Search Documents

By Dae Jin Ha

Sticking phenomenon occurring during hot rolling of two STS 430JlL ferritic stainless steels was analyzed by hot-rolling simulation tests. The sticking started from the initial nucleation stage in which the rolled materials were stuck onto the roll specimen surface, proceeded to the growth stage in which stuck fragments grew further, and reached the saturation stage. The modified 430JlL steel had a smaller number of sticking nucleation sites and slower growth rate than the conventional 430JlL steel because of higher high temperature hardness, thereby leading to less serious sticking. When the simulation test was conducted at 1070 °c, Cr oxides were formed on the surface of the rolled materials, and thus the sticking was drastically reduced because of the increased surface hardness of the rolled materials. In order to prevent the sticking, high-temperature properties of the rolled materials should be enhanced when rolled at 900°C or 1000 °C, and rolling conditions and alloying compositions, under which the oxide formation was promoted, were more important than high-temperature properties when rolled at higher temperatures than 1000 oC.

Jan 1, 2008

By Henrique Kahn

The Anitapolis alkaline massif in southern Brazil underlies a sub circular area of 6 km2. Bore-hole data show a concentric rock distribution, with mafic rocks in the central part and felsic rocks in the border zone. The rocks are covered by talus and weathered material, 30 m thick on average, and very inhomogeneous in composition. Phosphate mineralization associated mainly with two levels of the weathering mantle and with fresh rocks. A preliminary ore-type classification was based on distribution of apatite, feldspar, vermiculite, biotite-phiogopite, calcite, pyroxene, amphibole and analcime, determined by semiquantitative diffraction method. Technological tests performed on eluvial ore samples from three adits resulted in a subdivision of ore-types based on the difference in behavior due to mineral characteristics during mineral pr

Jan 1, 1991

By Sevinc Yildirim, Cigdem Oruclus

"Metal-Porous Silicon (PS) based structures dipped in water show the direct hydrogen fuel cell behavior. The effect of the thickness of the cupper (Cu) film on the electrical properties of direct hydrogen fuel cell is studied by fabricating Cu/Porous Silicon/n-Silicon/Indium structures. PS samples were produced electrochemical etching of n-type single crystalline silicon with a resistivity of 1,25 Ocm and (111) orientation. The thin films of Cu with different thickness between 200 and 600 nm were deposited on PS surface by electron-beam technique. Investigation of the effect of Cu layer on the performance of the structure indicates that the performance parameters such as open circuit voltage (Voc) and short circuit current (Isc) strongly depend on the Cu layer thickness. It was observed that the divice with an 350 nm Cu layer exhibits the highest open circuit voltage (0,5 V), short circuit current (0,01 mA) and power density (10 W.m-2).IntroductionHydrogen is the most attractive and ultimate candidate for a future fuel and an energy carrier. Hydrogen is recognized as the environmentally desirable clean fuel of the future since it can be used directly in different types of hydrogen fuel cells [1]. In the past years, the rise in portable electronics requires the development of miniature fuel cells compatible with standard silicon micro fabrication technology. Most silicon micro-fuel cells have used the polyperfluo-rosulfonic acid membranes (Nafion R) as a proton exchange membranes (PEM) that is not really integrated with standard micro fabrication techniques [2-5]. The composite materials such as inorganicorganic hybrid materials (Nafion-silica, Nafion-borosiloxane etc) are next generation of proton conducting membrane [4-8]. But, fuel cells run on pure hydrogen gas, which can be produced with other energy resources. Hydrogen smallest atom and thus the H2 gas can leak easiliy. The application of hydrogen for power sources has been greatly restrained due to the lack of safe and convenient generation and storage methods.A kind of hydrogen fuel cells Metal-PS-Si structures used as an energy water directly. There is no need pure hydrogen. Cu-PS-Si Schottky-type fuel cells with as proton-conducting membrane and the thin-film cupper catalist and water as fuel, which are interesting for fabrication of lowcost miniature fuel cells. Generation of the open-circuit voltage and short-circuit current has been observed by Cu-PS-Si structure dipping in different hydrogen-containing solution."

