Search Documents

By C. Gatschlhofer, A. Krammer, H. Raupenstrauch, T. Hochsteiner, A. Holzer, L. Wiszniewski

The rising demand for lithium-ion batteries, coupled with international climate targets, emphasises the need for circular economy and zero-waste recycling approaches. However, so far, no industrial-scaled solutions are available that fulfil global recovery targets. Therefore, a novel pyrometallurgical reactor was developed at the Chair of Thermal Processing Technology at Montanuniversitaet Leoben to avoid lithium slagging and recover volatile elements via the gas phase. Nevertheless, previous results show that several impact factors, including interfering elements or pre-treatment steps, strongly limit the recycling efficiency of black mass. To simulate the black mass and provide feedback on possible influences of pre-treatment steps, cathode material from production with additives of interfering elements was analysed regarding melting behaviour. The results show that formation of a further processable alloy was increased by almost 50% when pretreatment steps were excluded, indicating pre-treatment steps as a major influence to be considered within this specific recycling route.

Jan 1, 2023

By E. Kumar, L. A. Kumar

"A methodology is proposed to develop an optimization model to understand the impact of transporting minerals, from mines to the final destination, on air quality. Recently, there has been increasing concern about the combined effects of multiple activities over many years, and the regional environmental changes brought about by a single project. Environmental issues in the iron ore industry have highlighted the need to broaden the cumulative impact assessment. In this study, we simulated the optimal routes and quantity of materials needed to meet the destination plant demand based upon environment constraints (level of air pollution), as well as the cost of transportation and availability of materials. Multiple scenarios were developed to analyse the effects of changes in routes, alternative transport system (or multi-modal split), traffic congestion, and the cumulative impacts on air quality. The air quality impact zones of the study area were demarcated using a GIS technique. The expected outcome of the study is the selection of a suitable transport system for a particular site with the least impact on air quality, including the transportation route, relative to the minimum cost of transportation of the minerals from the mines to their final destination. The proposed methodology is evaluated with a case study. IntroductionIn India, the process of environmental impact assessment (EIA) has been focused primarily on the local impacts of projects, without considering regional environmental effects. Environmental clearances for proposed projects are based on reports of local impacts. However, any developmental project poses a potential risk to the environment as a whole, and not just in the immediate vicinity of the project. Recently, there has been increased concern about the combined effects of multiple activities over many years—the regional environmental changes due to development of a single project (Dutta, Mahatha, and De, 2004). Environmental issues throughout the country, particularly in the iron ore industry, have emphasized the need to broaden the analysis to include the combined impacts, or those forecast for a proposed region, on an existing environment. The most significant adverse environmental consequences of iron ore transportation are the deterioration of biodiversity and air quality (Kumar and Ajay, 2015)."

Jan 1, 2017

By T. E. Oates, W. Spiteri

In 2015, after amendments to the explosives regulations, stemming became a mandatory activity for all South African mining operations. There are, however, circumstances in which it is thought stemming has an adverse impact on the blasting outcome. Some of these circumstances include blasting in hot holes, in reactive ground, or when blasting a pre-split. In order to determine when stemming is necessary, its role in the control of adverse blasting phenomena and impact on explosive performance were reviewed. Stemming was found to play a significant role in the fragmentation process and burden movement. Additionally, stemming significantly influences the control of flyrock, air-blast, and toxic fume generation. The review of the literature indicates some motivation for not using stemming for presplit, trim, hot hole, and reactive ground blasting, provided the benefits associated with not stemming the holes outweigh the risks of stemming them. Best practice for stemming from the literature indicates a stemming length of 0.7 × burden is best for larger hole diameters, and 20 to 30 × Ø for smaller hole diameters. Crushed aggregate appears to be the most effective stemming material. The South African explosives regulations pertaining to stemming were found to be consistent with those of Australia and the USA.

