Search Documents

In a gold CIP/CIL circuit, adding new circuit water to a final tails thickener and then directing the thickener overflow to the head of the circuit significantly reduces the cyanide concentration at the TSF discharge spigot. The new water is used to dilute the final tails. The dilution and recycle of the tails in this manner may have the added benefit of reducing reagent consumption, in some cases to the point where the reagent savings justify the expenditure and Cyanide Code compliance is achieved at no extra cost. Potential circuit configurations and water recycles can be modelled by splicing a flowsheeting and thermodynamics package, such that changes to the composition of the water can be reduced to chemical speciation with a Gibbs free energy minimisation enabling a complete understanding of the circuit water chemistry.

Jan 1, 2007

By A. S. Geldenhuys, L. S. Leal Filho, D. A. Deglon, T. C. Souza Pinto

The Brucutu iron ore mine (Minas Gerais, Brazil), is Vale`s largest iron producing operation achieving around 21 million tons by flotation of iron ore pellet feed per annum. The run of mine is mainly composed of hematite (70%) and quartz (30%). After preparation (comminution and sizing), the slurry is submitted to reverse cationic flotation of quartz under basic conditions (pH=10.5). Corn starch (500g/t) is used to depress Fe-bearing minerals and alkyl (C10) ether amine is the collector for quartz. The flotation circuit is arranged in a “coarse” section utilizing dated 28m3 square Wemco cells, and a “fine” section utilizing modern 160m3 tank cells. The “coarse” flotation circuit treats material from the deslime cyclone underflow while the “fine” circuit treats material from the deslime cyclone overflow and the pulp product from the “coarse” circuit scavenger 2 bank. Evaluation of process performance is of high importance as even small gains can lead to large improvements for this high throughput plant. Cell-by-cell samples of the froth products, selected feed and pulp-products were analyzed for flow-rate, overall chemical composition, and particle size distribution. Bank-by-bank samples of the feed, froth and pulp products were analyzed on an assay-by-size basis. In addition, the flotation cells were hydrodynamically characterized and gas dispersion parameters assessed. The detailed experimental program resulted in a thorough characterization of the process and enough information to produce a calibrated floatability component model. Longer mainline residence time results in significant Fe2O3 losses while yielding little benefit in terms of SiO2 grade. Scavenger 2 has twice the residence time of scavenger 1 while having to treat only 10% of the SiO2; resulting in high Fe2O3 recoveries to the froth and poor separation. In addition, it is shown that the Fe2O3 exhibits true flotation behavior resulting in increased Fe2O3 losses. The detailed data collection campaign coupled with in depth data analysis and modelling gives unprecedented information and highlights avenues for optimization that was previously unknown. Keywords: Froth Flotation, Process modelling, Process evaluation, Metallurgical survey

Jan 1, 2020

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant. It was developed as part of the AMIRA P9 project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. This paper describes the use of the FCTR in validating the AMIRA P9 flotation model and modelling methodology. In 2001 the FCTR was installed and operated in parallel with WMC's (now BHP Billiton's) Kambalda Nickel Operation. The FCTR was operated using four different circuit configurations of increasing complexity. Metallurgical surveys, cell characterisation measurements and batch flotation tests were performed around each circuit. This allowed the calibration of a number of flotation models using a combination of data from one, two, three or four circuit configurations. The calibrated flotation models were then validated using predictive validation. To do this, data around a further five FCTR circuit configurations were collected (three of which are presented in this paper). The performance of each of the five circuit configurations was predicted using JKSimFloat V6.1 and the parameters from the various calibrated flotation models. The predicted performance was compared to the experimentally determined performance of each circuit. The validation of the AMIRA P9 model was shown to be largely successful except in the case where the reagent addition (depressant) to the validation circuit was different to that in the calibration circuits. The results also provided information regarding the required complexity of the calibration circuit and how many calibration circuits are required to obtain an accurate prediction of circuit performance. These results have increased the confidence in the AMIRA P9 flotation modelling methodology and have provided important information on what data must be collected to allow the accurate prediction of plant performance using the floatability component modelling approach.

