Search Documents

By Takayuki Watanabe, Yoshiki Shimizu, Yusuke Moriyoshi

"B-C-N nanotubes prepared by a flush evaporation method using a de arc plasma were mainly characterized by transmission electron microscopy (TEM) and electron energy· loss spectroscopy (EELS). The nanotubes obtained· were divided into three types such as carbon boron nitride and carbon or carbon nanotubes surrounded with boron nitride nanotubes. These types of nanotubes were obtained at higher temperatures than about 3000 K, however, these were not formed at lower temperatures than about 3000K. On the other hand, 11anocapsules were· formed at all the experimental temperatures and nanocapsules with a homogeneous phase were obtained at lower temperatures than about 3000 K. The effect of additives on the formation of B-C-N nanotubes was not clear. Based on these experimental data depending on temperatures and corresponding microstructures, the formation mechanisms of both nanotubes and nanocapsules were briefly .discussed 1 Introduction As reported previously, nano tubes have unique electrical properties1, 3) The preparations of nallotupes have been usually carried out by flush evaporation methods using either a de arc plasma or a laser4 -5) By these methods the reaction rate is so rarid that we have no data of intermediate products between initial raw materials and. final products of nanotubes 6-9). So, the formation mechanisms of nanotubes have been mainly speculated only from the microstructures of resultant nanoiubes. In order to have more reliable formation mechanisms, it is particularly important to have the information of intermediate products at the corresponding temperatures. From the viewpoints, we have studied about the effects of temperatures on the preparation of nanolubes. Here we report mi firstly some problems on the preparation of B-C-N nanotubes 10), secondly the effects of temperatures on the preparation of B-C-N nanotubes, and finally the formation mechanisms of nanotubes."

Jan 1, 2000

By J. D. Sloop

This paper discusses the current state of EAF dust recycling at AmeriSteel's Dust Processing Division in Jackson, Tennessee. Included are a brief history of the plant, a description of the facility, a description of the process, and operating data.

Jan 1, 2000

By H. M. . van der Donk

In this work an overview is given about the techniques available for the removal of metallic impurities from molten aluminium. The overview is focused on the removal of iron. Also, some experimental results are given about the creation of iron-rich intermetallic compounds in an aluminium system, which are subsequently removed by gravity segregation and filtration techniques. This work is part of an ongoing research project of three major European aluminium companies who are co-operating on the subject of recycling of aluminium packaging materials recovered from household waste by means of Eddy-Current techniques. Using this technique the pick-up of some contaminating metals, particularly iron, is almost unavoidable.

Jan 1, 1995

By Y. W. Chung, W. I. Chia

"The interaction of water vapor with single crystal Ni3(Al,Ti) and polycrystalline Ni3Fe, with and without the presence of oxygen, has been studied with Auger electron spectroscopy, photoemission spectroscopy, thermal desorption and isotope exchange. Water dissociates to produce atomic hydrogen above 200 K on both Ni3(Al,Ti) and Ni3Fe surfaces. For Ni3(Al, Ti), the reaction is structure-sensitive. Pre-adsorbed or co-adsorbed oxygen on Ni3(Al,Ti) and Ni3Fe significantly suppresses hydrogen production due to water dissociation. This suppression process occurs more efficiently on Ni3Fe than Ni3(Al, Ti).IntroductionOrdered intermetallic compounds such as aluminides, silicides and titanides are very attractive for structural applications at high temperatures. This is because these intermetallics tend to form adherent oxides in oxidizing environments which protect the base materials from excessive oxidation and corrosion. In addition, they have low density, relatively high melting points and good high-temperature strength. However, the moisture in air severely embrittles many ordered intermetallics such as FeAl [1-3], Fe3A1 [4,5], C03Ti [6,7], (Co,Fe)) V [8], Ni3Si [9], Ni3(Si,Ti) [10], Ni3(AI,Mn) [Ill, and Ni3A1 [12-14], resulting in low 'ductility and brittle fracture at room temperature. Recent studies by Liu and coworkers (see review by George and Liu [15]) provide a qualitative description of the mechanism for this moisture-induced embrittlement. During elongation testing, cracks are formed, thus exposing fresh alloy surfaces. One or more active components of the alloy react with water vapor in the environment to produce atomic hydrogen which penetrates into crack tips and causes hydrogen embrittlement. This is similar to that proposed for moisture-induced embrittlement of aluminum alloys [16]."

