Search Documents

By Héctor X. Toro, José Francisco Cabello, Douglas Batista, Álvaro Videla, Claudio Luiz Schneider

The Minas-Rio Project, located in the state of Minas Gerais, Brazil, is currently under construction. The new plant will have a regrinding circuit that uses VertimillTM. The objective is to process itabirite iron ores and it is expected that the consumption of media will represent a large part of the plant operating cost. Many studies in the literature indicate that the size of the grinding media directly influences the grinding efficiency. The size distribution of the charge media is related to the surface area of the charge. In this study, a sample of itabirite iron ore was tested with respect to grindability in a laboratory scale ball mill. The test mill was equipped with a torque device to accurately measure power consumption, as required for the determination of energy specific kinetic parameters. Five tests were carried out with different sizes of steel balls and with SICAM (sub-inch Cast Media). The size distributions of the feed and product of the several grinding tests were used to calibrate population balance model parameters for each condition. The results confirmed that the ball charge with smaller diameter is the most efficient among the different media charge tested.

Jan 1, 2014

By C. R. Mambote

One of the processes developed for vanadium recovery from the fly ash of crude oil is through acid leaching. In the process, iron is one of the impurities that should be removed before vanadium precipitation, due to the fact that iron tends to co-precipitate with vanadium. The mechanism of iron precipitation is understood in terms of ferric hydrolysis, followed by the dimerization and subsequent polymerization of the crystalline iron compound. In order to develop a new approach for the fly ash processing, in the present paper the precipitation of iron from the liquor after the leaching process was studied with addition of NaOH or NH4OH in the presence of H2O2 or Na2C2O4 at 80°C. The objective was to investigate the feasibility of the selective precipitation which could be applied to vanadium and nickel recovery from the fly ash. The experimental results show the difficulties of removing iron by precipitation without co-precipitating nickel and vanadium.

Jan 1, 2014

By F. Bello, J. Engels

"During 2012 and 2013, Minera Esperanza conducted a series of thickening and deposition trials to identify design and operational parameters associated with increased thickening of its tailings. These trials focused on benchmarking the current solids concentration of tailings (62 - 64%) in anticipation of an increase to 67% solids once two new 45 m diameter deep-cone paste thickeners are commissioned in 2014. These trials studied the sedimentation and rheological characteristics of the existing tailings and performed deposition modelling to assist with developing short- and long-term designs for the tailings storage facility. To verify and optimise these models, Minera Esperanza considered a series of laboratory, pilot, and industrial-scale deposition trials. This paper provides a review of the trials conducted in the laboratory and at industrial-scale and considers the results and optimisations for the short- and long-term design of Minera Esperanza’s tailings storage facility."

Jan 1, 2014

By G. Alfano

We have investigated the breakage actions of solid particles observed in a new generation fluid energy micronizer being set up at our laboratories. The attention has been focussed in particular on breakage caused by interparticle collision, particle impact against a fixed surface, interparticle attrition and particle against wall of jet mill attrition. We have also studied the influence of grain size distribution, maximum particle size, flow rate and characteristics of the solid to be processed, as well as of flow rate and pressure of injected air on the above mechanism. Lastly, the operating parameters of a dynamic air classifier in closed circuit with the micronizer for recovering the fine fraction and automatically recycling the oversize, have been optimized. The findings of this investigation have been used to design, build and fine tune a micronizer capable of controlling the top size of a product having average particle size that meets market requirements for fine powders, while keeping power consumption relatively low.