Aug 1, 2021

By Huanhuan SU, Jianqiang Zhang, Zhongyuan Liu, Junwei Ma

The high-sulfur bauxite in Henan Province was used as raw material. The grinding fineness, pH value and collector dosage on its desulfurization performance, and industrial flotation desulfurization process were studied. The best flotation desulfurization conditions were grinding fineness of 75%, pH of 8.5, and collector of 600 g/t. “One coarse, one cleaning and one sweep” closed-circuit flotation was established as the industrial flotation desulfurization process. After the closed circuit test, the sulfur content of aluminum concentrate with the yield of 93% was 0.23%, and the sulfur removal rate was 83.16%, and the sulfur content of tailings (sulfur concentrate) was 15.09%. Keywords：High-sulfur bauxite under coal mines, flotation, desulfurization

Jan 1, 2020

By J. Saunders, N. Pretorius, G. Krafft, T. P. Katakwa

Imagine being able to see all the future planned mining activities in real time. This is exactly what SIMS (Short Interval Management System) will enable you to do. SIMS is a real time short interval control system that continuously measures and sets optimised plans for mining production processes. The system utilises algorithm-based software that takes resources (people, equipment, tasks, and workplaces) and gives you the best achievable plan. The algorithm was developed using methods found in the field of metaheuristics. A metaheuristic is a strategy to designed to efficiently search for optimal or near optimal solutions to problems that are very complex computationally. (Glover, 1986) There are several algorithms that have been developed to solve optimisation problems which are difficult to solve using traditional techniques. This has given rise to a field called evolutionary computing. (Simon, 2013) Examples of these techniques are genetic algorithms, particle swarm optimisation, and ant colony optimisation. These methods are used to solve problems in a variety of fields. As an example, Kok and Lane (2012) used particle swarm optimisation for equipment allocation in a mechanised underground mining environment. The first SIMS deployment took place in a platinum underground tabular mechanised mine near Burgersfort (province?) from 2017-2019. This included the development from a paper-based system to a fully operational online system. SIMS then moved to a second site and is currently being tested in a second platinum underground tabular mechanised mine in South Africa. Full deployment of the system is currently being phased in. SIMS was built in response to issues that have been plaguing the mining industry for years. These issues are all aligned into one major problem statement: how can we optimise mining production processes without compromising safety? This product was developed by combining years of mining experience with software development. SIMS is based on a four-pillar concept. Safety, productivity, accountability, and business improvement. SIMS uses a set of pre-configured mining and production rules, and with the resources that are available, to determine valid short term production plans. A background algorithm then determines the optimum plan to be executed. The system continuously produces a set of job cards that are pushed to respective operators on their allocated tablets. The management portal component allows you to view and manage all current and planned work on any connected device available. This allows real time visibility of completed, current, and planned work to operators, service departments and management, i.e., seeing into the future.

Sep 1, 2021

By P. F. Dicks, N. J. Shackleton, E. H. W. Theron, V. Malysiak

Flotation is a complex physical chemical process in which flotation reagents play a vital role in valuable minerals recovery and concentrate grades. This study examines the performance of new generation AECI Mining Chemicals (previously named Senmin) collectors. They were developed to enhance the valuable minerals recovery and flotation selectivity by tailoring the collectors to target specific valuable mineral species present in an ore and thus create added value for concentrators treating PGM ores. The case study was conducted on a Platreef ore, where batch flotation tests were performed and the concentrates were mineralogically characterised for PGE and BMS using QEMSCAN. Further batch flotation testwork was conducted on Merensky and UG2 ores from various localities in South Africa to confirm the trends observed for Platreef ore. The results have shown that there is a strong correlation between PGE mineral type and AECI Mining Chemicals collector type - clearly demonstrating that one reagent type does not fit all flotation applications. Keywords: Batch flotation, QEMSCAN, collectors, PGE and BMS

