Search Documents

By Robert E. Barieau

The following zero pressure thermodynamic properties of nitrogen gas are tabulated: [C°p, H° -o, S°], These properties are tabulated in units of joules, gram mole, degrees Kelvin and in calories, gram-mole, degrees Kelvin for every degree Kelvin from 50° to 550°. The same functions are also tabulated in units of British thermal units pound-mole, degrees Rankine for every degree Rankine from 100° to 1,000°.

Jan 1, 1967

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, roofing granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of roofing, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural fines available. On the other hand, California manufacturers of asphalt products other than paving utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, slate, and other nonmetallic minerals as filler, mainly for roofing and flooring. Also, about 500,000 tons of roofing granules is produced in California, most of which goes into roofing manufacture in California. In addition, a significantly large and growing tonnage of relatively coarse mineral aggregates are used on low-angle, built-up, asphalt roofs to produce an attractive surface and offer protection against the elements. Nearly all minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of these commodities could be utilized in some use categories.

Jan 1, 1966

By Wilbert J. Huff

The Explosives Division of the United States Bureau of Mines makes certain laboratory and field investigations that deal with explosions, explosives, ignition, and combustion, together with many related problems, such as the cause and prevention of fires, and certain fundamental scientific questions bearing upon the determination of the chemical and physical mechanisms underlying some of the important phenomena encountered. Its work on explosives has been particularly directed toward determination of the chemical and physical characteristics of explosives designed for use in coal mines and in a more limited way to those used in metal mines, tunnels, quarries, and other engineering operations. This testing is handled by two units of the Explosives Division, as follows:

Jan 1, 1937

By Charles G. Maier

"INTRODUCTION The use of thermodynamic calculations to answer practical problems in metallurgy, especially those that are relatively difficult to test experimentally, is rapidly becoming a conventional method of procedure. Nevertheless, these methods cannot he applied effectively until the fundamental thermodynamic constants used for them have become available either by direct experiment or by recalculation of data already existing in more or less undigested form.In an attempt to collect such data far the compounds of lead and the antimony group the incentive has been to make a preliminary survey that will disclose the gaps or questionable phases of available information and to collect data that may be used to answer certain rather practical problems presented by operating metallurgists.This report comprises three sections; the first gives the basis of selection of the constants which may now be given or estimated, and the later sections discuss the application of the figures obtained to two of the more interesting problems.The reader will discover that many of the quantities involve critical study of a number of more or less discordant observations. Although certain data could be rejected on the basis of thermodynamic comparisons, it must not be overlooked that many of the figures are the results of rational estimates rather than exact experiment. The use of thermodynamic methods to control and partly authenticate such estimates is one of its most valuable characteristics for the practising metallurgist or chemist, who cannot check by direct experiment each property of the materials which he converts to usable form.Nevertheless, while it is definitely possible in certain instances that the final figure selected for the heat or free energy of a process or substance may be in error by as much as a few hundred to a few thousand calories per formula weight, questionable figures are usually revealed by the thermodynamic calculations made. When quantities of such degree of accuracy are, and they often must be, used for estimating an unknown reaction, the result often gives no more than the order of magnitude of the desired quantities. Yet even in these extreme cases the answer is far more reliable and valuable than an unordered guess or a conclusion based on incorrect data."

Dec 1, 1934

By E. Don Dilling, W. F. Holbrook, Lloyd R. Michels, James W. Pennington, Dwight L. Harris, Wm. F. Hergert, Cyrus L. Blogett, H. A. Doerner, Ernest A. Reige

"IntroductionA process for production of magnesium by carbothermal reduction was developed at Padentheirm, Austria, by the Austro Americanische Magnesit Corporation& an independent investigation of this and other processes was started in 1937 by the Bureau of Mines at Pullman, Wash., with the cooperation of Washington State College. 10/ A preliminary study of the Radentheirm pro¬cess, as revealed by the meager information then available, demonstrated the following two major disadvantages,The use of hydrogen for shock cooling requires an enormous volume of gas - about 1,000 cubic feet for condensing each pound of metal as a pyrophoric dust which must be completely separated from this gas. Then if the gas is to be recycled for repeated use, the CO produced by the reduction reaction must be separated from the hydrogen. These separations are costly from the standpoint of equipment and operation. 11/The condensate is an impure, pyrophoric metal powder that must be purified and converted to coherent form. This is accomplished by distillation or sublimation of the metal. Distillation on a large scale involves difficulties inherent in the high boiling point (1,107° C.) and the chemical activity of the metal. To avoid these difficulties, the metal is sublimed at 600° C. and of very low pressure. This is quite easily carried out as a batch operation but is a costly procedure. A continuous sublimation process has not been accompli shed."

