Search Documents

By G. W. Jones

One of the major activities of the Bureau of Mines is the promotion of safety in mining and other industries, In this connection, the Bureau determines the explosion hazards' of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. Many dangers are likely to confront men who must enter a building immediately after it has been damaged. Rescue workers must watch constantly for common gases and vapors that may be present in dangerous concentrations in and about demolished, buildings. Fuel gas is the most common source of danger, although refrigerants, gases from furnaces, flues, fires, sewers, and industrial processes, and gas from bomb, explosions in confined places also constitute definite hazards. To rescuers and trapped casualties, these gases offer the hazards of (1) explosion, (2) toxic effects, including asphyxiation and death, and (3) displacement of air so that the oxygen content of the atmosphere is reduced to or below the danger level.

Jan 1, 1944

By F. Dehghani

The influence of different grinding methods on the shape characteristics of magnetite particles was investigated. Also, the effect of particle shape on the flotation of the magnetite, both alone and in the presence of quartz particles, was investigated. The shape characteristics of the magnetite particles were measured and calculated from images obtained by scanning electron microscopy via an image analysis system. The flotation tests were performed using a laboratory flotation cell. Results showed that in the -250+212 µm and -106+75 µm size fractions, ball mill products have a higher elongation value than rod mill products, while in the -150+125 µm size fraction, rod mill products have a higher elongation value. Particles with higher elongation values and lower roundness values have a higher flotation kinetic constant. Furthermore, the influence of magnetite particle shape on flotation is greater, and the flotation kinetic constant is higher, in the presence of quartz particles than in the flotation of magnetite alone Keywords shape, elongation value, flotation kinetics, magnetite.

Dec 1, 2013

By R. M. Cox

The ground forces generated by a properly installed and tensioned mine roof truss assembly can provide permanent mine roof support, even in severe ground conditions, either by direct suspension of the rock loads within the potential failure zone above the mine opening or indirect reinforcement of the natural rock arch that tends to form within the immediate mine roof. Notable advancements in mine roof truss support systems hardware and design technology have occurred since the introduction of the in situ mine roof truss concept for permanent mine roof support in 1966. The systematic installation of mine roof truss support systems has proven to be a very effective method of mine roof control room and pillar mines under a wide variety of ground conditions, even in areas otherwise considered unmineable because of severe roof control problems. Properly designed mine roof truss systems have also been used for permanent support of mine slopes and haulage tunnels.

Jan 1, 2002

By Peter Fischer

Reducing mining costs has become such an important factor in the German coal industry that operators are forced to work only those areas where production costs can be kept low. These areas will normally be located close to the mine shafts because they are easily accessible. Even the shaft pillar is now being considered as part of the winning zone. Before working coal in shaft pillar zones it is essential to assess the impact this will have on the shaft lining. There is a huge difference between sliding and strata-anchored shaft systems. However, if the overburden comprises lightweight soil both types of shaft will have a tendency to protrude from the surrounding ground. This paper presents the geomechanical reasons underlying this reaction and the methods used for predicting and measuring it.

Jan 1, 2007

By H. R. Bullis

"Abstract- This paper discusses what appears to be a flaw in the current belief, widely held within the gold mining industry and investment community, that the creation of ever-larger gold mining companies is desirable for mining companies and investors alike. The basis of the flaw is in the underlying assumption that very large gold producers can discover or acquire new gold deposits of the size necessary to replace extracted reserves on a year-on-year basis over the intermediate to long term (i.e., five to ten years and longer). As it will be noted in this paper, deposits of the size required to replace annual production of very large gold producers (VLGPs) are relatively few in number. Although discoveries of new gold deposits continue to be made, they are predominantly in the 0.5 to 2.0 million ounce range. Data represented here suggest that, although gold production from individual VLGPs continues to increase, the change is due to merging or acquiring other companies or projects with similar reserve life profiles. Therefore, the reserve life profiles of VLGPs have remained flat or have decreased.The paper will note recent changes in the industry and the remarkable increase in gold production reported by individual mining companies over the past several years. It will provide an overview of the geographical and geological distribution of known gold deposits and the range of deposit sizes. Finally, the paper will discuss the challenges that face large gold producers in replenishing their reserves that are being depleted at an ever-increasing rate. Unless otherwise stated, all production and reserve data have been taken from company documents in the public domain or publicly available information."

Jan 1, 2001

By M. Oliverio

The Cigar Lake uranium deposit was discovered in 1981 at the south western end of Waterbury Lake, approximately 660 km north of Saskatoon in the province of Saskatchewan (see Figure 1). It is the largest undeveloped high grade uranium deposit in the world. It contains proven and probable reserves of more than 226 million pounds U3O8 at an average grade of 20.7%. The world average grade is less than 1% U3O8. [ ] The ore body is located about 450 m below surface at the interface between sandstone above and basement rock below (see Figure 2). The sandstone is fractured rock and saturated with water. This makes water inflow a real hazard at the mine. In fact there have already been two significant mine inflow events. The first of these occurred in October 2006 and resulted in the flooding of the mine. The second occurred in August, 2008 during mine recovery activities.

