Search Documents

By H. Fayed

Two-phase (water and air) flow in a self-aspirated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). The geometric model is a replica of a 300 m3 cell. A 72-degree sector containing two blades of the ten-blade rotor has been modeled and periodic boundary conditions are applied in the circumferential direction. Simulation of a sector of the machine allows acceptable resolution of the mean flow field using 4x106 grid points. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Unsteady simulations have been performed. In a self-aspirated machine, airflow rate is not known a prior; it is an output from the CFD simulation. Uniform mean bubble diameter of 0.7 mm has been specified as an input for the simulation. Air flow rate and power consumption have been monitored with time, and results indicate a stable operation. Air volume fraction contours and velocity field in different regions of the machine are presented and discussed.

Feb 27, 2013

By R. C. Berry

The Environmental Impact Statement (EIS) has become a routine requirement for mining operations on federal lands. A similar document is being required in developing countries. Baseline studies are needed prior to writing an EIS and these studies involve surface water, groundwater, air quality, and wildlife/ native plant evaluations. The required baseline hydrology and geochemical studies are often the most expensive and lengthy evaluations. This paper summarizes the hydrology and geochemical baseline studies required for .An EIS and presents suggested methods to expedite these studies and to shorten the time and the cost to complete the studies and the EIS.

Jan 1, 1999

By N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities during 2017 draws upon information from industry sources, published literature, SNL Metals & Mining (SNL), an offering of S&P Global Market Intelligence (New York, NY) and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. Three types of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. dollars provided by SNL; 2) regional and site-specific exploration activities that took place in 2017 as compiled by the USGS and 3) regional events and legislation that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources were used to develop commodity and regional compilations, statistics may vary depending on the source and type of data that are being reported.The SNL data summarize budget estimates for worldwide exploration activities in 2017 for 30 nonfuel mineral commodities and metal alloys, based on company surveys. Surveys focused on precious metals (gold, platinumgroup metals (PGMs) and silver), base metals (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (bauxite, chromite, iron ore, manganese, phosphate and potash), and other commodities (aluminum, antimony, diamond, graphite, heavy-mineral sands, lithium, niobium, rare-earth elements (REEs), scandium, tantalum, tungsten, uranium, vanadium and yttrium). Information on uranium exploration activities was included in SNL’s survey for the first time in 2007. Data on lithium, niobium, phosphate, potash, REE and tungsten were compiled for the first time in 2010, and scandium, vanadium and yttrium were added in 2014 because of their increased topical significance. Since 1999, companies with exploration budgets of $100,000 and greater were included in the SNL surveys. SNL budget estimates exclude coal, and oil and gas. The 2017 SNL mining company survey compilation was reported by SNL to include an estimated 95 percent of the world’s nonfuel mineral exploration budgets. The 5 percent that was not covered was accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data, and government-funded exploration activities."

Jan 5, 2018

By Josh Willhite, Seth Pollak, Ben Seling

The Long Baseline Neutrino Facility Far Site at the Sanford Underground Research Facility in Lead, South Dakota will house four large detector tanks located in deep underground caverns. Construction of the supporting infrastructure required for this project is no complete including installation of a waste rock conveyance system and drill and blast excavation of several supporting drifts and chambers. This paper will discuss the design and construction of these pre-excavation and early works elements, and the overall project schedule as it closes in on commencement of cavern excavation activities.

Jun 13, 2021

By P. Somasundaran

Three major types of solution chemical equilibria involving flotagents (Le. flotation reagents such as collectors, frothers and modifiers), minerals and solution play a crucial role in determining the behavior of complex flotation systems. Minerals of phosphates (apatite and francolite), tungsten (wolframite and scheelite) and associated carbonates (calcite and dolomite) are sparingly soluble in aqueous solution and form dissolved mineral species in bulk solution. Such dissolved species interact with mineral solids, often resulting in surface conversion of the minerals. In addition, they can interact with various flotagents and lead to surface or bulk precipitation and loss of selectivity in the flotation. Relevant solution equilibria of such sparingly soluble minerals and their interactions with oleic acid and structurally modified reagents were determined in this study using a multi-pronged experimental approach. Methods to manipulate and control the solution chemical equilibria and thus achieve selectivity in flotation systems are discussed.

Jan 1, 1990

By D. H. Lynch

This paper is a general description of current Central Florida phosphate mining, beneficiation and product transportation. It is directed and believed to be of interest to engineers not familiar with this industry.