May 1, 1945

By R. S. Dean

"INTRODUCTION The metallurgical research program of the Bureau of Mines has been somewhat disorganized, but generally advanced by the increased activities of the war period. The present report is for the purpose of summarizing the work of the Bureau in this field for the past 15 years and indicating its future plan.Fifteen years ago the Bureau turned from its pioneer work on the physical chemistry of steelmaking to an emphasis on raking a pure steel synthetically, rather than by refining, that is, :producing each of the steel 'constituents in the pure state and combining them by simple melting. Such a procedure permits the use of less high-grade ores, not only of iron, but of the ferroalloy metals, such as manganese and chromium,This program has led to extensive work on iron-ore concentration, agglomeration, reducibility of ores and agglomerates, direct reduction of iron ores and concentrates by a wide variety of processes; special refining processes for iron, the production of pure mangenese, chromium, and cobalt from low-grade ores by electrolytic processes, the production of ferrochromium, ferronickel, and ferronickel-cobalt from low-grade domestic ores, and the development of many special alloys to effectively use the new products.The status of the work in each of these fields and the future program of work, together with a bibliography of papers and patents by the Bureau staff on each of these subjects, are given."

Jul 1, 1946

By Michael W. Redifer

A Fortran IV computer program was developed to calculate the composition at equilibrium of products from a set of high-temperature gas combustion reactions. The program was used to develop high-temperature equilibrium concentration profiles for various constituents as a function of temperature and oxygen concentration. The computer program was specifically applied to reactions pertaining to the corrosion of superheater tubes in pulverized coal-fired boilers; however, it is useful for any multicomponent, multireaction scheme in which equilibrium constant data can be obtained and is comprised of gaseous reactants along with finely dispersed solids or liquids. General applicability of the computer program, including its limitations, are discussed along with detailed instructions for using the program.

Jan 1, 1973

By Oliver Bowles

"Simple systematic accounting that adequately records all transactions has long been regarded as essential to the welfare of any business enterprise. Some of the defects that detract from the prosperity of the slate industry are attributable to a lack of effectiveness in cost keeping. This condition has prompted the United States Bureau of Mines to make a detailed study of accounting methods for the slate industry, and to present for consideration a system of accounts, which it is believed would enable the industry to attain more economical management and operation if accepted by a fair proportion of its important units.The method of accounting presented herein has been worked out with the assistance of leading slate producers and the recommendation are tentative and are submitted in this form as a means of developing constructive criticism. Believing that cooperative effort in this, as in many other problems, will bring the most enduring benefits to the industry as a whole, the writer urges that the most earnest consideration be given to this vital problem now facing the slate industry.Grateful acknowledgment is made of the helpful assistance rendered by R. E. Eckert of the accounting firm of Eckert, Degan, and Palmer of Easton, Pa., in compiling the charts and the explanatory text. He has brought to this work a wide knowledge of accountancy, supplemented by a background of direct contact with the slate industry, and his presence at the various conferences has been of great advantage in clearing up difficulties. The National Slate Association sponsored the cost study and chiefly through the efforts of President W. H. Smith and Secretary W. S. Hays, has aided greatly in conducting it. Acknowledgment is also made of assistance rendered by William F. Marsh of the United States Bureau of Mines."

