Search Documents

By J. Hop, A. Støre, T. Foosnæs

The carbon cathode for aluminium electrolysis is also part of the container of the process. In order to understand the behaviour and possible failure of the cathode, detailed material properties under operating conditions are needed. The paper reports experimental studies of bath and sodium in filtration, graphitization with time, loss of strength due to sodium, sodium expansion as function of pressure, as well as creep due to the developed stresses. As an example, sodium and thermal expansion data are used to calculate strain-stress models of realistic cell designs, and possible design weakness can be pointed out. Keywords: carbon, cathodes, sodium expansion, strength, graphitization, creep

Jan 1, 2004

By A. Singh

The control of flotation plants is by no means trivial. Flotation is one of the most interactive minerals? processing operations. The interactive nature of flotation circuits results in oscillations of levels and hence of grades and recoveries. Also, poor level setpoint tracking and disturbances have negative influences on grades and recoveries. The result is an unstable plant with limited scope for optimization. An advanced controller, FloatStarTM, has been developed to provide tight control and to reduce the amount of disturbances in flotation levels. It has been shown on a number of plants that the system results in faster and better setpoint tracking, better regulatory control and faster settling times after start-ups and disturbances. The successful stabilization provided by FloatStar has made it easier to investigate the area of optimization on flotation circuits. Mintek has identified the need for a more meaningful set of setpoints or aeration rates to use as a basis for control than levels and have advocated flow control by looking after residence times. When the feed conditions change, the ideal solution would be an algorithm or strategy that finds the new optimum conditions rather than just having an unguided hunt from the previous point. A multivariable flow-optimizing algorithm, a new module in FloatStar, has been developed to calculate optimum level setpoints and/or aeration rates that will aim to optimize the residence times, mass pulls and circulating loads within a flotation circuit. Keywords: flotation, regulatory, FloatStar, start-up, disturbance, residence times, circulating loads

Jan 1, 2003

By P Knight, P A. Walker, H E. Speight

Pushback 8 South is the final cut back on the south wall of the East Pit at BHPBilliton?s Mt Whaleback iron ore mine in the Pilbara region of Western Australia. Development of the cutback commenced in 1999 and is now nearing completion with ultimate pit walls up to 300m high. This paper describes the geotechnical, structural and hydrogeological setting of PB8S, reconciliation between design and slope performance and the slope engineering techniques used to effectively manage the risks associated with the slope. These techniques include slope buttressing and sequential mining with waste backfilling, as well as a detailed program of displacement and hydrogeological monitoring, structural mapping and slope stability assessment. During the course of slope formation recent developments in remote slope displacement monitoring using radar and remote structural mapping using terrestrial photogrammetry have also been applied. Aspects of the PB8S slope management plan are relevant to many large scale open pit slopes. This paper provides geotechnical practitioners with information which may be helpful in managing geotechnical risk in similar environments.

Jan 1, 2006

By A. Beitz, P. Smartt, G. Einicke, G. Rowan, P. Glynn

Coal is Australia’s highest export earner and Australia is the world’s largest exporter of coal. With coal now being extracted from deeper reserves under increased risk profile, and in the interest of aiding the stability of coal supplies, Japan is funding a number of safety projects in Australia and China. The CSIRO, Australia’s premiere research organisation with the country’s largest exploration and mining research group, are currently undertaking a jointly funded Japan-Australia safety project at Anglo Coal’s new Grasstree Colliery in central Queensland. The project, entitled Mine Communication and Information for Real-time Risk Analysis, will deliver step-change capabilities in data integration, decision support, gas monitoring, geo-technical monitoring, emergency response and personnel safety to the Grasstree Colliery. Some key activities include: developing and installing underground coal mine Ethernet LAN components, real-time monitoring of gas and geo-technical sensors, MODBUS serial to TCP/IP converters, e-reporting of underground conditions, emergency guidance systems and underground trials of Internet Protocol telephone and video. The project seeks to integrate (in real time) key data sets from the comprehensive and diversified range of propriety system currently in use at mines (ventilation, strata, operations e.g. haulage, pumps, conveyors etc) into a single integrated risk management interface. This interface will filter the data through a rules-based inference engine that will cross reference the various data streams, compare with past events and outcomes associated with the similar historical data and present this “intelligence” to

Jan 1, 2003

By F. T. Cawood

Monitoring of the slopes of surface mines can prevent loss of life, loss of equipment, loss of production and possibly the loss of the mine. The effectiveness of such monitoring depends on the extent to which slopes give adequate advanced warning before failing, and on the ability of the monitoring system to detect such warning. In this paper an overview is given of slope monitoring requirements, from both the geotechnical and survey points of view, as well as the types of equipment and instrumentation that are available. Legal issues relevant to slope monitoring are also dealt with. It is concluded that conventional geotechnical and survey instrumentation will continue to have their place in slope monitoring. However, the slope monitoring scene has changed substantially in recent years. A real and volume-based monitoring equipment is now available and this has provided, and will continue to provide, the means to improve safety, and to enhance productivity in mining. Its benefit to slope management is substantial. In the near future it is expected that data obtained from such equipment will add a much needed new dimension to slope engineering, and be used to improve slope designs and to optimize slope angles.

