Search Documents

By Kenneth N. Pike

The need to comply with environmental regulations and increase production has resulted in modifications to the East Penn blast furnace operation. Changes made include furnace design modifications, closed loop water cooling with heat recovery, automated weighing and charging, automated tuyere punching, ammonia scrubbing of tail gases and improved metal and slag handling to minimize environmental impact. These changes have resulted in a marked increase in yearly production and compliance with many of the air, water and solid waste regulations.

Jan 1, 1990

By Michael L. Free

Bacterial oxidation of an arsenopyritic gold-ore .concentrate was carried out with continuous-flow .operation in 14-liter, mechanically agitated reactors. Samples from the slurry reactors were separated into solid and liquid fractions and analyzed separately to determine the electrochemical rates of sulfide conversion by the bacteria and the rates of direct bacterial oxidation of sulfide. The rates of the individual mechanisms are compared to the overall rates of biooxidation in the continuous-flow slurry reactors. The results show that the commonly hypothesize4 direct and indirect mechanisms of biooxidation both play a significant role in the bacterial oxidation of sulfide ores.

Jan 1, 1991

By S. N. Lekakh

Experimental work and thermodynamic simulations of cast iron refining were carried out using various additions of alkali and rare earth metals. The refining reactions for sulfur and oxygen removal were studied for melts treated with Mg, Ca, and Ce. The measured data and the results of the computer simulations were in agreement. Experimental kinetic data, together with the thermodynamic calculations, were used for optimization of the amount and sequence of the addition of nodulizers for ductile iron production.

Jan 1, 2009

By Nozomu Hasegawa

The phase diagrams and microstructures of the slags in the Mitsubishi Continuous Copper Smelting and Converting Process were studied for the prevention of the magnetite troubles such as accretion build-up on furnace hearths and launders, blockages at the melt outlet, slag viscosity increases and so on. According to the results of those studies, the silica and lime contents in the silicate slag at the smelting furnace, and the lime content in the lime-ferrite slag at the converting furnace were changed, resulting in lower and more consistent copper levels in the discard slag, with much less need for operators to clean melt outlets and launders. However, these changes may decrease the desirable amount of accretion-coating inside the furnaces and thereby reduce furnace campaign lives. Therefore, a method of estimating the magnetite level in the melts was developed, and slag compositions and temperatures have been controlled within the appropriate ranges to prolong furnace lives and also prevent magnetite troubles.

Jan 1, 2003

By Jr. Napolitano, Jr. Sanders

"Morphological evolution of a dendritic growth front in a binary alloy is simulated using a cellular automaton approach to establish the feasibility of modeling such growth with a local rule-based scheme. The motivation for this work is derived from the need to predict the development of solidification structures within real components of complex geometry, where significant constraint of the thermal and solutal fields may exist. Such cases present complex boundaries and large domain sizes, which may preclude the effective use of more conventional methods. In this work, a model is presented which couples a two-dimensional alternate-direction-implicit finite-difference diffusion solution with a cellular automaton growth algorithm to simulate morphological evolution in alloys solidifying under directional growth conditions. Temperature, composition, and interface curvature are incorporated into a local growth potential which is used by the automaton, allowing the interface to evolve. Alloy solidification is simulated over a range of experimental conditions, producing various structures. Issues addressed include morphological instability, primary spacing selection, interface curvature, microsegregation, and tip conditions.IntroductionThe development of dendritic structure plays an essential role in alloy solidification. Virtually every microstructural feature, within a cast alloy component, is related to the interface morphology present during solidification. Conventional solidification theory, describing dendrite tip kinetics and mushy zone phenomena, provides a means for estimating overall microstructural parameters for an alloy solidified under steady-state conditions. Microstructural prediction for actual components, which are finite in size and complex in geometry, requires a description of the evolution of the interface morphology under transient conditions and geometrical constraint and an understanding of how the structure propagates through the mold. Any useful simulation tool must be equipped to handle these circumstances within the limits of computational feasibility."

