rich bath at 623°K in a metal-solution calorimeter. These additions were made from 78°K (liquid nitrogen), 195°K (dry ice and acetone), and 273°K (ice and water). The heat effects of the additions were measured. The difference in the heat effects of the additions of a compound and the additions of the mixtures of its constituents, adjusted for differences in the concentration of the bath, is the heat of formation of the compound. In the concentration range not exceeding 1.5 at. pct solute, the heat effect of the additions was a linear function of concentration. The heat of formation refers to the temperature from which the additions were made, namely, 78", 195", or 273°K. Several calibrating additions were made in each calorimetric run. The calculated heat capacity of the calorimeter and hence the calculated heat effects of the additions of samples depend upon the values adopted for the heat contents of the calibrating substance. In this investigation bismuth at 273°K was used and a value of 4.96 kcal per g-atom was taken for (HGZ3"k . 2) RESULTS AND DISCUSSION 2.l) Heats of Formation. The heats of formation of the ternary compound In~SbTez from the component elements indium, antimony, and tellurium and from

Jan 1, 1968

By B. Ramaswami, U. F. Kocks, B. Chalmers

This paper describes the tempetrature, solute (gold), and orientalion dependence of the plastic rleforlirnlion of silver single crystals. The virgin flow stress, To, and its temperatutre dependence incrense with increase in solute concentration. el decreases with decrease in temperature below room teiirperature and with increase in solute coucentralion. The dependence of 011 on temperature arid solute sontenl is due to the dependence of Ts on the two variables. An increase in ts, due to either the temperature or the solute conlent, results in a decrease of e11 in crystals of single-slip orientation and an increase of 011 in crystals of' (100) find (111) orientation. is orientation-dependent and at all the temperatures and in all the materials studied. The Leveling off of the engineering stress-strain curve in crystals of (100) 07-ientotion at a stress tl, is associated with extensive cross slib. The temperature and strain -rate dependence of tl are similar to those of indicating that a rate process is the cause 01 this phenomenon. The plastic deformation of silrer crystals of (110) orientation is multiple to that of crystals of single-slip orientation. THE work hardening of fcc crystals has been the subject of intensive investigations in the past 15 years. The effect of orientation, deformation temperature, solutes, second phase or precipitates, strain rate, etc., has been studied in a number of fcc metals.'-5 In spite of the considerable amount of work reported on the dependence of work hardening on the orientation, temperature, and solute concentration, certain aspects of the plastic deformation of fcc crystals have not been clarified. For instance, with the exception of a few investigations,6-8 where crystals of multiple-slip orientations have been studied, almost all the studies have been on crystals of single-slip orientations. Hence, a major portion of this study has been devoted to the dependence of plastic deformation on the multiplicity of slip systems and the enhanced possibility of dislocation interactions resulting from such multiplicity. Further, the abnormally low rate of work hardening observed at large strains at certain temperatures in crystals of the (100) orienta-tion 6-8has not been explained satisfactorily. It is the aim of this study to clarify this aspect of the orientation and temperature dependence of the plastic deformation of fcc single crystals. The work-hardening characteristics of single crystals of aluminum of ( 110) orientation have been studied at room temperatur "'12 and above." They have not been studied at temperatures where the virgin flow stress is dependent on temperature or where, in Seeger's terminology is important. The work hardening of single crystals of (110) orientation is of interest for another reason. As shown in Table I, the dislocation reactions that are possible in the (110) orientation are similar in certain respects to those that are possible in the (100) orientation. Hence, the deformation of single crystals of silver of (110) orientation was studied in the temperature range 100° to 900°K at intervals of 200°K. The effect of solute concentration on the plastic deformation of fcc single crystals of single-slip orientation has been studied by several investiaators.> In all of these investigations—with the exception of Ref. 20—single crystals of identical orientation have not been used, with the result that the orientation dependence of plastic deformation is superimposed on the effect of the solute. In addition, the effect of the solute on the work-hardening characteristics of single crystals of multiple-slip orientations has not been studied by the previous