Jan 1, 2007

It is suggested that an increase in the production from thin coal seams in South Africa is necessary, and that a substantial amount of any increase will be mined by the bord-and-pillar method. For the purpose of this study, a thin coal seam was regarded as any seam 1,5 m thick or less to the minimum thickness at which mechanized equipment can operate in bord-and-pillar workings. The equipment being utilized in thin-seam bord-and-pillar layouts includes conventional equipment, load-hauldump cars (scoops), and drum-type and Fairchild-Wilcox continuous miners. Comparisons are made of these types of equipment for bord-and-pillar mining at various seam thicknesses within the thin-seam range. The evaluations involved production rates and the cost of extraction for South African conditions, use being made of an existing computer modelling technique in the generation of production rates. The indications are that, for seam thicknesses greater than 0,9 m, drum-type continuous miners utilizing continuous haulage are the most productive and cost-effective equipment at present operating in thin-seam bord-and- pillar workings. Where seams thinner than 0,9 m are to be exploited, Fairchild-Wilcox continuous miners, particularly the Mark 22, produce the most coal at the lowest cost.

Jan 1, 1984

By D. M. Poulter, J. N. Brooke, P. H. Williams

"The complexity of the mining and metallurgical operations of Nchanga Consolidated Copper Mines, Limited, has made it necessary to use computer-assisted planning techniques in order to maximize copper production and marginal contribution to profit. The most successful of the Group Production Scheduling systems utilized linear programming to optimize the concentrate routing only. This third-generation system was commissioned in March, 1968.It bad become necessary by March, 1970, to expand the long-term planning activities and to take into account new mines and new concentrate treatment schemes. Technical difficulties and manpower limitations made it impossible to expand the third-generation system, and it was decided to construct a new Group Production Scheduling system using only linear programming.The plant models in the new fourth-generation system are based on data available from the monthly reports of the metallurgical plants. The models consist of mass balances and empirical relationships. Matrix coefficient assignment and management reports are produced using a Report Generator Language designed for linear programming data files. The development of this system is an example of a user application of a system package."

Jan 1, 2014

By von Wielligh. L., D. G. Hattingh, M. N. James, W. Thomas

"SynopsisThe process of joining materials by friction is based on generating the heat necessary to create a solid-state mechanical bond between two faying surfaces to be joined. In simple terms, the components to be joined are subjected to frictional heating between rubbing surfaces, causing an increase in interface temperature and leading to localized softening of interface material, creating what is described as a ’third body’ plasticized layer. This plasticized zone reduces the energy input rate from frictional heating and hence prevents macroscopic melting. The plasticized layer can no longer transmit sufficient stress as it effectively behaves as a lubricant (Boldyrev and Voinov, 1980; Godet, 1984; Singer, 1998; Suery, Blandin, and Dendievel, 1994). The potential for this solid-state frictional joining process to create high-performance joints between, for example, dissimilar materials with limited detrimental metallurgical impact, and reduced defect population and residual stress level, has had a very significant impact on fabrication and repair in industrial sectors such as transport. This paper presents a brief overview of the advances made within the family of friction processing technologies that could potentially be exploited in the nuclear industry as alternative joining and repair techniques to fusion welding.Modern friction processing technologies can be placed into two main categories: those that make use of a consumable tool to achieve the intended repair or joint (friction stud and friction hydro-pillar processing) and those making use of a non-consumable tool (friction stir welding). The most mature friction joining technology is friction rotary welding, where a joint is formed between original parent materials only. A new addition in this category is linear friction welding, which opens the potential for joining complex near-net-shape geometries by friction heating. The continuous innovation in friction processing over the last 25 years has led to the development of a number of unique processes and applications, highlighting the adaptability of friction processes for specialized applications for high-value engineering components.IntroductionAssessing the potential for using alternative joining and repair techniques for specific applications in a given industrial sector is informed by an appreciation of the current size and potential growth in that sector. Power generation by nuclear fission has been out of favour over the past few years, due to several high-profile nuclear incidents, e.g. the Fukushima Daiichi nuclear disaster, as well as concerns over disposal of nuclear waste and spent fuel rods. However, due to rapid increases in the demand for electricity, coupled with many fossil-fuel fired plants reaching end-of-life, there is renewed interest in installing additional nuclear capacity."