Jan 1, 1978

"The National Mining Hall of Fame and Museum (NMHF&M) announced the 2015 National Mining Hall of Fame inductees and the 2015 Prazen Award winner. This year’s inductees, selected by the National Mining Hall of Fame’s Board of Governors, represent the technology, management, mineral policy, education and health and safety aspects of the mining industry. They envelope a diverse cross section of the mining industry and were selected for being visionaries, leaders, educators and ambassadors.In 2015, Frank F. Aplan, T S Ary, Ralph E. Bailey, John Campbell Greenway and Edward Steidle will join 227 other mining industry honorees when formally inducted into the National Mining Hall of Fame. The Prazen Living Legend of Mining Award will go to the Powell River Project Research and Education Center, a partnership of Virginia Polytechnic Institute and State University (Virginia Tech) and the Appalachian coal mining industry.The 2015 annual induction banquet and ceremony will be the 28th such event and will be held this year in Pittsburgh, PA, on Oct. 23, 2015, in the Omni William Penn Hotel ballroom.2015 National Mining Hall of Fame inductees:Frank F. Aplan is among the most influential mineral processing leaders in both industry and academia. His studies of the processes involved in the preparation of coal and mineral ores are acknowledged worldwide for their broad applicability. An authority on flotation, Aplan is especially known for his studies of the wetting of solids and their control through the adsorption of surfactant films, and for his work on atomic defects on properties and behavior of solid-liquid interfaces."

Jan 1, 2015

By S. Que

Local community acceptance is a key aspect of planning and managing mining projects, whether through sustainability assessment and reporting or corporate social responsibility programs. However, there has been very little research to understand the determinants of community acceptance. This paper seeks to identify key mine characteristics and demographic factors that influence individual acceptance of mining projects. Six demographic factors and 16 mine characteristics were selected based on literature review. Four of the six demographics factors were confirmed to be significantly (p < 0.05) correlated with people?s attitude of the importance of the mine characteristics. All sixteen mine characteristics are identified as important factors. The most important mining factors are Job opportunities, water shortage or pollution, air pollution and land pollution. Both the mining and control groups have same opinion of 12 mining characteristics and differ on four (infrastructure improvement, labor shortage for other businesses, noise pollution, and mine life). During design and management of mines, this data can be used as a reference. This result will facilitate better choice experiment (survey) design for discrete choice modeling. Such discrete choice models can provide a viable framework for data-driven community engagement and sustainable mine management.

Feb 23, 2014

By Weiguo Xie, MARK LAPUTKA

The pyrometallurgical industry plays a vital role in producing metals for our modern life. With growing demand of metals and declining grade of mineable ore, innovations become critical for many mining companies. It is necessary to conduct a review of recent improvements to the pyrometallurgical industry on analytical measurement techniques, process and equipment improvements, and computer-based modeling/simulations. Many of those innovations tend to be applied to wider metals, and not be restricted by a specific metal. Therefore, we tried to cover the wide applications of many improvements to wider range of metals to reflect this trend. The challenge of a lack of robust measurement techniques under high-temperature conditions within a furnace hinders optimization of a pyrometallurgical process. Some future opportunities in the pyrometallurgical industry on analytical measurement techniques, computer modeling, and processes and equipment have also been outlined and discussed.

Jan 26, 2021

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998

By Kraig W. Grubaugh

Rapid growth in the rate of surface mining for coal has caused many states to increase the rigor and complexity of their surface mining codes. The promulgation of Federal surface mining standards may cause those states containing Federal land to amend their codes also. Presented is an up-to-date review of these codes with tabular summaries that divide the codes into operative functions. These summaries will be of use to new operators, multiple-state operators, and state officials. Suggestions are made for industrial efforts to present workable and acceptable amendments to these codes.

Jan 1, 1977

By Terrence Chatwin, Michael Sweeney, Steve Accardo

Sutter Gold Venture excavated an exploration decline into a mineralized zone in the Sutter Creek gold mining district. Delays in obtaining the conditional-use permit resulted in 7 to 10 million gallons of water accumulation in the decline containing elevated dissolved arsenic. Sutter received a permit to land apply the water after reducing the arsenic concentration to 0.05 mg/L. Initially the water was treated by co- precipitation arsenic with ferric hydroxide. Operational difficulties of this treatment system resulted in Sutter pursuing alternative treatment methods. The activated alumina adsorpting was selected due to its flexibility and ease of operation. Operating and maintenance data and costs will be presented.