Jan 1, 2011

A shortage of technical skills in all areas of the mining industry is being experienced worldwide. This has significant consequences for design, operations, productivity and safety and, therefore, needs to be seriously addressed, both in the short and longer term. It is therefore both a strategic and a tactical issue. Importantly, however, since mining is a long-term business, the shortage of skills must be dealt with from a strategic point of view to ensure the supply of the necessary skills for future mining. This paper will deal specifically with the provision of high level technical skills, that is, university graduates in mining engineering, and the outlook for the institutions that are currently producing such graduates.

Jan 1, 2009

By J. Antrekowitsch

Keywords: residues, fluorides, chlorides, zinc, steel mill dust The recyclability of various nonferrous metal wastes often suffers from a relatively high fluorine and chlorine content. Both are inserted in most cases by the use of plastic contaminated scrap and a wide variety of different coatings. These halogens lead to poor product qualities and off gas contamination. Especially the history of zinc recovery from steel mill dusts shows, that the today common hydrometallurgical options are on their limit and therefore are not sufficient in most cases. This thermochemical study should give more information about different pyrometallurgical options, that offer both a chlorine and fluorine reduction and efficient zinc recovery, preferably in one process step. Selective evaporation in different atmospheres and conversion with the use of hydrogen are the main parts in this study. The results combined with the relatively small information available from literature should provide a basis for further investigations in this field.

Jan 1, 2005

By Charles Ronkos, Jeffrey Edwards, Brian Brodsky

The Marlin gold-silver deposit is in western Guatemala, 15 kilometers south of a major transform fault that separates the North American and Caribbean plates. A district-scale, northwest-trending graben controlled deposition of a greater than 1200 meter thick upper Tertiary quartz latite to rhyolite volcaniclastic sequence. These volcanics were subsequently intruded and unconformably overlain by a small intermediate, latite to andesite, volcanic complex. Classic low-sulfidation, quartz-calcite-adularia veins and stockwork formed a 2.2 million ounce gold deposit, in association with late-stage andesite dike swarms, along a west-northwest striking normal fault on the eastern flank of the volcanic complex.

Jan 1, 2005

By Gergely Markos

Uranium mill tailings represent a potential threat to the human habitat by containing large amounts of radioactive and chemically toxic substances in high concentrations. These: undesired components enter the human habitat in various pathways such as by erosion and water or air transport. The main objective of this investigation was to evaluate the actual movement and model the potential movement of contaminants by seepage of water from the tailings into the subtailings soil. This report represents various models of the movement of contaminants using both theoretical approaches and empirical evaluation of data available from other investigations. The data consist of field measurements and laboratory determi¬nations of major and trace cations, the dominant anions, pH, and Eh of moist solids, extracts, and waters from the tailings and surroundings. Evaluation and interpre¬tation of data were accomplished by using Eh-pH diagrams, various statistical methods and the WATEQFC computer program. Data analyses show that the critical area of investigating movement- is the interfaces between tailings and the external environment. The chemical differences at interfaces seem to result in a sink system for contaminants. The tailings-soil¬-water system shows extreme complexities because of chemical and physical hetero¬geneity of the system preventing the use of a single comprehensive model to represent real conditions. The validity of the simplifying assumption used has been shown and increasing complexity has been built into the models. Analogs of these models can be used for evaluation of similar systems.

Jan 1, 1981

By F. Bonnet, J. Lehmann, H. Gaye

A review of thermodynamic information and models of slags, including associated software when available, is presented. The pertinence and accuracy of these models is discussed by comparison of their predictions for various slag thermodynamic properties with the available experimental data. Practical industrial applications will be illustrated by a literature review of the dephosphorization process of ferromanganese alloys and by the description of Ti behavior during silico-manganese alloys production. This latter example will show how the thermodynamic models have been used to propose a flotation treatment at low temperature to enhance TiC removal.

Jan 1, 2004

By D C. McPhail, S L. Rogers, J Brugger

Using iron- and sulfur-oxidising bacteria to catalyse the breakdown of sulfides that host the gold is an important biological method for the pretreatment of refractory gold ores. Following this biological treatment a combination of chemical and physical methods are used for leaching (such as the cyanide process) and concentration (such as carbon-in-pulp or electrowinning) of gold. Although these methods are well accepted by industry, they harbour limitations in the processing of low-grade refractory ores, and regulatory agency/public acceptance of cyanide use. Thus, it is beneficial to industry to develop environmentally friendly, cost-efficient leaching and concentration techniques that are based on micro-organisms. This may soon be possible by adapting the results of recent regolith geoscience research, which has shown that micro- organisms are capable of driving a biogeochemical cycle of gold dispersion, transport and reconcentration in the supergene environment. The indigenous microbiota in biologically active soil microcosms from a number of Australian sites are capable of solubilising up to 80 wt per cent of the gold contained in these materials during 50 days of incubation. Studies using molecular microbial techniques have shown that a metallophilic bacterium, Ralstonia metallidurans, is present in biofilms on gold grains from a number of Australian sites. R metallidurans is capable of actively accumulating gold from solution, suggesting that the bacterium may contribute to the formation of secondary gold grains and nuggets. Identifying the biochemical and physiological pathways that lead to the dispersion and accumulation of gold in regolith, and quantifying the reaction kinetics of these processes may thus lead to the development of industrial bio-processing capacities for gold-containing ores.