Jan 1, 2020

The vast majority of the roughly 100 million rock anchors installed in mines in the USA each year use resin cartridges1. About 4.5 million of these bolts are installed using a mechanical shell in addition to the resin to create an active (pre-tensioned) bolt. Over 1 million of the bolts are passive cable bolts and typically have an effective grout length of 1.2 m, regardless of the cable length, which could be as long as 6 m. The successful performance of the resin grouted bolts depends on several parameters, including the annular gap between the bolt and hole wall, which should be relatively small, ideally from 3 mm to 5 mm. This requirement, combined with the high viscosity of the resin, produces a high back-pressure that can cause the bolt being installed to buckle or not be installed to standard. It is this back-pressure that limits the effective grout length with passive cable bolts and causes the mechanically anchored bolt failures (typically called ?spinners? where the mechanical shell does not anchor). This creates potentially unsafe conditions and wastes time and money. A purpose, built rig was used to mimic underground installations and record the back-pressures during full scale applications in the laboratory. This information was used, and is still being used, to reduce the failures and sub-standard installations by producing improved designs. In addition, a flow model was calibrated that can act qualitatively to estimate the back-pressures and can be used as a crude screening process before full scale prototypes are built and tested. To date, the results obtained have been used to stop the use of a mechanical shell due to the proven higher rate of failures. A new, improved mechanical shell is being field tested and another system is underdevelopment. The use of the rig is therefore ongoing to develop improved mechanical anchor systems. It is too early for real data; however, anecdotal evidence seems to indicate that significant improvements can and will be made.

Jan 1, 2011

By K. Barani, S. M. S. Ganji

Creatine was used as a lixiviant for gold dissolution from gold ore. The effects of creatine concentration, temperature, leach time, and pH were examined for their influence on extent of gold dissolution. The results show that at a temperature of 75°C and pH 11.5, gold dissolution increased from 51% to 88% on increasing creatine concentration from 25 to 50 g/t. Further increase in creatine concentration showed a negative effect on the gold dissolution. Gold dissolution increased from 47% to 87% by increasing the temperature from 25°C to 55°C, and from 61% to 89% by increasing pH from 10 to 11.5. Under the optimum conditions of solids’ content of 30%, pH 11.5, creatine concentration of 100 g/t, temperature of 75°C, and hydrogen peroxide addition of 2%, about 90% of the gold could be dissolved from the ore after 24 h. A comparison between creatine and cyanide leaching showed that 90% gold dissolution was achieved at a cyanide concentration of 300 g/t, which is three times higher than the creatine concentration under optimal conditions.

Apr 14, 2024

By R. K. W. Merkle, F. A. S. Reyneke, Z. Harris, P. W. J. Delport

The technological advancements in computing power in the last 30 years have enabled the practical visualization of complex geological environments in three-dimensional (3D) space. 3D models and their application in the mining industry are becoming increasingly important, for example, to identify future exploration areas and targets, for mineral assessment and evaluation, and prediction and planning of future drill-holes. However, acquiring borehole data is an expensive practice, with drilling programmes costing mining companies up to billions of dollars each year. Tighter financial constraints on exploration budgets result in more pressure being put on three-dimensional models to accurately identify future target areas. This article aims to evaluate the potential drilling success of simulated greenfield and brownfield exploration using a 3D geological model created of Leeuwpoort tin mine. These simulations investigate the probability of intersecting a mineralized zone of economic interest and evaluate how the probability is affected when the number of drill-holes and distance from a known intersection changes. Furthermore, these simulations attempt to obtain an indication for the minimum number of drill-holes required for a successful exploration campaign at the mine. The investigation also aims to establish a first-pass attempt towards developing a ‘favoured procedure’ for identifying potential exploration targets for tin deposits with geological and geochemical characteristics similar to Leeuwpoort. The results for the ‘favoured procedure’ established are statistically tested using the ‘bootstrapping’ method. By simulating various exploration scenarios, the study also emphasises the importance of predicting successful drilling, which aids in budgeting for drilling programmes as the minimum number of drillholes needed for a specific exploration project can be determined.

