Search Documents

By Isaac E. "Chip" Harris

Any contractor who agrees to supply materials or to perform services for a sum, is well aware of the importance of proper pre-bid information. Being able to properly plan costs and methods results in profits that allow the contractor to prosper. The paper discusses procedures used in estimating pre-bid cost; in particular, drilling and blasting cost for highways, dams and general construction projects. It breaks cost down into five categories and relates them to a total estimate used in bidding and budgeting a construction project.

Jan 1, 1975

By E E. Cloete, R I. McCrindle

Permitted explosives were previously nitroglycerine based and cap sensitive. Due to safety, health and environmental requirements, water-containing explosives, such as watergels and emulsions, were used instead. However, in order for these explosives to perform at their designed level during blasting, a more powerful stimulus than is delivered by detonators on their own is required.

Jan 1, 1999

By Daniel Castelo, Ben Potter

This paper will discuss the most efficient and effective way to use shape charges when considering standoff distances and the amount of an explosive to be used. For each shape charge test that was performed, a one inch diameter copper liner of 90o was used. Different standoffs for each shape charge were tested to see which one would penetrate the deepest into rolled homogenous armor steel (RHC 44). It was determined that a standoff of three cone diameters provides the deepest penetration. In addition to testing for optimal standoff distances, the effects of overfilling as well as under filling a shape charge with explosive was tested against a shape charge with the bare minimum amount of explosive for correct detonation. These “fill” tests were all performed at a standoff of three cone diameters. Overfilling has little to no effect towards penetrating deeper into a target while under filling a shape charge has an effect of shorter penetration. C-4 explosive was the main explosive for all shape charges.

Jan 1, 2011

By Mick Fritz, Gregory Poole

Construction blasting is always challenging when in close proximity to existing structures, but when you are next to a landmark like Sanford Stadium at the University of Georgia it can get intense. Blasting on this project was performed less than 100 feet from students studying in their dorms at Reed Hall. Some shots are only a few feet from the columns on the stadium that hold up the sky boxes where meetings were being held while blasting was being performed. If a shot goes vertical the rocks would go through the floor of the sky boxes.

Jan 1, 2011

By E Emery Gray, Gary Ard

Each year when hundreds of Engineers and Specialists in the explosives industry meet for the SEE Annual Conference, new ideas are exchanged and new business relationships formed. Harbert Construction Corp. and EGA, Inc., a company specializing in drilling and bIasting, formed such a relationship through mutual interest in such a manner.

Jan 1, 1981

By D. Preece

The mining and oil industry employs techniques such as geologic mapping, core drilling and electromagnetic and potential field techniques to explore for new deposits. Since new discoveries of major near-surface ore bodies are becoming progressively rare and since traditional exploration methods are unable to resolve ore bodies deeper than about 500m, high-resolution seismic reflection techniques show great potential for exploration to much greater depths down to almost 3km.

Jan 1, 2011

By Daniel Richards, Dr Rob Farnfield, Dr Geoff Adderley

The 8-millisecond rule has been in use for many years as a basic technique to help minimize vibration levels from surface blasting operations. The rule was based on work carried out in the 1960’s by the USBM by recording the vibration levels from a series of test blasts in a quarry over a range of distances. This work included the firing of a series of single hole blasts and a number of single row production blasts using a variety of inter-hole delay times. The delay times employed were limited by the technology available at that time to instantaneous, 9, 17 and 34 milliseconds. There have been several papers in recent years suggesting that the use of the 8-millisecond rule is no longer required, when using electronic detonators, due to their enhanced accuracy and greater initiation pattern design flexibility. This paper examines this proposition by revisiting the original work and employing the linear superposition technique to reprocess some of the original recordings. Similar techniques are then applied to a large database of single hole vibration recordings for a range of rock types, distances, and number of decks, with calculated reinforcements compared to the minimum separations in typical patterns. The results suggest that there is some validity to the 8-millisecond rule when applied to electronic detonators but not in the way it is traditionally applied. Simple guidance is suggested for those designing blasts with electronic detonators to minimize vibration levels even if the benefits of linear superposition trials are not available.

Jan 21, 2025

By Lina Lopez, Jose Sanchidrian, Jean Du Mouza, Essaieb Hamdi

This paper evaluates the actual energy delivered by the explosives used in the fragmentation of rock during blasting vs. the available theoretical explosive energy. The evaluation of the fragmentation energy of the blast is first done. Fragmentation by blasting can be seen as a process in which creation of new surfaces within the rock mass is made by generation of new cracks or extension of pre-existing ones. From this idea, the fragmentation blast efficiency can be assessed as the fraction of the available explosive energy used for creation of new surfaces. The evaluation of new cracks area created by the blast is based on the SIMBLOC methodology and the corresponding fragmentation energy is then obtained by the Griffith theory. Secondly, the amount of energy delivered down to a certain pressure or volume along the detonation product expansion process, given by the useful work, is calculated. This is done by first determining the CJ state of the reacted explosive and subsequently performing an adiabatic expansion calculation of the detonation products from that state. W-Detcom code has been used for the calculations using the BKW equation of state with the Sandia parameter set. The fragmentation energy and the useful work are calculated for blasts performed in two mines in Spain. Multiple regression is applied to the results in order to give an assessment of the better description of the explosive energy .

Jan 1, 2002

By Michael A. Barbaglia, Mark William Withey

The lift shot is an essential blast design in the execution of mine creation and expansion plans. Whether it be opening a new quarry, creating a new level in an existing operation, or for control of water, lift shots are utilized to create the desired results. Lift shots by their nature differ from conventional production blasts because they have no free faces for relief of the blast. Due to this fully confined state, the primary direction of the rock movement is vertical, and the potential for excessive vibration and fly rock generation is great.