Jan 1, 1995

By L. C. Lang

INTRODUCTION The introduction of 165-mm (61/z-in.) holes to underground mining operations has made possible the application of Canadian Industries Ltd&apos;s (CIL) vertical crater retreat (VCR) mining method, illustrated in the accompanying sketches. This unique and revolutionary new application of spherical charge technology (see the Appendix), when applied to primary stopes and pillar recovery, eliminates raise boring, slot cutting, and dilu¬tion of ore by backfill; greatly improves fragmentation; reduces labor and time requirements; eliminates uphole drilling and blasting; and minimizes or completely elimi¬nates damages by blasts to the walls and retreating backs of the stope or pillar. If vertical large diameter holes are drilled on a designed pattern from a cut over a stope or pillar to bottom in the back of the undercut, and spherical charges of explosives are placed within these holes at the calculated optimum distance from the back of the undercut and detonated, a vertical thickness of ore will be blasted downwards into the previously mined area. Repeating this loading and blasting procedure, min¬ing of the stope or pillar retreats in the form of horizontal slices in a vertical upwards direction until the top sill is blasted and the mining of a stope or pillar is completed. The VCR method is also applicable to drop raises and has the potential to replace all other raising methods under most circumstances. PILLAR RECOVERY Levack Mine Inco Metals Co., Ontario Div., provided the first opportunity for the method in pillar recovery. The Levack mine&apos;s high grade ore pillar No. 4800 on the 975-m (3200-ft) level was used for the production¬scale experiment (Figs. 1 to 3). The pillar was about 49 m (160 ft) long, 6 m (20 ft) wide, and 20 to 26 m (65 to 85 ft) high. The mined area on both sides of the pillar was backfilled with a 1:30 cement:sand mixture. The pillar was removed in two phases. In phase 1, the standard uphole method was used to blast down the 18-m (60-ft) long section of waste from the bottom of the ore into the undercut. From the pillar&apos;s top sill, 165-mm (61/a-in.) holes were drilled downward into the pillar, and by measuring the depth of the holes, the results of the uphole blast were determined and roof line 1 was established. The bottom of each hole was plugged, then filled with sand to place the center of gravity of each spherical charge (loaded from the top sill) at a predetermined optimum distance from the horizontal free surface. The charges were then detonated. After detonation, both draw drifts were full of extremely well-broken material. The depth of each hole was measured again, and the plot of these depths re¬sulted in roof line 2. The same blasting procedure was repeated and the resultant new back elevation was marked by roof line 3. The poor results of the initial uphole blast at one location (notice the peak in area 1) appeared to influ¬ence the subsequent new backs. A third blast success¬fully evened the back, and resulted in roof line 4. An unblasted slab averaging 6.3 m (20.9 ft) thick remained below the pillar&apos;s top elevation as the final sill. In all three spherical charge blasts fragmentation of the blasted material was extremely fine. The backfill was fully exposed on both sides of the now-blasted pillar. The backfill remained undamaged and the ore was not diluted by sand. The remnants of all the 165-mm (61/2 -in.) holes remained clean and undamaged, and the holes had well-defined bottoms that could be easily measured and plugged. Each blast took down a 3.9 to 4.2-m (13 to 14-ft) thick horizontal slab of ore. Productivity was three times greater than that of the previously practiced cut-and-fill method. Since this was the first such experiment, blasting the remaining 6-m (20-ft) thick final slab was the sub¬ject of some deliberation. If the described method was repeated, we could have ended up with a 1.8-m (6-ft) thick sill unsafe to work on. It was therefore decided to blast the whole sill using two spherical charges prop¬erly placed in each hole, but with the application of

Jan 1, 1982

By J. W. Breen

ASARCO Incorporated has upgraded or is in the process of upgrading the Galena mine electrical, pumping, refrigeration, compressed air, ventilation, hoisting and rockburst monitoring systems to allow continued mining and development work on the 1 589-m (5,200-ft.) level and to provide services for projected deeper mining and development. Additionally, a separate lead-silver milling circuit has been added to the silver-copper mill to process lead-silver ore reserves. This paper describes completed and planned improvements made to date on these systems.

