Search Documents

By Q. J. Browne, M. A. Miller

Silver Bell produces about 22,000T of fine copper annually from low-grade chalcocite and oxidized copper ore that is recovered by sulfuric acid leaching and SX-EW processing. The current mineable reserves are 146 million short tons averaging 0.39% Cu, at a 0.15% cutoff. Silver Bell utilizes two types of mining methods to develop the low-grade reserves: (1) a conventional blast, load and haul method for run-of-mine leach ore, and (2) rubblization of material on the margins of existing pits. Rubble leach ore is blasted, terraced with a bulldozer, and leached in place. Mining and/or rubble leaching is currently active in four separate pits. Laramide-age intrusive rocks host porphyry copper mineralization at Silver Bell. Quartz monzonite porphyry dikes and stocks, mafic-poor equigranular granite (alaskite), and sub-volcanic dacite porphyry are the predominant host rocks. Most of the ore currently mined comes from near-horizontal enrichment zones containing veinlets and disseminated grains of pyrite and chalcopyrite rimmed by chalcocite. Conversion from a milling operation to a leach only operation allowed for a much lower cutoff grade than was historically used at Silver Bell. Mine geologists were able to increase copper resources by drilling exploration targets that were previously interpreted to provide lower-grade mineralization below cutoff-grade for milling. Geologic parameters that effect the distribution of rubble and mineable leach ore include: ore grade and thickness, variable alteration styles in intrusive host rocks that affect fragmentation during blasting, acid consuming carbonate wallrocks (reactive skarn) which influence leach solution pH, solution flow paths and drainage, presence of leachable oxide mineralization in non-reactive skarn, and depth to hypogene mineralization which is currently uneconomic. Geologic parameters are used to predict rubble bench limits, vary blast hole spacing for consistent fragmentation, and correct errors in mineral zone classification based solely on blast hole assays. An expansion-drilling program has identified approximately 150 million tons of new leachable copper resources with an average grade of 0.35% Cu.

Jan 1, 2002

By J. C. Escobedo, J. M. Almanza, A. Flores, Cortés. D. A.

Secondary aluminum dross, which has been exposed for several years to atmospheric conditions, was characterized using chemical analysis, X-ray diffraction, optical and scanning electronic microscopy, and energy-dispersive spectroscopy. Based on the characterization, a method to purify the solids is presented. This method starts with the washing of the dross in boiling water to eliminate the soluble compounds like Na and K, followed by the physical separation of the metallic aluminum by milling and screening. Finally, an acid lixiviation process is applied using three different acid solutions, HCl, HNO3, and H2SO4. The best results were obtained using HCl. The main insoluble components of the dross after lixiviation were Al, SiO2, and Al2O3. MgAl2O4, AlN, Si, and Na2Al22O3·2H20 species were also found. Based on the alumina content, the solid product could be suitable as a raw material in the manufacture of castable refractories or metal matrix composites.

Jan 1, 2005

By A. Vorster

The objective with mine planning is to consistently deliver production conforming to quality and quantity requirements throughout the life of the mine. The complexity of the operational context of the modern mine extends far beyond the actual production actions and there is a need to find ways of analysing and managing this extended environment. A well-established approach to handling complex situations rely on the creation of representative models that use classification and visualization strategies. An example of the use of a classification scheme is the periodic table of the elements. All physical matter can be expressed as combinations of basic elements. Not only is the periodic table useful in classifying and identifying matter but it can also be used for the prediction of the properties of unknown matter and compositions of elements.

Jan 1, 2001

By R. J. Snoby, M. A. Short, A. Jungmann

In processing coal, the low concentrate value requires high capacity production and sharp classification/separation techniques to reduce specific production costs. The allflux separator meets these criteria with a unique two-stage design. Through a combination of rising current and fluidized bed technologies, the allflux has extended the state of the art by expanding the particle size range that can be efficiently processed. Using concepts that have proven successful in processing concrete sands, small-scale industrial testing with coal feed stocks looks very promising. Attractive applications for the allflux are projected in fine coal recovery from old settling ponds or as a retrofit in existing fines circuits.

Jan 1, 2001

By R. H. Wright

This paper describes the design philosophy and methods employed in constructing the foundation elements for the Little Britain Project in the City of London. The Contract is a design and construct package for the foundations of a 3-storey basement which will be built using "top-down" construction techniques and is to be carried out by Fairclough Piling and Marine on behalf of Wimgrove Nominees. The Project includes 8000 sq.m. of diaphragm wall and barrettes 139 No. large diameter piles ranging from 900mm to 3000mm in diameter and up to 45m deep, and 9 No. cruciform barrettes for the heaviest column loads. Major factors influencing the design of these foundations include differential settlement, heave analysis and a fast track construction approach. Little Britain will provide 43000 sq.m. of space in two linked buildings which will bridge a new road joining London Wall to Newgate Street. The foundation contract is well advanced and the building is due for completion in the Summer of 1990.

