Search Documents

By Alexander May

The Bureau of Mines conducted studies to determine if phosphogypsum, a waste material from the processing of phosphate rock, contains hazardous toxic materials as defined by the Environmental Protection Agency (EPA) and whether leaching of these toxic materials and radium may occur. Samples of the phosphogypsum stockpiled material were evaluated using the EPA extraction procedure, atomic absorption, neutron activation, x-ray diffraction, and chemical and physical means. Radiological tests performed used both the germanium-lithium and emanation methods. The data show that the phosphogypsum stockpiles are not hazardous toxic waste as defined by EPA criteria. Trace elements and radium are not leached from the phosphogypsum stockpiles. Absorption of trace elements and radium by phosphogypsum is the major reason for their not being leached. The standard error of measurement of radium concentrations was 4.7 pCi/g.

Jan 1, 1983

By Henry Louis

THE work performed by the Royal Commission on Mining Subsidence is likely to prove of permanent value, less perhaps for the conclusions it has reached and for the recommendations it has based upon these than for the admirable exposition which it affords of the law concerning mining subsidence and of the legal status of the person who has suffered damage by reason of such subsidence, as also of him whose working has caused the damage. The Commission was appointed by Royal Warrant in the middle of 1925 and delivered its final report in the middle of 1927. The terms of reference to the Commission were as follows: "To consider the operation of the law relating to the support of the surface of the land, and of buildings or works on or under the surface, by underlying or adjacent minerals; to enquire into the extent and gravity of the damage caused by subsidence owing to the extraction of minerals and the incidence of the resulting liability; and to report what steps should be taken, by legislation or otherwise, to remedy, equitably to all persons concerned, any defects or hardships that may be found to arise in existing conditions."

Jan 1, 1929

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.

By Steven Gillgrass

Gerdau Monroe has installed and commissioned the Tallman Supersonic Carbon Injection system (TSCi™) for use in their 135-ton Electric Arc Furnace (EAF) located in Monroe, MI. TSCi™ is an innovative injection system with the primary aim of improving injection carbon delivery to the steel bath by increasing efficiency. It is proven technology with installations at numerous steelmaking facilities all over the world. Results from installation and commissioning of TSCi™ at Gerdau Monroe will be reported as well as on-going trials and optimization efforts. Standard injection systems deliver carbonaceous material from a vessel to the EAF using air where it is injected through a lance pipe or oxy-fuel burner. Using this method, material delivery to the EAF is limited by the pressure and velocity of the transport air. Loss of efficiency can be observed by looking at the quality of the injection carbon stream during operation or by measuring loss on ignition of EAF slag or off-gas system dust. TSCi™ uses a patented design and proprietary technology to improve delivery of carbonaceous material to the EAF. Using this method, savings at Gerdau Monroe were realized by reducing the amount of carbon used in each heat while maintaining or improving upon existing foamy slag practice. As well, significant savings were achieved as a result of reduced FeO content in the slag and improved recovery of iron. Additional savings can be realized by using a smaller mesh material to take advantage of lower material cost and higher injected surface area. Other inherent benefits to improved injection carbon include lower energy and electrode consumption, reduced refractory wear and reduced maintenance cost.

Oct 30, 2017

By R. J. Hickson

From 1993 through 1999 Cyprus Amax Minerals Company successfully completed eight major construction projects around the world. Six greenfield mines were brought into production, an ongoing operation was completely modernized, and an environmental issue was appropriately remediated. The projects stretched over three continents, from arctic Russia to the Atacama Desert, from 16,000feet to sea level, from city suburbs to remote wilderness, from a low of $130 million to over $1 billion. Open pit and underground; mill and leach; gold, copper, molybdenum, and coal were all encompassed. The breadth of diversity experience from these projects inspired Cyprus Amax to create a “best practices” project management protocol, to steer corporate expansion into the next millenium. This paper summarizes those best practices, while high-lighting project management pitfalls to avoid.