Jan 1, 1991

By Kanhaiya Mishra, Phanil. K. Mandal, S. K. Behera, P. S. Paul, Prashant Singh, C. N. Ghosh

The techno-economic and social benefits of cemented paste backfill (CPB) resulted in its wide acceptance by the mining industry. The Ordinary Portland Cement (OPC) remains the key binder but to diminish its economical constraints, suitability of alternate binders has been examined worldwide. The present study aimed to investigate the effect of partial replacement of OPC with fly ash on the CPB’s strength and to determine the most optimal mix to achieve the required strength (1 MPa at 28 days of curing) at the most cost-effective way using the Bayesian network (BN). The CPB mixes were prepared at 72 wt.% solid concentration with mill tailings (87–91%), OPC (6–13%), and fly ash (0–4%), and instantly after mixing, fresh (slump, bleeding, density) CPB properties were measured. The strength was tested at 7, 14, 28, and 56 days of curing and initially analysed through traditional model. The traditional models follow the aleatory principle and are considered not appropriate for geotechnical engineering. Hence, the BN model was developed and tested. The reliability of two classifiers in learning model structure was compared which gives Naïve Bayes as the highest reliable tool. The CPB’s strength is most sensitive to the OPC content. The most consistent mix(s) is mill tailings: 87–88%, OPC: 9–11%, fly ash: 1–4%. Adding fly ash at 89–91wt% mill tailings possesses high failure probability of the CPB. The collinearity test indicates that the fines percentage and chemical composition of CPB’s ingredients are highly correlated with its slump, bleeding, and strength development.

Jul 14, 2022

By John R. Bogert

The title of this session is "Wall Street Looks at the Mining Industry," and I am going to attempt to answer the question: Shouldn&apos;t Mining Stocks Sell at Higher Price Levels? Or, What Does Wall Street See When Looking at the Mining Industry? Well, it sees a capital intensive business, a technical industry, and a growing industry becoming more vertically integrated. But, at the same time, Wall Street sees a cyclical industry, a fragmented industry of erratic earnings, spotty public relations, a feast-or-famine business where the public usually does not differentiate between coal mining or metal mining, and does not appreciate either the risks or the rewards. As a result, mining stocks generally sell at relatively low price learnings ratios in comparison to other industrial groups. This PIE ratio, the current market price of the capital stock divided by annual earnings per share, is probably the most popular index of a stock&apos;s value. The average of the price/ earnings ratios of the 30 stocks comprising the Dow Jones Industrial Average is over 14. This diverse group of stocks is widely regarded as being a cross-section and representative of the industrial companies listed on the New York Stock Exchange. However, in comparison to 14, Asarco and Kennecott shares are currently available for about 8 times annual earnings. Even discounting earnings from South America, the stock of these two companies sells at only 10 times earnings. Of course, Peruvian politics is currently preventing Cerro shares from selling above 6 times earnings, and Chilean politics keeps Anaconda shares at a PIE multiple of 7. However, even in better times, these companies rarely sell above 10 times earnings. American Metal Climax and Newmont sell at only 11 times earnings as does Phelps Dodge and St. Joseph Lead. Few mining companies then have what can be considered a high PIE ratio-a figure higher than

Jan 1, 1970

By N. K. Dumakor-Dupey, K. J. Bansah

"We made site visits to determine potential environmental issues caused by artisanal and small-scale mining (ASM) in the Tarkwa Mining Area (TMA) of Ghana. Activities of the diggers were observed to degrade vegetation, land and water. Improper handling of mercury was also identified as a major threat to people and ecosystem. Large abandoned pits and trenches posed fall traps to farmers, hunters and wildlife. We argue that lack of adequate monitoring and regulatory enforcement by Ghanaian authorities, together with inappropriate mining processes, probably due to lack of technical expertise are contributing factors to the environmental issues of artisanal and small-scale mining in the TMA. INTRODUCTION Environmental degradation caused by artisanal and small-scale mining (ASM) has been a major concern to many people and governments around the world. ASM is often associated with health, safety and environmental issues in communities where it is practiced (Kitula, 2006; Asiedu, 2013; Sousa et al., 2010). Some of the environmental issues that have been reported include land degradation, mercury contamination, cyanide release, and pollution of rivers/streams. These issues have been attributed to improper mining methods, inefficient technology, lack of technical training and environmental awareness, and lack of regulatory enforcement (Serfor-Armah et al., 2005; Bansah et al., 2016a; Hentschel et al., 2002). In Ghana, ASM typically occurs in rural communities, providing jobs to many people and contributing towards socioeconomic growth of the country (Banchirigah & Hilson, 2010; Bansah et al., 2016b; Osei-Kojo & Andrews, 2016). As a result of the environmental issues, many people have called on government to develop drastic measures to control ASM operations. It is in this regard that this paper examines potential environmental issues caused by ASM in the Tarkwa Mining Area in Ghana, and suggests mitigation measures to ensure environmental sustainability. ASM in the area comprises of registered (licensed) and unregistered (unlicensed) operations that adopt surface or underground mining methods to exploit gold-bearing materials. Surface operations typically involve clearing of vegetation, removal of overburden, excavation of mineral deposit, washing/grinding of excavated gravels and processing with mercury. Except grinding, washing and mercury recovery, underground operations are conducted below ground with limited impact on the surface. Alluvial mining is also commonly practiced in streams and along river banks. These activities can have devastating impact on biodiversity of the ecosystem. To achieve the objective for this study, field visits were made to ASM sites to observe operations and interact with diggers. Visits were also made to host communities of ASM and government officials to obtain their perspectives on ASM in relation to environmental impact. The study area (Tarkwa Mining Area) is located in the Western Region of Ghana (see Figure 1). It is endowed with natural resources such as gold and manganese. Hence, mining is the major economic activity in the area. ASM is widespread, with 15 registered operations and several unregistered mines. The environmental issues observed in the study have been grouped into three main categories: vegetation and land depletion; water quality and pollution issues; and mercury contamination issues."