Jan 1, 1996

By M. Sakamoto, S. Karaswa, Y. Yoneoka, Y. Ohmizo

"The Annaka Refinery has been processing leach residue by Waelz process for 17 years. Recently, the quantity of the leach residue has increased due to a decline in the quality ~f zinc concentrate. Meanwhile, negative factors (e.g. deterioration of water balance due to improved electrolytic power consumption rate) have increased· in the processing of the leach residue.We have implemented various measures in responses to this situation, while striving to increase ·processing capacity and achieve stable operation. AS we have largely completed our assessment of the efficacy of these measures, we report on our recent process improvements.IntroductionWe have been treating leach residue by the Waelz kiln process since 1981. At that time, treatment of only 50,000 tons of leach residue per year was anticipated. However, subsequent process improvements have revised this figure up to 75,000 to 80,000 tons per year.However, today's increased Fe zinc concentrate grade has resulted in increased amounts of leach residue. In addition, improvements have reduced electrolytic power consumption rate of zinc electrolysis, limiting the amount of water that can be used in ·the zinc refining processes and for deaning leach residue. Consequently, we encounter an increasing number of problems and factors adversely affecting leach residue treatment, including increases in water-soluble Zn (WsZn) and. S (S04) in leach residue.To solve these problems, we have taken several measures to ensure long-term continuous operation and treatment of this increased · amount of leach residue. This paper discusses these measures."

Jan 1, 2000

By Neil Rowlands

Particle liberation studies are commonly used in the determination of the proportion of locked and liberated phases in ground ores at various stages of mineral processing. These studies may range from a qualitative assessment of a polished specimen in an optical microscope to a full quantitative analysis of the liberation characteristics of fine grained complex sulfide ores using scanning electron microscopy and high level image analysis. However, the conversion of quantitative data to meaningful information on a mill operations level is by no means a simple task. This paper reviews the errors inherent in the SEM/Image Analysis technique and looks at the various methods available to minimize errors in data collection.

Jan 1, 1992

By T. Asahina, M. Nakamura, M. Mabuchi, I. Shigematsu, M. Nakanishi, G. Yamauchi

"Commercial stainless steels (SUS304L and SUS430) were subjected to equal channel angular extrusion (ECAE) at room temperature to a total strain of 2.3 to 9.2. For each type of stainless steel, it was shown that the sample processed by ECAE showed higher room temperature strength than the as-quenched sample. This is probably due to the heavily worked structure. On the other hand, both strength and elongation of the ECAE processed SUS430 were increased by annealing at 773K. It is likely that higher strength is attributed to both the heavily worked structure and fine substructures. It is also likely that higher elongation is attributed to the fine substructures. It is concluded that ECAE is available for improving the room temperature strength of commercial stainless steels.INTRODUCTIONEqual channel angular extrusion ( ECAE ) is a technique that provides the repetitive deformation and allows to high intensity of deformation. With this procedure, a sample is pressed through a channel that has an equal cross section but bent at an angle of ?> [1-2]. Shear strain is introduced when a sample passes through the bending point of the channel. Repetitive processing is feasible because the cross-sectional dimension of a sample has no change during processing. To date, many reports have described that ECAE is available for the fabrication of fine-grained materials [3-14]. On the other hand, an ECAE processed sample can achieve high intensity of deformation through repetitive deformation. According to the equation given by Segal [ 2 ], a strain of about 1 is introduced in each pass through die if the angle ? is 90 deg.It is well known that high tensile strength can be achieved in metallic materials through work hardening [15]. It is also known that metallic materials with fine grain size show high strength [16]. Hence, it is expected that ECAE is available for strengthening method in metallic materials. In the present paper, we will report the mechanical properties of stainless steels processed by ECAE. As samples, SUS304L austenite stainless steel and SUS430 ferritic stainless steel were chosen. Each alloy has a single-phase structure (fee or bee) and shows no phase transformation, so that transformation strengthening cannot be applied. Hence, a heavy cold work such as ECAE may be effective for strengthening of this stainless steel. Annealing was conducted for the ECAE processed SUS430 to vary its microstructure. Then, the effect of annealing on the strength of the ECAE processed SUS430 was also investigated."