Jan 1, 2014

By Baozhong Ma, Yonglu Zhang, Yongqiang Yang, Chengyan Wang, Yongqiang Chen

During the past decades, slurry electrolysis (SE) has been implemented commercially for the processing of bismuthinite and complex Pb-Cu bearing gold concentrates. Recently, SE was proven effective for the treatment of As-rich antimonic gold concentrates. Laboratory test results suggest over 98% of the antimony was extracted, while the extraction of arsenic and gold was less than 0.5%, and that of iron was less than 6%. Moreover, the cathode antimony contained over 98% antimony and less than 0.3% arsenic. Considering the disadvantages of traditional 3 kA slurry electrolysis baths, such as smaller electrode area, reduced capacity, and greater electrode deterioration, the authors have developed an innovative 12 kA slurry electrolysis bath equipped with mesh and fence type titanium alloy electrodes. Furthermore, the technique was successfully used within a pilot scale plant yielding results similar to those observed in the laboratory. The technique yielded ametallic antimony ingot of 99.9% purity after arsenic removal via the addition of Na2CO3.

Jan 1, 2014

By Kuniaki Murase, Tetsuji Hirato, Yasuhiro Awakura

"Electrodeposition of CdTe was studied using aqueous ammonia-alkaline electrolytic baths in which Cd11-and Te1V-ions are dissolving as Cd11(NH3)/+ and Te1vol-ions, respectively. Ca-thodic polarization curves of the baths suggest the presence of strong interaction between the Cd11-and Te1V-ions; electrodeposition of tellurium is inhibited by the presence of Cd(NH3)/+ ions. The interaction makes it possible to electrodeposit CdTe films with stoichiometric composition. Polycrystalline CdTe thin film of about 1 µm thickness was electrodeposited at 343 K from ammonia-alkaline solutions (pH= 10.7) containing TeO32-(<20 mmol dm-3) and Cd(NH3)/+ ( < 60 mmol dm-3) ions. Increasing Cd(NH3)/42+/TeO32- mole ratio or decreasing total concentration of ammonia/ammonium-ion gave flat and smooth crystalline CdTe deposits at constant cathode potential-0.70 to -0.30 V vs SHE at 343 K.IntroductionCadmium telluride (CdTe) is well-known as a compound semiconductor whose band gap, i.e. 1.44 eV, is suitable for solar energy conversion with a photovoltaic cell. Various methods, such as CVD (chemical vapor deposition) and electrodeposition, of preparing CdTe thin films for solar cells have been investigated.Acidic sulfate solutions with a pH of 1-2 are usually employed for CdTe processing by electrodeposition.1-3) The electrodeposition of compound semiconductors is usually achieved (i) at a higher cathode potential than the redox potential of less-noble species, can in this case, and (ii) under the condition of diffusion-limiting current of a more noble species, Te1Y.4) There-fore, a suitable CdII/TeIV concentration ratio in the acidic electrolytic baths, resulting in the deposition of stoichiometric CdTe, is determined by the diffusion-limiting current density of TeIV- reduction, i.e. the concentration of HTeIVO2+ · Since the solubility ofTe1v species HTeIVO2+ in the acidic solutions is quite low, the rate at which CdTe is deposited from the acidic solutions is extremely slow."

Jan 1, 1998

By D. Y. Wang, G. Y. Sha, X. L. Shen, D. R. Gu

The study of the volatilization kinetics of zinc and lead in pellets made of zinc-leadbearing dust mixed with coal powder, in a nitrogen atmosphere and at a temperature range between 1100 °C and 1300 °C, shows that the reduction temperature has a significant effect on the volatilization rates of zinc and lead, and that both the particle size of the coal powder and the extra carbon content has no effect on the volatilization rates. The obtained activation energies for the volatilization of zinc and lead are 79.42kJ/mol and 88.74kJ/mol respectively. The volatilization rate of zinc is controlled by the reaction between the zinc oxide and carbon monoxide while that of lead is controlled by the lead evaporation reaction, and the diffusion of gaseous lead through the gas boundary layer covering the surface of the reduced liquid lead.