Jan 1, 1998

By Batric Pesic

The interactions of mineral-pyrite with T. ferrooxidans were studied by using a cyclic voltametry technique. The interactions with bacteria were examined during the entire growth stage of bacteria (fermentation), The pyrite ?surface invariably drastically changed ' its. properties at the second day of fermentation. Beyond two .. days of fermentation, the cyclic voltamograms were insensitive to convective diffusion produced by stirring. The product layer was examined by SEM,. X-ray diffraction and chemical analysis. The SEM study revealed that bacteria populated the pyrite surface at an extremely high density levels. The high density of bacteria, and the solid reaction products formed on the pyrite surface created conditions for pore diffusion which explained why the CVs became .insensitive to convective diffusion in solution (stirring). The x-r:ay diffraction study confirmed jarosite as a product layer. A mechanism of T. ferrooxidans cells serving as nucleation sites for jiarosite formation is proposed.

Jan 1, 1991

By G. Gomathi, K. Asokan, K. Subramanian

An electrochemical reactor with anode and cathode chambers separated by a composite perfluoro polymer cation exchange membrane was designed, fabricated and used for the reduction of dissolved carbon dioxide under ambient conditions to formate. The flow reactor enhanced the mass transfer of carbon dioxide compared to the batch reactor. Experiments were conducted using two different perfluoro polymer membranes - Nafion 961. Efficacy of CO2 reduction on various cathode materials (Cd, Pb, Sn and Zn plated stainless steel woven mesh) were determined. Optimum values of flow rate and current density were evaluated for the energy efficient formation of formate in aqueous KHCO3 (pH 7.5-8.5) buffer solutions.

Jan 1, 2008

By Batric Pesic

Adsorption of gold on activated carbon from gold bromide solutions was examined as a function of pH, particle size, carbon amount, initial gold bromide concentration, bromine concentration, temperature, and various cations and anions. pH did not have any effect below pH=6. Above pH=6, pH had dramatically negative effect. The adsorption results satisfied a first reaction order model. The reaction rate constant was proportional to the inverse of carbon particle radius. It was also proportional to the amount of carbon, and independent of initial gold concentration. Temperature had a very little effect at pH=l. At pH=8, the activation energy was a function of the extent of a reaction, increasing with the extent of a reaction. Cu, Fe, Ca, Mg, and Na cations and sulfate, chloride and bromide anions did not have any effect on gold adsorption. Bromine had a very negative effect on gold uptake.

Jan 1, 1991

By Jian Li

Corrosion resistance of materials is highly dependent on the microstructure of the specific material. Apart from general corrosion rate measurement using techniques like linear polarization and A.C. impedance, microstructural investigations are frequently needed to identify the root cause of corrosion. Advanced techniques, including scanning electron microscopy (SEM) and transmission electron microscopy (TEM), have been well integrated into routine characterization studies. Other microscopy techniques, including electron probe micro-analyzer (EPMA), Auger, X-ray photon spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS), can provide detailed chemistry information on corrosion products. In recent years, focused-ion beam (FIB) microscopes have evolved into an important microstructural characterization instrument. In this study, corrosion of rebar encased in concrete was studied in great detail using advanced microscopy techniques. Corrosion product on the rebar surface was identified as ferrous oxide with relatively large crystal size. The morphology of this passive layer was thoroughly analyzed, and its formation mechanism is proposed.

Jan 1, 2009

By Charles Zimmerman

The Genesis gold mine, owned and operated by Newmont Gold Co., is located in section 31, T36N, R50E within Eureka County, Nevada along the Carlin Trend of sediment-hosted disseminated gold deposits. Mining commenced in 1986 with present mineable and stockpiled reserves listed at 17,711,000 tons of ore averaging 0.073 opt Au, totalling 1.292 million ounces of gold. Ore is primarily hosted within Devonian calcareous siltstones that have been subjected to intensive argillization and silicification episodes. Additional mineralogic and geochemical features of the Genesis ores include enrichment in iron-oxides, kaolinite, arsenic and antimony; the ore zone is relatively depleted in carbonates and sulfides as a result of supergene and hypogene oxidation. Two major structural zones enhanced the permeability of the siltstones and served as the main hydrothermal conduits within the deposit. Prior to the main ore stage, the host rocks were subjected to metasomatic effects caused by emplacement of the Juro-Cretaceous Goldstrike granodiorite pluton and associated dikes and sills. Micron-size gold occurs in clays, micro-crystalline quartz, and in arsenical complexes. Non-oxidized carbonaceous and sulfidic ores and silica-locked ores result in variable preg-robbing and refractory responses during cyanide recovery. Selective mining and milling has resulted in the successful treatment of the Genesis orebody.