Jan 1, 2000

By Chunlin Chen

Nickel-sulfide minerals are normally associated with copper and iron sulfides and often contain a minor amount of valuable metals such as cobalt and detrimental impurities such as arsenic. Metal losses in slag vary from process to process during the pyrometallurgical production of nickel and, depend on the feed composition, slag chemistry and operating conditions. Maximiz the metal recovery is one of major considerations to optimize operating condition for nickel smelting/ converting processes. At the same time, the deportment of minor elements between various phases during nickel smelting is of great importance by smelter operators. The Multi-Phase Equilibrium (MPE) is a thermodynamic package developed by CSIRO for simulating reactions between phases in multi-component and multi-phase systems [1]. Over the years the capability of the MPE model has been extended to cover the behavior of a large number of elements in high temperature systems. The sulfide smelting module of the MPE, which covers the minor elements such as As, Bi, Sb, Pb, Se, Te, Sn, Co and Zn, is capable of modeling the deportment of major and minor elements between various phases during nickel smelting. In this article the application of the MPE model in modelling the nickel smelting process is presented. The modelling results on the majors and minors are compared with the plant data. The deportment behaviour of arsenic in nickel smelting was analysed and the impact of slag chemistry on slag properties was modelled. These results can assist process metallurgists in exploring the optimum fluxing strategy for smooth operation and the potential practices for improving arsenic removal.

By Xudong Liu, Feng Chen, Yufeng Guo, Wei Chen, Tao Jiang

Willemite is typically found in oxidized zinc ores and metallurgical secondary resources but without effective extraction method yet. Based on the ideas of zinc phase reconstruction in the willemite, the extraction of zinc from willemite by calcified-roasting using CaO as additive and ammonia-leaching process was studied in this paper. The influences of CaO dosage, roasting temperature, roasting time on the phase transformation and zinc leaching rate were studied, which were characterized by XRD. The results indicated that Zn2SiO4 was transformed into ZnO or Zn2CaSi2O7 .After roasted with 1.4 times of theoretical CaO dosage at l280 for 40 minutes, willemite was thoroughly transformed into ZnO. The zinc leaching rate of the roasted sample was 97.45% in NH4Cl-NH3 H2O leaching system, which increased by 91.40 % compared with zinc leaching rate of 6.05% when willemite was directly leached in NH4Cl-NH3 H2O system.

Jan 1, 2016

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

By J. P. Evans

The modem copper smelter today utilizes tonnage oxygen for smelting concentrates, generating a high strength S02 off-gas leaving the smelter vessel. This gas stream, which also contains any unreacted oxygen, plus C02, N2 and H20, also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates. The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals in the off-gas circuit. Depending on this history, the type and characteristics of the chemical and physical reactions which. occur in the gas handling system can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries .and design, on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data, several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By M. J. Collins

A hydrometallurgical process has been tested at the Sherritt Research Centre for separation of zinc, lead, copper and precious metal values from the zinc oxide fume leach residue stockpiled at the HBM&S operations in Flin Flon, Manitoba. Zinc is found primarily as zinc femte and sphalerite in the residue, lead as lead sulphate and jarosite, and copper as sulphide and jarositic compounds. Gypsum and siliceous gangue are significant diluents. The separation process includes hot acid, atmospheric and reducing (sulphur dioxide) leaching; zinc, copper and lead flotation; and atmospheric iron removal steps. Zinc is recovered to a high strength zinc sulphate solution and to a zinc sulphide concentrate suitable for feed to a roaster or to a zinc pressure leach plant; lead to a high grade lead sulphate concentrate suitable for feed to a lead smelter, and copper to a high grade copper sulphide concentrate suitable for feed to a copper smelter. Precious metals are divided between the zinc, lead and copper concentrates.