Jan 1, 1994

By Goran Cirkovic, Zvonimir Ester, Josip Krsnik

During the reconstruction of the motorway Zagreb-Krapina three reinforced concrete bridges were demolished, for their width was not adequate for the new motorway. Demolition of the three bridges was carried out by blasting as duration of the traffic cut on the motorway and the railway was limited to maximally 4 hours. During that period of time the demolished bridges had to be removed. Therefore, very tiny granulation was requested suitable for loading and not endangering the surrounding structures. Before each of three main blasting, trial blasting were carried out including the seismic measurements registering the seismic effects. The nearest residential building was at the distance of less than 30 m from the place of blasting. Additional difficulty was the fact that by each of the three bridges there is a new bridge, with minimal distance between the old and the new bridge being 30 cm. As each of the bridges is of different construction and of various thickness, particular blasting technique has been prepared for each one of the bridges.

Jan 1, 1997

By John Kemeny

There are many methods used to predict blast fragmentation, including empirical and numerical models, field trials, and experience from ongoing blasting. All of these methods require an accurate measurement or prediction of the rock mass properties. These properties include the characteristics of the rock fractures, including fracture density, friction angle, orientation, length, roughness, fill, etc. They also include the hardness of the intact rock, water content, and other parameters. This paper describes three new technologies that can be used to automatically or semi-automatically obtain rock mass properties: digital image processing, 3D laserscanners, and drill monitoring systems. Each of these technologies is described, including the current state of the art, current limitations, and their future potential. Each of these three technologies has advantages and disadvantages. These new technologies, however, have the potential for providing accurate rock mass information in an automated and real time fashion. This information can then form the basis for a new generation of real-time, database driven blast fragmentation models.

Jan 1, 2004

By Ronald Thomas

The scope of this paper is to examine the growth of safety in an individual and offer new goals in that development. The paper will examine the individual's natural growth and show how it parallels the individual in a safety environment. An individual's new goals for safety include more than the standard accident-free conditions. The new goal strives for a safer working environment where unsafe acts are eliminated through independent knowledge and an individual's growth of interdependency in safety related areas of concern. It will explain how this goal cannot be reached unless driven from the top down in an organization but empowered from the bottom up. Various reference or support organizations will be covered. These organizations deal with safety in mining and explosive use of manufacturing. Other support organizations exist but since this paper is "Back to Basics" only a few major groups will be covered.

Jan 1, 2001

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent, high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptablecomputational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By Thomas C. Jones

The purpose of this paper is to disseminate new information for nonelectric blasting in trenching and construction work. The presentation is not designed or intended to discredit conventional electric detonators or use of MS connectors and cord. Its sole purpose is to inform the S.E.E. of new and exciting benefits realized by the use of the Hercudet non-electric system in the construction industry.

Jan 1, 1984

By Paul Worsey, Robert Sickler

Today, America's mining and construction industries are faced with operating under a condition of reduced profit margins. This makes the implementation of new technology far more sensitive to investment return than ever before. For this reason it is imperative that every effort be made to insure that new equipment and processes be designed to maximize their impact on improved quality, reduction in production cost and enhancement of safety. Using these principles as a foundation, a study was made to evaluate potential automation techniques for the blasting industry.

Jan 1, 1987

By Duane A. Houkom

Down time in the Oil Refining and Petro Chemical Industry is extremely expensive. Each day of non-production may easily cost several million dollars. Explosives have been accepted by this industry to solve many of its problems. Explosives offer a solution which is faster, more economical and most important, safer than many of their methods. Our specialties for these industries include: Refractory removal, industrial cleaning, metal cutting and concrete removal. This report does not include information on concrete removal.

Jan 1, 1982

By Joseph Trocino, John Anderson, Stephen Murray

This paper describes the development of LEXFOAM® (Liquid EXplosive FOAM) as a unique low density explosive, and its successful application as an effective tool for "in-place" demolition of landmines and unexploded ordnance. Explosives research using aerosol technology led to the development of LEXFOAM whose components are safely transported and stored as flammable liquids. These components are mixed on site to produce an explosive foam, which enhances safety and minimizes logistical problems. Hand-held, Backpack and Palletized Delivery Systems form a versatile family of dispensing systems to suit any application.

Jan 1, 1998

By James E. Jr Hargroves

With the ever-increasing population growth and modern trend to urban development, the expansion of utilities is a stable, mad or, and constant source of income for many. Blasting is a "necessary evil" to the utility contractor. It can make or break even the most solvent. Housing development expansion and higher treatment of effluents are causing utilities to appear in more congested areas. This paper discusses some of the aspects of utility blasting in the State of Virginia. Consideration is given to bid procedures, pre-blast surveys, record-keeping and practical application.

Jan 1, 1977

Coal strip mine operators in Western Canada often mine steeply-dipping multiple coal seams in mountainous terrain. The ability to fragment the rock waste layers above and below these seams with minimum disruption of the seams in large blasts normally involves decked charges in large rotary boreholes. Mining these seams may take two or more separate blasts to break the waste wedges above and below the coal, but these wedges can be blasted in a single shot for better mining efficiency.

Jan 1, 1985

By S. Klerkx, R Battulwar, J Valencia, J Sattarvand, E Emami, M. Soleymani Shishvan

A new technology for energy distribution optimization, supported by NIOSH.

Feb 1, 2020