Feb 2, 2022

By M. Abdellatif

"SynopsisCalcined basic nickel carbonate (BNC) concentrate was smelted in a pilotscale DC arc furnace to produce a nickel metal. The furnace was continuously operated for 12 days (24 hour/day), during which twelve different smelting conditions were investigated, with the major variables being reductant type and feed rate, flux composition and addition, and BNC feed rate.The 200 kW DC arc furnace was operated at power levels between 110 and 165 kW and at a total feed rate of 78 to 96 kg/h, resulting in an average slag and metal tapping temperature of about 1650°C. A total of 7.2 t of BNC were smelted, producing about 5.44 t of nickel metal and 2.94 t of slag. Nickel recoveries of 96.4% and higher were achieved, and the slag nickel content was as low as 0.1%. The major impurities in the metal were iron (mostly from oxygen lancing) and carbon. The calculated feed carry-over was less than 0.85% and the graphite electrode consumption was between 2.8–3.3 kg/MWh.IntroductionOne of the most distinctive advantages of DC open-arc smelting is the ability to process fine raw materials without any major issues with regard to the operability of the furnace, metal recovery, and metal quality. This has been demonstrated in Mintek’s DC arc pilot plant facilities over a period of about three decades (Curr et al., 1983). The materials that have been processed include laterite (Kotze, 2002), chromite fines (Curr et al., 1983), manganese fines (Lagendijk et al., 2010), PGM concentrates (Shaw et al., 2013), electric arc furnace (EAF) dust (Denton et al., 2005; Abdellatif, 2002a) and stainless steel (SS) dust (Denton et al., 2005; Abdellatif, 2002a; Goff and Denton, 2004), and petroleum fly ash (Abdellatif, 2002b). The top particle size of such materials can vary from a few millimetres (e.g. laterite) to micrometres (EAF and SS dust). Dusting, whether due to physical carryover of feed or to the arc side reactions, has been proven to be a non-issue. As such, the applications of DC open-arc furnaces have the potential to be extended to other raw materials such as particulate nickel oxide, which has a particle size much less than 100 µm.Nickel oxide is typically produced from laterite ore by sulphuric acid leaching, purification, and precipitation as basic nickel carbonate (BNC) (Rhamdhani, Jak, and Hayes, 2008) or as mixed hydroxide precipitate (MHP) (Mackenzie, Virnig, and Feather, 2006), and finally calcining at moderate temperatures (800–1200°C). The NiO product is very fine, with an average particle size in the range of 10–20 µm and a NiO content of more than 99%."

Jan 1, 2015

By A. Fouchee, N. Naudé, K. Schommarz

"This article presents laboratory test work conducted on an African haematite ore to determine the influence of the flotation pulp pH on the final iron grade and recovery. Results show that a combination of an isodecyl ether propylene amine/amino acetate and 1,3-propanediamine, N-(3-(C10-C16-alkyloxy)propyl)-derivatives collector is suitable for separating haematite from quartz. Higher iron grades were obtained at pH levels between neutral and pH 9. This underlines the importance of the surface charge effect of the ore on its flotation characteristics. The results serve as good baseline conditions for further optimization. IntroductionBeneficiation of iron ore by flotation is widely used in Brazil, India and China. In Africa, however, this practice is not yet commercially developed.The aim of this test work is to serve as a starting point by establishing suitable pH conditions for the development of a practically implementable reagent suite, which will then be included in a larger beneficiation circuit for producing high-grade iron ore sinter feed.In the literature, African iron ore types are graded as low-grade (60.0–62.9% Fe; 8.6– 12.5% SiO2 and insolubles), high-grade (66.0– 69.9% Fe; 0.8–4.5% SiO2 and insolubles), and meduim-grade as the remaining portion (Astrup et al., 1998). The low-grade ore used in this work contains less than 60% Fe.For Brazilian ores consisting of a combination of haematite and quartz, it is common to use corn starch as a depressant and ether amine blends as collectors with additional frothing characteristic (Araujo et al., 2005). Work by Turrer and Peres (2010) shows the possibility of using other depressants successfully as well.The main mechanism of the reverse flotation of quartz from iron ore is based on the electrostatic theory of flotation. This is due to the strong pH dependence of the zeta potential of the mineral edge planes on silicate particles (Fuerstenau and Pradip. 2005)."

