Search Documents

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

As far as is known at the present time, important ore occurrences at Mount Isa are restricted to the Urquhart Shale. These occur at Mount Isa itself, and some 13 miles north along strike at the Northern Leases.The primary silver-lead-zinc and copper orebodies occur as adjacent but discretc entities in lithologieally distinct host rocks. The copper orebodies occur in an envelope of "Silica Dolomite", whereas the silver-lead zinc orebodies occur in shale typical of the Urquhart Shale in general.At both Mount Isa and the Northern Leases, secondary lead orebodies occur at thc surface representing primary stratiform silver-lead-zinc sulphide accumulations in the fresh rocks at depth.Secondary copper orebodies are known only at Mount Isa, where they have formed in favourable environments, but unlike the secondary lead orebodies, not in the positions of the former primary mineralization that gave rise to them. The secondary copper is localized in shale remote from the point where the copper was released into solution by weathering. It was derived from very low grade fracture fillings and disseminations of chalcopyrite in the outcropping or suboutcropping crest of the "Silica Dolomite".Primary silver-lead-zinc orebodies arc oxidized without significant transport or secondary enrichment, but secondary copper orebodies arc characterized by considerable transport and extreme secondary enrichment.The original water table stood at approximately 1,150 ft (mine datum) and for the majority of the mine area controlled the base of complete oxidation fairly closely.An oxidized zone approximately 175 ft deep is general in the Urquhart Shale.Structures affecting ground conditions have influenced oxidation and leaching of the silver-lcad-zinc orebodies, and have had effects vital to the formation of secondary copper orebodies.

Jan 1, 1966

By Keila Gonçalves, Aline Tavares, Danielly Couto

"The sulphide copper deposits from the Carajás area (North region of Brazil) were generated by the percolation of hydrothermal fluids in volcanic and granitic rock and are denominated as IOCG deposits (iron oxide copper-gold deposits). During these hydrothermal events a wide variety of gangue minerals such as amphiboles, biotite and fluorite were formed. These gangue minerals are enriched in fluorine and chlorine which are deleterious elements in the copper concentrate. Chalcopyrite and bornite are the main copper-bearing minerals and they can occur in veins, in brecchia or disseminated in gangue.The study, which included bench scale flotation tests and minipilot plant tests was aimed at improving the fluorine rejection in the flotation process during the flowsheet design for one of these Carajás sulphide copper deposit. All of the study was supported by quantitative mineralogical techniques such as QEMSCAN and the use of a scanning electron microscope (SEM).This paper describes and discusses the results obtained in the metallurgical tests and emphasizes the importance of the quantitative mineralogical characterization during the process conditions optimization and flowsheet design.INTRODUCTIONIron oxide copper-gold (IOCG) deposits encompass a wide spectrum of sulphide-deficient low-Ti magnetite and/or hematite ore bodies of hydrothermal origin and normally have important copper sulphide reserves. In the Carajás mineral province, located at the southeast part of the Amazon Craton in Pará State (Brazil), there is a variety of world-class (>200 million tonnes) Fe-oxide Cu-Au deposits (e.g. Salobo, Cristalino and Sossego), whose genesis has been assigned to hydrothermal fluid percolation in volcanic and granitic rocks. Figure 1 displays the location of the Carajás area.The hydrothermal thermal fluid composition was extremely variable. It may have contained gases, salts (brine) and metals. The metals were carried as various complexes and it is thought to have involved sulphur, chlorine and fluorine containing species. This resulted in some minerals formed during the hydrothermal alteration having high fluorine and chlorine contents. These elements result in smelter penalties in a copper concentrate because they cause the smelter off-gases to be more corrosive."

Jan 1, 2011

By Brad Bulow

Blasting is an essentially violent process aimed to disrupt and loosen rock for productive excavation. Some dilution of any ore present is the inevitable result. This makes blasting a dirty word to most geologists, particularly in narrow vein gold mines. A 1% increase in gold recovery may be worth $1 M extra revenue to a large mine.

Jan 1, 2000

By Joseph J. Feiler

Historical mining operations in Colorado and other western states have resulted in thousands of remnant mine openings. Many are sources of metals loading and acid water generation in surface and ground waters. It is estimated that more than 965 km (600 miles) of streams in Colorado have been impacted by past mining activities. The Animas River watershed in southwestern Colorado is one of the most heavily affected areas in the state. Abandoned mine features pose significant safety hazards to those who enter them. These hazards can include bad air, unstable rock or falls into open shafts, stopes and winzes. Backcountry skiers and snowmobile enthusiasts are particularly vulnerable to falls into snow covered mine openings.