Jan 1, 1988

By Hiroshi Nakajima, Kotobu Nagai, Toshihiro Hanamura

"Low carbon ferritic steel bars with ultra-fine grain structure was developed through a warm rolling for the first time by the present authors. They show better low temperature toughness than conventionally hot-rolled plates. Hence, the brittle fracture surfaces in Charpy tests were examined in terms of the effective grain size of fracture, compared with those of conventional QT steels. The ductile-to-brittle transition temperatures were in good accordance with those for the QT steels if referred to the effective grain size of fracture: · However, the size was a few times that of the ferrite grain. This means the grain refining is not yet fully utilized from the viewpoint of low temperature toughness. The anisotropy of· the impact properties and the annealing effect of highly dislocated structure on the toughness are also discussed in the present paper.IntroductionFor structural materials, both high strength and good toughness are required. Well-known approaches for obtaining better toughness for steels are as follows:1) Grain refining2) Addition of Ni3) Thin plate effect by cracking parallel to the rolling direction prior to crack propagation4) Contribution of metastable austenite.Among them, only the grain refining can raise the strength and improve the toughness. And it is well known that the finer the ferrite grain size, the lower the ductile-to-brittle transition temperature. For example, in the case of 0.11 carbon steel, the transition temperature decreases linearly to in d 1/2 [1 ]. However, these have been told in the regime of coarse grain size that is larger than 10 µm in diameter. There ~as .been no study dealing with the low temperature toughness in the regime of ultra-fine grain size with a diameter in the order of 1 µm."

Jan 1, 2000

By J. A. Eisele

There is currently much interest in how extraction of gold and silver from ores with acidic thiourea solution compares with extraction using alkaline cyanide solution. Agitation leaching tests were performed by the Bureau of Mines on 14 precious metal ores using sodium cyanide (?NaCN) and thiourea [(NH2)2CS) as extractants. The objective was to compare the results of the two extractants. NaCN was used at a concentration of 2 g/L with and without H202 as an oxidant. (NH2)2CS was used at concentrations of 2 and 20 gjL, and the solution potential was controlled at 390 to 420 mV standard hydrogen electrode (Eh) with Fe2(S04)3. With both reagents a.t 2 g/L extractant levels, NaCN extracted more gold and silver than (NH2liCS from all of the ores. At 20 g/L (NH2)2CS compared with 2 g/L NaCN, (NH2)2CS extracted more gold than NaCN from two ores, the same amount from one ore, and more silver from one ore. NaCN extracted more gold than (NH2 )2CS from 10 ores and more silver from 4 ores.

Jan 1, 1989

By Kenshi Kawabata, Mitsuji Ueda, Junko Umeda, Katsuyoshi Kondoh, Kantarou Kaneko

Solid-state recycling process of in-house scraps of machined magnesium (Mg) alloy wastes has been established to directly produce wrought materials via the repetitively plastic deformation by Roll-compaction (RCP) and the conventional hot extrusion. The coarse chips, wasted in machining AMX602 (Mg-6Al-0.2Mn-2Ca) cast billets used for the gate bar used in Electronic Toll Collection (ETC) of the high-way system, were employed as the input materials in this study. RCP process enabled to serve coarse Mg alloy powder consisting of refined grains and intermetallics with no re-melting. They were easily consolidated by hot extrusion, and their wrought alloys showed both homogeneously refined grains less than 1~2 µm by dynamic recrystallization and randomized texture by repetitive plastic deformation on the input wastes. These materials revealed extremely advanced mechanical properties of high tensile strength of 356MPa and high ductility of 14.8%, compared to the originally virgin materials with 270MPa TS and 5% elongation. When applying the same Mg alloy wastes via RCP process to the mass production in the company, the large-scale extruded materials also indicated the superior tensile properties. It means that this direct solid-state process is held as “Up-grade recycle of metal wastes”.