Jan 1, 2014

By T. N. Matveeva, T. A. Ivanova

"The article presents the results of the research aimed at development and testing of new effective reagents – collectors and green modifiers for more complete extraction of gold and platinum to concentrates at reduced loss with waste products. The main deposits of Au and PGM ores of Russia and abroad are presented by refractory raw material with the non-uniform finely-interspersed sulfide mineralization, submicron gold and platinum, the low metal content, non-uniform distribution of valuable minerals. and show low indicators of recovery. The main losses of precious metals (up to 15 %) at flotation are associated with thin slam tailings because of inefficiency of standard reagent modes.In the paper, the new trends in design of collecting agents for extraction of gold and PGM sulfide minerals and their application in flotation tests are substantiated. The original technique for obtaining the modified collector reagents – dithiocarbamate, dithiophoshpinate and dithiazine, incorporated non-ionic compounds that are able to generate stable complexes with gold and platinum has been developed. A novel class of collectors – cloud point polymers showed high flotation recovery of fine particles of gold and platinum. The original technique to create the mineral samples of natural sulfides with ""invisible"" or sub-micron gold on their surface designed helped to indicate the mechanism of selective adsorption of novel agents on Au and Pt-sulfide minerals. Extractive UV spectrophotometry, potential measurements, X-ray phase and spectral analysis, scanning electronic microscopy (SEAM), laser SIM and AFM microscopy were applied to analyze the adsorbed layer of modified reagents on the mineral surface. Selective hydrophobic covering on the surface of micro- and nanoparticles of noble metals provided an increase in their extraction during flotation. New reagent modes of modified collectors and green modifiers were tested in scaled-up laboratory flotation and the results obtained demonstrated the increased quality of the concentrates in terms of gold content by 1.5 times and higher gold recovery by 1.5-5%. The studies have been supported by Grants of the President of RF “Scientific School of Academician Chanturiya” NSh-220.2012.5; NSh-748.2014.5."

Jan 1, 2018

By M. Abdollahy

Solvent extraction of gallium from Bayer solution of Jajarm Alumina plant was investigated us-ing Kelex100 as extractant. Taguchi experimental design method was used in order to optimize the separation factor of Ga and Al. Optimum conditions were obtained as follows: Temperatuer: 65°C, volume ratio of aqueous phase to organic phase: 3.0:1.0, process time: 60min and organic phase containing 15vol.% Kelex100, 5vol.% isodecanol in kerosene. In this conditions, 74% gallium and 0.3% aluminum was extracted and separation factor was obtained 828.63.

Jan 1, 2014

By Maurício Torem, Gabriela Huaman, Antonio Merma

The purpose of this review paper is to succinctly present the most significant works related to Mineral Processing and Environmental Bioremediation and developed by the Mineral and Environmental Technology Group (METG) of the Materials Engineering Department of the Pontifical Catholic University of Rio de Janeiro (PUC-Rio). In mineral processing it was emphasized the use of the Rhodococcus opacus bacteria as a bioreagent in the bioflotation of some mineral samples (magnesite, calcite, hematite, quartz and apatite). The adsorption of the bacterial cells on the mineral surface can be due to specific and/or non-specific interactions, which will depend on several factors, as their surface charge and hydrophobic character. The zeta potential evaluation of the mineral particles before and after interaction with the R. opacus cells showed that the biomass modified the zeta potential profiles of the minerals, which confirm the adsorption of bacterial cells on the mineral surface. Moreover, the bacterial cells adsorbed caused a change in the mineral flotability which is related to a change in their hydrophobic character, thus, the mineral bioflotability was found to be dependent on the pH and the bacterial concentration. On the other hand, the environmental bioremetiation assessed the biosorption potential of three metal ions (lead, copper, and cobalt) by four different biomass Streptomyces lunalinharesii, Rhodococcus opacus, Rhodococcus ruber and coconut shell powder. For this purpose, biosorption process was characterized under different operating conditions such as initial pH and biosorbent dosage. The Freundlich and Langmuir isotherm models were applied to the equilibrium data obtained at different concentration.