Jan 1, 1965

By W. E. Horst

Flotation feed was hell constant for batch laboratory tests and continuous pilot and commercial plant tests on a spodumene ore to determine the relation.ship between flotation behavior and the size and type of flotation machine. Results. showed that additional retention time would be needed in the plant flotation circuit to duplicate laboratory or pilot plant performance when operating Dariables of the. plant flotation machines remained unchanged. During the past few years of operation at Kings Mountain, N. C., full-scale flotation has generally yielded poorer metallurgical results than those obtained in the laboratory or pilot plant. After 2 min in each size of Denver flotation machine in the spodumene rougher circuit, pilot recovery (41.7 pct) was almost three times that of the plant (13.6 pct) and about twice that of the laboratory (21.0 pct). Pilot and commercial plant data are based on continuous operation, and laboratory results on batch testing of rougher performance. The ore is a pegmatite containing spodumene, feldspar, quartz, mica, and amphibolite. Data were accumulated to evaluate the scale-up relationships between laboratory, pilot plant, and plant flotation cells. Flotation rate constants and dimensional analysis were used to define the relationship existing between flotation behavior and scale of operation. Measuring Flotation Rates: Efficiency of the rougher stage was measured by flotation rate, defined as the recovery that can be attained within a given time." • The problem of measuring flotation rates has been studied by many investigators, whose methods have varied. Published studies an flotation kinetics have been summarized recently by Gaudin.l When comparing flotation rates, it is more satisfactory to compare straight line relationships between recovery and flotation time than exponential curves resulting from plotting cumulative recovery vs cumulative flotation time. To convert the exponential curves into straight line relationships, rate equations were applied similar to those used in chemical kinetics to study the velocity of chemical reactions. Two rate equations have been used in this investigation to measure efficiency of the various cells: 1.5 order Rate Equation dR/dt=k (A-R)1.0 [Eq.1] Second Order Rate Equation dR ---- - K(A - R)2 [Eq. 2] dt Upon integration Eq. 1 becomes 1/(A-R)1/2=k/2 t+1/A1/2 [Eq. 3] and Eq 2 becomes: or fEq. 4] t/R=1/A2K+t/A [Eq. 4] where R = cumulative recovery [percent recovery of total value (spodumene) in flotation feed]. A = initial concentration, pct (100 pct of mineral to be separated). t = flotation time (minutes). k = flotation rate constant for 1.5 order rate equation [units: 1/(percent) 0.5 (min)1. K = flotation rate constant for second order rate equation [units: 1/(percent) (min) 1.

Jan 1, 1959

By C. L. Sollenberger, R. B. Greenwalt

PERHAPS the most widely used dispersants or gangue depressants in nonmetallic flotation are sodium silicates, which vary in silica-to-soda ratio from 1 to 3.75. Typical manufactured silicates in order of decreasing solubility and increasing amounts of silica are Metso, silica-to-soda ratio of 1.00; D, 2.00; RU, 2.40; K, 2.90; N, 3.22; and S-35, 3.75.* References in flotation literature's to the use of sodium silicates are often weak because they fail to mention the type of silicate used. Metso and silicate N have occasionally been mentioned, but when the type of silicate is not mentioned, it is usually assumed to be N, the cheapest of the soluble silicates and the one recommended by sodium silicate manufacturers as a flotation agent.

