Search Documents

By Albert W. Deurbrouck

The performance characteristics of five hydrocyclone coal washers were evaluated to determine the sharpness and efficiency of separation that might be anticipated in commercial operation. The hydrocyclone overflows contained generally good clean coal products that would require little re-treating to remove misplaced high-gravity material. The underflows, however, contained from 63.6 to 36.7 percent of misplaced low-gravity material, which would require secondary cleaning to provide acceptable clean coal yields.

Jan 1, 1974

By J. W. Howland

A demonstration of dozer blades, designed for recontouring area-mined spoil and shown effective at Kansas and East Texas surface mine sites, was conducted at a Northeast Arizona surface coal mine to determine their effectiveness in different climate and soil conditions. The specialized tools were: 48-ft angle blade (on side-by-side tractor), 24-ft grading bar, modified 24-ft "U" blade (on side-by-side tractor), and a 13-ft deep "U" blade. Interest in the increased dirt-handling capacity of a previously built 22-ft blade, resulted in the design of a new Centerflow Blade of good versatility, able to maintain increased flow in otherwise difficult-to-move spoil. The demonstration involved 263 acres and showed a reduction of 50% in reclamation costs and 20% in fuel requirements for this mine site over conventional equipment. This savings resulted from improved technology, trained operators, and rigorous application of supervisory and monitoring techniques. Procedures and results of the demonstration are presented and analyzed here, along with guidelines for application of findings.

Jan 1, 1982

By J. R. Thoenen

Profits in the crushed-stone industry, as in any other, represent the difference between selling price and production cost. When consumer demand increases rapidly, as occurred in the crushed-stone industry from 1918 to 1927, selling prices tend to rise. Cost of production usually rises, also, owing to the expense of expanding facilities, searching for and developing new quarries, and purchasing, installing, and operating new equipment. Frequently, also, the inattention of managements to the details of operating costs is responsible for their increase. This is not due to negligence but rather to the necessity of confining attention to the problems involved in producing material to supply orders. When market conditions change and consumer demand becomes stabilized or contracts, the producer r s attention usually is directed to assuring the orders necessary to keep his enlarged facilities busy. Hence, competition increases and soiling prices decline.

Jan 1, 1939

By Neldon L. Jensen

Although ASARCO Incorporated, the only domestic producer, had terminated copper smelting operations and associated recovery of byproduct arsenic trioxide at Tacoma, WA, in 1985, it shipped small quantities of both trioxide and metal from its remaining stocks in 1986. Imports for consumption of arsenic trioxide increased significantly, owing to increased demand for arsenical wood preservatives and the decrease in domestic shipments of trioxide. Prices remained unchanged throughout the year. Development of gallium arsenide integrated circuits, important in advanced military and commercial electronics circuitry, continued to gain momentum during 1986. Domestic Data Coverage.-Shipments of small amounts of arsenic trioxide and metal from remaining stocks by Asarco were reported voluntarily to the Bureau of Mines.

Jan 1, 1988

By J. R. Thoenen

Profits in the crushed-stone industry, as in any other, represent the difference between selling price and production cost. When consumer demand increases rapidly, as occurred in the crushed-stone industry from 1918 to 1927, selling prices tend to rise. Cost of production usually rises, also, owing to the expense of expanding facilities, searching for and developing new quarries, and purchasing, installing, and operating new equipment. Frequently, also, the inattention of managements to the details of operating costs is responsible for their increase. This is not due to negligence but rather to the necessity of confining attention to the problems involved in producing material to supply orders. When market conditions change and consumer demand becomes stabilized or contracts, the producer's attention usually is directed to assuring the orders necessary to keep his enlarged facilities busy. Hence, competition increases and soiling prices decline.