Jan 1, 2016

By A. Adeli, A. V. Metcalfe, E. Addo, E. Sepulveda

"The accurate modelling of geometallurgical data can significantly improve decision-making and help optimize mining operations. This case study compares models for predicting copper recovery from three indirect test measurements that are typically available, to avoid the cost of direct measurement of recovery. Geometallurgical data from 930 drill core samples, with an average length of 19 m, from an orebody in South America have been analysed. The data includes copper recovery and the results of three other tests: Bond mill index test; resistance to abrasion and breakage index; and semi-autogenous grinding power index test. A genetic algorithm is used to impute missing data at some locations so as to make use of all 930 samples. The distribution of the variables is modelled with D-vine copula and predictions of copper recovery are compared with those from regressions fitted by ordinary least squares and generalized least squares. The D-vine copula model had the least mean absolute error. IntroductionIn this paper we compare the use of D-vine copula, generalized least squares (GLS), and ordinary least squares (OLS) for modelling geometallurgical data from an orebody in South America. The first objective is to construct models for predicting copper recovery (Rec) from the Bond mill index test (BWi); resistance to abrasion and breakage index (A*b); and semi-autogenous grinding (SAG) power index test (Spi). This involves fitting a D-vine copula and regression models fitted by OLS and GLS. The second objective is to investigate the performance of the fitted models for predicting Rec (Willmott and Matsuura 2005).Traditional resource model approaches either ignore the mineral processing characteristics of extracted tonnages or treat processing as an independent component of a mining operation. The net present value (or any other objective) can be truly optimized only by considering the mining operation as an integrated system in which net value is defined as the end-product that the company sells. This approach requires the resource model to be extended to include all relevant rock properties and processing responses."

Mar 1, 2019

By Stuart Marsland

"Reference materials have always been important for validating and controlling analytical methods', They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry demand critical validation of all results reported. Mintek has been producing geological and semi processed ore references since the early 1970's and recently due to increase in demand other manufactures have entered the South African Market.This paper describes Analytical challenges from the customer's perspective. The customer being the metallurgist, mine geologist, environmental scientist and geologists from resource companies. Reference Materials and their appropriate use and good understanding of them can aid greatly in building confidence in the results, choosing the right Laboratory for a project, deciding which set of results arc correct and providing evidence to the customer's clients that the results obtained are the very best possible.Throughout the world there are hundreds of reference materials produced by over 80 organisations and these are mainly ores, rocks, semi processed ores, metals, and many more. Mintek is one of the top 10 producers with over 75 products. Many of these producers including Mintek and their respective standards organisations belong to the ISO REMCO committee and their respective work groups. This committee's main task is to draw up guide lines for the use, manufacturing and certifying reference materials. In South Africa a mirror committee has recently had its inaugural meeting the function is to give clear mandate to the South African representative on the main ISO REMCO committee, the South African delegate bas an opportunity to influence the contents of the guides.Tile SARM program has since the year 2000 increased its sale three fold, the question is why? There is more accountability needed in our world. That means Analytical results have to be the very best possible and risks associated to them must be well quantified. Consider that the risk of wrong results of wrong decisions made from a result is trivial to laboratory, in comparison to the laboratories customers. The consequence to a laboratory could be a loss of income or some one may lose their job. To the customer he may dig up 1000 of ton's of rock with nothing in it or worse still don't mine it when the grade is high enough. This is seriol1s money."