Jan 6, 1958

By O. L. Culberson, J. J. McKetta

INTRODUCTION The equilibrium constants for methane and for water, and for ethane and water have been calculated from experimental data for the two binary systems.2,3,11,12 These constants are for the two-phase systems for the temperature range of 100" to 340°F and the pressure range of 200 to 10,000 psia. The constants for ethane are greater than those for methane. Equilibrium constants for a natural gas from a natural gas-water system6 are about the same as those for methane. Equilibrium constants for water in all three systems are very nearly the same over the greater part of the range of temperatures and pressures studied. In ideal solutions, the vapor-liquid equilibrium constants for a component should be the same in all such solutions at a given temperature and pressure.5 Few solutions are ideal, and consequently the use of generalized constants often leads to error in situations where they do not actually apply. In decidedly non-ideal systems, it is desirable to have equilibrium constant data for the specific system. Vaporization equilibrium constants may be calculated either by thermodynamic methods or from experimental vapor-liquid equilibrium data. In the thermodynamic calculation. the equilibrium constant K may be shown to be" K = fP,/fl'..........(1) where fPi is the fugacity of the pure component i at the given temperature and at the vapor pressure of the pure component, and fp is the fugacity of pure i in the gaseous state at the temperature and total pressure of the system. At best the thermodynamic calculation results in a K applicable to ideal solutions. Equilibrium constants calculated from Equation (1) have been found to have only limited agreement with experimental values, even though the solutions for which they were calculated approached ideality."'" If the more volatile component is at a temperature above its critical, the accuracy of the equilibrium constant for the component is made more doubtful by the use of the vapor pressure term under such conditions. In order to make the thermodynamic calculation on a component above its critical temperature, one must resort to one of the empirical methods of extrapolation of the vapor pressure to conditions above its critical point.13 Application of the thermodynamic equilibrium constant then to the methane-water or the ethane-water systems would be risky since the systems are non-ideal, and the methane and ethane are above their critical in most petroleum operations. ETHANE-WATER SYSTEM In the temperature range of from 100° to 340°F and for pressures up to 10,000 psia, the vapor-liquid equilibrium data 'References given at end of paper. Manuscript received in the office of the Petroleum Branch March 16, 1951.

Jan 1, 1951

By J. J. McKetta, O. L. Culberson

INTRODUCTION The equilibrium constants for methane and for water, and for ethane and water have been calculated from experimental data for the two binary systems.2,3,11,12 These constants are for the two-phase systems for the temperature range of 100" to 340°F and the pressure range of 200 to 10,000 psia. The constants for ethane are greater than those for methane. Equilibrium constants for a natural gas from a natural gas-water system6 are about the same as those for methane. Equilibrium constants for water in all three systems are very nearly the same over the greater part of the range of temperatures and pressures studied. In ideal solutions, the vapor-liquid equilibrium constants for a component should be the same in all such solutions at a given temperature and pressure.5 Few solutions are ideal, and consequently the use of generalized constants often leads to error in situations where they do not actually apply. In decidedly non-ideal systems, it is desirable to have equilibrium constant data for the specific system. Vaporization equilibrium constants may be calculated either by thermodynamic methods or from experimental vapor-liquid equilibrium data. In the thermodynamic calculation. the equilibrium constant K may be shown to be" K = fP,/fl'..........(1) where fPi is the fugacity of the pure component i at the given temperature and at the vapor pressure of the pure component, and fp is the fugacity of pure i in the gaseous state at the temperature and total pressure of the system. At best the thermodynamic calculation results in a K applicable to ideal solutions. Equilibrium constants calculated from Equation (1) have been found to have only limited agreement with experimental values, even though the solutions for which they were calculated approached ideality."'" If the more volatile component is at a temperature above its critical, the accuracy of the equilibrium constant for the component is made more doubtful by the use of the vapor pressure term under such conditions. In order to make the thermodynamic calculation on a component above its critical temperature, one must resort to one of the empirical methods of extrapolation of the vapor pressure to conditions above its critical point.13 Application of the thermodynamic equilibrium constant then to the methane-water or the ethane-water systems would be risky since the systems are non-ideal, and the methane and ethane are above their critical in most petroleum operations. ETHANE-WATER SYSTEM In the temperature range of from 100° to 340°F and for pressures up to 10,000 psia, the vapor-liquid equilibrium data 'References given at end of paper. Manuscript received in the office of the Petroleum Branch March 16, 1951.