Jan 1, 2006

By L. Chen, G. A. Brooks, S. A. Nightingale

The dissolution of alumina and magnesia has been investigated using laser scanning confocal microscopy (alumina) and a rotating finger apparatus (magnesia) to assess the effects of temperature, composition and forced convection on the rate of dissolution in CaO-SiO2-Al2O3based slags. The two techniques have differing strengths and limitations, and provide complementary methods for studying dissolution. Alumina dissolution was studied for temperatures from 1477 to 1577°C. Based upon the data, the rate controlling mechanism was thought to be mass transfer control in the slag. The diffusion coefficients for the alumina particles are estimated to be in the range 10-11to 10-10m2.s. MgO degradation for sample rotation speeds of 50 to 800 rpm at 1500 and 1530°C was studied for both congruent and incongruent dissolution. The results show that the rate of dissolution for this is primarily controlled by a diffusion mass transfer mechanism for congruent dissolution except at the highest rotation speed. For incongruent dissolution, the mechanism is much more complex, with the morphology and distribution of the spinel reaction product having a significant effect. At high speeds and prolonged times, mechanical forces played a major role in the degradation process. Keywords; kinetics, corrosion, refractories, dissolution rate, inclusions, mass transfer, slags, steelmaking

Jan 1, 2004

By I. A. Minaev

The conditions of a stability of metallurgical films on a surface of solid on the basis of classical regularities of a thermodynamics are considered. For specific conditions of metallurgical processes the basic equations relevant to non-metallic inclusions (product of steel killing) migration and transfer through the interface boundary of metal-slag are obtained. The basic criteria equations of conditions of stability of metallurgical dispersed systems are developed in view of films formation. The probable thermodynamics reason of wetting due to formation of stable films are discussed. The experimental measurement of thin and thick films elastic resistance for metallurgical systems are carried out and the results are discussed. The presence of a wetting thick film increases stability of dispersed systems (facilitates an inverse implication of non-metallic inclusion in a melt) due to a barrier effect of wetting films. The quantitative evaluations of non-metal inclusion stability for steel in contact with any metallurgical slag are carried out. The results are in accordance with technological experience. Keywords: Inclusion removal, Film thermodynamic, Slag-metal dispers system

Jan 1, 2004

Decision-making regarding plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g per ton of fresh feed has been assumed a reasonable starting point, with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2013

By M. M. Valenta

A number of challenges face platinum concentrator plant operators. These challenges include the increase in operating costs, the increase in smelter cost for the processing of concentrate, the shortage and cost of power, and the tightening of specifications on concentrate quality by the toll-smelting operations. Over the years the focus has moved from extracting the platinum group metals (PGM) from the Merensky Reef to the UG2 reef. This has a number of advantages, including the higher ?basket price? for UG2 concentrate, reduced mining cost per unit volume as a result of the higher density of UG2, and the reduction in overall concentrate tonnage to be smelted. In many cases the Merensky ore has been fully exploited and it makes sense for the focus to shift to the UG2 ore that can be accessed through the Merensky shaft infrastructure. The presence of relatively high levels of chromite in UG2 concentrate is, however, a major disadvantage due to the problems associated with smelting such a concentrate in conventional submerged arc furnaces. In addition to increasing the specification on the minimum PGM grade of concentrates, smelters have had to impose strict specifications on the levels of chromite in the concentrate. The threat of high penalties has forced concentrators to change their modus operandi, often resulting in a significant loss in recovery. The final concentrate grades and PGM recoveries are shown to vary significantly throughout the industry. The reasons for this include varying ore mineralogy and different operating philosophies. This would therefore imply that the opportunity exists to optimize the operations by considering fundamental aspects such as the PGM mineralogy and the application of appropriate technologies. By returning to the fundamentals of flotation and applying the findings of detailed process reviews, it has been possible to increase the concentrate PGM grade, reduce the concentrate chromite grade, and in some cases increase the recovery of PGM to concentrate. This paper presents case studies where this approach has been used to successfully optimize concentrator performance, resulting in lower operating cost and higher PGM production. Keywords Process optimization, platinum concentrator, milling, flotation, grade, recovery

Jan 1, 2011

By D. G. Krige

For the purpose of determining confidence limits for ore grade estimates, an extensive simulated database was used, which included 1728 ore blocks with ?actual? grades and the corresponding estimates based on ordinary and simple kriging. The practical results show that conditional unbiasedness is essential and that acceptable confidence limits can then be set using Normal theory for the simulated error distribution based on the logarithms of the ratios of ?actuals?/estimates with a variance related to the kriging variance. The mean of the data used to prepare the variogram and the estimated block grade are to be used properly in this approach. A practical analysis was also done of the actual point and block data from a very large mined out Carbon Leader area. The distributions of the actual grades for two levels of block sizes with different levels of variability were fitted using three models, ie. two three and compound lognormal. The trends of tonnages, grades and relative profits for a range of pay limits, as well as the usual tonnage-grade curves, show a practical insensitivity for the choice between the three lognormal models considered.

