Search Documents

By K. G. Tshilombo

It should be possible to use an oxygen probe to follow iron removal during converting, if local equilibrium is established between iron in the matte and the iron oxides in the fayalitic slag. The oxygen activity is expected to increase strongly as the iron content of the matte decreases (and the iron activity in the matte drops) while the iron oxide activity in the slag remains constant. To test this idea, oxygen activities were measured in synthetic mattes (made up of mixtures of Cu2S, FeS and Ni3S2) when in contact with silica saturated SiO2-FeO slags, and silica and (initially) magnetite saturated SiO2-FeO-Fe3O4slags. The measurements were performed on laboratory scale at 1250°C, using an oxygen probe consisting of an MgO-stabilized zirconia electrolyte and Fe/FeO reference, and containing the sample in a silica crucible. Electrical contact to the matte was by means of a platinum wire. The measured oxygen activity was sensitive to the iron content of the matte, and insensitive to the composition of the gas atmosphere over the melt. The measured oxygen activity was generally close to that predicted by Fact Sage calculations. This indicates that such oxygen activity measurements could be useful to monitor iron removal during converting of nickel-copper-iron mattes.

Jan 1, 2007

A drive, 3,500 ft long, was planned to explore mineralization exposed by diamond drilling. A rate of advance of 150 ft per fortnight, approximately double previous Broken Hill rates, was required. Subsequent to the completion of this drive its extension for a further 6,200 ft was planned to provide a main haulage way along which ore could be transported from a newly acquired lease back to the main hoisting shaft, a total distance of 13,500 ft.This paper describes the working conditions, relationships, manning and costs, and gives details of the cycle and equipment used to achieve rates up to 170 ft per fortnight.OBJECTIVEDiamond drilling from the 1,000 ft level at the Delprat Shaft section had indicated that the zone of mineralization, about 150 ft wide, which had been explored on the 1,000 ft level for a length of 2,600 ft, continued downwards with a westerly dip. The drilling results showed that within this wide zone there were arrower lenses of mineralization of possibly payable grade (see composite plan, Fig. 1).Diamond drill holes of 2,000 ft and over, particularly through heavily sheared areas of sericite schist, had been found to be costly, slow, and inadequate in testing the potential and trends of these smaller concentrations of mineralization.It was therefore decided that an exploratory drive should be advanced from the northern limit of the 1,480 ft level into the western mineralization, and that from this drive diamond drill holes should be drilled at dose intervals to outline the ore.The 1,480 ft level was chosen for the following reasons.1. It had the greatest northerly reach of the accessible levels at No. 7 Shaft section below the 1,000 ft horizon and therefore would enable the test to be made most quickly.

Jan 1, 1965

By Turker L

The leaching of Tellness (Norway) ilmenite concentrate in hydrochloric acid and mixed aqueous HCl-alcohol solutions at boiling temperatures was investigated. It was found that the alcohols methanol, ethanol and ethylene glycol all substantially increased the leach rate and in the case of methanol and ethanol this was achieved at lower boiling temperatures compared with aqueous HC.

Jan 1, 1986

Common practice in mineral resource estimation consists of partitioning the orebody into several domains defined by grade intervals, prior to the geostatistical modelling and estimation/simulation at unsampled locations. This paper shows the pitfalls of grade domaining through a case study in which we compare the performance of several estimation schemes and demonstrate that the use of domains defined by grade cut-offs implies a deterioration of the resource estimates, mainly in what refers to precision and conditional bias. Then, several conceptual limitations of the grade domaining approach are stressed, in particular the fact that it does not account for the spatial dependency between adjacent domains and for the uncertainty in the domain boundaries. Also, this approach is shown to be sensitive to the cut-offs that define the domains, to provoke artifacts in the kriging maps, histograms and scatter grams between true and estimated grades, and to lower the kriging variance, a feature that may impact the mineral resource classification. An alternative approach is finally proposed to overcome these limitations, based on a stochastic modelling of the grade domains and a co-kriging of the grades using information from all the domains. Keywords: geostatistics, kriging, conditional bias, geological control, grade zoning.

Jan 1, 2005

Demonstrate the technical feasibility of using nontraditional, low-rank, coal-based fuels and new coal-based technologies for mineral and metallurgical applications. Approach A cooperative research effort was initiated between the Bureau of Mines, U.S. Department of Energy and the minerals industry to extend the application of the fixed-bed gasification process to low-rank Western coals. The research effort enabled cooperators to gain operating experience in the use of hot, raw producer gas for iron ore pellet induration and other high-temperature mineral processes. Researchers were able to gather data regarding the fundamental engineering aspects of the fixed-bed process and gas cleanup for a wide range of solid fuel properties. Applying Fixed-Bed Gasification As a prerequisite to gathering the data needed for the study, the Bureau of Mines designed and installed, at one of its laboratories, a 6.5-ft-diam. single stage, fixed-bed, air-blown atmospheric pressure gasifier. The gasifier was coupled with a hot, raw gas combustion system and iron ore pellet in. duration kiln. The gasifier is rated at 1.5 ton/h capacity of bituminous coal.