Jan 1, 2014

By L. Stamenov, A. Grigoryan, M. Nolte, E. Ayvazov, K. Evtiminova

Dundee Precious Metals Inc. (DPM) owns and operates the Ada Tepe gold mine and processing facility (previously referred to as the Krumovgrad Gold Project) located in south-western Bulgaria. The Ada Tepe mine became the first green filed project in past 40 year in Balkans and one of the few in Europe when it was commissioned during the first half of 2019. The plant produces a high-grade gold silicate concentrate generated through its comminution circuit and staged floatation reactors (SFR’s) while depositing its tailings in a state-of-the-art Integrated Mine Waste Facility (IMWF). This paper presents the successful commissioning, ramp-up and optimization of the Ada Tepe processing plant and how the various challenges, including that of an inexperienced front-line workforce, were overcome. More specifically addressing how the implemented modern processing technologies and the operational readiness program, supported the people and process to achieve the design parameters safely and consistently. Keywords: Commissioning, Optimization, Innovation, Gold mine, Digital mine

Jan 1, 2020

By H. Schunnesson, H. Fredriksson, D. Johansson, E. Söderström, S. Manzoor, A. Gustafson, M. Danielsson

Fragmentation analysis is an essential part of the optimization process in any mining operation. The costs of loading, hauling, and crushing the rock are strongly influenced by the size distribution of the blasted rock. Several direct and indirect methods are used to analyse or predict fragmentation, but none is entirely applicable to fragmentation assessment in sublevel caving mines, mainly because of the limitations imposed by the underground environment and the lack of all the required data to adequately describe the rock mass. Over the past few years, measurement while drilling (MWD) data has emerged as a potential tool to provide more information about the in-situ rock mass. This research investigated if MWD can be used to predict rock fragmentation in sublevel caving. The MWD data obtained from a sublevel caving mine in northern Sweden were used to find the relationship between rock fragmentation and the nature of the rock mass. The loading operation of the mine was filmed for more than 12 months to capture images of loaded load-haul-dump (LHD) buckets. The blasted material in those buckets was classified into four categories based on the median particle size (X50). The results showed a stronger correlation for fine and medium fragmented material with rock type (MWD data) than coarser material. The paper presents a model for prediction of fragmentation, which concludes that it is possible to use MWD data for fragmentation prediction.

Mar 2, 2022

By D. Kumar, B. Rai, S. G. Srinivasan, V. Jain

Chalcopyrite and pyrite are among the major gold bearing minerals in the world. The gold content in chalcopyrite and pyrite varies from 0.02 to 200 ppm and 0.01 to 20 ppm, respectively. Apart from gold, chalcopyrite is also the primary source of copper. Thus, the recovery of gold and copper are often associated with the recovery of chalcopyrite and pyrite. Flotation is one of the most successful methods applied to beneficiate chalcopyrite and pyrite. The success of a flotation process depends on an appropriate choice of the flotation collector used to achieve the desired selectivity. A thorough understanding of the atomic structure of the predominantly exposed mineral surfaces can immensely aid in developing highly selective collectors that can exploit both the physical and chemical characteristics of these surfaces. In the present study, density functional theory calculations within the plane wave framework are used to understand the surface structure and reconstruction of the most stable chalcopyrite (001), (100), (110) and (112) and most stable pyrite (100) surfaces. The chalcopyrite (001) and (100) metal-terminated surfaces undergo significant reconstruction and result in metal-metal bond formation in the sub-surface layer while the surface layer is replaced by S-atoms. On the other hand, the (001) and (100) S-terminated surfaces show S—S disulfide bond formation upon relaxation, which are consistent with literature reports. The chalcopyrite (110), (112) surfaces and pyrite (100) surface undergo rearrangement, but no reconstructions in terms of metal-metal or disulfide bond formation are observed on these surfaces. Keywords: DFT, surface reconstruction, pyrite, chalcopyrite, adsorption

Jan 1, 2020

By M. Arlandi-Rodríguez, and A. García-Berrocal, A. Alonso-Jiménez, C. Lopez-Jimeno

Spain is a major producer of dimension stone, which is one of the most important industrial sectors in the northwest of Spain. This justifies the maintenance of these industries, although the technical and environmental requirements for their continuity are increasingly demanding. The main target of this paper is to present a new methodology in order to obtain k-ratio stress values on the basis of flat jack measurements and finite element numerical back- analysis with Rocscience© RS2 software. Continuous iterations were performed to try to find a relationship between the k₀ and the measured stress in the tunnel roof and sidewalls. It focuses on technical aspects of the method for designing mine chambers in the slate industry that were previously mined by open pit methods. The size of the chambers impacts the operating cost, and the dimensioning of a correct support ensures better efficiency and safety. Correct knowledge of the k₀ therefore is critical for the design of the support. The proposed new method entails a simplification of the classical procedure for estimating the k-ratio.