Jan 1, 2006

By Vidyaranya Bandi, Madhav Madhira, Kota Vijay Kiran

"Using hyperbolic relationships for the non-linear responses of shaft and base resistances, a method is proposed for estimating initial shaft and base stiffnesses and ultimate shaft and base resistances of a pile from pile load test results. An iterative procedure is used to arrive at the values of shaft-soil and base stiffnesses and the ultimate shaft and base resistances. The method is applied to load - displacement data available from pile load test results to illustrate its efficacy.INTRODUCTIONA pile foundation is the most effective and economical solution in transferring large vertical loads to deeper depths. As the pile is subjected to axial load, the soil mass surrounding the pile is vital in providing vertical support for the pile. The nature of pile–soil interaction is three dimensional and to complicate the problem further, response of soil is nonlinear. Finding a closed form solution to such problem is extremely difficult. Several methods were developed to study and predict the response of the composite pile–soil system. Faruque and Desai (1982) implemented both numerical and geometric non-linearities in their three dimensional finite element model. Rajashree and Sitharam (2001) developed a nonlinear finite element model of batter piles under lateral loading using a hyperbolic relation for static load condition and modified hyperbolic relation, including degradation and gap for cyclic load condition.The ultimate capacity of the pile is estimated considering the strengths and unit weights of soil layers with depth, overburden pressure and other relevant parameters. The estimated capacities always need to be validated by conducting initial maintained load test. The estimated capacity may differ with the actual at site since the values of strength, stiffness, interface resistance between pile and soil, lateral earth pressure coefficient with depth and soil stratification, etc., differ from the design parameters considered for estimating the ultimate capacity of pile. The estimation of axial capacity of piles involves considerable uncertainties in selection of appropriate design parameters and the design rules are not always consistent with the installation procedures/processes involved."

Jan 1, 2017

By Tom Olsen, Tom Ohrling, Peter Taggart, Chris Martin

"North American Palladium commissioned the new concentrator at the Lac des Iles mine in the summer of 2001. The 15,000 tonnes per day mill replaced the existing 2,400 tonnes per day facility, as part of a major mine expansion.At Lac des Iles, the grain size distribution of the platinum group minerals (PGM) is bi-modal. Roughly two-thirds of the PGM are relatively coarse-grained, and often associated with fast floating copper and nickel sulphides. The remainder is ultra-fine, and locked in silicates, which poses a special challenge to the metallurgist. The previous mill typically recovered just the fast-floating mineralisation, but to achieve target recoveries, the new mill has to recover a substantial amount of the ultra-fine PGM. The metallurgical challenges associated with the recovery of fine-grained PGM in the talcous Lac des Iles ores, are described.The paper describes the approach used in circuit optimisation, and how metallurgical and operational optimisation raised palladium recoveries by more than 6% in six months, by tuning the circuit to recover some of the ultra-fine PGM mineralisation.BACKGROUNDThe Lac des Iles mine, owned and operated by North American Palladium Limited, is located about 115 kilometres north of Thunder Bay, Ontario. The mine originally opened in December 1993, and prior to 2001 included a mill capable of handling 2,400 tonnes per day of ore delivered from the nearby Roby pit.Following an intensive exploration programme conducted in 1999, and a detailed feasibility study, conducted in 2000, North American Palladium initiated a mine expansion project, the objective being to expand milling throughput from 2,400 tonnes per day to 15,000 tonnes per day. This required construction of an entirely new mill, which was commissioned in May 2001."

Jan 1, 2003

By Randy Clarkson

"Free gold particles occur in many base metal and precious metal mines throughout the world. Occasionally mine operators are unaware of the presence of free gold particles in their ores because they have not seen free gold hand specimens or at the working face of the mine.Due to the high density and malleability of gold, large circulating loads of free gold particles can build up over time in grinding circuits. This gold is often deposited in unintended traps throughout the mineral processing system.These unidentified free gold deposits represent a serious security risk as well as inaccessible inventory of gold. Deposits of free gold particles often remain undetected by mine management until they are accidentally discovered while repairing mill equipment. The trapping and subsequent release of gold particles can frustrate attempts to calculate accurate metallurgical balances.Nuclear tracers have been used to determine the free gold recovery efficiency of gravity recovery equipment, drills, and sampling equipment (Clarkson, 1994, 1997, 1998, 1999 and Walsh, 1986, 1992). In 1995, the author used radiotracers to locate and eliminate gold traps at La Mine Doyon (Clarkson, 1997). In 1998 and 2001, the author also salted mineral processing circuits at Royal Oak's Pamour Mine in Timmins (Clarkson, 1999) and at Gold Corp’s Red Lake Mine in Ontario with radioactive gold particles.The gamma and X-ray radiation from gold's nuclear isotope (Au198) were detected through steel, in pipes, and in moving equipment with scintillometers. The radiotracers proved to be a safe, rapid and accurate method of identifying gold traps, improving security, determining the recovery efficiency of Knelson gold concentrators and estimating retention times of gold particles in various processes."