Jan 1, 2014

By G. Venkateswara Rao

The jigging of ferrous ore to produce higher-grade products has been practiced for many decades. This is due to easy separation, a beneficial trade- off between operating cost and reduced yield relative to Dense Media Separation (DMS). Jigging becomes prominent for beneficiation of iron ores in the coarser size range. At present drive is towards the use of under bed air pulsed jigs for the beneficiation of ferrous ores. The main advantage is that the under bed air pulsed jigs are capable of generating the large pulse of amplitudes required to fluidize a deep bed of heavy ores particularly lump iron ore up to 40mm size. The major jig parameters effecting the jigging operation are bed height, shape of the pulse, residence time, operating pressure, valve cycle time and water flow rate. With the pulse shape set correctly for optimum stratification rate, even it is still necessary to provide enough residence time, to ensure the difficult material will take time to migrate to the expected layer in the bed. In order to find the Jig Stratification Index (JIS) parameters like bed height, operating pressure, water flow rate, cycle valve time and shape of the pulse were optimized first by conducting various tests. Typical Iron ore samples from Odisha (both lump and fines) were subjected to stratification studies at residence time of 1, 5 and 15 minutes. Jig Stratification Index (JSI) for both lump (0.30) and fines (0.20) were determined by using APIC Jig. The maximum possible JSI was calculated by using heavy liquid separation test (0.42 for lump and 0.24 for fines). It is found that the jig bed JSI is less than the Heavy liquid JSI for both lump and fines. The ratio of Jig bed JSI to the heavy liquid JSI is 0.83 for lump and 0.71 for fines. The JSI and ratio of Jig bed JSI to Heavy liquid JSI are low for fines due to fluid turbulences causing some degree of remixing in the jig bed. The fluid turbulences are more for fines than lump, hence jigging of fines is difficult and challenging. Keywords: sub grade iron ore, gravity separation, jigging, apic jig, stratification, residence time, jig stratification index

Sep 1, 2012

By Brabcova Z.

This contribution deals with bubble adhesion on particle surface which consists of three steps ? the liquid film thinning, the film rupture and expansion of the three phase contact (TPC). Our attention is devoted to the third step ? to the description of the TPC expansion. Three-phase contact line expansion can be theoretically described using hydrodynamic and molecular-kinetic models. Both of these models were originally developed for the interaction of the bubble with horizontal plane in pure water. Our experiments deal mainly with the interaction of the bubble with the inclined plane in the solution of surface active agents. It was proved experimentally that molecular-kinetic model corresponds also to these conditions and this model was used for the description of the TPC expansion. The model is based on the theoretical description of the bubble contact angle on the three-phase interface. These contact angles change dramatically from 180o to equilibium (Young) contact angle close to 90o. Modificated ADSA method is used for the calculation of the contact angle. This method utilizes the Laplace equation of the capillarity; the bubble profile and the contact angle are evaluated using the set of experimental points around the edge of the bubble. The comparison of the experimental and calculated bubble profile shows a good agreement. The aim of the project is to describe the process of the TPC expansion during the adhesion of the bubble with the diameter up to 1 mm. Inclined planes were used instead of an experimental solid particle. Our experiments were provided in the solution of surface active compounds. The process of the adhesion was recorded using high-speed digital camera and images were evaluated using the image analysis software NIS-Elements. Calculations were performed using the MATLAB software. Keywords: bubble-particle interaction, adhesion, three-phase contact, contact angle

Sep 1, 2012

By Weiran Zuo, Narayan Krishnan, Frédéric von der Weid, Emmy Manlapig, Fengnian Shi, Klaas van der Wielen