Jan 1, 1989

By Felix Cheng

Extensions to the Convention Centre in Adelaide, South Australia consisted in part of construction over the existing railway system comprising nine rail lines and passenger platforms. Vibro-pile (Aust) won the design and construct tender with a solution comprising over 500 cast insitu concrete piles. The pile types were 500 to 900mm diameter non-displacement CFA piles and 400mm diameter displacement V-piles. The V-pile is a cast insitu screw pile developed by Vibropile (Aust) Pty Ltd. Both pile types were installed with minimal noise and vibration required for the project, while the displacement V-pile had the advantage over the CFA pile by developing the same pile capacity but with a smaller diameter and with minimal spoil. The latter was important in alleviating spoil removal problems near the railway tracks and disposal of potentially contaminated spoil. The results of dynamic compression load testing and static lateral load testing indicated that the performance of a 400 mm V-pile was equivalent to a 500 mm CFA for this site. The lateral load testing indicated that the surficial soils have a major influence on the load-deflection response, but despite the site containing up to 4 m of filled ground, the piles were found to carry the required lateral loads satisfactorily.

Jan 1, 2002

By Rodney K. Morrison

MARTA, The Metropolitan Atlanta Rapid Transit Authority, is building a 53 mile heavy rail transit system to serve the City of Atlanta. Phase A of the Rail System, consisting of approximately 14 miles of at-grade, aerial and subway construction is underway. Metropolitan Atlanta lies in the Piedmont Geologic province of Georgia and is underlain by rocks of essentially granitic and gneissic nature. The soils encountered are primarily silty sands which are in-place weathering products of the parent rock and exhibit their relic structure. In general, these materials have presented no unique construction problems other than those created-by proximity of manmade structures, local availability of ground water, and top of rock elevation. The subway sections of primary interest in this paper consist of hardrock and soft ground tunnels and extensive cut-and-cover sections. The cut-and-cover construction includes excavations as deep as 80 feet. Temporary support systems in these deep excavations consist of soldier pile-timber-lagging or soldier pile-tremie concrete (SPTC) walls with internal bracing or tiebacks. In shallow cut-and-cover sections, where right-of-way economics permitted, slopes were laid back partially or fully to reduce or eliminate the need for bracing systems. Dewatering systems were required in most open cut excavations. Due to the close proximity of utilities and existing structures to the MARTA

Jan 1, 1979

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

The stability of surfactant-free foam films was studied using the thin film pressure balance (TFPB) technique. In pure water, it was not possible to produce foam films due to weak film elasticity and strong hydrophobic force. In the presence of NaCl, however, the hydrophobic force was sufficiently dampened to allow metastable films to form. At 10-5 M NaCl, the equilibrium film thickness reached a maximum of approximately 130 nm at pH 6.0-7.3. The thinner films obtained on either side of this pH range was due to the increased ionic strengths associated with the HCl and NaOH additions for pH control.

Jan 1, 2009

By Reza Y. Khaksar

Presented is a rigorous solution for the three-dimensional stability analysis of vertical shafts (excavations) subjected to the self-weight of the soil based on the upper-bound theorem of limit analysis approach. A rigid-block translational collapse mechanism is assumed, with energy dissipation taking place along planar velocity discontinuities. This mechanism is optimized to obtain the critical failure mechanism giving the lowest factor of safety for stability of shafts. Based on comparisons with other solutions, the method is generally found to be accurate in predicting the stability of vertical cuts.

Jan 1, 2006

By Robert H. Bedford

The Rogan-Mallery tin property is in the foothills on the south slope of the Tehachapi Mountains, Kern County, Calif. It was first visited by the senior author in August 1942, and exploration by means of trenching and diamond drilling began in May 1944 and was concluded in August of the same year. Cassiterite, associated with iron-rich gossan, occurs in a limestone roof pendant at places near or at its contact with the underlying granitic rocks. The cassiterite grain sizes range from 20 mesh to 150 mesh. Surface and diamond-drill samples showed tin ranging from traces up to 122.6 pounds per ton. Exploration by the Bureau of Mines included 2,100 cubic yards of trenching and the drilling of 11 diamond drill holes totaling 1,000 feet. Dana Hogan, president of the Rogan Petroleum Co. of Los Angeles, Calif.) brought these projects to the attention of the Bureau of Mines in July 1942, and the following month a Bureau engineer made a preliminary examination in company with Hillard Mallery, of 408 Ruby Street, Redondo Beach, Calif., the man who discovered them.