Jan 1, 2000

By David P. Reddick

"Suncor Inc. Oilsands Group mining operation in Northern Alberta, Canada, has been blasting to loosen the oilsands to increase production and decrease maintenance of the bucketwheel excavators for over twenty years. In 1991 an area of the mine was encountered which had a working face of 130 feet rather than the usual 20 to 57. In order to maintain production objectives, the planning and blasting departments of the mine took on the task of blasting as much of the working face as possible. McGinnis Rathole Drilling Company provided the drilling for the project and Mining Services International (MSI) delivered the bulk explosives to the boreholes. It is believed the resultingblasts exceeded several known records in production blasting."

Jan 1, 1992

To George Orwell the year of 1984 was the inspiration for a book. To most New Zealanders it was the year that the fourth Labour Government was elected to power. It was also the year that the review of mining legislation commenced. While Orwell's book and the election of Labour are clearly events of some historic note, one could be excused for classifying the review of minerals legislation somewhat differently in terms of its present achievements! Since the review began it has led a tortuous path through a rapidly evolving policy environment to a point three years hence where no major policies have been determined.

Jan 1, 1987

By D. G. Krige

For the purpose of determining confidence limits for ore grade estimates, an extensive simulated database was used, which included 1728 ore blocks with ?actual? grades and the corresponding estimates based on ordinary and simple kriging. The practical results show that conditional unbiasedness is essential and that acceptable confidence limits can then be set using Normal theory for the simulated error distribution based on the logarithms of the ratios of ?actuals?/estimates with a variance related to the kriging variance. The mean of the data used to prepare the variogram and the estimated block grade are to be used properly in this approach. A practical analysis was also done of the actual point and block data from a very large mined out Carbon Leader area. The distributions of the actual grades for two levels of block sizes with different levels of variability were fitted using three models, ie. two three and compound lognormal. The trends of tonnages, grades and relative profits for a range of pay limits, as well as the usual tonnage-grade curves, show a practical insensitivity for the choice between the three lognormal models considered.

Jan 1, 2004

By Eric Nordhausen

This report and associated deliverables is the culmination of a comprehensive literature survey, data collection and identification of over 500 metal/nonmetal active mines/mills/smelters (over 50,000 tons per year, TPY, production) in the contiguous 48 states. The main purpose was to compile an inventory of the mine/ mill/smelter waste tonnages, thus forming a data base for future research and development in improving waste management and waste disposal techniques in the metal/nonmetal mining industry. The study specifically excluded sand and gravel, sulfur, granite and any commodity that leaves basically no waste when mined and/or milled. The coal waste inventory is the subject of another report. The study provided for locating, mapping. encodating and digitizing all the mine/mill/smelter information made available throughout the nation as well as the climatological, land use, topographical, ecological and vegetative data. Mine/mill/smelter information also included (where possible) acreage and/or volume, mining methods, primary ore and gangue minerals, waste composition and haulage methods and distance hauled. Finally, a discussion is provided concerning present and potential uses of various types of tailings, as well 8S recommending possible R&D in addressing problem areas in waste disposal techniques and management.

Jan 1, 1981

By P. J. Rowsell, M. D. Waller

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. The applications of artificial intelligence systems in the upstream petroleum industry are reviewed. Particular emphasis is placed on current and potential applications in drilling engineering. Several recent advances in drilling technology have led to a large increase in the quality and volume of data available. This combined with the escalating cost, particularly of off-shore operations, is testing the traditional reliance on the skill and judgement of rig operators. AI systems offer enormous scope in enhancing and aiding the performance of these operations

Apr 1, 1994

By F. J. Prokoski

The COALSTAR Project, which operated from November 1981 to December 1982, was a research and development project aimed at providing a reliable and inexpensive means of monitoring various waste site conditions via the GOES satellite system. The GOES system provides data transfer from unattended isolated sites where neither power nor telephone lines exist. The reliability and resolution of the data received while using the satellite link were excellent; however, the site instrumentation gave considerable trouble. The disastrous failure of a large coal waste embankment in 1972 led the Bureau of Mines to undertake a comprehensive program to reduce the likelihood of such an occurence again. Part of this program involved the installation of instruments to monitor the stability of a specially-selected embankment operated by Armco Incorporated near Montcoal, West Virginia. Initially, the instruments were monitored by normal telephone lines and used normal commercial power from the local utility. The project described here was initiated to replace this monitoring system with an unmanned, solar-powered data collection system which transmitted data via satellite to a central computer facility. The satellite data network is the National Earth Satellite Service of the National Oceanic and Atmospheric Administration.

