Search Documents

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine's roof. This report was prepared by the U.S. Bureau of Mines to summarize the opinions of 268 coal miners, 29 rust-line supervisors, and 30 MSHA inspectors concerning why people go under unsupported roof, and how to prevent this behavior. Interviews were conducted at six minesites.

Jan 1, 1991

By David C. Byrne

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupation-al Research Agenda, problems created by occupational hearing loss include(1) reduced quality of life due to social isolation and unrelenting tinnitus,(2) impaired communication with family members, the public, and coworkers, (3) diminished ability to monitor the work environment (i.e., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers’ compensation and hearing aids. Although eliminating hazardous noise is the long-term solution to the noise problem, miners will likely need to rely on personal hearing protection in certain situations for quite some time. However, it is well known that noise attenuation provided by hearing protectors as they are worn during everyday use is usually quite different (i.e., worse) than when tested under lab conditions. In addition, workers may refuse to wear their hearing protection for any number of reasons. This project was initiated to evaluate practical technological advances in hearing protectors, with an emphasis on optimizing the balance between effectiveness, comfort, over protection, and communication ability. The recently completed auditory research facility is now under-going the accreditation process conducted by the National Institute of Standards and Technology under the National Voluntary Laboratory Accreditation Program. Experiments are planned to investigate the factors that affect a miner’s ability to hear hazard and warning sounds (e.g., roof working, alarm signals, spoken communications, etc.). A service contract has been initiated to record and digitally store samples of typical warning sounds heard in an underground coal mine. This information will be analyzed in the lab to develop recommendations that can be offered to the mining community regarding correct earplug/earmuff usage to maximize there cognition of hazard and warning sounds while adequately protecting the miners’ hearing.

Jan 12, 2001

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By J. A. Gutierrez-Rodriguez, R. J. Purcell, F. F. ApIan

"Based on contact-angle measurements and the work of adhesion equation, the hydrophobicity of a wide variety of coals was found to decrease with decreasing rank, fixed carbon and total carbon content and with increasing oxygen and hydroxyl content. The estimated hydrophobicity, based on the water-sessile-drop contact angle, is '\.. 20% for lignite, increases with increasing rank up to a maximum of 'V70% for low (LV) and medium (MV) volatile bituminous coals and then decreases somewhat for anthracite. Using the captive-bubble technique, the calculated hydrophobicity ranges from '\.. 0% (below HV A bituminous rank) to a maximum of 55% for L V-MV coal. The former estimation is believed to be the more accurate. While the water-sessile-drop contact angle as measured on a polished-coal surface is usually larger than that shown by the captive-bubble method, the two values were found to converge at""' 95% relative humidity. It is proposed that the surface of coal consists of three kinds of sites: strongly hydrophobic, weakly hydrophobic and hydrophilic. The sessile-drop technique measures the total hydrophobic sites whereas the captive-bubble method measures only the more strongly hydrophobic sites. A water film covers the weakly hydrophobic sites preventing their detection by the captive-bubble technique.INTRODUCTIONCoal is a mixture of the degradation products of plants and of mineral matter. The appearance and properties of a specific coal is determined by the nature of the original vegetation and the extent of the physical and chemical changes which have occurred after deposition. The coalification process may be considered to have started with peat formation followed by a transition to lignite due to burial under sediments and metamorphic processes. Further metamorphic transformation to bituminous coals and, finally, under intense metamorphic action, to anthracite causes the carbon content and rank of the coal to increase. With such a wide variation in their genesis and composition, equally wide variations in the degree of hydrophobicity of different coals may be expected. It is the purpose of this paper to provide a means of estimating the hydrophobicity of a given coal sample based on rank parameters."

Jan 1, 1989

By J. J. Forbes

First - aid training is an essential part of safety programs in the mining industry , but it is only a means to an end ; first -aid training will not eliminate accidents , but unquestionably it is of considerable value in any accident prevention program . Numerous features should be incorporated in any efficient , well - developed safety plan ; in addition to first -aid training safety work , to be reasonably effective , should include the establishment and maintenance of a safety organization , safety competitions between mines or sections of mines , safety- inspection committees , accident - investigation committees , safety meetings of mine officials , safety bulletins and posters , employees ' safety publications , Holmes Safety Chapters (which provide for monthly safety meetings of all employees ) , and numerous other activities looking to safe operation of mine or plant . These features are supplementary to the fundamentals of safety-- adequate and effective supervision and discipline . Years of experience , however , have demonstrated that first - aid training is a good accident -prevention auxiliary and should be made an integral part of every company's safety program . Many safety-organization plans have failed because they have been based upon the assumption that the supervisory force should be given full authority and responsibility for achieving safety and eliminating accidents and that the workers , who are most vitally concerned , are nonessential . First -aid training causes the employees to feel that they have a personal and full participation in the safety program and is now available so readily that no individual or organization has any valid excuse for not having it . Early investigations made with a view to bettering health and safety conditions among the employees in the mineral industries demonstrated the need of prompt care of injured employees because , under the difficulties inherent in the occupation , seemingly unimportant wounds , when not treated promptly, became infected and caused permanent disability and even death . Many seriously injured persons , brought out of mines and plants by fellow workers who were ignorant of the approved methods of giving first aid or of safe means of transportation