Jan 1, 1993

By R. R. Odle

A laboratory and pilot-scale investigation of direct smelting of copper concentrates was conducted to determine the effect of concentrate analysis and the degree of roasting on the yield and quality of copper produced in a subsequent smelting step. A stoichiometric :mOdel of direct smelting is presented which predicts the? quantity of copper; slag, and white metal' prOduced'and the distribution of copper in these phases as a function? of the concentrate '(calcine) analysis.

Jan 1, 1983

By B. C. Jena

In a chromite smelting process for the production of high-carbon ferrochromium, the slag composition profoundly affects operating conditions and the economic performance of the process. For a Canadian chromite concentrate, optimum slag composition and operating temperature were determined by process simulation with a computer model, which is based on parameters, such as the minimisation of slag volume, liquidus temperature, electrical energy consumption and chromium losses. Chromium recoveries are identified for slag compositions spanning wide concentration ranges within the quaternary system MgO-AI2O3- SiO2-CaO. The simulated data are compared with the experimental results.

Jan 1, 1994

By Ji-He Wei

The ESR of Cu-Cr-Zr alloy has been experimentally investigated. The remelting experiments have been carried out with different slag fluxes in the Cal, + Nal, CaF2 + ZrO2 and CaF2 + NaF + ZrO2 systems on an ESR furnace of 25kg capacity; using a water-cooled copper mould of 96.5 mm diameter, with the forged square bar electrodes of 50x50 mm2. The slag amount was taken to be 1.5 kg. The remelting current and voltage used were 1600-1800A and !5-25K, respectively. The influence of the slag composition on the stability of the remelting process and the losses of alloying elements (2r and Cr) has been considered and examined. The technologies of hot working and heat treatment of the ES ingot have been described and discussed. Some physical properties of the slag in a CuF2 + NaF + ZrO2 system and the remelted Cu-Cr-Zr alloy have been determined. The results indicated that with the slag flux of CaF2 + NaF + l0 mass % ZrO2 and the other operation parameters employed, a high quality ingot of Cu-Cr-Zr alloy may be obtained at the considerably high yields of Zr and Cr by means of ESR. For the remelted Cu-Cr-Zr alloy with a specified composition of 0.5 mass % Cr and 0.1 mass % Zr, the appropriate electrical conductivity, hardness and softening temperature are as high as 45-46S/m, HRB 82-84 and 550°C. respectively. The properties of the Cu-Cr-Zr alloy products are in accordance with and superior to the requirements and specifications of ISO5l82-l99l(E).

Jan 1, 2000

By P. Chris Pistorius

"Ilmenite smelting involves partial reduction of iron oxide from a slag consisting mainly of T1O2, T12O3 and FeO, yielding as products iron (with approximately 2% carbon) and titanium slag. Slag purity requirements preclude any fluxing additions, and the aggressive nature of the slag necessitates a furnace freeze lining. Large departures from thermal and chemical equilibrium hold in the smelter, with possible implications for process stability. The slag is approximately 150K. hotter than the metal, which means that the metal temperature is below the slag melting point; this difference in temperature has been shown to lead to formation of a solid TisOs-rich layer between the slag and metal. Recent equilibrium measurements have confirmed that the slag and metal are not in chemical equilibrium either, with significantly more reducing conditions in the metal than in the slag. After solidification, the pseudobrookite slag structure is metastable below approximately 1400K, and may transform upon slight oxidation.IntroductionThe natural mineral ilmenite is the main source of titanium, which is mainly used to produce Ti02-based pigments. Ilmenite has the ideal formula FeTiC>3, but natural minerals can be partially oxidized (to contain some Fe3+), and typically contain MnO and MgO as well, together with associated silicate minerals. Smelting is one of the methods to upgrade ilmenite for subsequent T1O2 pigment production; smelting involves partial reduction of FeO to form metallic iron as a byproduct and titanium slag as the main product. Reduction is typically controlled to yield a slag which contains around 10% FeO, 85% (Ti02+Tij03) and 5% impurity oxides (mainly MnO, AI2O3 and S1O2). An example of a typical average slag composition from reduction of South African ilmenite is shown in Table I. As this indicates, a significant side reaction is reduction of some T1O2 to T12O3. The relative extents of reduction of FeO to Fe and of Ti02 to T12O3 are such that the slag stoichiometry is close to that of the pseudobrookite phase [1]. Pseudobrookite has the structure AB2O5 (where ""A"" and ""B"" are different cation sites); the phase which makes up the bulk of solidified titanium slag has the AB2O5 structure and stoichiometry [2], and can be viewed as a solid solution of FeTi20s, T13O5, ÌçÔÀ2è5, MgTi20s, AI2T1O5 and C^TiOs [1]. This solid-solution phase is referred to as ""pseudobrookite"" or ""M3O5"" in this paper."