Jan 1, 1951

By D. W. Fuerstenau

In 1940 Schuhmann1 showed that the size distribution of a comminuted material can be expressed by the following empirical relationship: y = 100 (|f [i] where y is the cumulative percentage of material finer than size x, k is a size modulus, and a is a distribution modulus which is constant for a given material and machine. During the past few years, considerable emphasis has been given to the investigation of the extent of size reduction resulting from the expenditure of mechanical energy in crushing and grinding. Recently Schuhmann' presented a derivation of the energy-size reduction relationship by postulating that comminution in a device such as a ball mill can be considered to be the summation of many single comminution events, each of which yields a size distribution of particles following the Schuhmann size distribution equation. By grinding

Jan 1, 1961

By Reuben B. Ellestad, Fremont F. Clarke

Lithium chemical plant extraction methods are discussed with reference to 1) base exchange with alkali sulphates; 2) processing based on roasting with lime; 3) miscellaneous methods; and 4) application of the Lithium Corp. process to extraction of lithium from run-of-mine, low grade spodumene ore, or concentrates. IN the early days of the lithium industry most of the production was from lepidolite, zinnwaldite, and amblygonite. Nearly all the early extraction processes described in the literature involve heating the finely ground mineral with sulphuric or hydrochloric acid. On subsequent water leaching most of the bases present in the mineral (especially aluminum) are dissolved as sulphates. As a result, the leach solution required extensive chemical purification before the lithium could be precipitated as carbonate. Following the remarkable growth of the lithium industry to its present size, zinnwaldite and amblygonite ores must be considered of minor importance only. Attention is now focused on spodumene, abundant enough in North America to be a major source of supply, and there are important supplies of lepidolite and petalite in Africa. The extraction processes described below all apply to spodumene, although several will also operate on other lithium minerals, such as petalite. Base Exchange with Alkali Sulphates: A distinct advance was made with the disclosures of Wadman and von Girsewalt. In these methods the finely ground silicate ore (spodumene or lepidolite) is intimately mixed with an excess of alkali sulphate (usually K2SO4) in at least a 1 to 1 proportion, and the mixture was heated to a relatively high temperature. Base exchange results, with the formation of lithium sulphate. A water leach dissolves the lithium sulphate, together with the excess potassium sulphate. Successful operation of this type of process requires very thorough grinding and mixing, as well as careful temperature control. The use of K2SO4 is objectionable from cost considerations since purification of lithium carbonate requires the use of potassium carbonate, if the K2SO4 is to be recovered and recycled. The lower solubility of K2SO4 as compared with Na2S04 is also objectionable, since it limits the concentration of the Li2SO4 solution to be precipitated by K2SO4. Early laboratory-scale investigation of this process by Lithium Corp. was not encouraging. Other related base exchange processes are those of Lindblad, Wallden, and Sivander3 and Sivander, Gard, Villestad, and Wallen4. The former covers the reaction of lithium silicate minerals with a sodium sulphate solution, at 100" to 300°C (under pressure), while the latter involves the extraction of silicate minerals with molten sodium sulphate. Both these processes would seem to be difficult and expensive to operate.