Jan 1, 2015

By G. Bueno, L. M. Tavares, T. M. Campos

Iron ore pellet feed pressing has been one of the first and most successful applications of High- Pressure Grinding Rolls (HPGR) in the minerals industry. Vale S.A. has been one of the pioneers in this application, currently with six HPGRs in operation in the pelletising plants of the Complexo de Tubarão (Brazil). In spite of the important advances in the technology, risks still exist when scaling-up the process from small-scale information. The present work takes advantage of the recent advances in the mathematical modelling of the HPGR performance, using the population balance model to evaluate the modified Torres and Casali model prediction in iron ore pellet feed pressing for different scales of operation. Results are presented that compare the HPGR performance in different operational scales for iron ore pellet feed pressing, demonstrating the confidence of this model-based approach for scale-up to full-scale HPGRs used in pressing iron ore concentrates. Keywords: Scale-up, HPGR, pellet feed, modelling, simulation

Jan 1, 2020

By C. Hartford, T. Holmes

Bulk-solids handling systems are often the most over-looked component and thereby weakest links in a processing plant’s value chain. Since their performance can dictate that of the entire operation, they actually deserve special attention. When designing a liquid handling plant, density and viscosity are well known and commonly used as design parameters. Bulk solids however, differ. While the design process is similar, the relevant parameters in handling bulk solids are instead friction, cohesive strength, compressibility, and permeability. These then vary depending on the mineralogy, particle size distribution and shape, moisture content, storage time-at-rest, temperature, and consolidation pressure. With so many variables, it becomes important to characterize each individual bulk solid across the full range of representative process conditions within the handling system, plant wide – or if you are not very lucky, suffer the consequences of poor material flow. Measuring flow properties and applying them correctly in bulk solid handling system design reduces project risk, saves significant capital, and drastically increases throughput, especially when done in the early stages of a project. Keywords: Flow Properties, Bulk Solids, Process Conditions, System Design

Jan 1, 2020

By D. J. Briggs

The use of backfill for regional and local support is receiving increasing attention in the South African mining industry. To ensure that fill materials meet the purposes for which they are intended, a test procedure to characterize the load-deformation characteristics for a particular fill was developed. The major variables identified as influencing the load-bearing proper- ties of backfill include particle size distribution, porosity, width-to-height ratio, strain rate, confinement, water content, and additives. The influence of these variables on the performance of backfill is described in relation to crushed waste, dewatered tailings and deslimed tailings. These investigations confirmed that no single test could be used to define the overall stress-strain behaviour of a selected fill. Nevertheless, resulting from this work, a preliminary standard test procedure for uncemented backfill materials, com- prising a suite of tests in unconfined and confined compression, has been formulated. This test procedure is a significant advance towards a more meaningful evaluation of fill materials. Test results will also provide numerical information for input use in computer programs for the design of mine layouts incorporating backfill.