Nov 1, 1929

By Walter I. Enderlin

To economically extract ore from great depths in the earth while sustaining an acceptable working environment will require the development of new technology and equipment, involving large capital expenditures. Moreover, careful analysis and advance planning will be required. But, the literature is lacking in data pertaining; to the thermal properties of various host rocks and to quantities of heat generated by various underground heat sources. This types, of data is required to forecast nine heat loads during advanced planning and design. This thesis sets forth a practical method for evaluating underground sources of heat in deep mines and provides an improved information base. Moreover, seven topics for further research are recommended. The heat sources considered are: wall-rock, ground water, adiabatic compression, equipment, service lines, blasting, metabolism, curing of cement, and oxidation of sulfides and timber. Seven deep metal mines with high production rates and high heat loads were visited to obtain data necessary to assess their thermal environments. Mine records were examined, wall-roc:, temperatures were measured and a survey of the mine ventilating air and mine drainage was performed. Also, the thermal conductivity of wet and dry specimens of the host rock were measured in the laboratory. Data analysis disclosed that rock heat and adiabatic compression account for stout 60 per cent of the mine heat load at depth. Equipment currently contributes approximately 20 per cent; however, to offset increasing costs with depth, increased mechanization is anticipated. The treat from ground water averages 19 per cent and the contribution from blasting, metabolism and cement is negligible. Also, approximately [0] per cent of the increase in the enthalpy of the ventilation air is in the form of latent heat. Moisture, however, did not significantly affect the thermal conductivity of the rock specimens measured in the laboratory. Also, from the data, it is evident that a negative correlation exists between the thermal conductivity of the host rocks and the per cent of the heat load derived from the wail-rock. Furthemore, steady state heat flow renditions may be assumed in airways where there has been no major changes in the ventilation system for a period of two years or more. Under these conditions, the author found it more convenient and reliable to compute heat influx using the steady state equation for heat flow into a cylinder, rather than Carrier's method for transient heat flow, which is so often used.

Jan 1, 1973

By L. C. IlsLey

The United States Bureau of clines has been conducting Investigations of electrical equipment during a period of more than 25 years in an endeavor to encourage the development of safer electrical equipment for coal mines. In order to conduct these investigations in an orderly manner they are carried out under a published schedule of tests known as Schedule 2C, which specifies detailed requirements for motors, controllers, etc., and fees covering the various inspections and tests made as part of a routine investigation.

Jan 1, 1937

By Serge Rudchenko

A study to determine the potential use of retaining structures in open pit backfilling. Research and review of the open pit mine environment, mine waste disposal, and past and current use of retaining structures. A development of specific structures, the culvert/ tunnel concept, and an anchor block retaining concept. The cost benefit of retaining structures used for in-pit backfilled waste.

Jan 1, 1981

By L. C. IlsLey

The United States Bureau of Mines has been conducting investigations of electrical equipment curing a period of more than 25 years in an endeavor to encourage the development of safer electrical equipment for coal mines. In order to conduct these investigations in an orderly manner they are carried out under a published schedule of tests known as Schedule 20, which specifies detailed requirements for motors, controllers, etc., and fees covering the various inspections and tests made as part of a routine investigation.

Jan 1, 1937

By S. H. Lorain

Tin mining on Seward Peninsula, Alaska, has been intermittently active since the early 1900's. Most of the recorded production (over 2,200 short tons of metallic tin) has been obtained from placer deposits, but recent production also has resulted from development of lode deposits associated with intrusive rocks occurring in the western part of the peninsula. Generally, the lode deposits containing tin minerals (principally cassiterite) are found in dikes, in granite masses, and in silicate zones in limestone overlying the granite. Both the placer and lode deposits have been of considerable strategic interest to the Government because of the almost total absence of a domestic supply of tin. The most important tin-lode deposit discovered to date is in the Cassiterite dike at the Lost River mine, on Cassiterite Creek about 85 miles northwest of Nome. This highly altered, rhyolite porphyry dike averages 12 feet in thickness, strikes N. 75° to 85° E., and dips steeply to the south; it can be traced on the surface for about 8,000 feet. Throughout its explored length of about 2,200 feet the dike everywhere contains some tin and tungsten in veinlets and disseminations; economic concentration of the are minerals, however, is confined to definite shoots. The ore minerals include cassiterite, stannite, hulsite, paigeite, wolframite, scheelite, and base-metal sulfides; gangue minerals include fluorite, boron silicates, and lithium-bearing minerals. Some ore minerals also occur in the numerous other dikes and in the granite and intruded limestone in and adjacent to the mine.