Laboratory study has identified a new application of high voltage electrical pulse technology for pre-weakening ores. In recent years, the Julius Kruttschnitt Mineral Research Centre (JKMRC), Newcrest Mining and SELFRAG AG have conducted joint research in validation of pre-weakening of SAG mill feed through the pilot scale tests and comminution circuit simulations. Ten tons of SAG mill feed with a top particle size 150 mm were tested with two pilot scale SELFRAG machines installed in Switzerland. A simulation study using JKSimMet software was carried out to find where the high voltage pulses pre-weakening technique can be best applied in a gold-copper ore comminution circuit, based on the data of the pilot scale SELFRAG tests. A novel comminution circuit was designed, which incorporated SELFRAG to pre-condition part of SAG mill feed (9.5 to 150 mm) and to treat the circulating SAG mill pebbles. The high voltage pulse technology effectively reduced the amount of ‘critical size’ particles in the SAG mill and pre-weakened particle strength for grinding. Attributing to the nature of bi-modal size distribution and the significantly reduced F80, the simulations showed that the SAG mill had spare capacity to process part of hydrocyclone underflow from the secondary ball mill grinding circuit. The simulations indicated that the novel comminution circuit had the potential to remove two MP1000 pebble crushers and one 10 MW ball mill from the existing 2000 t/h grinding circuit. A 5 kWh/t energy reduction by adopting the novel comminution circuit in a gold-copper operation may be realized. This would result in substantial savings in operation costs.

Jan 1, 2014

By V. V. Morozov, I. S. Barmin, A. V. Tugolukov, V. V. Polivanskaya

"It was presents the results of research on improving reagent regime and scheme of enrichment of slime classes of Apatite-Staffelite ores and tailings stockpile of Kovdorsky enrichment plant. It was investigated the regularities of flocculation in the processes of thickening and selective flotation apatite-bearing ores. It was established character of the influence of flotation reagents on the flocculation process. It was shown that the sodium silicate and soda ash have a stabilizing effect by thickening of sludges. Neonol and oleic acid have a coagulating or flocculating effect. It was tested the new regime flotation, involving an initial conditioning with using of reagent - dispersants before feeding the pulp into the flotation and subsequent conditioning with reagents having a coagulating effect. The flowsheet and reagent regime for enrichment of fine-grained tailings stockpiled was developed, which providing production of standard apatite concentrate and increasing the recovery of valuable components. There are presented results of the research of activities of strong organic surfactant on solubility of colloidal form fatty acid collector and aggregate stability of fine minerals in the process of thickening and flotation. Surfactants such as Neonol have been investigated for increasing the activity of the collectors. When using the process of thickening sludge fraction with flocculant Praestol 2540 and stadial conditioning of sludge were obtained concentrates containing up to 38.1% P2O5 at recovery. INTRODUCTION A feature of the Apatite-Staffelite ores of the Kovdorsky deposit is the presence of a large number of fine mineral particles and a reduced hardness of phosphate minerals (Beloborodov et al., 2010, Tugolukov et al., 2012). Formed in the ore-preparation process, sludges are lost with a discharge in the thickening operation. Sludge is characterized by an increased content of phosphorus pentoxide (P2O5). Losses of P2O5 at enrichment of the stale tailings of Kovdorsky GOK reach 14.0%. The high losses of P2O5 caused a profound study of the behavior of thin apatite classes under conditions of thickening and flotation."

Jan 1, 2018

By S. Vimalnath

The bioremediation capability of Pseudomonas aeruginosa cells was investigated for the biosorption of lead ions from aqueous solution. The various parameters such as pH, kinetics, biomass loading and concentration of lead affecting the biosorption process were studied. Complete bio removal of lead could be achieved for an initial concentration of 12.4 mg/L at pH 6.2, corresponding to typical industrial effluents. The biosorption isotherm followed Langmuirian behavior and the Gibbs free energy (?G) was determined to be-30.8 kJ/mole, indicative of chemisorption between the functional groups of the bacterial surface and lead. The biosorption kinetics adhered to a pseudo-second order model. The possible mechanisms of interaction of lead with the bacterial cells are discussed. A carbon paste electrode with a coating of biomass was developed for lead ion detection in aqueous solution using cyclic voltammetric technique. Concentrations of lead up to 5x10-5 M could be successfully detected using cyclic voltammetry, which could be improved to a detection limit of 1x10-8 M adopting differential pulse anodic stripping voltammetry (DPASV). Keywords: Pseudomonas aeruginosa, bioremediation, lead, voltammetry