Jan 1, 2008

By Bogidar Mihaylov

A laboratory study was conducted on continuous precipitation of copper, cadmium, mercury and arsenic using thiourea, thioacetamide, sodium sulfide and ammonium sulfide as precipitating agents. Depending on the experimental conditions the metals precipitate with the sulfide donors at different orders and rates. These differences were employed as a basis of several techniques for continuous separation of copper and arsenic, cadmium and arsenic, mercury and copper, and copper, mercury and arsenic. The separation of the metals from industrial waste solutions was also studied. The precipitates obtained were inspected using x-ray diffraction, scanning electron microscope, atomic absorption spectrometer and plasma particle counter.

Jan 1, 1992

By Katsukiyo Marukawa, Manabu Iguchi, Sigeta Hara, Shinichiro Yokoya, Sigeo Takagi

"A numerical analysis and water model study of the mold region of a continuous casting apparatus was performed with a novel injection concept using swirling flow in the pouring tube, to control the heat and mass transfer in the continuous casting mold.As a result, the following results were found:1) By changing swirl strength, it is easy to control the flow pattern as well as the direction of the flow.2) Uniform velocity distribution can be obtained within a very short distance from the outlet of the nozzle.3) Heat and mass transfer near the meniscus can be remarkably activated compared with a conventional straight type immersion nozzle without swirl.4) Swirl helps the superheat in the melt dissipate.S) Penetration depth of nozzle outlet flow is decreased remarkably by the application of swirling.6) For the case without swirl, the peak of the flow moves near the mold-wall with flowing down from the outlet of the nozzle due to the Coanda-effect. On the other hand, peak of the flow moves near the mold axis with flowing down from the nozzle-outlet within considerable short distance, namely axi-symmetric velocity distribution can be obtained within very short distance from the nozzle-outlet.Those findings mentioned above are very useful to control the flow pattern in the billet and bloom continuous casters."

Jan 1, 2001

"Hematite pellets were electro-deoxidized to iron in molten sodium hydroxide to produce iron containing about 10-wt % oxygen. The anodic reaction was the evolution of oxygen on an inert nickel anode. Before the electrochemical reaction, there is a reaction between sodium hydroxide and ferric oxide to form sodium ferrite and, in order to compensate for the reduction in sodium oxide content, 1 wt % sodium oxide is added to the melt. In a laboratory cell, the cell voltage was 1.7 V with a current density of 5000 A m-2, a current efficiency of 90% and an energy consumption of 2.8 kWh kg-1.Introduction The iron and steel industry contributes about 2.3 bn tonnes/annum of the carbon dioxide to the atmosphere, which is about 10% of the total, and some believe that, in order to prevent a catastrophic rise in the earth’s temperature, carbon dioxide emissions must be reduced by 50% come 2050. However, by 2050, it is likely that the iron and steel industry would have grown significantly so that the production may have risen to 2 or 3 bn tonnes/year so in order to meet the 50 % reduction on today’s figure, the carbon dioxide may have to be reduced to 25% or less, which is a very demanding requirement. There are probably three ways of reducing the carbon dioxide output:1. By capture and sequestration, but this may be technically very demanding.2. Reduction using hydrogen in place of carbon."

Jan 1, 2009

By I. Gaballah

High and low grade concentrates of tantalum and niobium oxides were obtained by leaching a medium grade tin slag. Chlorination and carbochlorinalion of these concentrates were studied between 200 and 1000 "C. Chlorination or carbochlorination of the low grade concentrate led, at 1000 OC, to the extraction of about 95 % of the tantalum and niobium oxides. However, the tantalum and niobium chlorinated compounds were contaminated by iron and manganese chlorides. Complete extraction of the niobium and tantalum pentoxide was achieved during the carbochlorination of the high grade concentrate at 300 and 500 "C, respectively. While chlorination of this concentrate at 1000 "C, allowed to the volatilization of about 60 and 80 % of Ta205 and Nb205. In both cases, condensates were composed of almost pure tantalum and niobium chlorinated compounds. The results demonstrate the advantages of the lixivialion based on the "pseudo- structure" of the raw tin slag to obtain the high grade concentrate. The conclusions of this work suggest that the carbochlorination of the high grade concentrate is an efficient process for the extraction of refractory elements from tin slag.