Jan 1, 1958

By R. G. Warncke

In the 1953 National First-Aid and Mine Rescue Contest, 58 teams from 9 States participated, 14 teams from 6 States in mine rescue and 47 teams from 9 States in first aid. Three of the teams were combination teams in that the same team participated in both the mine rescue and first-aid contests. The States represented and the number of teams from each State are shown in table 1. [ ] The contest was conducted in accordance with the general rules prepared by the Rules Committee and approved by the General Committee of the National First-Aid and Mine Rescue Committee.

Jan 1, 1955

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By John R. Duda

The Bureau of Mines is developing estimates of capital investment, operating cost, and selling price for underground mines producing bituminous coal by various mining methods. This study estimates the required capital investment, operating costs, and selling prices for two hypothetical mines designed to produce 1.3 and 2.6 million tons per year (MM tpy)3 by using a longwall system in conjunction with a continuous-mining system. The coal properties being mined are assumed capable of sustaining a 20-year production period. Wages and union welfare payments used in this study are those in effect as of December 6, 1975, as set forth under the National Bituminous Coal Wage Agreement of 1974. Costs of materials and equipment are based on January 1976 indexes. Initial capital investment is $34.6 million for the 1.3-MM-tpy mine and $63.5 million for the 2.6-MM-tpy mine. Capital requirements, including deferred investments, were estimated to be $50.8 and $92.2 million, respectively. These figures translate into total capital investments of $38.51 and $34.91 per ton of annual production. Assuming a desired 15-percent discounted cash flow (DCF) rate of return, with Federal income taxes at 50 percent, the required selling prices would be $13.41 and $12.27 per ton for the 1.3- and 2.6 -MM- tpy mines.

Jan 1, 1976

By G. S. Knoke

This report presents the results of a demonstration of the technical, economic, and environmental feasibility of hydraulic borehole mining of shallow oil sands. Borehole mining offers a method for extracting the oil sands with minimal disturbance to environmental quality because (1) no overburden is removed, (2) no waste rock piles are required, (3) the tailings can be backfilled into the borehole cavity, (4) the ground water quality should be undisturbed, (5) a closed-loop water system can be employed so that no surface streams are polluted, and (6) surface subsidence can be minimized by backfilling the mined cavities. This project consisted of two concurrent tasks: mining operations and environmental monitoring. To generate the environmental impact, nearly 1000 tons of oil sands were mined from two boreholes. Water quality and ground subsidence were monitored. No significant changes occurred in the chemical composition of the process water, indicating that the borehole mining process does not dissolve the mined material. The average subsidence in the immediate vicinity of the boreholes was about 1/2 inch, although some points were noted to be slightly elevated. In general, the amount of subsidence increased with time and decreased with distance from the bore-hole. A mining cost analysis was used to project an estimated cost for production mining of about $38 per barrel of oil.

Jan 1, 1980

By Ira L. Wright

This paper describing the milling practice of the Black Hawk Consolidated Mines Co., is one of a series being prepared by the United States Bureau of Mines. ACKNOWLEDGMENTS Part of the information contained in this paper was furnished by I. H. Stanley, mill superintendent, Black Hawk Consolidated Mines Co., Hanover, M. M., and a part by the South-western Engineering Corporation, Los Angeles, Calif. The assistance of T. G. Chapman in arranging the paper for publication is also acknowledged.

Jan 1, 1930

By J. A. Rowland

Magnesium alloys containing nickel, nickel and manganese, lithium, lithium and manganese, and lithium and aluminum were investigated. Melting, casting, and mechanical working techniques and the heat treatment of various compositions were studied. Amenability to cold and hot working was shown for many compositions. The magnesium-nickel and magnesium-nickel-manganese alloys failed to develop superior mechanical properties and were very low in resistance to corrosion. The magnesium-lithium series, although entirely plastic, had low strength properties. The addition of small amounts of aluminum to the Mg-Li base did not affect greatly either the ductility or the strength; further additions developed increased strength, but only at room temperature, and the alloys became brittle with age. Continued study, concentrating on the ductile lithium-rich beta phase as a base composition for ternary and quaternary systems, is recommended.

Jan 1, 1956

By Donald E. Redmon

This Bureau of Mines report reviews injury experience in the metallic mineral industries for 1966-67. For each of the years, 27 tables summarize disabling work injuries by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973