Jan 1, 2007

By Bruce Hebblewhite

This paper recognises the 25th year of the Morgantown International Ground Control in Mining Conference, by offering a twenty five year review of ground control in the Australian mining industry ? primarily in underground coal. The paper provides an overview of the developments in ground control design methodologies, practices and products. It not only summarises what has been done, but attempts to highlight at least some of the major issues, significant developments, controversies and areas of contention, plus some of the continuing gaps in our understanding or capabilities as we go forward into the next 25 years. Some of the issues included are in relation to: the development of the high strength bolt and cable reinforcement practices widely adopted today and the contrast between stiff and soft systems; a focus on local detail, at the expense of understanding regional stability concerns; dramatic improvements in the use of, and systems available for underground geotechnical instrumentation and monitoring; some of the ground control management trends, including occupational health and safety concerns, availability of suitably trained staff and legislative requirements; the opposing approaches of the empiricists versus the numerical modellers ? is there some middle ground?

Jan 1, 2006

By R. Marrill

Mining is a complex and intensive industry. Extracting raw material with different shapes, sizes, chemistry from the earth?s crust and transform them into a standardized and high quality final product is a big processing challenge - which involves energy and control on large scales. Not only is the physical work challenging, the mining industry today is facing unprecedented challenges: Decline of mineral grade and reserves, cost escalation for new developments and modernization, regulations, safety, lack of skilled people, and market uncertainty are the new constant. It is clear that process control and management of electrical power will be of increasing importance to the recovery rates the mine will achieve. The objective of this paper is to provide a quick vision about future trends and evolutions in technology related to these fields and their impact on Electrical Safety and Control of the mineral recovery. The paper will cover trends in safety, energy management and efficiency, communications of data, control room evolutions, plant integration, other control technologies, and we will examine how these technologies provide information and the benefits of aligned reporting systems to address current industry challenges. More than just the trends or breakthrough concepts, current technologies are available today that can be applied in the mineral recovery operations now to help overcome anticipated future challenges will be presented later in this document. Finally, a brief discussion to look at some real tools to help make real time changes to the process while maximizing recovery and optimizing cost.

Feb 27, 2013

By Wang Shulan

The synthesis process of BaTiO3 from TiO2 and BaCO3 in the molten NaOH-KOH at 350oC was studied by the A.C impedance technique. The A.C. impedance of molten NaOH-KOH (xNaOH = 0.36) and the variation of the conductivity of the salt with time during the synthesized process were measured. The synthesized reaction of the BaTiO3 and the decomposition reaction of BaCO3 are fast and were finished in 10min. The interaction between TiO2, BaO and BaTiO3 and the molten salt was confirmed by the variation of the conductivity.

Jan 1, 2005

By Unknown

More than 60 years ago Lakota (Sioux) Chief Henry Standing Bear asked Korczak Ziolkowski to create a monument of Crazy Horse in the sacred Black Hills. Today, you can see Standing Bear’s dream has grown into enormous reality. Crazy Horse Memorial, mankind’s largest mountain carving in progress, is being carved in the round and when completed will be 641 feet long and 563 feet high. Crazy Horse is only 17 miles from Mount Rushmore National Memorial, giving South Dakota unique boasting rights for having two extraordinary mountain carvings in such close proximity

Jan 1, 2009

By Gary L. Stecklein

This final report delineates the findings of the test programs, simulations, and analyses performed to determine the requirements for the effective application of berms and guardrails as truck restraint systems for elevated mine roadways. Included arts criterion for effective vehicle restraint for guardrail applications and recommendations for berm applications based on scale model tests and computer simulations. Full scale haulage vehicle-berm interaction field tests were performed to correlate the results of these model tests and computer simulations. Recommendations for the construction of berms were made on the basis of tests of berm bearing strength, response of the vehicle to different berms, and predictions based on the obtained correlation

Jan 1, 1981

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, Nevada began large-scale production in 1977. During 2008 Round Mountain Gold Corporation (RMGC) relocated the primary crusher facility approximately 300 meters (1,000 feet) to make room for the next phase of open pit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17 meter (56 feet) high Mechanically Stabilized Embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, Colorado. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design, and construction of the MSE wall.

Jan 1, 2009

The Effects of Collector and Grinding Environment on the Flotation Selectivity of Rosh Pinah Pb/Zn Ore

Sep 13, 2010

By T. R. Paquin

Powerful, easy to manipulate, ventilation modeling software is readily available to most mining engineers. Too often when preparing an initial ventilation model, engineers will go overboard in their design, creating a complex model with hundreds of branches. When, in practice, the creation of a less complicated ?to the point? model, containing a few well-constructed branches, would have delivered the same results. In this paper the author will demonstrate, by using actual feasibility report examples, that when designing a ventilation model, engineers should make more use of the K.I.S.S. (?Keep It Simple, Stupid?) Principle. As mining industry consultants we must continue to improve on, and deliver timely and cost-effective results to our customers.

Jan 1, 2009