Aug 1, 1934

By Henry Kreisinger, J. F. Barkley

This book is one of a series of publications being issued by the Bureau of Mines for the purpose of disseminating information in regard to the methods by which the fuels in this' country may be used most efficiently. A knowledge of the temperature of the gases in boiler settings and in other commercial apparatus using heat tends to develop improved designs of apparatus and better methods of operation, thus reducing waste of fuel. The following pages present, for the benefit of those designing, operating, and testing such apparatus, information as to the accuracy of temperature measurements made under certain conditions and the corrections that can be safely applied.

Jan 1, 1918

By M. R. Geer, H. F. Yancey

"INTRODUCTION Throughout the history of coal washing, the jig has been one of the most important coal-cleaning appliances. In 1935 34.7 percent of the 45,361,021 tons of clean coal produced was the product of jigging. 4/ Previous to 1928, most of the jigs used in the United States were of the piston type, with which sufficient mobility to allow stratification in bed is imparted by the reciprocating up-and-down movement of a piston in the water compartment adjacent to the screen compartment. In 1928, the Baum type of jig was introduces in this country and has since come into wide spread use. In this type, water pulsations are imparted by application and release of compressed air to the water compartment. All prior studies of the mechanism of seperating cleared coal from impurity by piston-type jigs. 5/ The same laws of settling, of course, apply to both types, piston or Baum, but the character of the separation with the Baum type may be modified more easily because of the flexibility with which air may be handled, as distinguished from the fixed action of eccentrics commonly used in piston jigs. Since no detailed studies are available to show the performance, that is, the character of the separation between coal and impurity, of the Baum type the Bureau of Mines undertook the investigation recorded in this report."

Jan 1, 1938

By Robert W. Waytulonis

The mining regulations of all 50 States were reviewed by the Bureau of Mines, and those parts pertaining to the use of internal combustion (IC) engines (particularly diesel engines) in underground mines or confined spaces were extracted. Also extracted were subjects associated with the use of IC engines; for example, storage and handling of flammable liquids, maintenance, and ventilation requirements. As the laws now stand, 29 States have specific regulations that affect the operation of diesel engines in underground coal and/or metal and nonmetal mines. The other States have no regulations because either they have no mining activities or they defer to Federal regulations. Six states have regulations expressly prohibiting the use of diesels in underground coal mines. Specific contacts (addresses and phone numbers) precede each State's regulations to facilitate inquiries about regulation revisions and interpretation.

Jan 1, 1981

A series of laboratory evaluations examined the impact of water spray pressure, curtain setback distance, and external and underboom spray use for controlling respirable dust levels and sulfur hexafluoride tracer gas concentrations around a continuous mining machine. This mining machine was equipped with a flooded-bed dust scrubber and was positioned in the box or slab cut. Exhaust line brattice was used for all tests. Dust levels were measured in the return airway and at locations representing the operators of the continuous mining machine and the standard and off-standard shuttle cars. Increasing water pressure or using the underboom sprays produced no significant impacts on dust levels, although their interactions did produce some significant impacts. Increasing curtain setback distance often elevated dust levels, likely by reducing the amount of airflow reaching the face. Use of the external sprays created additional airflow around the mining machine that pushed the dust cloud past the scrubber inlets. This significantly increased dust levels at all sampling locations. Tracer gas levels were measured on the off-curtain and curtain sides of the cutter head and in the return airway. Increasing water pressure generally led to significantly increased gas levels on the curtain side, although a slight decrease was observed on the off-curtain side with the machine in the box cut. Increasing setback distance elevated gas levels on both sides of the cutter head and in the return by limiting the quantity of ventilation airflow reaching the face. Use of the external sprays provided additional airflow along the off-curtain side of the machine, significantly reducing gas levels in this region. These sprays adversely impacted the dilution and removal of gas on the curtain side of the cutter head. Use of the underboom sprays adversely impacted gas levels on both sides of the cutter head. Use of the external sprays provided the best control of respirable dust and face gas concentrations. The smaller increases in miner operator dust levels produced by these sprays were offset by larger reductions in face gas levels on the off-curtain side of the cutter head. Although the underboom sprays minimally impacted respirable dust levels, use of these sprays was not recommended because they increased face gas levels.