Jan 1, 1988

By J. Petersen, S. W. Robertson

Heap leaching is used extensively for the processing of low-grade copper, gold, and uranium ores. The hydrodynamics is often the most important factor that limits the rate of metal recovery. Over the past decades the author has performed physical and hydraulic testing of a large number of ore samples considered for heap leaching. The data were reviewed to investigate the effect of physical properties such as particle size distribution (PSD) and bulk density on the hydrology. The unsaturated flow through the bed is traditionally modelled with soil science models such as Brooks-Corey (BC) and Van Genuchten-Mualem (VGM), which relate the hydraulic conductivity to the degree of saturation, also known as the hydraulic conductivity function (HCF). However, most authors found a disconnect between the saturated hydraulic conductivity (KS) and the rest of the HCF, which is explained as resulting from a transition from capillary-to gravity-controlled flow. However, the author found no such transition, and found the flow to be governed by capillary flow throughout. Traditional BC or VGM fits were found to be appropriate, however it was necessary to modify the model to include a point of inflection, above which the hydraulic conductivity remains constant while the moisture content keeps on increasing. It was proposed that this is the result of unconnected or poorly connected pores, which fill with solution but do not create additional flow channels. The point of discontinuity was also found to correspond with the air entry point, measured independently from the air conductivity curves. On average, the air entry point corresponds to the experiential rule that the void saturation should remain below 65% for aerated heaps.

Dec 11, 2024

"Chairman: Prof A. E. H. BLEKSLEY Rapporteur: Prof J. ELBRONDPanel Members: Prof J. C. Griffiths, Prof T. E. Hawkins, Mr A. C. Langton, Mr M. Splaine, Mr A. WeissThe reasons for failure of computer applications in the mineral industry and the direction of future developments.The Chairman opened the discussion by elaborating on the disappointment felt by some authorities with the lack of progress in the application of computers in the mineral industry during the last ten years, and posed the question to the panel : 'Do you agree that the computer age has not come up to expectations?'Mr Langton said that although there seemed to be a tremendous amount of brainpower applied to the theoretical side, he thought that the production men had not got all the help from computers that could have been given to them. The computer, said Prof Griffiths, is as yet a new tool which should not be used to do old things in old ways. To learn to use the computer will take time. After all, he said, it had taken 400 years after the introduction of the printing press to achieve general literacy, and perhaps it will take 40 years after the introduction of the computer to achieve `numeracy'.In Mr Weiss' view, the reason for the feeling of disappoint¬ment lay in the focussing of attention on the computer. The blame, if any, lay with the people surrounding the computer, that is, the analysts and programmers, to whom the emphasis should be shifted.Prof Hawkins said that he thought that some applications of the computer in the mineral industry had been successful, such as, for example, the compilation of payrolls. Reasons for failures in other areas were to be sought in the fact that the people connected with computers had failed to realise that they were merely part of a system. They had not understood the power structure of the organization which their work tended to change, and were therefore not prepared for the inevitable conflict with the production men.In Mr Splaine's view the production man had not received the assistance he could have had from the computer people because he may possibly not have allowed this to happen.Prof Bleksley concluded from these opinions that the promise which computers had ton years ago had not been fulfilled and added that the opinions expressed by the panel had intruded on his next question which was: 'Is the reason for this that people are involved?Prof Hawkins elaborated on his previous theme, namely, that of computer people in relation to management. Com-puter people, he said, were trying to impose change on management but were not prepared to share the responsibility for these changes. In fact, they wanted their work to be distinct and separate, and, as far as management was concerned, changes would be made when management believed that these would be less agonizing than no change at all."

Jan 1, 2014

By E. Arghavani, S. H. Amiri, S. Zare, F. Sepehri, M. Ramezanizadeh

Mineral processing plants include different stages like crushing, grinding, classification and concentration, all of which have partially affect the final product. To identify and solve the related problems of each stage, process audition should be carried out continuously to find the major solutions of improving product and decreasing the maintenance and operating costs. The Iranian Gohar-Zamin iron ore beneficiation plant consists of equipment such as gyratory and cone crushers, high pressure grinding rolls (HPGR), ball mill, dry and wet double-deck vibrating screens, hydrocyclones cluster, magnetic drum separators, thickener and horizontal vacuum belt filters. The defects of initial design as well as current non-standard operating conditions of equipment were monitored and detected and the opportunities for process optimisation were presented as follows: establishing the control loop of power draw for cone crushers, the modification of feeding chute in cone crushers to minimise the non-uniform wear of parts, removing segregation in the fresh feed bin and screen’s circulating load chute in order to provide the proper feed to HPGR, reducing wear rate on HPGR rolls surfaces, decreasing the amount of rejected materials in screen, equalising the solid content and particle size distribution (PSD) of feed in all magnetic drum separators and equalising the PSD of hydrocyclones overflow. This paper provides a guideline for the mineral processing industry to focus its efforts on process design to deliver the efficiency with minimum capital costs. Keywords: Process audition, gyratory crusher, cone crusher, HPGR, screening, hydrocyclones, magnetic drum separators