Jan 1, 2017

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2009 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on industry exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities by the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2009: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia, and 2) information on regional and site-specific exploration activities that took place in 2009 and were compiled by the USGS. The MEG information summarizes planned company budgets for worldwide exploration activities in 2009, primarily for base metals (copper, lead, nickel and zinc), diamond and precious metals (gold, platinum-group metals and silver). Information on uranium exploration was included in the MEG overview for the first time in 2007, although this information was not included in the USGS analysis prior to 2008. The MEG survey methodology was changed in 1999 to include companies with exploration budgets greater than $100,000, as well as those companies included in prior studies whose anticipated budgets were above $2.9 million. MEG estimates that its post-1999 surveys cover at least 90 percent of world nonferrous nonfuel mineral exploration budgets. The 2009 survey is reported by MEG to cover an estimated 95 percent. Companies who chose not to participate in the MEG study, private companies that do not publish data and government-funded exploration activities make up the majority of the remaining 5 percent. MEG included 86 more companies in its 2009 survey than it did in 2008.

May 1, 2010

By WILLIAM M. CROSS, ALBERT ROMKES, BERNARDO MORENO BAQUEIRO SANSAO, Jon J. Kellar

In this research study, the interaction of particles with substrates of different roughness magnitude was investigated. Particle surface treatment, relative humidity (RH), and surface roughness levels were controlled in order to achieve separation of different particles by applying removal forces. Three different approaches to reproducibly roughen surfaces were used. Initially, glass disks were laser engraved to create a reproducible, controlled roughness substrate. However, the laser engraving method produced surface features that were much greater in scale than the particles. These scale differences were such that the substrates produced were not of value to this research. The second option investigated to induce reproducible substrate roughness was to scratch the glass disk using sandpapers of known grain size. A third approach to establish reproducible roughness was to use fine stainless-steel wire mesh substrates. In tests with sanded glass disks, the interfacial energy of plasma-cleaned (hydrophilic) glass beads had a high variation at 40% RH, showing non-uniformity of area of contact between particles and substrates. As the RH increased, it was expected that the interfacial energy of hydrophilic particles would increase, but this behavior was not observed. In addition, comparing the interfacial energy results of hydrophilic particles with hydrophobic particles, a region with significant interfacial energy difference was not identified. In the case of the stainless-steel mesh substrate, the mesh asperities and particle dimensions were comparable. Thus, the smaller particles had more area of contact with the substrate than the larger particles. For the plasma-cleaned (hydrophilic) beads, the recovery values had an average of 92.5% recovery when the RH was between 46 and 85%. For the hydrophobic beads, the average recovery was 19.0% when the RH was between 46 and 75%. Thus, the hydrophobic characteristic of the particle influenced its lower interaction with the mesh substrate. The difference in recovery can be exploited to achieve separation of particles based upon adhesive forces.

Nov 30, 2021

By Iwasaki I.

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates, and the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when anionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were most strongly affected by the level of starch, to a lesser degree by the pH, and were virtually independent of the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semi-taconite could be readily attained with starch and calcium chloride.

Jan 1, 1968