Sep 1, 2012

By A. Oberrauner

Electrostatic separation is a dry separation technique usable for many applications in the mining- and recycling industries. At the Chair of Mineral Processing intensified research has been done on this topic during the last years. One challenge was to measure the triboelectric charging of fine mineral particles in a triboelectric charging device consisting of an electrically insulated polyethylene rotor/stator assembly. These tests, performed on monomineralic samples, were accomplished in a climate chamber. It was shown that charging of minerals not only depends on rotor speed, feed rate and atmospheric circumstances but also on the properties of the applied electrostatic field. Tests on pure calcite in contact with the polyethylene rotor/stator system resulted in specific triboelectric charges up to +10 nC/g at low relative humidity. With more water present in the surrounding atmosphere, these charging values decreased significantly. However, at higher relative humidity, triboelectric charge values could be maintained after an electrostatic field of positive polarity was applied. Similarly, charging behavior was found with other hydrophilic minerals. The idea behind all these tests was to find the largest charging difference between minerals occurring together in a deposit and to be able to charge them oppositely, assuming that this means good sort ability in an electrostatic separator. The results gained from these investigations are shown. After having obtained many results on charging pure minerals, it became interesting to test the applicability of the charging tendencies on electrostatic separation of fines <100 µm. In order to do so, a separator for fine polymineralic powders was developed, constructed and combined with the triboelectric charging device, all being set up in a climate chamber. This new so-called coax-separator is presented along with first test-results.

Sep 1, 2012

By Zoran S. Markovic

The extensive laboratory investigations were carried out in order to determinate behavior of sulphide and nonsulphide copper bearing particles during the flotation. The present ore sample were contained 0.55% Cu with 20.1% of nonsulphide copper in it and gangue material with higher contents of alumina about 19.07%. In this paper will be presented some results such as: effect of particle size, pH and applied collectors. The main goal was in application of collectors S-7518, as well as mixture of KEX and Z-96. Z-96 is a product from Chemical Industry Zupa Krusevac which was used as auxiliary collector in mixture with xanthates. The best results were done with this mixture in ratio KEX / Z-96 as 77/23 % in area of oxidized minerals flotation, but the collector S-7518 was achieved better results in sulphide mineral flotation. The S-7518 has better selectivity between copper minerals and pyrite comparing to mixture of KEX/Z-96 in mentioned optimal ratio. Flotation recovery and copper grade in concentrate were studied by flotation kinetics tests.

Sep 1, 2012

By V. Tsyplakov

This article reviews factors of preg-robbing effect, occurring in the course of pressure oxidation of ore and concentrates, containing chloride compounds and so-called &apos;organic carbon&apos;. The article also summarizes the main results of the studies and testwork conducted to overcome this effect. The following efficient preg-robbing mitigation methods have been noted: higher temperature of pressure oxidation process, preliminary removal of natural carbonaceous material from concentrate, chloride removal prior to concentrate pressure oxidation, and addition of water-soluble organic blanking agents, which suppress the adsorption activity of the native ore adsorbents. Keywords: preg-robbing, double-refractory gold concentrates, pyrite, arsenopyrite, blanking agents, pressure oxidation, autoclave leaching