Jan 1, 1987

By E. Farrokh

Estimation of the cutter life and cost is a part of evaluating performance for a hard rock TBM in any project. Various approaches has been proposed for calculation of disc cutter life in various rock types based on machine specifications and rock strength and abrasivity. Cutter change time is a parameter that is used in some of the estimates and is defined as the average time required for changing a cutter on the cutter head and cutter life is the number of cubic meters of excavated rock per each disc cutter. Analysis of cutter life information of several tunnel projects from around the world has revealed that the published models for estimation of cutter consumption require some revisions to offer a more accurate prediction. The preliminary analysis of data shows that the average cutter change time is approximately 66 minutes for different cutter sizes and there is a minimal difference between corresponding cutter change times of the large (e.g. 19 or 20 in) versus smaller cutters (e.g. 15.5 to 17 in). This paper reviews the available and published cutter life data from various projects. It also introduces new models for estimation of cutter life and cutter change time as part of TBM down time and utilization analysis.

Feb 27, 2013

By F. Kavicka

An original application of ANSYS simulated the forming of the temperature field of a massive casting from ductile cast-iron during the application various methods of its cooling using chills. The numerical model managed to optimize more than one method of cooling but, in addition to that, provided serious results for the successive model of structural and chemical heterogeneity, and so it also contributes to influencing the pouring structure. The file containing the acquired results from both models brings new and, simultaneously, remarkable findings of causal relationships between the structural and chemical heterogeneity and the local solidification time in any point of the casting. The determined relations therefore enable the prediction of the face density of the spheroids of graphite in dependence on the local solidification time. The calculated temperature field of 500x500x1000 mm casting of ductile cast-iron with various methods of cooling has successfully been compared with temperatures obtained experimentally. Acknowledgments. This analysis was conducted using a program devised within the framework of the GA CR projects (No.106/04/1334, No. 106/04/1006 and No. 106/04/094), of the COSTAPOMAT-OC526.10, MPO/FI-IM/021, EUREKA No.2716 COOP and KONTAKT 14/ 2005/06.

Jan 1, 2006

By S. Parada, P. T. Jones, M. Guo, S. Smets

The corrosion behaviour of a high-quality rebonded magnesia-chromite refractory in contact with a vacuum oxygen decarburization (VOD) slag with high Al2O3content (15?20 mass per cent) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterization of corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature and the Al2O3content in the slag is discussed. Keywords: corrosion, magnesia-chromite refractory, VOD slags, vacuum induction furnace

Jan 1, 2004

By A. George Stern

In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should 'rave the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.

Jan 1, 1940

By Paul J. O'brien, George N. Neary

"The base metal mine at Buchans, Newfoundland, has been producing since 1928. For many years, mill tailings were disposed of by dumping into a nearby natural watercourse via which they were transported to Red Indian Lake and deposited. In 1965, environmental concerns prompted the establishment of settling ponds near the mine site. Effluents fed to these ponds included slimes washed from mine backfill sand and waste water pumped from underground as well as mill tailings. Dusting around the perimeter of the ponds was first observed around 1970and within a couple ofyears reached serious proportions. A program to alleviate the condition by developing a vegetative cover over the tailings was commenced in 1974. The work was successfully carried out and demonstrated that the large area of waste could sustain a permanent cover of grasses.This paper outlines the experimental work done at Buchans as well as the procedures followed and the problems encountered in carrying out full-scale revegetation."

Jan 1, 1981

By J M. F Clout, E Donskoi

The ability to design a beneficiation process for a new orebody based on particular feed characteristics is a powerful and practical tool. A new technique has been developed where beneficiation outcomes can be calculated by combining feed size-by-size chemical analysis, mineralogy, liberation and particle characteristics with a series of simple theoretical unit separation models rather than a simple mass balance approach or an exhaustive beneficiation test program. The new technique provides the ability to rapidly identify ore types that have the potential to meet product specifications whilst also rejecting others that will not meet specification even if a perfect separation was achieved. Beyond the broad scale decision making process, practical mineral separation curves from actual plant data can be used to more closely simulate the proposed process. This approach reduces the amount of laboratory and pilot plant work necessary by targeting what process stages will be required, increases early rejection of uneconomic options, identifies problematic ore types or unit operations and is a step towards estimation of final grade and recoveries achievable in potential circuit configurations.