Jan 1, 2020

By D. Sethuram, P. G. Koppad, S. Iyengar, R. Shobha

TiB2 and CeO2 particle-reinforced Al6061 hybrid composites were manufactured using stir casting and hot rolling techniques. The base alloy and composites were hot-rolled at 500ºC and a 50% reduction was achieved through 12 passes. The effect of varying TiB2 and CeO2 particle additions on the microstructure and mechanical properties of the Al6061 matrix was studied. Scanning electron microscopy showed uniform dispersion of both the reinforcements, with good interfacial bonding. Microhardness and tensile properties like yield and tensile strength were found to be higher for hybrid composite with 2.5% TiB2 and 2.5% CeO2 compared to Al6061 alloy and other hybrid composites. The increased tensile strength is attributed to good dispersion and interfacial bonding between the particles and Al6061 matrix. Fracture analysis using a scanning electron microscope revealed ductile fracture for the Al6061 alloy and mixed characteristics of ductile-brittle fracture for hybrid composites

Oct 1, 2021

By D. D. Howat, J. van der Colf

This paper is the first in a series of three dealing with this subject and also with the rate of oxygen removal from the slags in the presence of solid carbon and with the physicochemical properties of the reduced slags. For selected members of the system, the melting temperatures and primary crystallization products were determined. as were the viscosity and the electrical resistivity of the corresponding melts. All the experiments were conducted in a neutral atmosphere. Where determined, the primary phase was found to be either perovskite or magnesium aluminium titanate. The composition variable exerting the most pronounced influence on viscosity or resistivity was found to be the basicity expressed as the mass ratio (CaO + MgO)jSiO,. The ratio CaOjMgO became important only at Iow basi<:ity values. Although generally there is a direct proportionality between log (viscosity) and log (resistivity), slags h&apos;lving either a very high silica content or a very high titania content have anomalously Iow electrical resistance.

Jan 1, 1979

By I. B. Fernandes, M. A. Reuter, A. Abadias Llamas

Metallurgical simulation and evaluation of the resource efficiency of whole production processes are of key importance for impact assessment, in terms of environment and resources. Exergy is a measure of resource consumption, taking into account energy, raw materials, water, and chemicals; which allows for the evaluation of different technologies to find the most resource efficient and environmentally friendly process. This paper compares the sustainability for production of rare earth magnets from primary and secondary resources through an exergetic evaluation of the production process, in addition to traditional life cycle assessment (LCA). The methodology makes use of simulation tools for tracking material flow and resources used, based on thermodynamic laws, from ore exploitation to magnet production and recycling. It highlights areas with the greatest potential for improvements in terms of resource consumption and environmental impact generation, having a thermodynamic-validated flowsheet for primary and secondary production of NdFeB magnets, present in several low-carbon technologies, such as wind turbines, electric vehicles, and cooling systems. It demonstrates the minimum exergy destruction for magnet production, through an irreversibility breakdown chart, showing where irreversible material and energy losses occur. Results show that CO2-equivalent emissions for producing NdFeB permanent magnets from primary resources could be twice as high when compared to magnets produced from recycling technologies. The theoretical maximum exergetic efficiency for primary production is 57.61%, whereas for permanent magnets produced from secondary resources, the exergetic efficiency reaches up to 82.89%. Two magnet recycling technologies were evaluated, i.e. in acidic medium and via hydrogen decrepitation, and it was observed that their exergetic efficiency and environmental impact performed better than production from primary resources. Keywords: Resource efficiency, exergy analysis, permanent magnet recycling, process simulation, system design