Jan 1, 1939

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By Robert A. Jankowski, J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200- to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By C. G. Maier

Relatively infrequent use by metallurgists of the term "sponge chromium" as contrasted to more than occasional reference to "sponge iron" may be ascribed to the fact that the former material is not a commercial product, while the latter has been known and used, at least in one form (Swedish sponge iron), for several decades. It is doubtful whether a true sponge chromium ever has been prepared heretofore in the laboratory by more than one or two investigators. Nature presents a much. more difficult problem to the investigator endeavoring to make sponge chromium than pertains to the production of more easily reducible elements such as iron or nickel. Recent widespread interest among metallurgists in the possibilities of powder metallurgy is ample incentive to explore the feasibility of producing pure chromium metal in finely divided form. The shift in terminology of this statement from "sponge" to the "finely divided form" is deliberate in emphasis of distinction between terms that occasionally have been used loosely. It would seem desirable that a uniform usage descriptive of finely divided metals be adopted. While to some it might seem preferable that the terra "powdered" metal be reserved for a finely divided form produced by mechanical means, as, for example, chromium produced by the mechanical comminution of electrolytic sheets or flakes, current usage of the term "powder metallurgy' involves no distinction as to source type of material. It is usually accepted, however, that a sponge metal is one reduced from oxide or other combined form at temperatures below the melting point of metal or oxide so that the particles of metal are pseudomorphic, at least macroscopically, with the source material, and, in consequence of the loss of material without change of external shape of the particles necessarily have an open, porous, or "spongy" structure.

Jan 1, 1942

By M. P. Hardy

Copper-Nickel ores in northeastern Minnesota could establish a new industry in a region where underground mining has not been active. This study reviews geotechnical data relevant to the selection and design of underground mines in this region and by numerical structural analysis evaluates the importance of some geotechnical parameters to mine method selection. Because of the rapid development of computer modeling many new techniques have become available for modeling rock mass behavior in recent years. An overview of these methods is presented and their applicability to mine design reviewed. Methods included in this summary were the differential continuum models, such as finite Pint and finite difference, integral continuum models, such as boundary element, displacement discontinuity and boundary integral equation methods, and discontinuum methods such as the distinct block model. The displacement discontinuity method was used to evaluate the influence of geotechnical parameters on some aspects of mine design. Three problems; room stability, pillar stability on a weak inclined contact and sill pillar thickness influence on sill pillar stability, were analyzed to evaluate the relative importance of insitu stress field and joint properties on design. It was concluded that for stability analysis the initial horizontal stress is of most importance in all aspects of design. The position, orientation, persistence and strength of joints is also of primary concern. In a more general sense, however, it was concluded that detailed geotechnical parameters have much less influence on mine method selection than more general factors such as rock quality, initial stress state, orebody shape and economics.

Jan 1, 1978

By Nick Barton

When the Q-system was launched in 1974, the name referred to rock mass classification, with focus on tunnel and cavern support selection. Besides empirical design of support, the Q-value, or its normalized value Qc, has been found to correlate with seismic P-wave velocity, with deformation modulus, and with deformation. The Q-system provides temporary or permanent support for road, rail, and mine roadway tunnels and for caverns for various uses. It also gives relative cost and time for tunnel construction for a complete range of rock qualities. There are also indications that Q has captured important elements of the cohesive and frictional strength of rock masses, with Qc resembling the product of rock mass cohesion and rock mass friction coefficient.

Jan 5, 2007

By Yael Miron

This report describes laboratory studies by the U.S. Bureau of Mines to determine the suitability of a static oxygen (OJ adsorption test for evaluating the self-heating tendencies of coals. Reliable minimum self-heating temperature (SHT) values from adiabatic oven tests were used as standards for comparison and evaluation. A suite of six coals was tested in the adiabatic oven and in sealed flasks. In the latter tests, both undried and dried samples, in a range of four particle sizes, were examined. Miniature pressure trans-ducers monitored pressures in the flasks, and gas samples taken at the end of the tests quantified all the gases present. An excellent correlation was found between the minimum SHT's and amounts of O2 adsorbed over a 7-day period for dried coals, independent of particle size. In addition, a good correlation was obtained between the minimum SHT's and pressure changes in the flasks at the end of the test for the same coals, also independent of particle size. Based on these results, the sealed flask test can be reliably used to determine the self-heating tendency of a bituminous coal sample.