Sep 1, 2022

By J. W. van der Merwe, A. M. Maleka, V. J. Matjeke

The 10.5–12.5% chromium, titanium-stabilized ferritic stainless steel (FSS) plates used to fabricate coal line jumbo wagons is susceptible to undesirable chromium depletion during welding with 309L electrodes. In this work, non-stabilized FSS plates were welded using 308L welding electrodes. The objective was to weld non-stabilized FSSs using gas-shielded metal arc welding without causing sensitization. The welding process was optimized by lowering the heat input. Sensitization was assessed by rigorous etching techniques and anodic polarization scans. In addition, the welds were subjected to tensile testing, and their fracture surfaces were examined for intergranular cracking. Non-stabilized FSS plates were successfully welded using gas metal arc welding.

Apr 5, 2023

By H. S. Sichel

This study deals with the development of some new theory concerning the bias which will result from the employment of the t-estimator if in fact the underlying distribution of ore values is not lognormal. It is found that the t-estimator is robust as long as the logarithmic variance is small and the shape factors of the transformed distribution are not unduly large. The choice of the threshold parameter [t] for the t-estimator is important, and some hints are given how to estimate it if the sample size is small, as en- countered in borehole valuation problems.

Jan 1, 1987

By J. G. M. Mukoya, B. Adebayo

"This work was carried out to determine the influence of rock properties and drilling machine parameters on the penetration rate at the SJ pit of Rössing Uranium Mine, Namibia. Rock properties (uniaxial compressive strength, tensile strength, and modulus of elasticity) of samples collected were determined in the laboratory. Drilling experiments were conducted in which feed pressure, air pressure, rotary speed, weight on the bit, and torque were varied to measure their effect on the penetration rate. The uniaxial compressive strength varied from 90–180 MPa for layered marble-quartzite and banded gneiss. Increases in feed pressure, weight on the bit, and rotary speed beyond the optimum level led to a decrease in penetration rate and caused the drill bit to ‘stall’. Results of the study revealed that penetration rate increases with an increase in the feed pressure and air pressure. After reaching a maximum value, the penetration rate begins to decrease despite increasing feed pressure. A very high torque causes the drill bit to stall, since the feed pressure is too high and the air pressure is not sufficient to remove the cuttings from blast-hole at maxium bailing velocities. The average penetration rate varied from 19 to 45 m/h for phase 2 of the pit, and from 17 to 68 m/h for phase 3. The optimum drilling machine parameters obtained in phase 2 and phase 3 were slightly lower than those currently being used at the mine. The trials of the optimum machine parameters will assist in reducing the cost of drilling, which varied from N$29.48 to N$36.31 per metre for the tricone bit. IntroductionDrilling and blasting contribute most to the operational cost in opencast mining and have the potential to influence the cost of downstream operations (Aipanda, 2011). The drillability of rocks depends not only on the rock properties, but also on the drilling tools and operational variables. In rotary drilling, rotational speed, thrust, and flushing are the operational variables, and are known as the controllable parameters. Rock properties and geological conditions are the uncontrollable parameters. Although, many attempts have been made to correlate drillability with rock properties, the rock characteristics affecting rotary drilling have not been entirely defined (Hartman, 1962; Kahraman, Bilgin, and Feridunoglu, 2003). The drill bit is forced into a rock surface from the rotary power head, hence creating stresses and cracks at the bit-rock interface. The performance of a particular bit in any formation i"

May 1, 2019