Jan 1, 1993

By D. J. Adams

Cyanide heap leaching is the predominant technology used in processing low-grade gold ores. During closure ora heap leach operation, residual cyanide must be removed from the process and waste solutions, as well as the heap. Biological cyanide oxidation is a proven, economical technology for destroying cyanide in process and waste waters and spent heaps; The use of biological cyanide degradation eliminates the need for toxic or corrosive chemical oxidizers and has- been implemented at full scale at treatment costs usually <$0.50/1,000 gal. The Applied Biosciences biological cyanide destruction (BCND?) process has been demonstrated to effectively treat cyanide, concentrations up to 350 mg/L. Treated process solutions and wastewaters also contained other contaminants such as arsenic, copper, iron, silver. selenium, mercury, nitrate and zinc, much of which was removed in the cyanide degradation process. Under optimal conditions, microorganisms can rapidly oxidize free cyanide in some process solutions from over 250 mg/L down to 0.1 mg/L in 4 to 5 hr. Cyanide is degraded to ammonia and carbon dioxide, with 50%ofthe cyanide carbon liberated as C02. In general, carbon tank based bioreactors degrade cyanide at significantly higher rates than process or wastewater pond configured treatments, which usually degrade cyanide-more rapidly than in heap treatments. Investigation of cell-free enzyme preparations as an alternative to live microbial cyanide degradation shows promise. Advantages of enzymes over live microbes for cyanide degradation include: (I) the ability to tolerate and degrade higher cyanide concentrations (> I ;000 mg/L), (2) nutrients to support live microbial cells are not required, (3) the effects of other toxic contaminants, such as metals, found in mining waters-are eliminated and (4) the potential for greatly increased kinetics.

Jan 1, 1998

By Grigore Matei

The thermodynamic properties of CU2S-FeS system are important not only in the case of copper smelting but also in the case of general pyro-mctallurgy, However there are not many reported activity data In this study, activities of FeS and CU2S in the CU2S-FeS system were calculated using the Darken&apos;s method from the activity data of the CU2S-FeS-Sb2SJ systems measured by the transportation method at 10S0°C. The activities of CU2S and FeS in the CU2S-FeS system showed negative deviation from the ideal behaviour and satisfied the relation of the Gibbs-Duhem equation,

Jan 1, 2003

By Ying Li, Xuling Chen, Xiaohui Fan

"In the sintering process, the behavior and performance of iron ores is extremely complex. Different minerals have different sintering properties. In order to use iron ores rationally and effectively, multilevel fuzzy evaluation method is used to establish the comprehensive evaluation model of iron ores. Because of the relative independent characters of iron ores in sintering process, the characters can be divided into physical and chemical properties, granulation performance, and sintering properties, are divided, and together with iron ores prices as the first level index for judging, which are used as the second level index for judging. Using the analytic hierarchy process (AHP) to determine the weight of each index, which is used as the second level index. The relative membership matrix is determined by triangular membership function, the comprehensive evaluation model is established.IntroductionIn China, sintering is the main method for iron ores agglomeration. Sinter accounts for more than 80% of the blast furnace. Sinter production in the iron and steel enterprises in China plays an important role[l-2]. As the main raw material of iron ores sintering, the objectivity and integration of iron ores evaluation is essential. The iron ores evaluation methods include of metric ton price evaluation method, iron grade of a single iron ores sintering, acid-base balance method, composition assessment method and other methods which are based on the chemical composition and physical properties of iron ores to measure the quality of iron ores[3]. The high-temperature mineralization is an important process in sintering process, which affects the structure and mineral composition of the sinter, and has a close relationship with the quality of the sinter[ 4]. Therefore, in consideration of the physical and chemical properties, granulation properties, mineralization performance and sintering properties, the iron ores are evaluated by multi-level fuzzy comprehensive evaluation. The multi-level fuzzy comprehensive evaluation method makes a comprehensive evaluation, applying fuzzy transform principle and maximum membership degree principle, considering a number of factors related to the things which are evaluated. The method has lower requirements for the amount of data, and which integrates qualitative with quantitative judgment. It has a unique advantage to make up for the deficiencies of traditional evaluation methods. It also can comprehensively evaluate the iron ores in a relatively short period, reduce a lot of experiments, improve efficiency and guide the sinter production[5-6]."

Jan 1, 2013