Jan 1, 2020

By H. Manurung, I. M. Bendiayasa, W. Astuti, and H. T. B. M. Petrus, F Anggara, K. C. Wanta

The leaching kinetics of cerium (Ce) and yttrium (Y) in sodium-hydroxide-digested non-magnetic coal fly ash using acetic acid were investigated. The variables analysed were pH, solid-to-liquid ratio (S/L), and temperature. The results show that cerium and yttrium's maximum recovery was 57.33% and 58.36%, respectively, under leaching temperature of 90°C for Ce and 60°C for Y at pH of 1,74 and 10 g/mL solid-liquid ratio in 240 minutes. Increasing the leaching time to more than 120 minutes did not significantly improve the results. After the magnetic separation process, the ICP-OES analysis shows a slight increase in the concentration of cerium and yttrium on nonmagnetic components. The XRD and ICP-OES analysis for the sample before and after silicate digestion shows that 40% silicate was dissolved. The calculation of apparent activation energies of leaching using the Arrhenius law for the leaching of cerium and yttrium gives 22.72 kJ/mol and 35.84 kJ/mol, respectively. The kinetic leaching model of cerium and yttrium all fit Dickinson's new shrinking core model. The calculation results show that the leaching reaction is controlled by combining interface transfer and diffusion across the product layer.

Nov 6, 2024

By D. F. Caicedo, I. A. Brum, L. A. Betancourt

Ferricyanide ()()*is one of the most stable cyanometallic complexes present in the gold mining effluents. This cyanocomplex is hard to degrade by natural attenuation and generates a negative impact on aquatic environments. Although free cyanide (CN-) can be obtained by acidifying the solution, the CN- is lethal for all forms of life. The oxidation of ()()* in a typical photocatalitic system was evaluated with the addition of H2O2. To verify the degradation, chemical parameters, such as free cyanide, the formation of ammonia, nitrate, and total iron were analysed at the end of the process. The degradations obtained were up to 70% in a heterogeneous photocatalysis system with TiO2, and a low rate of dissociation was observed by photolysis. The best result was achieved with the H2O2 and TiO2 photocatalytic system, and the stoichiometric concentration was about 2.5 times less than the peroxide used in the real gold mining industry, reaching 83% degradation. The photocatalytic process obtained less toxic byproducts than the original synthetic ferricyanide used as mining wastewater. Keywords: Cyanide, heterogeneous photocatalysis, titanium dioxide, UV radiation, gold wastewater

Jan 1, 2020

By P. Leeuw, H. Mtegha

"The aim of this paper is to enhance the understanding of the nature of mining input technologies in the South African mining industry. In the context of this research, mining inputs refer to input technology into the activities in mining engineering fields, which include mining-related production activities, rock engineering, mine ventilation, and mine transportation (handling of personnel, material, broken rock, and pumping). Input technologies in supporting fields such as geology, other engineering disciplines, human resource, procurement, finance, as well as downstream fields that include metallurgy, and marketing of minerals, were disregarded.The mining input technologies were divided into 12 nodes, and data from a sample of 150 first-tier mining suppliers was analysed. It was found that, in general, there is a high local content in mining input technologies, particularly as regards technical support services, artefacts, and machine technologies. This points to the presence of mining-induced backward linkages in the South African mining industry. The majority (83%) of companies that provide input technologies into mining are located in Gauteng Province, and relatively few are found in provinces where mining is concentrated such as North-West, Limpopo, Mpumalanga, and Free State. IntroductionSouth Africa is well endowed with minerals, with more than fifty different minerals being mined throughout the country. For this and other reasons, mining is one of the crucial pillars in the South African economy and its importance is well documented (Robinson and von Below, 1990; Creamer, 2010; Department of Mineral Resources, 2015). In 2013, South Africa was the largest global producer of chromium, ferrochrome, platinum group metals (PGMs), and vermiculite and the second largest global producer of antimony, manganese, titanium, and vanadium (Chamber of Mines of South Africa, 2014). In 2013, the mining industry contributed 6.7% to South Africa’s GDP and was the fifth largest sector in the economy, as shown in Figure 1."