Jan 1, 2000

By Guangshi Li, Xionggang Lu, Xueliang Xie, Xingli Zou, Yuyang Bian, Hongwei Cheng, Kai Zheng, Changyuan Lu

The corrosion resistance and corroded microstructure of MgO-C refractory in molten slag are investigated by immersion test in muffle furnace at 1600 °C . The microstructure and chemical compositions of the specimens after erosion experiment are characterized by scanning electron microscope (SEM) and energy dispersive X-ray (EDX). The results confirm that the oxidation of graphite is the most important degradation mode of MgO-C refractory. The structure of the refractory material is damaged due to the decrease of graphite, as a result, the periclase substrate reacts with the molten slag directly. The corrosion process is controlled by the dissolution of the refractory materials into slag, low melting point oxides are therefore generated which lead to the damage of MgO-C refractory finally.

Jan 1, 2015

By B. Q. Li, R. A. Mirshams

"A numerical algorithm is described for the simultaneous prediction of the thermomechanical behavior of the materials and microstructure evolption during metal forging. The numerical development is based on the finite element solution of the thermoviscoplastic deformation of metals coupled with the internal state variable model describing the microstructure evolution involving work hardening, recovery, recrystallization and grain size distribution. The finite element code for rigid viscoplastic deformation is developed based on the modification of the existing code for the thermal and fluid flow calculations. The code is tested against and compares well with the results reported in literature. The procedures for the integration of the · rnicrostructure model into the macro finite element model are described. Results are presented showing the characteristics of materials dynamics and mechanical deformation during simple metal forging processes.IntroductionIn industrial deformation processes such as hot rolling and forging, the workpiece undergoes both macroscopic plastic deformations and microstructural evolution. A computer model that allows to predict both materials dynamics and macroscopic deformation is obviously more useful for both fundamental understanding and deformation process optimization. For some industrial applications, especially those involving novel, light and high strength materials, such an integrated model is critical in that both materials and thermomechanical 'behavior during forging must be carefully controlled to obtain the products that meet the desired strength requirement [I]."

Jan 1, 2000

By P. Gray

Process and engineering development of the Warner Zinc Process over the past two decades has proceeded alongside the world-wide collection and analysis of operating and cost data of current processing practices from sulphide ores to refined metals. Study of these data shows that recoveries are dependent on mineralogical characteristics of the sulphide matrix and point to the inadequacy of differential flotation as a tool for preparing feed for smelters. The paid-for return at the mine on the combined metal values in zinc rich sulphide ores rarely exceeds 80% and increasingly runs as low as 50-60%. Surveying the possible alternative ways of improving these performances leads to the conclusion that the Warner Process is the only technology in sight that could meet a target of 90% paid-for recovery and that its development has now reached a point where it can be a fully practicable process for all mixed sulphide ores.

Jan 1, 2000

By L. J. Cabri

The level of mineral exploration activity for platinum in recent years, especially in North America, has ranged widely. Exploration programs have been based on a variety of ore deposit models and deposit types. These range from the classic magmatic model for sulfide/oxide deposits and their associated placers, through hydrothennal models for bonanza-type deposits, to low-grade mineralization potentially amenable to lower cost bulk mining methods. The platinum-group element (PGE) distribution in these different deposit types is not well-known however, and PGE determination is fraught with analytical difficulties. To properly assess a prospect or to achieve effective recovery by mineral processing, it is important to determine the mineralogical distribution of the PGE.