Jan 1, 1990

By John L. Ellenberger, Gabriel S. Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

By F. E. Cash

"Explosions in bituminous coal mines are preventable. The combination of adequate ventilation, thorough rock-dusting, and water on the cutter bars of mining machines and of empty and loaded cars will certainly reduce the hazard to a minimum, if not remove it entirely. This is the attitude taken by the Woodward Iron Co. in lessening or removing the dust and gas explosion hazard from its Dolomite and Mulga mines.This report was made possible through the willingness of Frank H. Crockard, president of the Woodward Iron Co. to make records available and to authorize their publication for the benefit of the coal-mining industry.The compilation of these data and preparation of maps was facilitated by the cooperation of M. Heard, general superintendent of coal mines, J. B. Whatley, assistant general super-intendent of coal, and R. P. Whetmore, chief mining engineer.The Dolomite and Mulga mines are about 16 miles southwest of Birmingham, Jefferson County, Ala., on a company owned and operated railroad which connects ore mines, coal mines, coke ovens, and furnaces.In the Dolomite property there is a 30°, 860-foot, double-tracked slope for hoisting, three manway and air slopes and one air shaft, all in rock.At Mulga there is a 220-foot hoisting shaft, an air shaft and two manways, and material and air slopes, all in rock to the coal bed.The coal in both mines comes from the Pratt bed, which is the next coal above the Mary Lee bed in the Warrior Basin. The coal is horizontal or slightly undulating, with thickness varying from 36 to 72 inches and averaging 50 inches.The method of mining is essentially room-and-pillar with modifications for mechanized sections. The mines produced approximately 1,100,000 tons with 2,328,309 man-hours exposure n 1929 and 900,000 tons with 1,697,436 man-hours exposure in 1930.Through the work of the safety department the entire personnel in the coal mines, as well as in other departments, makes safety an essential part of efficient operation.Both mines are gassy; Dolomite produces about 334,000 cubic feet and Mulga about 919,000 cubic feet of methane every 24 hours.The ventilation maps, two of Dolomite mines (figs. 1 and 2) and one of Mulga (fig. 3) give as much of the details of ventilation as is practicable to put on maps of such scale. As will be seen from these maps there are two main ventilating fans in Dolomite mine and two in Mulga mine and the general direction of the air travel is indicated by long arrows to fan 1 and short arrows to fan 2 in each mine. Each fan has a gas or steam auxiliary drive and each mine has a complete fan and power unit ready for operation in emergency.In Dolomite, recently taken data show that fan 1 exhausts 82,000 cubic feet of air per minute at 3.2-inch water-gage pressure, with an analyzed methane content of 0.15 per cent, and fan 2 exhausts 115,500 cubic feet of air at 3.8-inch pressure and 0.10 per cent of methane. In addition, a Capell fan at No. 2 air shaft is a standby or emergency unit.In Mulga recently taken data show that fan 1 exhausts 83,000 cubic feet of air per minute at 3.0-inch pressure and 0.18 per cent of methane, and fan 3 exhaust 119,000 cubic feet of air per minute at 5.4 inch pressure and 0.35 per cent of methane. Fan 2 at No. 2 shaft is a standby or emergency unit for the Mulga mine.The ventilation is on a split system in both mines. All part split and total returns are measured, sampled, and analyzed weekly, requiring one man two days each week. During December, 1930, 77 samples were collected and analyzed in Mulga and 78 in Dolomite. Two weekly reports covering part of December, 1930, are given here so that they can be studied to show control of ventilation in the Dolomite and Mulga mines. In the event that a split sample shows more than 0.50 per cent of methane, immediate steps are taken to lower the explosive-gas content. The reports follow:"

Mar 1, 1932

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchange-ability, and speed, it has become even more important. In spite of the supply of other abrasive and hard materials and of ultrasonic, electrospark rued other substitute grinding, methods, world industry seams likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting roes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determined the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has affected substantial savings.]