Jan 1, 2012

By Wenxian Zhu, Xuema Li, Patrick R. Taylor

"Experiments were performed in a non-transferred arc, thermal plasma flow reactor to investigate the synthesis of ultra fine boron nitride (BN) powder from the reaction system of boron oxide (Bz03), methane (CH4), ammonia (NH3) and hydrogen (H2). Argon (Ar) and nitrogen (N2) were used as plasma gases. The thermodynamics and kinetics of the synthesis reactions were examined and a chemical reaction mechanism was proposed. The powders produced under certain operating conditions had high purity and good conversions. All the products were extremely fine powders (< 30nm) and were uniform in size distribution. The powder products were analyzed by chemical and physical characterization. The effects of the reaction variables on the conversions from B203 to BN and the purity of the products were investigated.IntroductionIn the past few decades, boron nitride (BN) has attracted a great deal of interest because of its excellent thermal, chemical and electrical properties (1-4) It has a high thermal stability and thermal conductivity. Chemically, it is very stable and is not wetted by most molten metals and slag. It is also an excellent low loss insulator. Since hexagonal boron nitride (h-BN) is light in weight, strong and easily fabricated, it has applications in a variety of specialized high temperature areas, such as a high temperature lubricant, crucibles for molten metals, thermocouple protection tubes, break rings for horizontal continuous casting of steel, and friction reducing coatings. In cubic form, boron nitride is one of the hardest materials known, second only to diamond, and it is an excellent material for tools in which the use of carbon based materials is limited by oxidation or reaction with metals."

Jan 1, 1998

By J. P. Evans

The modem &apos;copper smelter today utilizes tonnage oxygen for smelting concentrates. ,generating a high strength S02 off-gas leaving the smelter vessel. This gas stream. which also contains any unreacted oxygen, plus CO2; N2 and H20. also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates, The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals, in the off-gas circuit. Depending on this history. the type and characteristics of the chemical and physical reactions which occur in the gas handling system &apos;can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries and design. on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data. several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By Kenneth N. Ham

Hydrometallurgy covers a wide spectrum of areas and its knowledge base is enlarged and enhanced by contributions from many other fields. Dissolution of metals and alloys in aqueous media will be used to illustrate how rich the field of metal extraction can be. Comprehensive understanding of the fundamentals of metal and alloy dissolution in aqueous systems requires creative application of thermodynamic principles, solutions chemistry, ligand complexation theory, electrochemistry, transport phenomena and heterogeneous kinetics. In addition, recent developments in instrumentation in the fields of interfacial phenomena and corrosion have tremendously advanced the field of metal extraction in aqueous system. The close relationship between metal extraction in aqueous systems and various physicochemical phenomena occurring in corrosion and interfacial systems will be discussed and illustrated with examples.

Jan 1, 2002

By Chen Song

In the experiments of purifying the solution of chlorine leaching from nickel concentrate with N235, the effects of organic phase composition on purifying efficiency have been studied. From the results obtained, the optimal organic phase composition is found to be 25%N235+12%isomerous alcohol +63%sulfonic kerosene (VIV) and the saturated content of cobalt in organic phase is7.95 g*dm3. And then the serial experiment is carried out. The results show that at the given organic phase composition, the purified solution contains p(Ni) >200 gm dm3, p(Ni)l p(Co) >50000 and the contents of Cu, Fe, Mn, Zn meet the technical criterion of standard nickel electrolyte. The cobalt chloride solution contains p(Co) >I10 g L-1, p(Co) lp(Ni)>50000 and the enrichment of cobalt has been achieved.

Jan 1, 2006