Jan 1, 1984

By M. M. Ayoub

This volume is the second of three volumes comprising the final report of the research project "Biomechanics of Low Coal." It covers only the anthropometric study of low coal miners. Volume I summarizes the overall biomechanical, anthropometry, and work physiology study conducted. Development of work clothes modified to meet the needs of low coal miners is described in Volume III. The male and female anthropometry, with the exception of weight and circumferential dimensions, was quite similar to the comparison populations. The miners tended to be heavier and have greater circumferences. The measurements made in this study were used to develop 5th, 50th and 95th percentile, quarter and half scale, male and female mannequins. These twelve mannequins can be used in work place and equipment design and redesign.

Jan 1, 1982

By J. A. Kost

The objective of Contract J0295041 was to determine if the addition of a surfactant (wetting agent) to the water used for dust control in underground coal mines results in the reduction of airborne dust. Laboratory wettability tests, including the capillary rise test, a coal dust sinking test and zeta potential measurements, were used to select a coal seam/surfactant combination for in-mine testing. Four surfactants were selected for underground testing: Surfynol 465, Aerosol MA-80, DC-13, and Dustallay. The underground tests in the Lower Kittanning seam, Indiana County, PA, involved a Wilcox Mark 20 auger mining system, equipped with spray nozzles located on the cutting augers, Conflow venturi sprays, and a spray manifold. Respirable dust samples were provided by MSA Model G personal samplers and Simslin II instantaneous dust monitor; total airborne dust samples were provided by MSA Model G samplers with UNICO filter cassettes. Based on data obtained from 24 test periods surfactants, as compared to plain water, reduced the airborne respirable dust an average of 27 percent and total airborne dust an average of 36 percent.

Jan 1, 1980

By Michael J. Beus

This Bureau of Mines report describes the development of load cells for measuring compressive loads in timber and lock-bolt support systems commonly used in. coal; metal, and nonmetal mines Design and evaluation is covered in detail to insure a reliable, accurate, and practical instrumentation scheme. The load cells are relatively inexpensive and adaptable to various size support systems. User-oriented procedures are emphasized, and design equations were reduced to a series of nomographs. Laboratory evaluation, destructive testing, environmental testing, and tests to determine the effect of extraneous loads were conducted. Field performance was evaluated in conjunction with ongoing Bureau projects at a metal mine in North Idaho and a coal mine in Utah. Load cells utilizing a titanium alloy as the cell body and weldable strain gages as the strain-sensing components satisfied the basic design and performance criteria, and with minor design modifications, the load cells can be adapted to many mining applications.

Jan 1, 1974

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By A. Azad

SAGD (Steam Assisted Gravity Drainage) is an in-situ oil recovery technique for heavy oil reservoirs. The technique has been successfully applied to many projects in the past 25 years and the process has been, now, well understood. It is now believed that geomechanics plays an important role in SAGD and should be considered in numerical or analytical modeling. Currently, geomechanics is numerically modeled through combining a multi-phase flow and a geomechanical simulator. Numerical modeling is, however, time consuming, need lots of input data, and could not be used for quick decision-making purposes. To decrease the modeling time, this study based on a new version of the Reis drainage model, proposes coupled mathematical model and reserves the effect of geomechanics in the process. Results showed a perfect match with the past experimental and numerical data.