Jan 1, 1988

By Hong Ro Lee, Seang Suk Cho, Byung Sun Chun, Chang Whan Won

"The preparation of Al203-SiC-TiC composite powders was studied by SHS process using silica (source of Si02) powder instead of Si which is expensive. And, aluminum powder was used as reducing agent of silica and charcoal activated was used as carbon source. Effects of the molar ratio in raw material mixtures and compaction pressure and initial temperature of reactant on the products and combustion process were studied. The most important variable affecting the synthesis of Al203-SiC-TiC was the molar ratio of carbon. The combustion reaction generated in powder state without preheating. But the unreactants exist in the product on all molar ratio. When the preheating temperature is over 400 °C, the combustion reaction was able to be generated in pellet state. Without preheating, the combustion reaction was possible by Ti02 addition. The optimum condition in this system was the molar ratio of Si02:Ti02:Al:C=2.5:0.5:4:3.1. INTRODUCTIONCeramics have demonstrated a capability as a cutting tool, especially in competition with WC-Co cermets (ceramic-metal composites) as inserts for metal turning and milling operation. The advantage of ceramics compared with carbides is retention of high hardness, strength, and chemical inertness to temperatures in excess of 1000 ·c . This allows use of the ceramics at much higher machining speeds than can be tolerated by carbides. However, the ceramics have lower toughness than the carbide materials, and have only been used successfully in the limited operations of turning and milling. There are several classes of cutting tools. The addition of TiC or PSZ, or both, and reinforcement with SiC overcame the poor fracture toughness and thermal-shock resistance that limited Al203 use in the past [1]."

Jan 1, 1998

By S. Viswanathan, A. S. Sabau

"Dimensional changes between a pattern die and its corresponding investment casting part occur as a result of complex phenomena such as thermal expansion/contraction and hot deformation (elastic, plastic, and creep) during the processing of the pattern material (wax), mold material (shell) and solidifying alloy. Determining the pattern tooling dimensions is crucial to the dimensional control of the investment casting process. To date, computational methodologies have not been applied to the prediction of dimensional changes in investment castings.This paper deals with the evaluation of wax pattern dimensions, which is one important factor in determining pattern tooling dimensions in investment casting. Cerita 29-51, an industrial wax, is considered in this study. The wax pattern dimensions are determined by considering its thermo physical and thermomechanical properties, restraint of geometrical features by the metal die, and process parameters such as dwell time, platen temperature, injection pressure, and injection temperature.IntroductionThe investment casting process involves making a disposable wax pattern by injecting wax into a metal mold, building a ceramic shell mold around the wax pattern by the application of a series of ceramic coatings to the wax pattern, dewaxing the ceramic shell mold, and casting the alloy into the shell mold. Dimensional changes between the pattern tooling and its corresponding cast part occur as a result of thermal expansion, shrinkage, hot deformation, and creep of the pattern .material (wax), mold material (shell), and solidifying alloy during the processing [1]."

Jan 1, 2001

By L. Lewczuk

A detailed mineralogical and liberation study was performed on the iron ore mill products from the Scully concentrator of Wabush Mines, Newfoundland. Automated image analysis techniques were applied to deter-mine grain size distribution and liberation of all mineral components of the ore. As a result of the study it was indicated that iron recovery can be improved and the Mn minerals reduced in the iron ore concentrate by (a) increasing spiral middlings, (b) regrinding the middlings, and (c) separating the Mn minerals from the iron minerals in the reground middlings.

Jan 1, 1988

By G. L. Watt

Fine sized titanium diboride (TiB2) powders have been synthesized in a thermal plasma reactor. Precursor for the synthesis were rutile, boron oxide, and methane. The effect of plasma gas type, precursor ratio, and input power on the synthesis was studied. The produced powders were characterized by X-ray diffraction and chemical analysis. The purified powders were CIP&apos;d, HIP&apos;d, sintered and characterized for porosity, hardness, and microstructure and the results compared with a commercially available TiB2 powder sample.