Jan 1, 2007

By H. Reginald Hardy

This report is Volume II of a three volume final report dealing with the microseismic monitoring of a longwall coal mine. The research presented in Volume II is concerned with the evaluation of field techniques for obtaining seismic velocity data required for computing microseismic source locations. The report describes the evaluation of a number of different field techniques and the seismic velocity data obtained at the Greenwich mine site where the micro-seismic studies, described in Volume I of the final report, were carried out. Three different methods were employed to evaluate seismic velocities, namely; surface refraction, down-hole, and transmission. In all cases the seismic sources were either located on surface (mechanical impact) or near-surface (explosive charges). It was found that a mechanical energy source could be conveniently utilized to determine shallow velocities and make bedrock-regolith interface depth determinations. For deeper velocity determinations suitable explosive charge sources Here required. In general, refraction data did not always plot in a linear manner and some subjective interpretation was necessary. The down-hole method was found to be useful for incremental vertical velocity evaluation, however, the transmission method provided the most consistent average vertical velocity data. At the Greenwich site seismic velocities were found to be anisotropic with values ranging from 9,551 to 10,739 feet per second depending on direction.

Jan 1, 1977

Alabama ranked 19th in the Nation in nonfuel mineral value1 in 1994, down from 18th in 1993, according to the U.S. Bureau of Mines. The estimated value for 1994 was $576 million, a 2.5% increase over that of 1993. This followed a 3.5% increase in 1993 over that of 1992. The State accounted for a little less than 2% of the U.S. total. Nonfuel mineral production in Alabama consisted entirely of industrial minerals; no metals were mined in the State. Bauxite materials mined in the State are a natural mixture of bauxitic clay and bauxite having very low iron oxide content and are primarily used to make refractory (high temperature resistant) products, rather than in the production of primary aluminum. In descending order of dollar value, the top four mineral commodities produced in Alabama were crushed stone, portland cement, lime, and construction sand and gravel. These commodities accounted for almost 88 % of the State's total non fuel mineral value, while crushed stone and portland cement together represented almost 65 % of the total. In estimated mineral production for 1994, Alabama remained first in common clays and first of only two States that produced bauxite; third in lime, kaolin clays, and fire clays; seventh in portland cement and salt; and was one of the top seven States that produce bentonite clays. The State dropped from third to fifth in masonry cement. Production of talc and pyrophyllite resumed in 1994. Compared with 1993, the value of crushed stone, lime, construction sand and gravel, common clays, kaolin clays, fire clays, bauxite, and talc and pyrophyllite increased. Decreases occurred in portland cement, masonry cement, industrial sand and gravel, and dimension stone.

Jan 1, 1995

By Richard L. Unger

The Crewstation Analysis Programs (CAP) is a package of computer programs that can be used to analyze some human engineering aspects of crewstation design (such as visibility and illumination) that have particular significance in underground mining. It was developed under the U. S. Bureau of Mines (USBM) Health, Safety and Mining Technology program at the Pittsburgh Research Center, Pittsburgh, PA. This manual describes the steps necessary to collect data in the laboratory to develop luminaire profiles for the CAP illumination analysis. It also describes how the CAP Illumination Model calculates illumination. 1.1 How CAP Calculates Illumination 1.1.1 Background -CAP currently includes assessments of visibility and illumination in the surrounding work area. The advantage of using computers for these types of analyses is that many design iterations can be tested quickly and efficiently to learn the effects of changes. This reduces the need for expensive testing using physical mockups. Another advantage is that design ideas can be tested in situations where it would not normally be possible. For instance, the effects of modifications to a lighting system or canopy design on visibility could be tested while the machine remains in service.

Jan 1, 1994

By Mark K. Larson

Researchers at the U.S. Bureau of Mines have developed a FORTRAN computer program that can calculate stress states from overcoring measurements obtained from hollow inclusion cells, triaxial cells, strain gauges installed on the wall of a bored raise, doorstopper gauges, borehole deformation gauges, or a combination of any of these gauges. Such stress states are calculated with reference to global and principal coordinate systems. The background of the development of the program, its capabilities, and its special features, as well as the input required, are described in this report. Sample output is also shown in appendix C. Difficulties associated with numerical calculations of principal stresses and directions are pointed out. Threshold values for detecting these problems are reported; these values may be changed by the user as desired. Several test problems were set up to verify the computer program and were successfully solved.