Jan 1, 1956

By Yoichi Ishida, Ching-Yao Cheng, John E. Dorn

Tile creep behavior of a iron was investigated over the range of temperatures from 375° to 1150°K. Apparent activation energies for creep, obtained by the effect of sudden changes in temperature on the creep rate, revealed the presence of- four distinguishable regions. The creep behavior of a iron in Regions II (480° to 774°K) and 111 (775° to 1045°K) was found to correlate well with a model where the creep rate is controlled by the nonconsevualive motion. of jogged screw dislocations. An anomalous increase in the apparent activation energy fur creep in Region III was found to be in harmony with the known decrease in the free activation energy for self-diffusion over the Curie transformation range. Furthermore, the creep rates in Regions II and III were found to increase with stress due not only to the effect of stress on the activation energy but also to an increase in density of mobile dislocations. The evidence suggests that pipe diffusion along moving dislocations could be a significant factor over the lower temperatures of Region II. ALTHOUGH the creep properties of iron and steel have been of interest to metallurgists for some time and an extensive literature is now available, most of the published information has not produced much toward understanding the fundamental dislocation processes controlling the creep behavior of these materials. Whereas the activation energy for high-temperature creep of metals usually agrees well with that for self-diffusion, Sherby, Orr, and Dorn1 deduced from the data of Tapsell -and c1enshaw2 that the activation energy for creep of Armco iron is about 78,000 cal per mole and more recently Lytton and sherby3 reviewed the data of Jenkins and Mellor4 and found an activation energy for creep of a iron of 80,000 cal per mole. Both values are substantially greater than the activation energy for self-diffusion in a iron. Because of the limited data suitable for purposes of identifying the controlling dislocation mechanisms of creep and the unusually high activation energies for creep quoted above, it was considered desirable to reinvestigate in detail the creep of a iron by more reliable techniques which would provide sufficient data for determination of the creep mechanisms. EXPERIMENTAL TECHNIQUE Creep specimens were prepared from 3/8 by 4 in. iron bar stock of the following composition by weight percent: 0.001 C, 0.0120 0, 0.001 N, 0.004 S, and 0.003 P. The as-received bars were cold-rolled to a thickness of 0.100 in., annealed under argon for 30 min at 1113°K, cold-rolled to a final thickness of 0.063 in., and machined into tensile specimens having gage section 0.250 in. wide and 1.70 in. long. Finally they were recrystallized under argon at 1113°K. Specimens to be crept above 1060°K were recrystallized at 1173°K. Both recrystallization treatments gave the same reproducible equiaxed ASTM No. 4 grain size. Creep testing was conducted in machines fitted with Andrade-Chalmers arms that maintained a constant stress to within ±0.2 pct of the reported values. Deformation over the specimen gage section was sensed with a linear differential transformer and recorded auto-graphically as a function of time. The strains deduced from these measurements were sensitive to ±5 x 10-5. During creep the specimens were contained in an argon-filled chamber which was immersed in a temperature-controlled molten tin bath. Creep temperatures, as measured by thermocouples attached to the specimen, were maintained to within ±10.25°K of the reported values. For activation-energy determinations rapid changes in temperature of about 12°K were obtained within 30 sec by direct resistance heating of the creep specimen, and maintained to ±1°K of the reported values. Observations of structural details of specimens before and after creep tests were made by electrolytic polishing and etching in acqueous ammonium persulfate. EXPERIMENTAL RESULTS A typical example of the determination of apparent activation energies, Q, by the effect of small changes in temperature is illustrated in Fig. 1. Q is defined by