Jan 1, 1995

By Xu Weimin

The existing copper electrorefining tankhouse of Jinchuan Nonferrous Metals Complex (JNC) was commissioned in 1986 for refining blister copper anodes. Blister copper is produced by reverberating chalcocite separated from converter high grade nickel-copper matter by means of flotation. Special chemical analysis of the anodes shows, a composition of 93.02 - 95.72 % copper, 3.0 - 4.96 % nickel and 0.5 - 1.23 % sulfur. The wide range of composition makes the electrorefining process fairly different from others throughout the world. The initial nickel content of 20 ppm and sulfur 40 ppm or more in copper cathodes are reduced to 8.5 ppm and 11 ppm respectively. Since 1986 the tankhouse has undergone significant evolutionary modifications and implementations to ameliorate cathodes quality desirably. The important fact is that the N-additive was utilized through many studies and pilot and field trials successfully. While our primary purpose is to improve chemical quality of the cathodes, tankhouse capacity is increased considerably and the process is perfected satisfactorily. The tankhouse is described with special emphasis on JINCHUAN PROCESS. The upgrading of our product by the utilization of the N-additive is highlighted. The other aspects of the tankhouse including spent electrolyte treatment and by product nickel sulfate manufacturing are briefed as well. Key words: JINCHUAN PROCESS, anode, cathode, electrolyte, electrorefining, N-additive.

Jan 1, 1993

By D. Lambert

Process modeling for large deformation metal forming processes has been developed into a very successful tool in commercial applications during the last two decades. DEFOR.MTM is a well-known metal forming process simulation program used by many industrial and research institutions. Recent developments include the ability to model multiple deforming body behavior during multi-pass pack rolling and microstructure prediction during multi-pass shape rolling. This paper summarizes how DEFOR.MTM can be applied to a number of rolling processes and briefly describes preliminary work carried out using the ALE technique. Keywords: Simulation, Rolling, Pack, Shape, Microstructure, FEM, ALE, Tantalum

Jan 1, 2003

By Jacques Magnaudet, Julie Cranga, Didier Huin, Pascal Gardin

"With the aim of controlling steel grade in steelmaking reactors, IRSID and IMFT are developing a numerical description of the evolution of bubbles in the vicinity of a liquid steel/ slag interface. The objective is to identify the main parameters affecting the hydrodynamics of the various phases. The goals of the present paper are:• To describe the numerical technique developed to predict the multi phase flow including bubbles, liquid metal and slag layer.• To analyze the influence of the absolute pressure on the bursting of bubbles in a RH degasser. Validation is given by comparison with results available in the literature. The major point concerns the distinct behaviors observed whether the pressure is low or high.• To study the influence of the properties of the slag layer (thickness, viscosity and interfacial tension) on the entrainment of liquid metal in the wake of the bubble and on the nature of the projections from the bath surface.IntroductionMost of secondary steelmaking processes use gas stirring for homogenization, removal of nonmetallic inclusions or decarburization under reduced pressure. The bursting of gas bubbles at the metal or slag layer surface produces a beneficial ejection of metal droplets in the low pressure atmosphere, provided that there is no violent projection, which may have detrimental effects on the process.Our objective is to develop a numerical tool to study the phenomena occurring in the vicinity of the bath surface, in particular bubble bursting under reduced pressure and entrainment of metal in the slag layer. In this paper we report the first conclusions of our study. In the first section we describe the numerical model used to describe the three-phase flow and the expansion of the gas bubbles under the effect of the ferrostatic pressure. The second section is devoted to the study of pressure effects on bubble rise and bursting. The third section reports some computational results about the rise of a gas bubble through the interface between the two liquids."