Sep 1, 2012

By A. Boehm

Mineral selective flash roasting (Steiner process) in oxidizing atmosphere was tested successfully for the efficient low intensity magnetic separation of siderite from ankerite and other gangue minerals within the ore of the Steirische Erzberg, Austria. The calcium, magnesium and manganese containing siderite turns selectively into a ferromagnetic oxide phase while ankerite remains paramagnetic. The expulsion of CO2 increases the volume specific surface depending on the selected temperature. Unlike pure iron oxides absorbing SO2 below 530°C, the calcined siderite (enriched in the magnetic product of the Steiner process) acts as a sorbent for SO2 between 500 and 820°C. The effect was studied by thermogravimetric analysis and particle bed tests complemented with neutron thermo diffractometry (D20/ ILL). The energy input was simulated with the help of a tube furnace. The composition of the artificial combustion gas permeating the bed was close to that measured in pilot scale tests (6 % CO2, 12 % O2, 700 vpm SO2). The evaluation of data relating the SO2 variation in the off gas monitored by electrochemical cells to the actual phase composition revealed an intermediate ferrite phase as absorber. During the rapid decomposition in oxidizing atmosphere starting at 500°C the occurring siderite alters to a (CaO, MgO, MnO)Fe2O3 ferrite as an intermediate phase accompanied with sudden SO2 absorption. SO2 disintegrates the ferrite structure forming MgSO4 and MnSO4, taking Fe2O3 as a catalyst. Ankerite (enriched in the non magnetics of the Steiner process) starts to absorb at temperatures above 1000°C forming gypsum. The findings support the SO2 controlled operation of the Steiner process by ?autodesulfurisation?. It explains aspects of the SO2 implementation reactions within off gas recycling in Austrian sinterstrands. Keywords: magnetising flash roasting, neutron thermo diffractometry, SO2 absorption, siderite, ankerite

Sep 1, 2012

By B. Friedrich, A. Weyhe, H. Heegn

"Nickel-metal hydride batteries (Ni-MH) are storers of electrochemical energy, which have a higher specific storage capacity than lead or nickel-cadmium batteries. The demand for Nickel-metal hydride batteries is increasing rapidly since their market launch in the early 1990’s. Today there is no suitable and sustainable recycling process to recover nickel, cobalt and rare-earth metals. The discarded batteries are used today in the steel industry as alloy material because they contain nickel. Cobalt and rare-earth metals (RE) are lost; they are non-recycleable.In a German governmental funded research project, IME Aachen, ACCUREC Mühlheim and UVR-FIA Freiberg are cooperating in processing as well as in creating a feasibility study. The target of this project is the development of a new recycling process for metal recovery from Ni-MH-batteries. The proposed process described in this paper consists of a combination of mechanical, pyrometallurgical and hydrometallurgical processing steps. This process is capable of treating all types of Ni-MH-batteries. After comminution steel and organics are separated. The separated Ni-MH is smelted in an electric arc furnace. The products are a nickel-cobalt alloy and a slag phase enriched with rare-earth oxides for further treatment to ‘mischmetal’. Both the Nickel-Cobalt alloy and the ‘mischmetal’ will be directly used in battery production."

Jan 1, 2003

By V. A. Zhilina, I. V. Shadrunova, O. E. Gorlova

"The aim of the study is to develop and scientifically justify a new adaptive approach to the separating processes of deep and complex processing technogenic mineral raw materials. Technogenic mineral resources as a waste of mining and processing industry are mostly complex objects that have specific features of material composition and technological properties and make it processing ineffective with traditional schemes of mineral raw materials enrichment. Mineral wastes are regarded in this study as a complex object with a large number of signs in conditions of uncertain environment and object. However, adaptation is regarded as the process management system’ adaptation to the specific the properties of the object and the environment that has several hierarchical levels corresponding to different stages in the management of complex object. An adaptive approach is considered as a methodological basis of multivariate schemes for opening the mineral resources and creating mechanisms that could transfer these potential technogenic resources to the actual that significantly expand the mineral resource base of the country's black, coloured, rare, noble metals and construction materials. In this case, potentially the solution to the most pressing social and environmental problems associated with the adverse effects of past economic activity simultaneously with the commercial objectives. This approach to the wastes mining and related processing manufacturers meets the core idea of sustainable development as the balance of interests of State, society, business, private enterprise and each person in the areas of rational use of resources, economic efficiency and environmental safety. On the example of metal-containing raw materials in the form of slags of ferrous and nonferrous metallurgy, ferrous metallurgy sludge, mature fine tailings, the application of adaptive approach illustrates to the development of technologies of its deep and complex processing as phased, thoughtful movement from a comprehensive study of technogenic raw materials to build optimal topologies of technological schemes for processing the mineral wastes. INTRODUCTION Involving the Russian economy in the system of global economic relations significantly changes the nature of the country's competitiveness in the development of the world market and urgently requires competent management of its own natural and mineral resources. The latter at the present time in real economic processes cease to be a passive material foundation and become the producing basis in the production processes in the status of so-called natural capital. Introduced in the field of economic theory at the end of the 20th century, this term means both the flow of natural services and real natural resources. Consequently, natural objects, which act as natural resources of a certain production, today must necessarily be evaluated in a strategic sense. Modern standards of sustainable development presuppose that the economy should equally be oriented to balance the interests of the state, society, business, individual enterprise and each person in the spheres of rational use of resources, preservation of healthy ecosystems, ensuring well-being, high quality of life and environmental safety of not only the current generation, but also respect for the rights of future generations, that is, intergenerational equality. Most types of minerals are classified as non-renewable resources, therefore resource-saving in the sphere of mineral and raw materials complexes is one of the most important factors-indicators characterizing the degree of approximation to the model of rational subsoil use, and, consequently, sustainable development (State Report, 2017)."