Jan 1, 2004

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By D. Diering

Having agreed to perform this task, I naturally started to wonder what on earth I was going to talk about, and on reviewing the literature I was surprised at how little I knew and how much I?d forgotten about the origins of this industry. For example: ?I?d forgotten that the Chinese invented black powder at least 1 000 years ago, back in the 10th century (although some say this invention occurred 2 000years ago). ?I didn?t know that Roger Bacon was the first person in the Western World to give exact directions for the making of gunpowder in 1242 and to understand its potential. Pepper?s Playbook of Metals quotes:?...above all, he is named as the discoverer of gun-powder, a material which has brought more wonderful changes in the great family of man than the most potent elixir that could have been devised to prolong life?.

Jan 1, 2000

By E de Villiers

Several methods exist by which the capacity of a dense media separation (DMS) plant can be improved: 1) Increase the feed rate in spite of efficiency 2) Replace with bigger equipment 3) Add whole new module 4) Replace total plant 5) Change over to four shift/ seven days per week roster 6) Replace with alternative process 7) Increase the availability and utilization Options 1 ? 6 have varying degrees of cost implications. The seventh option would seem to be the easiest. Normally it is also the function of the plant operating and maintenance team to maximize this. Usually higher operating and maintenance cost are associated with an increase in these parameters. A general principle that is applicable to plants and systems is that as the complexity increases, the total availability decreases. By simplifying the flow line it may be possible to reduce cost while at the same time increase the availability and utilization. The typical standard DMS flow line contains components that compensate for the variance in pump performance or for the inefficient recovery of ferrosilicon with additional equipment. Things have changed though: 1) Advanced electronic control and monitoring is possible 2) More efficient magnetic separators are available 3) New more user friendly densifiers are available ORIGINAL FLOW LINE In principle the process consists of four flow lines or streams 1) Ore flow ? the feed is divided into a waste and product stream by means of the separating vessel

Jan 1, 2006

By Z. Zhang, R. G. Reddy

Experimental and thermodynamic modelling studies on the structure of alkali borate melts and properties are discussed. A thermodynamic structure model for alkali borate melts is developed to describe the distribution of structural groups in the alkali borate melts as a function of composition. A qualitative interpretation for the boron anomaly in viscosity has been proposed, which regards the boron anomaly as a manifestation of the various antithetical effects caused by the introduction of alkali oxide into boric oxide. It has been found that the viscosity of alkali borate melts increases or decreases according to the changes in rigidity and spatial connectivity of the glass network structure, which is the function of temperature and composition. These concepts with some key examples are discussed in relation to their usefulness and practicality in industrial slags. Keywords: alkali borate melts; structural model; activities; structural groups; viscosity;

Jan 1, 2004

By Marko Lampi, Marc Nicolle, Janne Karonen, Kari Valkama

"In the ten years from 2003 to 2013 global mine production of copper has increased by over 23% to meet demand while the weighted average head grade has dropped from 0.9 to 0.7% Cu. These divergent trends of increasing demand and declining economic grades will extend the life of many existing mines and improve the viability of marginal and/or complex copper deposits. Against that context this paper outlines hydrometallurgical copper sulphide leaching options as alternatives to the more conventional pyrometallurgical processing route of copper sulphides. Three copper sulphide leaching and refining processes are discussed: total pressure oxidation, ferric sulphate leaching and copper chloride leaching. The effect of mineralogy on the choice of processing technology is discussed as well as some of the unit processes used. Additionally, possible benefits that a hydrometallurgical process may offer over an existing pyrometallurgical route are discussed. Subsequently, two very important aspects to the development of projects involving the leaching of copper sulphides are discussed. Finally, a number of conclusions are presented that will be useful to keep in mind when considering projects involving the leaching of copper sulphides. INTRODUCTION In the ten years from 2003 to 2013 global mine production of copper has increased by over 23% to meet demand while the weighted average head grade has dropped from 0.9 to 0.73% Cu (Murphy, 2014). If these divergent trends of increasing demand and declining economic grades continue, they will contribute to the extension in life of many existing mines and improve the viability of marginal and/or complex copper deposits. Against that context, this paper outlines hydrometallurgical copper sulphide leaching options as alternatives to the more conventional pyrometallurgical processing route for copper sulphides. Three copper sulphide leaching and refining processes are discussed: total pressure oxidation, ferric sulphate leaching and copper chloride leaching. Ferric sulphate leaching and copper chloride leaching are carried out at atmospheric pressure while total pressure oxidation takes place at elevated pressures."