May 1, 2009

By K. Norris

"The Campbell mill has undergone numerous changes over the past 43 years. However the rate of change has increased significantly in the last 4 years. A new grinding circuit, carbon-in- pulp circuit, pressure oxidation plant, and column flotation circuit are all new additions. Other changes have occurred in the last 2 years including a large reduction in sodium cyanide consumption, and the introduction of a computer controlled grinding circuit. More improvements are planned in the next 2 years. Some of these improvements include the construction of an effluent treatment plant, and the replacement of filtering and Merrill-Crowe precipitation with carbon-in-leach and electrowinning.Recent changes and improvements to the Campbell mill are a commitment by Campbell mill personnel and Placer Dome Inc. to decrease operating costs, increase gold recovery and gold production, improve industrial hygiene and safety, and meet environmental compliance with current government legislation.INTRODUCTIONThe Campbell Mine has been and continues to be one of Canada's premier gold mines. Campbell Mine is 100% owned and operated by Placer Dome Incorporated. Milling of ore commenced in 1949 at a rate of 300 tons/day producing 58,000 ounces per year of gold. In 1992 Campbell Mine will mill 1340 tons/day of ore at a grade of 0.6 ounces/ton, producing 275,000 ounces of gold at a cash cost of $205.00 Cdn./ounce.This paper discusses some of the changes that have been made to the Campbell mill in the past 4 years. The flowsheet has undergone extensive changes and will continue to change rapidly in the next 2 to 3 years. A simplified flowsheet of the Campbell mill is shown in figure 1."

Jan 1, 1992

By M. Mead, J. Dumouchel, W. Yule, J. Giroux

The QMM mineral sands of South East Madagascar contain approximately 1,900 million tonnes of mineable sand with a total heavy mineral (THM) content of roughly 4.5wt%. The QMM deposits are the world’s largest known reserves of 60% TiO2 ilmenite and also contain a small volume of zircon. The deposits are semi-continuous and homogenous and the mineralized sands are free flowing with minimal overburden, induration & slimes. These characteristics are favourable to dredge mining and allow the application of conventional wet gravity, electrostatic & magnetic separation to final products. A mature THM mineral suite of high valuable heavy minerals (VHM) content has enabled the development of a relatively simple separation process.

Jan 1, 2005

By E de Villiers

Several methods exist by which the capacity of a dense media separation (DMS) plant can be improved: 1) Increase the feed rate in spite of efficiency 2) Replace with bigger equipment 3) Add whole new module 4) Replace total plant 5) Change over to four shift/ seven days per week roster 6) Replace with alternative process 7) Increase the availability and utilization Options 1 ? 6 have varying degrees of cost implications. The seventh option would seem to be the easiest. Normally it is also the function of the plant operating and maintenance team to maximize this. Usually higher operating and maintenance cost are associated with an increase in these parameters. A general principle that is applicable to plants and systems is that as the complexity increases, the total availability decreases. By simplifying the flow line it may be possible to reduce cost while at the same time increase the availability and utilization. The typical standard DMS flow line contains components that compensate for the variance in pump performance or for the inefficient recovery of ferrosilicon with additional equipment. Things have changed though: 1) Advanced electronic control and monitoring is possible 2) More efficient magnetic separators are available 3) New more user friendly densifiers are available ORIGINAL FLOW LINE In principle the process consists of four flow lines or streams 1) Ore flow ? the feed is divided into a waste and product stream by means of the separating vessel

Jan 1, 2006

By Michel Aubertin

Les haldes à stériles contenant des minéraux sulfureux réactifs constituent un milieu favorable à la production du drainage minier acide (DMA). Au sein de ces haldes, les processus physiques, géochimiques et biologiques qui mènent à la production du DMA sont nombreux et complexes. Un des aspects critiques qui affecte la génération de DMA est la distribution et le mouvement de l?eau dans les roches stériles. La modélisation numérique est un outil qui permet de comprendre, pour éventuellement contrôler, les mouvements de l?eau (et donc réduire la production du DMA) dans les haldes pendant la période d?exploitation de la mine et à sa fermeture. Plusieurs simulations numériques des écoulements non saturés dans des haldes ont été effectuées. Pour ces simulations, on a considéré divers types de matériaux, diverses conditions atmosphériques et diverses configurations géométriques. Les simulations réalisées montrent que l?on peut contrôler les mouvements de l?eau en introduisant des couches de matériaux fins intercalées dans les haldes formées de matériaux grossiers. Des couches horizontales ne sont cependant pas appropriées puisqu?elles peuvent, dans certains cas, favoriser la création de zones humides susceptibles d?amplifier les effets du DMA. Une faible inclinaison des couches de matériaux fins vers l?extérieur permet de palier à ce problème. Les couches inclinées favorisent un drainage des haldes vers la périphérie. Ceci a pour effet de garder sèche une grande partie des stériles et de réduire, par le fait même, la production du DMA.

Nov 1, 2002