Jan 1, 2004

By C. Sawmliana

Deep-hole blasting operations in opencast mines are always associated with some annoyance to the surrounding areas in terms of ground vibration, noise, flyrock, etc. These become more severe when underground mines run parallel to them. Blasting in opencast mines may pose danger to the underground mines in terms of roof/side failures, damage of water dams, isolation/ventilation stoppings and other underground installations. The paper discusses a case study in India on the impact of deep-hole blasting in Ramagundam Opencast Project ? III on the stability of various water dams of GDK-6B Incline coal mine operating in close proximity. The stability of underground water dams of GDK-6B Incline mine was endangered due to deep-hole blasting at OCP-III. There were 15 water dams in seam 3 and 16 dams in seam 4 of the underground mine. The physical strength tests using a Schmidt Hammer instrument were carried out in all the 15 water dams of No. 3 seam and 16 water dams of No. 4 seam. The test revealed that there is a decrease in compressive strength values of three dams of seam 3, namely 6A, 6B and 7. Theose three dams were also directly connected to the water source. Water seepage was also observed from the surfaces of the three dams. However, they were found to be stable in accordance with their design parameters and damage point of view while considering a threshold value of ground vibration as 25 mm/s. It was found that the value of tensile stress generated by a vibration of 25 mm/s was much lower (i.e. 0.171N/mm2) than the tensile strength of the two weakest concrete dams (1.85 N/mm2). Ten experimental blasts were conducted at different working benches of the opencast mine and the ground vibration data were recorded in roof and pillars near various underground water dams. The maximum value of vibration data recorded was 5.9 mm/s in roof near dam no. 1 in seam 3 with the dominant peak frequency of 22 Hz. No adverse effect on either of the dams was observed after that blast. During the period of study, no deterioration/adverse impact was found in any dam of the mine. Based on the results of the study and the analyses of the data, optimized blast design parameters and explosives weight per delay were suggested for the opencast mine to maintain the safety of the underground water dams. Keywords: Opencast blasting, damage, water dams, underground mine, ground vibration

Jan 1, 2009

By F. Habashi

The first documentary evidence for the use of fire to extract a metal was furnished by the wall paintings of the ancient Egyptians showing workers using the blowpipe and bellows to increase the temperature to melt gold in a crucible. Furnaces grew in size and complexity, coke replaced charcoal in the blast furnace, and the Industrial Revolution took place in England that gradually spread worldwide. More metals became known and new techniques were introduced for their extraction. Among these, metallothermic reactions became prominent in the nineteenth century immediately after the discovery of the electric current and its use to liberate the alkali metals from their salts. Once these metals became available, they were used to produce aluminium from alumina that resisted all other methods of attack. Aluminium, now available on a large scale, was used to decompose the most stable compounds and liberate more metals that became the basis of modern civilization.

Jan 1, 2004

By C. J. Badenhorst

The scope of this project was to research, develop and eventually produce a personal occupational hygiene and safety exposure monitor system to assist in recording and analysing various stress factors that could affect the health, wellness and safety of employees, i.e. that could result in injury or ill health of workers, create stress build-up within individual workers that could negatively affect worker alertness and safety, and, may even result in permanent disability or death. Utilized systems at the time were all reactive, whereas the DOHEMS (Proactive Digital Occupational Hygiene and Safety Exposure Monitoring) System enabled the measurement of exposure (and associated risk) in a proactive manner via real-time exposure and digitized recordings. The idea of the development was to create a unit that is so cost effective, small and light that every worker can use a system on a daily basis. The development will eventually replace current, bulky and expensive monitoring equipment. The device must be a portable battery operated device and monitor the immediate working environment by periodic sampling for vibration, noise, toxic gasses (NO/NOX/CO/VOC, etc.), body temperature and heart rate. The samples must be time and date stamped, utilizing a real-time clock (RTC) synchronized with the closest regional secondary time source and related to synchronized real-time video captured samples. These samples are then recorded onto a rugged non volatile storage device with the capacity to store a vast number of samples covering the entire working shift of eight (8) hours plus. The system has been fitted with a clear visual local alarm indication system, indicating any excessive exposures or stresses, for the worker?s supervisor to respond to. This system allows for a pro-active approach. The system is also a wireless system (to the external environment) so as to not affect the mobility of an employee and flameproof to allow for use in explosive environments. Keywords: safety, digital, exposure, monitoring, proactive.

Jan 1, 2010

Removal of Arsenic in Fluorite Ore by Simultaneous Grinding-Leaching with NaHS Generally speaking, a high-grade fluorite ore is converted into hydrogen fluoride (HF), which is essential for the semiconductor manufacturing. With the continuous depletion of resources, novel technologies for processing low-grade fluorite ores are urgently needed, in order to lower the arsenic concentration to less than 100 mg/kg. In this study, a low-grade fluorite ore was upgraded by removing arsenic, which is difficult to remove by conventional method. The mechano-chemical leaching of fluorite ore (i.e. the sample was ground in presence of NaHS, using a beads mill) was carried out to investigate the removal of arsenic from the low-grade fluorite. Experimental results showed that the arsenic concentration was reduced to 73.2 mg/kg.