Jan 1, 1964

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchangeability, and speed, it has become even hors, important in spite of the supply of other abrasive and hard materials and of ultrasonic, electrospspark rued other substitute grinding methods world industry seems likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting goes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determine the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has effected substantial savings.]

Jan 1, 1964

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

By J. P. Schmid

Results of a comprehensive investigation of the impact of underground mine waste disposal on the health and safety of miners are presented. Information was gathered through an extensive search of American and foreign literature and personal communication with professionals in private industry and government. All conceivable health and safety hazards directly or indirectly related to underground mine waste disposal are analyzed, catagorized, and ranked on an industry-wide basis. Positive health and safety effects are analyzed and ranked in a similar way. Both potential and known hazards and positive impacts are included. Recommendations on abatement techniques for the various hazards are presented. Case histories of a fill-related accident in a metal mine and a health hazard associated wtih coal waste backfilling are included and causes and possible abatement procedures are discussed. The rule of management in the promotion of health and safety in backfilling operation is discussed.

Jan 1, 1982

By Linneas Laage, Thomas Weber, William Pomroy

"Underground mine fires can significantly influence mine ventilation airstreams, in some cases throttling or even reversing airflows. As a result, the performance of a metal and nonmetal mine stench fire warning system, which depends on the ventilation to carry the vital warning signal, under fire conditions is different from performance under nonfire conditions. The safety of underground miners can be jeopardized if the warning signal is delayed. This Bureau of Mines report describes research to investigate fire and stench warning system interactions. A computer model is presented that permits quantitative analysis of stench warning signal delays as a function of fire location and intensity. The results of a case study involving computer simulations of stench distribution in a hypothetical mine network subject to various fire exposures are also discussed. This case study illustrates a technique for identifying the areas within a mine that are subject to unacceptable warning signal delays, thereby enabling preemptive action by mine personnel, such as redeployment of stench injectors. INTRODUCTIONFires are an ever-present threat to the safety of underground miners. Since the smoke and toxic gas produced by a mine fire can be spread rapidly by the mine's ventilation system, mine evacuation must be accomplished as quickly as possible in the event of fire. In metal and nonmetal mines, the most common means of passing the fire warning signal to each miner is the stench system. The typical stench system utilizes ethyl mercaptan, a highly odoriferous organic compound, injected on the surface into the compressed and/or ventilation airstreams. Upon smelling the stench, workers evacuate the mine according to an emergency preplan.Although the stench system has been used successfully for over 60 yr, it has several serious shortcomings, owing to certain chemical properties of ethyl mercaptan and to certain performance characteristics and limitations of present injection systems.Recent Bureau research succeeded in upgrading the overall safety and effectiveness of the stench system through the use of a superior stench odorant and the development of improved stench injection equipment (1).4 This research has also investigated a specialized computer simulation model capable of calculating the precise concentration of stench in any mine ventilation network branch at any time after stench release (2). An adaptation of the computer model now enables the analysis of stench system and ventilation system interactions under the influence of a mine fire."

Jan 1, 1987

By R. W. Van Dolah

A premature detonation of an explosive charge occurred on January 30, 1961, at a face being prepared for blasting in the underground Jefferson Island Salt Mine, Diamond Crystal Salt Co., Jefferson Island, Iberia Parish, La. The accidental blast injured the powderman fatally; his helper was injured also, but recovered. The accident represents the first fatality reported to the Bureau of Mines in connection with the use of ammonium nitrate-fuel oil (AN-FO) blasting agents in underground mining in the United States. Representatives of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activity conducted the investigation, upon request of the manufacturer of the ammonium nitrate being used and with concurrence by the mine management.

Jan 1, 1962