Jan 1, 2003

By S Kundu, J Zanganeh, D Eschebach, B Moghtaderi

The concentrations of methane and coal dust vary from one location to another in underground coalmines. In the presence of an ignition source, such as static electricity, these mixtures can initiate explosions and consequently cause massive destruction. Research data can help in understanding the level of hazards and associated risk these flammable mixtures can produce. For instance, the level of peak explosion pressure and flame speed can be well understood from experimental and numerical research data. With this aim, methane–air mixtures and methane-coal dust-air mixtures were employed in a ducted spherical vessel. According to literature, the maximum value of peak explosion pressure can be obtained in vessels of spherical geometry when compared to vessels of other geometries. Thus the values of explosion parameters generated from spherical vessels can be incorporated in understanding the highest level of hazard that can occur in a real world scenario.In this study, the duct integrated with the vessel resembles any channel or pathway connected to a methane and/or coal dust rich area in the mine. Experimental investigations emphasise that the severity of explosion in the explosion zone transmits to the channel or pathway. The length of the channel or pathway also plays an important role on the values of explosion parameters. The greater the length of the channel or pathway, the higher the explosion pressure is and therefore the higher the destruction. Ignition energy and concentrations of methane and coal dust were varied in collecting experimental data. The data of explosion parameters thus obtained can be employed in addressing hazard mitigation strategies in coalmines.CITATION:Kundu, S, Zanganeh, J, Eschebach, D and Moghtaderi, B, 2017. Incorporating research data in addressing methane and coal dust fire, and explosion hazards in coalmines, in Proceedings Australian Mine Vent Conference 2017, pp 175–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By W. J. Birch, A. Wetherelt

The scaled-distance model for blast vibration analysis is the standard method employed throughout the surface mining and quarrying industries to model Peak Particle Velocity (PPV) data. Although empirical, the method is widely accepted and through the simplicity of its application and ease of graphical verification is set to remain a popular option. The validity of the technique relies principally on the fundamental parametric assumption that blasting data is normally distributed. Throughout the evolution of scaled-distance modelling, this is an issue that has most often been presumed rather than proven (most likely due to the tediousness of the calculations involved). In the few cases when normality has been given some degree of consideration, the result has been the product of a simple visual inspection of frequency distributions: clearly unsatisfactory. However recently the soundness of this assumption has been brought into question, with obvious connotations for blast modelling in general. This paper considers this fundamental issue and seeks to investigate the normality hypothesis within the blasting context through an in-depth statistical analysis of what possibly can be described as an ‘ideal’ blasting dataset. This being a rare case study concerning an opencast coal site in England, where for the entire life of the site every single blast was monitored and recorded through the use of permanent monitoring stations. This has provided a unique ‘total population’ dataset of considerable size from which the assumptions of normality are put to the test.

Jan 1, 2005

By Stephen H. E. Phillips

This report outlines the modifications that have been carried out to the original prototype rectangular shaft sinking equipment for its use in a circular shaft. The surface testing of the machine is described where seven, 24 ft. diameter shafts were excavated to an average depth of 21 ft. at rates ranging between 1 ft/hr and 1.9 ft/hr depending upon the prevailing conditions. The durability and productivity standards for the equipment were established indicating that the objectives of the project had been realized. That is, when using the machine the sinking rates could be increased by 25% and costs reduced by a corresponding amount compared with conventional drill and blast methods. In addition it was shown that the machine had been developed to a state of fitness for sustained underground use.

Jan 1, 1981

By G K. Jorkenson

Blast designs to cast a percentage of overlying waste rock off coal seams differ greatly from conventional blast designs for surface coal mines. Today, blasting engineers can benefit from computer simulations to test various blast designs and reduce cost and time spent on the old trial-and-error method.