Jan 1, 1949

By J. A. Finch, T. Weber

"Bubble size in flotation is strongly influenced by frother concentration in the pulp liquor. There is no accepted method of judging the dosage and thus how effectively frother is being distributed to control bubble size is not known. This will hamper certain plant test work where constant bubble size (e.g., when comparing reagents) is implicit. Bubble size is not easy to measure in plant and gas holdup is suggested as a surrogate in the development of a proposed “meter” to estimate frother concentration. The meter is calibrated to enable frother concentration to be estimated on samples drawn from any location in the flotation circuit. The meter and its calibration are described.As general background the action of frothers in reducing bubble size by retarding coalescence is discussed and the bubble generation systems for which the effect will be important are considered.INTRODUCTIONBubble size is an important variable in flotation. The flotation rate constant k has been related to mean bubble size Db by k % Db -n with n ranging up to 2 (Ahmed and Jameson, 1989) and even 3 (Yoon, 1993). Recent work has introduced k % Sb, the bubble surface area flux, given by Sb = 6 Jg / Db (where Jg is the superficial gas velocity or volumetric gas rate per unit cell cross-sectional area), i.e., n = 1 (Gorain et al., 1998). Regardless of the exact value of n, the significance of bubble size in flotation remains. In many plant trials it will be implicit that bubble size has not changed and attention will focus on other process variables. The measurement of bubble size, or a surrogate, would be useful addition to any test work.The size of the bubbles is influenced by several variables, gas rate, gas injection system (e.g., impeller design and rotation speed in a mechanical cell) and pulp composition (chemicals added, percent solids), but the most important is frother concentration (Harris, 1976). The frother functions by retarding coalescence (see appendix), which acts to preserve the small bubbles generated in the pulp (and permits a stable froth to form on top of the pulp). The measurement of bubble size is thus related to measuring frother concentration. The distribution of frother and whether sufficient (to control bubble size) is reaching the intended parts of the circuit then become important considerations. At present there is no simple way to judge frother concentration in a plant. In this communication we introduce a possible methodology, a “frother concentration meter”."

Jan 1, 2003

The French research institute, INERIS, requested the assistance of the CSIR?s Division of Mining Technology in developing further precautionary measures against explosions in their collieries. In response to this approach, an on-board active suppression system was adapted to meet their mining requirements. This system is used on tunnelling machines in Germany where the machine is positioned in the middle of the tunnel, which is therefore not much wider than the machine itself. With this configuration, the machine is never away from the tunnel face during the cutting cycle. As a result, the possible volume in front of the machine of combustible gas requiring suppression is less than 50 m3. In South Africa this technology has been adapted to suit a two-cut mining method which entails greater distances from the face and thus much larger volumes of methane mixtures requiring suppression. The particular configuration of the Explo-Stop® system being investigated required the suppression of possible methane ignition volumes of up to 180 m3of a 9% per volume methane/air mixture. The volume is a consequence of the large cross-sectional area of French underground workings and of the two-cut mining method used in France. In order to take the second cut in the coal seam, the machine is pulled back a maximum distance of 4 m, leaving an air pocket in which gas can accumulate. The machine-mounted system is required to effectively suppress any flame ignited by such a large accumulated volume of methane. The results of the protocol tests done at Kloppersbos showed that the system was capable of suppressing all simulated methane ignitions for the prescribed conditions. This was achieved with a temperature increase of less than a 100°C at the operator?s position and without any flame being detected at this position.

Jan 1, 2001

By S. F. Emmons

Jan 1, 1899

The mining industry continues to be a major driver of the Australian economy generating over A$130 billion in export earnings in 2008/2009. However, the industry has been cited as a significant contributor to green house gas emissions. Australia's proposed carbon trading scheme, the Carbon Pollution Reduction Scheme (CPRS) will financially impact on mining operations; this calls for a holistic planning approach for mining operations taking into account the impact of the emissions trading scheme. Since carbon trading is a new area of study, particularly within Australia, the quantitative effect of the CPRS on the mining industry is uncertain and current mine planning practices do not directly consider emissions. This paper presents results of the study into the impact of the CPRS on a hypothetical large scale open pit operation, using a spreadsheet model based on linear programming and simulation. By varying the production rates, life of mine (LOM), carbon price and ore grades among other variables several scenarios were simulated to determine the impact of emissions trading scheme on the net present value of the project. This study found that the adoption of the proposed Carbon Pollution Reduction Scheme could impact mining operations in Australia by a three per cent to six per cent reduction in net present value, for carbon credit costs of $25/t to $50/t respectively. While the six per cent reduction in net present value for a mining operation is significant, rising fuel prices have had a similar effect in recent years. The most energy-intensive processes are the milling circuit and the flotation concentrator circuit. These processes are jointly responsible for up to 60 per cent of the total emissions, depending on the production rate and the level of offshore processing conducted. Clearly, the introduction of the CPRS makes it is imperative for mining companies to assess the impact of carbon emissions on a mining project during mine planning.