Jan 1, 1967

By K. Tanaka, J. D. Mote, J. E. Dorn

It) an attempt to ulLcoce.lP the operative strain-rate-contl-olliy: dislocation nieclzanistns, specially oviented sizgle clystals of the intel-nzediate 1zexagonal phase containing Ag plus 33 at. pct A1 were tested in tension over a wide range of temperatures. Slip was observed to take place by the {0001} <1120> {l100} mechani fracture took place across the(i100) plane and winning occurred by the (i01Z) ?lechanisn. Basal slip exhibited a strong yield point over the -alzge from 77 to 450°K, the upper ,esolved shear st]-ess having the exceptionally high value of 10,500 psi over this entire ?-a?zge of tenzpei,atuves. The critical 9-esolved shear stress for prismatic slip decreased f7-om 48,000 psi at 4.3"K to 23,000 psi at 170°K (Region 1) follozcirg zt:lzich it decl>eased sloz&ly to 21,500 psi at 475°K (Res&apos;on II); from 475" to 575°K (Regioz III), the c7-itical esolced shear stress dec&apos;-eased precipitously to 2000 psi; and from 575" to 750°K (Region IV) it decreased less afi&apos;dly to a low value of about 500 psi. Pvistintic slip in Region I was pobably controlled by the tliel-nally activated riecharzisui of nucleation and g,-ozcth of kinks in dislocations lying in Peierls potential troughs. In Region II for prismatic slip the critical 1-esolved shear stress was slzocn to be deteemined by sh0l.t-range 01-dering, Overall the forgiorz fo basal slip, 7.c.lre1-e a Strong yield-point phenorlienu ia7as observed, the critical vesolved slzea?-stress was shoztn to be determined by n conibirzation 0-f Szizuki locking and short-range-order Izavderzizg, The precipitous decrease in the critical resolved shear stress with increase in ter,/pe7-atrir-e over Region HI was tentatively ascribed to a decrease in the degree of slort-)ange 07-del;iqq (0)- clusteing) and also the effect of fluctuations the degree of o?der, It is at pgreser2t zrtzce)taitz as to 1t1hethe1- these or other possi1)le effects are also ,esponsible. fo- the data obsel-ved 172 Region IV. 1NTEREST in inter metallic compounds stems not only from their role in dispersion hardening of polyphase alloy ystems but equally from their potentialities for high strength, hardness, and stability not only at atmospheric temperatures but especially at elevated temperatures. As summarized in a re- cent symposium of the Electrochemical Society on "Mechanical Properties of Inter metallic Compound", most of the experimental evidence regarding the mechanical behavior of intermetallic compounds centers about the effect of temperature on the hardness and ductility of polycrystalline specimens. The available data reveal that the plastic behavior of intermetallic compounds might be rationalized in terms of the usual dislocation mechanisms appropriate to a solid solutions providing the additional complexities arising from crystal structure, long-range ordering, short-range ordering, and defect lattices are taken into consideration. It is apparent, however, in terms of the history on a solid solutions, that a complete detailed mechanistic rationalization of dislocation processes may not be possible until the deformation processes are studied in single crystals of intermetallic compounds. The present paper contains a preliminary report on the plastic behavior of single crystals of the hexagonal Ag-A1 intermetallic phase over a wide range of temperatures. The results confirm the thesis that single crystal data provide a most effective method of identifying operative dislocation mechanisms in intermetallic compounds. EXPERIMENTAL TECHNIQUES Several factors prompted the selection of the hexagonal Ag-A1 intermetallic phase for this preliminar investigation on the plastic properties of single crystals of intermetallic compounds: 1) This phase has a wide solubility range5 which would permit future investigations on the effect of composition and axial ratios on slip mechanisms. 2) Although it undoubtedly exhibits short-range ordering (or clustering) this intermetallic phase is free from complexities arising from long-range ordering.6 3) Since the atomic radii of aluminum and silver are practically identical, the possible complications due to Cottrell locking are minimized. 4)Whereas the dislocations on the basal planes are expected to dissociate into Shockley partials and are thus susceptible to Suzuki locking, those on the prismatic planes probably remain complete. 5) The axial ratio, being 1.61, is almost ideal, suggesting that short-range ordering may be almost spherically symmetrical. The present investigation was conducted exclusively with the hexagonal Ag-A1 alloy containing 33 at. pct Al. Preliminary investigations revealed that this alloy undergoes basal slip by the (0001)

Jan 1, 1962

By W. Luyken

A NUMBER of articles have been published, notably those by R. S. Handy, R. T. Hancock and A. P. Watt in Engineering and Mining Journal, dealing with the calculations involved in ore dressing.. These publications demonstrate both, the importance of the subject and the lack of success in developing a generally recognized method for comparing enrichment effects. Considering that we may wish -to compare enrichment results on similar or dissimilar ores, that we may desire to make the comparison on the basis of either the absolute or the economical efficiency, and that the number of factors upon which the result depends is large, the question arises whether it is possible to set up a positive method for such calculations. In the following pages it is our aim to show that a sure, complete and successful way to overcome existing difficulties has been found. GRAPHICAL ANALYSIS OF ORE-DRESSING PROCESSES The following is from Truscott&apos;s Text Book of Ore Dressing (London, 1923) x = assay of ore treated (feed). y = assay value of the concentrate. z = assay value of the tailing. a = weight of feed. b = weight of concentrate. c = weight of tailing. C = fractional concentration = b/a= x-z/y-z (1) K = ratio of concentration = 1/C = a/b =y-z/x-z (2) R = fractional recovery = yb/xa = Cy/x. (3) 100R = percentage recovery. Copt = theoretically best concentration. 100 - Copt = waste in the feed.

Jan 1, 1929