Jan 1, 2001

By Lori Bassman, Cassandra George, Cullen McMahon, Md. Zakaria Quadir, Michael Ferry

"Complete and accurate analysis of subgrain microstructural features must include three-dimensional information. Three-dimensional electron backscatter diffraction (EBSD) data can be used to characterize these features; however their boundaries first must be determined. This cannot be accomplished simply with pixel-to-pixel misorientation thresholding because many of the boundaries are gradual transitions in crystallographic orientation. Fast Multiscale Clustering (FMC) is an established image processing technique that we have combined with quaternion representation of orientation to segment this kind of data. Segmentation algorithms often have issues handling images with both distinct and subtle boundaries. Our implementation of FMC addresses this by using a novel distance function and statistical analysis to take into account the variance in orientation of each feature. Although FMC was originally a twodimensional image processing algorithm it can be generalized to analyze threedimensional data sets. As an example, a segmentation of microbands in cold-rolled aluminum is presented.IntroductionThree-dimensional electron backscatter diffraction (3D-EBSD) is a method for mapping the local crystallographic orientations of points in a volume. The technique uses a dual beam platform consisting of a focused ion beam (FIB) and SEM with EBSD, where FIB is used for serial sectioning and EBSD for orientation mapping of 2D slices. These 2D slices may then be stacked to create a 3D volumetric data set.Typical uses of such a data set include characterizing the geometries and crystallographic orientations of surfaces between structures in 3D [1-5]. This involves identifying boundaries accurately, either in 2D slices with subsequent 3D reconstruction (as illustrated in Figure 1) or in the 3D data set. All such data sets present the challenges of i) aligning data slices to correct for instrument drift, ii) identifying relevant boundaries, and iii) implementing appropriate smoothing or interpolation algorithms. The focus of this paper is boundary identification."

Jan 1, 2011

By James W. Evans, Brian R. Wildey

"Carbon has been the principal reducing agent in producing metals for centuries. Carbon is an inexpensive reducing agent, but also an effective one, as any undergraduate who knows her Ellingham diagrams is aware. Even in the production of aluminum, an electrolytic process, carbon consumed at the anodes serves to reduce the voltage of the Hall-Héroult cell. The interest in reducing the amount of anthropogenic CO2 has led to this examination of whether a switch to hydrogen as a major reductant is feasible and economic. The main source of hydrogen is natural gas and its production entails the generation of CO2; however, that CO2 is more easily captured than, say, the CO2 leaving an iron blast furnace. Calculations and speculations lead to conclusions about whether there is significant benefit to be obtained from such a radical change in our way of producing metals and the approximate cost of such change.IntroductionThe 1991 paper by Forrest and Szekely1 was one of the first to examine the impact of CO2 emissions from the primary metals industries on global climate change. These authors compared data from 1968 and 1985 and reported a drop in carbon emissions from 115.8 million tons to 65.6Mt over this period, the latter figure representing approximately 1% of the world’s greenhouse gas emissions. Much of this reduction was due to a drop in steel output (with carbon emissions increasing within the aluminum and copper industries in this period) but some were due to technological changes such as increased use of continuous casting. A more recent paper on CO2 emissions, focused on the steel industry in Japan, is that of Ariyama and Sato2. These authors report CO2 emissions of 182.4Mt from the Japanese steel, industry in 2003, down from 194.8Mt in 1990. The former represents 14% of the GHG emissions for Japan in 2003. Much of this emission is from ironmaking and the authors break these emissions down into"

Jan 1, 2008

By Nathalie Neveux

For the first time, dehydrated ferrous sulfate was successfully used for the dry synthesis of potassium ferrate. In addition, ferrate ion is stabilized as a solid solution where hexavalent iron is partially substituted by S(V1) leading to a sulfato-ferrate having the following formula K2(Fe,S)04. This substance has an efficient life time of about six months. Ferrate ion is a powerful oxidant ( EO = 2.2V ), a bactericidal agent and possesses coagulant, flocculant properties. Its reduction generates nascent oxygen, hydroxyl groups and Fe(OH)3. Alkali metal ferrate is probably the future global agent for water treatment. Applications of this material in the field of urban and industrial effluents treatment have been investigated. Heavy metals cations such as Cu, Cd, Mn, Ni, Pb, Zn, ... were successfully removed. The results of sulfato-ferrate use for cyanide destruction, decrease in COD, soil, discoloration of pulp and paper effluents will be summarized.

Jan 1, 1999