Sep 13, 2010

How to Evaluate Crushed Rocks for Concrete Production

Sep 13, 2010

By Parker A. J, Giles D. E

Solutions of copper(II) sulphate in acidified aqueous acetonitrile leach copper from copper-lead matte derived from the drossing of lead with sulphur to produce solutions of copper(I) sulphate. The reactivity of the matte constituents towards copper(II) sulphate is Cu2S> PbS > CuS > > Pb. According to the leach conditions, part or ,all of the copper may be leached 'leaving a residue of CuS/PbS, or S/CuS/PbS04, or S/PbS04, to be recycled to the lead smelter. Complete extraction of the copper requires leaching with oxygen which occurs under mild conditions in the presence of acetonitrile and sulphuric acid in water. Copper is selectively recovered as a pure product by electrochemical or thermal disproportionation of copper(I) sulphate solutions. A notional process is proposed.

Jan 1, 1979

By B. Haugrud, E. McConaghy, M. Collins, G. Smith

"Laterite ore processed by the Ambatovy Joint Venture in Madagascar is primarily limonitic in nature, containing about 40 to 45 wt.% Fe and 1.1 wt.% Ni. The process selected for treatment of this ore considered the behavior and deportment of iron in each step of the commercial flowsheet. Such considerations included nickel and cobalt recoveries, reagent consumptions, liquid-solid separation characteristics, and both intermediate and final product purities. In this paper, the results for the first three years of commercial operation at Ambatovy are compared with the design parameters, with emphasis on the behavior of iron.INTRODUCTION The main component of nickeliferous laterite ore is iron, and the Ambatovy deposit in Madagascar is no exception. The Ambatovy ore is primarily limonitic in nature, containing about 40 to 45 wt.% Fe and 1.1 wt.% Ni. Since the nickel content of the ore is roughly one fortieth that of iron, successful recovery of nickel depends on close control of the behavior of iron in the selected process. Exploration of the Ambatovy area, which is located to the east of Antananarivo, the capital of Madagascar, dates back to 1960, when the Malagasy Service Géologique carried out a limited pitting and auger-drilling program. Phelps Dodge Corporation (now Freeport-McMoRan Copper & Gold, Inc.) was granted the mining rights to the property in 1995 and carried out significant resource definition, environmental assessment and engineering studies between 1995 and 2001 (Chou, Rooke, Williams, & Hanks, 2000). In 2003, Dynatec Corporation, which was formed in 1997 by the merger of Dynatec International Ltd. and Sherritt International Consultants Inc., signed a joint venture agreement with subsidiaries of Phelps Dodge to evaluate the Ambatovy Nickel Project. Dynatec then became extensively involved in the development of the project, including process selection and pilot plant testing in Fort Saskatchewan (Collins et al., 2004, 2005, 2009; Collins & Vardill, 2005). Dynatec acquired 100% of the project in 2005 and a joint venture between Dynatec, Sumitomo Corporation, Korea Resources Corporation (KORES), and SNC-Lavalin Inc. (SLI) was formed shortly thereafter to provide funding for further development. SLI was responsible for engineering, procurement and construction management of the commercial facilities. Sherritt International Corporation reacquired Dynatec Corporation, including 40% ownership in the Ambatovy Nickel Project, in 2007. The current Ambatovy Joint Venture consists of an integrated nickel and cobalt mining, processing, refining and marketing enterprise between subsidiaries of Sherritt (40% owner and mine and plant operator), Sumitomo Corporation (32.5% owner) and KORES (27.5% owner)."

Jan 1, 2016

By M. England

Keywords: Bi-directional tests, Osterberg cell, O-cell®, static load tests, Timeset® Static load testing, where loads are applied vertically to the top of the pile and often referred to as 'top down testing', has been used for many years and has become a 'standard' test for the world of foundation engineering. The method, although well developed, cannot be used under certain circumstances, magnitude of load being a particular issue. There is a finite limit to the load capacity that can be applied with either kentledge, the use of reaction piles or anchors, and as the loads increase, the costs escalate dramatically. A novel test method seeks to overcome all the associated problems of large scale and restrictive area "top down testing", utilising static load testing techniques. The method requires the foundation element to be divided into two or more sections and these can be loaded axially as required using a portion of the foundation element as a reaction. This paper presents some recent applications and developments in the use and application of the bi-directional testing technique using the Osterberg Cell or O-cell® and outlines some of the many advantages of the system. Recent bi-directional test loads applied to bored piles have mobilised capacities of 279 MN and with flight auger piles up to 25 MN.

Jan 1, 2006

By W Barry Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire, Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1992