Jan 1, 2018

By Güven Önal, Gülay Bulut, Mustafa Özer, Yunus Emre Benkli, Olgaç Kangal, Mustafa Tarkan

There are various types of natural zeolite deposits in Turkey. Naturally occurring zeolites are excluded from many important commercial applications where uniformity and purity are essential. In this paper, the beneficiation of natural zeolite, taken from western part of Turkey, was investigated. According to X-Ray Diffraction (XRD) and mineralogical studies carried out on the representative ore sample, the natural zeolite was found to be in the forms of clinoptilolite and heulandite. Clinoptilolite forms as a devitrification product of volcanic glass in tuffs. Quartz, clay minerals, orthoclase, plagioclase, biotite, seruzite-muskovite and epidote were observed as impurities. Several types of mineral processing methods were performed in order to remove impurities from the natural zeolite sample to produce high purity zeolite. Gravity separation methods such as shaking table and superpanner were carried out for separating heavy minerals, while high intensity dry magnetic separation was used for discarding magnetic minerals.

Jan 1, 2003

By Rainer M. Lotzien, Michael J. G. Battersby, Jan Kleefeld, Julian V. Brown, Rainer M. Imhof

"The standard method of separation using flotation is compromised in terms of kinetics and efficiency, because of the generally slow separating differentials of fine bubbles and fine particle suspensions. A new flotation system has been developed that addresses these issues and imparts other benefits. The new technology is based on established pneumatic flotation designs called Imhoflot which use intensive in-line pre-aeration to aerate the flotation pulp prior to its introduction to the separating cell. Consequently the cell is designed only for the separation of the phases and not for bubble-particle contact. In the new system this separation is speeded up dramatically by the introduction of centrifugal motivation in the separating vessel, without the use of internal moving parts. The design focuses on providing increased differential forces on buoyant mineralised bubbles and hydrophilic fines. The observed result of these differential forces is the improvement of concentrate qualities by the reduction of the amount of misplaced material found in the froth. The commercial benefit to industry is much reduced residence time, less than 30 seconds, which offers considerable cost savings in equipment and infrastructure.Prototypes of 0.65m, 1.7m and 2.2m cell diameter size have been constructed for hydrodynamic and industrial scale tests to assess the previously established computational methods for scale up of the process. The 1.7m cell has been installed and operated for cleaning of potash concentrates in Germany, at throughputs of 150 m3/hr, with extremely encouraging results. A 2.2m cell has been installed and operated in plant trials for superfine coal in South Africa. Results are presented that illustrate the effects of differential separations by comparison with conventional pneumatic and mechanical flotation techniques. Predictions of performance are provided in the contexts of the applications tested."

Jan 1, 2003