Jan 1, 1989

By Kot Unrug

Mine seals are necessary in nearly every mine to isolate mined-out areas from the ventilation network. There is a large number of seals in active mines and that number continually increases as the development spreads across the reserves. The recent accident caused by the failure of seals in the Sago mine resulted in new regulations. These regulations have been set based on a principle of eliminating the risk of failure, rather than the sound engineering and understanding of the conditions that may cause seal failure during an explosion of methane in sealed areas of the mine including the probability of such occurrences. This paper discusses the following subjects related to mine seals: The potential causes of methane explosions and the dynamic effects of pressure wave propagation. Seal materials and methods of construction in view of the interaction of the seal with the host rock environment as well as requirements for gathering geotechnical data. The design of seal dimensions is based on loading conditions, therefore the probable ranges of such loading is reviewed. There is also discussion of possible methods for shielding of seals from pressure pulses following an explosion. Particular seal?s types are examined in reference to the conditions at the seals location. A novel design is presented that will be a low- cost solution for the sealing of mined out areas. Recommendations are given for further research leading to a rational engineering system for design of new seals in coal mines.

Jan 1, 2008

By Blott S. F

The smelting plant and equipment at Mount Isa, as originally designed and built, was described by J. M. Callow (1) *.F. A. Forward (2) described alterations and additions to the plant and discussed the metallurgy of mixed carbonate-sulphide concentrates at Mount Isa, prior to 1933, in the Proceedings of this Institute.In 1933, A. F. McAskill (3) gave full mechanical details of the plant in a paper presented to the Institution of Engineers, Aust.FLOW SHEETSFig. No. 1 represents the present general flow sheet. Forward's (2) flow sheet is reproduced here as Fig. lA, and will serve for comparison in depicting subsequent deletions from, and alterations and additions to, the plant.Fig. No. 2 presents the daily tonnage flow sheet of 1939 practice.ALTERATIONS SINCE 1933General. Many changes in metallurgy and operation have taken place, particularly subsequent to March, 1935, when the treatment of a mixture of carbonate and sulphide ores was discontinued and the mill commenced operating on all-sulphide ore. This alteration brought about the elimination of gravity concentration-Jigs and Tables and resulted in the production of all-floatation concentrates of a very fine sizing. Refer Table No. 2, page?) Radical changes in the analyses and physical nature of concentrates also followed (see Table Nos. 1 & 2, page ?) and, similarly, radical changes in the smelting plant have been slowly brought about.

Jan 1, 1939

By I. Bock

Selective Blast Mining (SBM) makes use of milli-second sequential blasting technology to separate the valuable reef material from waste rock in the blasting operation at stope faces in the mining of tabular ore bodies such as exist in the gold and platinum mines in South Africa. The waste rock is cast blast to the back of the stoping area, and the reef material is fractured and deposited close to the stope face. Only the reef material is transported to the surface. A simplified economic model is presented to evaluate the economic benefits of SBM. Although premature, in that adequate experimental demonstration of the validity of the model has not yet been possible, the model is presented since it indicates substantial benefits in the case of narrow reef gold mines. It is suggested that many marginal mines should seriously consider SBM. Benefits can also be realised in platinum mines, but a lot more experimental work is necessary to establish cost parameters more reliably. Some practical experience in the use of SBM in the mining of the UG2 reef is presented.

Jan 1, 1998

By M. Salas, L. Rolf, H. Z. Kuyumcu

"Industrial use of abrasive stress takes place in the area of fine grinding and in order to clean surface contaminated soil particles. Also, at many mechanical operations abrasion emerge as an unintended side effect. At the Institute for Raw and Waste Material Processing at the Technical University of Berlin systematic investigations are carried out, to further the knowledge regarding the dependence of abrasion process on material properties and stress mechanisms as a basis for design and optimisation of the process or for its avoidance. Aim was the mathematical description of the abrasion process running with a single particle stress. For the purpose of investigations an agitation cell was used. Limestone served as material.In the presented work the influence of particle diameter, particle shape and collision energy on the mass and particle size distribution of abrasion debris was studied. The surface geometry of the particle was characterised by the particle shape factor ?x and the particle diameter dp. The particle shape factor ?x stays in direct relation with the abrasion degree x, and can be substituted by a mathematical function of x.Physically the particle shape factor ?x can be interpreted as a proportion of abrasive stresses splitting up complete crystals and crystal fragments. These two different mechanisms depend on different ratios of curvature of the surface of the stressed particle. The abrasive stress of strongly curved surface areas leads to separation of complete crystals. The abrasive stress of weakly curved surface areas leads to separation of crystals fragments. Accordingly the mass of wear mAb and median diameter of the abrasion debris d50 are different. The derived mathematical relations consider this behaviour by the particle shape factor ?x , which represents the ratio of the mixture of both stress mechanisms. The dependence of the particle shape factor ?x on the abrasion degree x with an exponent approximately to 2/3 points out that the particle shape factor ?x represents a surface area relation."