Jan 1, 2016

By G. L. Gomes-Sebastiao, W. W. de Graaf

"Gomes Sand is a quarry operation that produces sand and aggregate for the construction industry. The quarry is experiencing inconsistencies in the fragmentation and poor pit conditions as a result of poor drilling and blasting practices. This results in excessive downtime in the load and haul and crushing processes.A benchmarking exercise of the blasting practices was conducted to evaluate the effect of the inconsistency on the mining cycle. After changes in the blasting practices the downtime was reduced, which improved the crushing plant utilization by 4.9%. The improved blasting practices and more consistent fragmentation decreased the average number of loads lost each month due to jaw crusher blockages from 9.2% to 3.9% of plant throughput. The change in blasting practices also improved pit conditions. IntroductionGomes Sand is a quarry operation that has been in operation since 2009, producing sand and stone for the construction industry. The quarry was experiencing unacceptable blasting results. The repercussions included uneven pit floors, large amounts of oversize rock (>500 mm), and inconsistent fragmentation.The blast results affected the load and haul operations as well as the efficiency of the crusher. This resulted in downtime in the daily operations, and consequent production and revenue losses.The crusher product should have a top size of 50 mm. A blast fragmentation of <50 mm would improve the downstream operations and the crusher throughput.An investigation into the blasting practices was carried out to assess whether the downstream delays can be eliminated by improving the blast results. The exercise included:* Assessing if the designed blast layout is adhered to on the bench* Observing the quality and control of drilling* Observing the charging procedure of the blast-holes* Benchmarking the fragmentation consistency of the blasted rock using current blast design and practices* Analysing the throughput of the crushing plant* Investigating the power consumption of the crushing plant and determine if a change in blasting practices will affect this* Evaluating the hours spent by the hydraulic hammer on secondary breaking."

Jan 1, 2017

By V. Moodley

Strict implementation of International Standards for representative sampling of coal is difficult for routine monitoring, due to time, technical, and economic constraints. A large percentage of the total sampling variance arises from errors accumulated during the earliest stages of sample collection. Modified procedures on the precision of the final result leads to controversies between the sellers and customers for coal. Manual collection of coal samples violates the principle of correct sampling, that all fragments must have an equiprobable chance of being in the sample. In addition, manual size reduction of large numbers of samples is time consuming and involves human errors. A coal quality management procedure in alignment with the relevant ISO standards that describes the sampling protocol has been implemented, and current sampling and laboratory analysis of coal from base load mines (mines situated at the mouth of the power station) are well established. For import coal, sampling is performed during unloading by auto-mechanical sampling (AMS). Due to logistical and safety issues associated with multiple suppliers, Eskom opted for the coal to be sampled at source on a pre-certification basis. Online analysers provide a fast, accurate, real-time method of determining the total moisture and elemental composition of coal and is important to the coal industry for pricing, quality control, and reduction of SO2 emissions. Elemental analyses include S, Si, Al, Fe, Ca, Na, Mg, Mn, Ti, K and Cl. Measurement of S is dictated by the control of SO2 emissions from coal-fired power plants. Elements such as Na and Cl have adverse effects on boilers, causing fouling and slagging. Available online elemental analyser technologies include prompt gamma neutron activation analyses (PGNAA), recommended for major element determination, and pulsed fast and thermal neutron analysis(PFTNA), that is capable of measuring the major and minor chemical elements contained in coal. These systems utilize nuclear reactions to produce characteristic gamma rays that are used for identifying various chemical elements. By acquiring the gamma rays in three different time windows, there is a significant reduction of the background as compared with the spectra taken with a radio isotopic source.

Jan 1, 2009