Dec 6, 2010

By E. McCullough, D. Preece, M. Ortel

Geophysical explosive charges are used in mineral resource exploration. They are detonated subsurface and radiate sonic waves into ground monitors, which detect the vibration waves and their interaction with underlying geologic strata. Geophysicists perform computer analyses of the waves reflected from the strata to determine their depth and thickness (Strobel, Berger & Schaefer, 2012). The purpose of this research is to determine how the detonating explosive charge interacts with the adjacent ground and how the induced waves propagate through the surrounding medium. Furthermore, it is necessary to optimize the location of the initiation point within the charge. Establishing both the direction and intensity of the waves will allow geoscientists to refine and optimize geophysical studies that employ explosive charges.

Jan 1, 2013

By José Cayetano

El presente trabajo plantea un proceso para minimizar el contenido de bismuto en las celdas de electrorefinación, a través de la adición de carbonato de bario a la solución electrolito, de forma que el bismuto soluble presente en fase líquida, se precipite sobre la superficie del precipitado insoluble de BaSO4, bajo una coprecipitación por adsorción e intercambio debido al equilibrio dinámico entre el precipitado y la solución de electrolito conteniendo al bismuto. En este sentido, se reduce la presencia del bismuto en el electrolito de cobre en un 75%, adicionalmente se tiene la disminución del contenido de plomo en un 96%, de estaño en 48% y de plata en un 18% aproximadamente.

Oct 21, 2015

By Graham A. Davis

?The ideas of economists and political philosophers, both when they are right and when they are wrong, are more powerful than is commonly understood. Indeed, the world is ruled by little else. Practical men, who believe themselves to be quite exempt from any intellectual influences, are usually the slaves of some defunct economist. Madmen in authority, who hear voices in the air, are distilling their frenzy from some academic scribbler of a few years back. I am sure that the power of vested interests is vastly exaggerated compared with the gradual encroachment of ideas. . . . But, soon or late, it is ideas, not vested interests, which are dangerous for good or evil.? John Maynard Keynes The General Theory (1936) Policy analysts, economists and others have tradition-ally considered mining and mineral wealth a boon, providing rich countries with the resources needed to sustain their modern industrial economies while helping poorer countries generate the foreign exchange, tax revenues and other assets necessary for economic growth and development. Nevertheless, this conventional view has always had its critics.

Jan 1, 2008

By Sneddon N

In November, 1975, Aberdare North colliery was sealed at the surface to extinguish an open fire underground.The fire had developed from a spontaneous heating in one of the open goaf areas of the mine.The mine was re-entered with normal ventilation methods following the isolation of the working district containing the fire. The isolation was accomplished by remotely sealing the open roadways with lly ash emplaced through boreholes from the surface. A subsequent re-entry operation similarly closed the roadways close to the fire and enabled the re-opening of the sealed district.Most of the mine and the underground equipment was recovered after clearing of numerous falls and production recommenced on 25th October, 1976.

Jan 1, 1978

By Pravin Kumar

Goldcorp Inc.?s Red Lake Mine (RLM) is situated in the Red Lake Mining District, a history rich North Western Ontario mining community. Red Lake Mine formerly known as the Dickenson Mine has experienced various degree and type of bursting since the 1960?s. During the 1960?s burst were common in shrinkage stope box hole pillars. After discovering the High Grade Zone (HGZ) between its 30th and 39th levels, the mine has changed its mining method to mechanized cut and fill with cemented paste fill. The rock mass at RLM is mainly massive basalt-ultramafic and behaves in a manner consistent with massive brittle rock. This paper presents the use of empirical and numerical design techniques. The use of the Span versus RMR graph to determine critical stope spans at RLM and the use of numerical design techniques to determine the stability of the sills and post pillars. Selecting of a sill pillar dimension is illustrated using four different failure criteria?s. The four failure criteria are m & s failure criteria, the Pillar Stability Graph, deviatoric stress ???-?3), and induced stress level criteria ?1 /UCS, which are calibrated to RLM?s ground conditions. A wide range of case histories has been studied ranging from stable to highly burst prone ground conditions in order to calibrate the failure criteria to observed conditions and quantified to local micro seismic system.

May 1, 2002