Jan 1, 2015

By E. Swart

The purpose of this paper is to provide an overview of the current legislative framework for mine closure within South Africa as well as the new requirements in terms of the Mineral and Petroleum Resources Development Act, 2002. The roles and responsibilities of Government, the mining industry and other stakeholders and confusion caused are also highlighted.

Jan 1, 2003

By M. Görnerup, A. Kapilashrami, Seetharaman. S., A. K. Lahiri

Simultaneous reduction and foaming of chromium-rich slag have been studied in a laboratory furnace equipped with X-ray image analysis. Reduction of the metal oxides by graphite generated CO, which caused the melt to foam. The slag composition continuously changed due to reactions and dissolution of lining. Gas generation rate, foam height, and gas bubble size were studied and correlated to slag composition. Viscosity increased significantly during the experiments due to a change in slag composition. Bubble sizes varied little during the progress of reactions but differed considerably for different slags. Bubble sizes were largest for V2O5 containing slag, which is contrary to the general understanding that the presence of strong surface active agents reduces the bubble size. The foaming index did not follow expected trends for bubble size and viscosity, suggesting that foaming index is not a suitable parameter for discussion of foams under dynamic conditions. Keywords: slag, foaming, dynamic conditions

Jan 1, 2004

By S. Vorberg, J. Preussner, B. Fischer, U. Glatzel, R. Völkl, M. Wenderoth

Pt-Al-X alloys have shown good mechanical properties and adequate oxidation resistance. Starting from a promising Pt-Al-Cr alloy, the influence of Ni additions was investigated. After ageing finely dispersed precipitates are observed. Nb, Ta, Ti and Re increase strength when added as partial substitute for Al. Minor additions of B increase creep resistance and rupture time remarkably, owing to strengthening of the grain boundaries. The evolution of the alloy development programme as well as selected properties of the multi-component Pt-base alloys are presented.

Jan 1, 2006

By G. M. J. van Heerden

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The Union Section of Anglo Platinum is situated ±18 km west of the town of Northam on the north-western rim of the Bushveld Igneous Complex. Both the Merensky and UG2 reefs are mined. Support of the Merensky stoping areas with rock bolts is specifically problematic due to the stoping width restrictions varying around 90 cm. The installation equipment of in-stope rock bolts and the effectiveness thereof in the Merensky stoping areas was critically evaluated. In order to do this a background research on the need for better on-the-face support had to be conducted. The need for improving the rock bolt drilling and the equipment had to be investigated and the financial implications and justifications for the improved equipment examined. To conduct the search an overall study was done on the rockfalls and safety aspects throughout the platinum industry in South Africa and specifically Union Section. It was found that most of the rock falls in the Merensky stoping areas of which ± 70% are less than 1.2 m in thickness generally occurs within 4 m from the face and causes ± 60% of the in-stope injuries. Serious shortcomings had been identified with respect to the airleg, rock drill machine and the drill steels used in the drilling of the rock bolt holes. Through experimentation, using a testing frame built for this purpose on surface and with the co-operation of mine staff and suppliers, a number of possible modifications were identified and tested. This resulted in the final product with which it was possible to drill a 1.2 m hole in the hangingwall of the stopes ranging with an angle to the hanging from 90° for a 90 cm stoping width and 67° for a 80 cm stoping width. It is confidently concluded that this system will effectively improve the total face support and result in a substantial reduction of rock falls and consequently the occurrence of injuries and fatalities in the Merensky stoping areas. The installation of rock bolts on the face with the modified drilling equipment will increase the direct support, but the system has a potential of a substantial reduction in the profile stick support density and an increase in productivity in the stoping areas due to fewer occurrences of rock falls. It was finally concluded that effective modifications to the drilling equipment for rock bolt in-hole drilling could be made and the installation thereof in the stope face is adequately justified.

Jan 1, 2002

By L. Munsamy, B. J. Madden

OpenRisk, an open cast risk rating system, takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and operational parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all the strip mines would use an identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. This system has been made practical and easy to use. Therefore, this tool can be used by personnel from other disciplines not directly related to rock engineering. OpenRisk system has been in operation at nine Anglo Coal and other open cast mines. It adequately detects areas of high risk and generates adequate remedial solutions to reduce the risks. Awareness of the personnel has been higher at the sites that use OpenRisk. The proactive approach of OpenRisk ensures that all personnel are aware of risks in the pits and how to deal with potential risky areas.

Jan 1, 2006