Jan 1, 2003

In a gravity separation device, particle shape, size and density all play a role. The combination of these determines where each individual particle reports to in the viscous fluid, where particle crowding (solids to water ratio) also plays a role. To understand the performance of gravity separation devices in the heavy mineral industry, these particle characteristics need to be measured. There are various challenges in analysing particle density and particle size simultaneously for the purpose of quantifying gravity separator performance, not to mention particle shape. These analytical challenges include the high cost of high-density sink-float fractionation, toxicity of high-density sink-float media, inability of sink-float media to fractionate at densities greater than 4.0 g/cm3, and the time-intensive nature of these fractionations. The use of the detailed particle-by-particle output from Qemscan® particle mineral analyses (PMA) as a fast and cost-effective alternative is evaluated. The size and density outputs from the Qemscan® were employed to characterize the performance of a heavy mineral spiral concentrator as an example. Critical analytical requirements are to be addressed before the Qemscan® output data can be utilized. Keywords Gravity separator, performance, heavy minerals, Qemscan® particle mineral analysis

Jan 1, 2011

By A R. Penney

Since mining-induced seismicity first became apparent at the Beaconsfield Gold Mine in 2002, there has been an ongoing program of geotechnical investigations to understand the phenomenon and allow for the development of strategies to manage the risks it posed to personnel, the business and the community at large. Studies resulting from a seismically induced rockfall on Anzac Day 2006 have been extensive, and have advanced the understanding and management of seismicity at the mine. Enhancement of the mineÆs seismic array, implementation of extensive monitoring of ground behaviour, improved ground support and reinforcement design, and ongoing numerical modelling provide a technical framework for the management of seismicity. In addition, extensive involvement of the workforce in risk assessment and the development of standard work procedures (SWPs), has contributed to a æbest practiceÆ approach to manage seismic hazards at the mine.

Jan 1, 2008

By Henry M. Harris

The roll forming of oxide powders was studied in a Bureau of Mines investigation to find the conditions and parameters required to make satisfactory ceramic strip. High-quality porous or dense alumina, zirconia, and porcelain shapes were made by sintering strip roll-formed at room temperature from powders containing minor amounts of binder and water. Strips with thicknesses of 0.04 to 0.08 inch and bulk densities from 40 to 90 percent of theoretical densities were made. The parameters most important to formability were particle size, condition of the powders, and roll gap. Other factors affecting quality were speed and surface condition of the rolls, amount and type of binder, water content, and sintering conditions. Ceramic strip was formed at rates up to 78 feet/minute, which is 13 to 23 times faster than reported by previous investigators, and forming was done in a simple and inexpensive roll unit. Reshaping the strip was possible by cutting, grinding, shearing, and stamping. The following innovations were developed that allow roll processing not normally possible with ceramic powders: (1) Fine-sized powders were made into strip by preparing these as partially sintered granules; (2) thick strip was formed by pressure feeding powders into the rolls; (3) flexible strip was made using a rubber-base bonding agent; (4) corrugated strip was formed on shaped rolls; and (5) porcelain strip was densified and reduced in thickness by rerolling while hot.

Jan 1, 1970

By J. R. Goode

"The Las Cristinas deposit contains about 10.2 million ounces of gold at a grade of 1.3 g/t. The deposit comprises a layer of fully oxidized saprolite (SAPO), a layer of sulphide-enriched saprolite (SAPS), carbonate leached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same level in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper it having been leached and deposited in the SAPS zone.A previous owner started investigation of the Las Cristinas deposit in Venezuela in 1991. Over the next seven years, 1174 holes with a total length of 159 km were drilled, extensive metallurgical testwork, including pilot plant operations, were conducted and feasibility studies were completed. Construction was started in 1997 and again in 1999 but was suspended.Crystallex has been producing gold in Venezuela since the early 1990’s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana, (CVG), to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in early 2003 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and Professor A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-in-leach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the recent testwork, discusses the proposed plant design, and presents economic data."

Jan 1, 2004