Jan 1, 1992

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952

By John D. Watson

The results of extensive field tests of a new and powerful method of hard rock excavation are presented in this report.* The method, known by the acronym REAM (Rapid Excavation and Mining), employs high velocity, smooth bore cannons to efficiently deliver energy to the rock and has been demonstrated for underground tunneling, drilling, surface benching, scaling, and secondary breakage in hard granitic rock at the Hope Valley Mine test site in California. Solid projectiles made from inexpensive materials such as concrete or steel, and weighing from 8 to 12 pounds, are launched by conventional high speed cannons and impact the rock at velocities of 5000 feet per second--an impact energy of about 4 million foot pounds (Figure 1). The energy applied at peak pressures of nearly 2 million psi over a period of tens of microseconds breaks down the rock by a complex mechanism of crushing, spalling, and initiation and propagation of fractures produced by the interaction of successive impacts and free surfaces. The main objective of the tests during 1973 was a demonstration of controllability of the underground operation of a silenced cannon. To accomplish this objective a 90-mm cannon

Jan 1, 1974

By W. F. Wyman, S. F. Ravitz

"INTRODUCTION By far the greater part of the high-grade manganese ore used in the United States is imported from overseas. During the early part of the recent World War importations of manganese ore were seriously threated, and it appeared that it would be necessary to utilize low-grade domestic ores to the fullest possible extent. Among the processes that appeared to offer the best possibilities for beneficating low-grade domestic oxide manganese ores, which ordinarily are net readily amenable concentration by ore-dressing methods, were those involving leaching with sulfur dioxide. The Bureau of Mines therefore investigated the amenability of a large number of such ores to sulfur dioxide leaching.Several sulfur dioxide processes for beneficiating low-grade oxide manganese ores have been proposed. 3/ One of these, based on a patent by Van Arsdale and Maier, 4/ was used recently in a plant constructed to treat 1,000 tons per day of 20-percent manganese ore from the Three Kids deposit near Las Vegas, Nev. 5/ In this process the ore slurry is leached with sulfur dioxide gas, the resulting solution is evaporated to crystallize the manganese sulfate, the crystals are decomposed thermally to produce high-grade manganese oxide and regenerate sulfur dioxide, and the manganese oxide product is nodulized. The Bureau of Mines has recently developed a process 6/ in which a suspension of the ore in calcium dithionate solution is leached with dilute S02 gas, the manganese is recovered from the resulting solution by a simple lime precipitation, and the precipitate is nodulized or sintered to form a high-grade manga¬nese oxide product."

Jun 1, 1947

By D. K. Deardorff

The purpose of this work was to investigate the hafnium-carbon phase diagram. Alloys used to study this system were prepared from high-purity components by both consumable-and nonconsumable-electrode arc melting. Data for the diagram were obtained on the alloys by metallography, optical pyrometry, thermal analysis, heat treatment, and X-ray diffraction. The data indicate that a carbide compound occurs over considerable range of composition, and that one of each of the following types of reactions occurs in the hafnium-carbon system: Peritectoid, peritectic, and eutectic. The maximum melting temperature of hafnium carbide is 3,840° C at 49 to 50 atomic percent carbon, and the composition range of hafnium carbide at temperatures of 2,150° to 2,380° C is from 37.0 to 48.5 atomic percent carbon. The hafnium a-S transformation temperature is raised on alloying with carbon from 1,750° to 1,890° C, where a peritectoid reaction isotherm occurs. Alloying hafnium with carbon increases the hafnium melting temperature from 2,190° to 2,250° C, at which temperature a peritectic reaction occurs. Hafnium carbide and carbon react at 3,055° C to form a eutectic of 68.3 atomic percent carbon.

Jan 1, 1967

By E. D. Gardner

This paper on the square-set system of mining embodies the results of a special study of the subject made as a part of the Bureau of Mines general investigation of mining methods and costs. Data for the paper were gathered by the authors during visits to mines using square-set mining, from Information Circulars prepared by consulting engineers to the Bureau on mining methods at individual mines, and from articles in the technical press and the Transactions of the American Institute of Mining and Metallurgical Engineers. The square-set system of mining is very widely applied and is one of the oldest methods in use in the United States. It is mainly employed for extracting relatively high-grade ore in heavy ground. It is also useful in taking out pillars left in mining by other methods. It is used to some extent as an auxiliary method with many underground systems and as an alternate with cut-and-fill, shrinkage, and open-stope methods when heavy ground is encountered. In some cases as much as 50 per cent of the ore may be extracted by square-setting at mines listed as using some other method of mining. A large tonnage is mined yearly by square-setting, principally in the Western States.

Jan 1, 1933

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Jan 1, 2008

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Nov 1, 2008