Search Documents

By M. Pischtschan, S. Belz, M. Perrucci

In High Pressure Grinding Rolls (HPGR), the material grinding takes place between the fixed and floating rollers. In this regard, the rollers start to wear over a period of time, which is impacted by for e.g.: ore characteristics, operating pressure, feed material size and non-uniform feed presentation across the roller width. HPGR operational experiences have shown that the rollers do not wear at the same rate. This differential wear rate over time leads to differences in the tangential speeds of the rollers, causing an uneven gap between the fixed and floating rollers in relation to the material. This unwanted but extremely common situation results in a less effective grinding process due to the fact that the slip between rollers is not optimal. As the rollers wear profile increases, the roller with smaller diameter starts to wear further, deteriorating the comminution efficiency up to a point where operators have to stop the HPGR to replace the rollers. Since the wear rate of the rollers is not equal, the replacement of the same cannot be properly planned so that their life-time are fully utilized. In this paper, a dynamic load share control with the use of ABB’s variable speed drive system is proposed, which provides the possibility to the HPGR operator to impact the roller wear in such a way that it equalizes the wear rate to a certain extent and extends the roller life time. Called RollXtend™, this solution includes a load share factor which can be parameterized based on the wear measurement performed manually during maintenance procedure. Additionally, this paper describes an automated load sharing concept based on a non-invasive wear measurement method. The partial results of the technology trial in a copper/gold mine are presented, which aimed at detecting stud damage and estimating the real rollers profile throughout their life time. The final objective of the pilot project was reduce the amount of planned and unplanned downtimes of the HPGR by increasing the rollers life time and avoiding catastrophic stud damages.

Jan 1, 2018

By J. Broadhurst

"A number of metal supplying industries have in recent years seen the compilation of life cycle inventories (LCIs) and life cycle assessments (LCAs). The activity has largely been driven by the interest of ultimate metal users, such as the automotive industry, in the interest of designing more sustainable products. Often, the compilation of such inventories has been little more than an auditing exercise. However, the process of conducting an LCA can have more value, guiding designers and operators to points within the technology train where significant emissions and impacts originate. The LCA product can thus be used to inform on-site environmental management, and, where process data is used to construct dynamic operational models, to support strategic decision making in the realm of project planning and technology selection. LCA thus serves as a valuable tool to support the industry’s drive to support the sustainable development of the societies in which it operates.This paper reviews and compares the priorities of environmental and closure planning in the design phase, with environmental management and auditing during operation, and with green procurement of minerals and metals products. It shows how life cycle assessments of various complexities can be used to reconcile these various objectives, ensuring that the latter, critical to business success, can be addressed from the outset in a new project. The paper then reviews a case study of the use of LCA in the base & precious metals industry, where the complexity of the operation disallowed the simpler auditing process so that a detailed process understanding had to be built up in order to compile a meaningful life cycle inventory."

Jan 1, 2003

By Alejandro Rubio-Lopetegui, Gonzalo Montes-Atenas

The occurrence of Enargite (Cu3AsS4) in hydrometallurgical plants bears a number of challenges. One question lies on how Copper and Arsenic can be selectively extracted from the solid surface structure when immersed in aqueous solution. The leaching of Enargite in ambient conditions has been extensively studied; nevertheless, challenges regarding the process kinetics and surface structures enabling the extraction process remain ill-understood. Prior knowledge indicates that different conditions of pH, Eh, temperature, speciation of the aqueous phase or variations of these parameters defines the overall rate at which metals and other elements will be transferred to the solution. One aspect that the research studies have seldom addressed involves studying the main features of the surface structures formed during the leaching process at the outmost surface atomic layer. Such structures will mediate between the solid bulk and the solution to undertake subsequent stages of leaching process. The aim of this research work is to critically analyze the state of the art of Enargite electrochemistry from the mediator formation-dissolution mechanisms standpoint occurring at the mineral-solution interface. The most probable mediator species reported in the literature were found to be: Arsenolite and Sulfur (acidic media), Covellite (acidic and alkaline media) and Tenorite (alkaline media). As a result of this analysis, it was observed that the surface speciation was not in full agreement with the previous knowledge suggested to explain Enargite leaching reactions and, therefore, modified Eh-pH diagrams are presented. The acquired insights on the surface structures rising from the Enargite-aqueous solution interactions is further revised to provide new experimental protocols towards selectively separating Copper and Arsenic through hydrometallurgical paths.

Jan 1, 2014

By G. P. Wong

"The Inco Matte Separation process was the first commercial application using mineral processing techniques to separate nickel from copper from a slow-cooled matte in Sudbury since 1945. In Inco Sudbury operations, bulk sulphide concentrate containing chalcopyrite, pentlandite, pyrrhotite and some gangue minerals is flash smelted and converted to Bessemer matte. During the controlled slow-cooling of the Bessemer matte, discrete mineral grains of new mineral phases are formed: copper sulfide precipitates as chalcocite (Cu2S), nickel sulfide as heazlewoodite (Ni3S2) and a Cu-Ni-Fe alloy is also formed. Flotation is employed to separate Cc from Hz under high lime conditions (pH>12) with diphenyl guanidine (DPG) as both collector and frother.A simplified matte separation flowsheet is as follows. After grinding, the Cu-Ni-Fe alloy is removed by magnetic separation. All precious metals are recovered in the metallic alloy. Following the rougher flotation, a Cu concentrate is produced after cleaner and re-cleaner flotation in mechanical and column cells. Two Ni concentrates are produced: a high-grade Ni product containing less than 0.8% Cu from the scavenger column tails and a low-grade Ni product containing 5% Cu from the middlings circuit tails. A stream containing the inseparable Cc and Hz from the middlings circuit is generated and recycled back to the smelter. The quantity of this stream is typically about 3% of total feed and can be as high as 5%, greatly decreasing the overall matte separation efficiency. The large mass of the recycle stream is a direct result of poor Cc/Hz separation selectivity in the middlings circuit. The middlings circuit, consisting of a thickener, a regrind mill and two columns, processes two streams: cleaner tailings and scavenger concentrates. The thickener contributes significantly to oxidation due to the long residence time of the pulp in this unit."

Jan 1, 2003

By S. Mohanta

The air dense medium fluidized bed separator which has been developed for the dry beneficiation of coal is recognized as a low cost and high efficiency process. The success of this separator for beneficiating any specific coal, alone or in combination with other processing methods, mostly depends on the characteristics of run-of-mine coal. Therefore, a thorough knowledge of the mineralogical composition and washability characteristics of representative coal sample is highly essential for correctly and effectively assess the suitability of this process. Available literature conforms that although the characteristics of Indian non-coking coals are well known, the correlations between the particle compositions with its density are entirely lacking. In the present study the washability, proximate, ultimate and elemental analysis was conducted for four typical Indian high-ash non-coking coals and their elemental compositions were well correlated with the specific gravity of coal. The results obtained in this study provide some essential information to the coal-processing engineer for efficiently operate and control the process. Furthermore, the beneficiation potential of air dense medium fluidized bed was experimentally evaluated and compared with the results obtained from an operating wet beneficiation plant. Based on this comparative study the air dense medium fluidized bed is established to be a possible alternative to the conventional wet beneficiation method for beneficiating Indian coals with Ep values in the range of 0.03 to 0.06

Sep 1, 2012

By I. V. Makarskii, D. N. Nikitin, L. G. Tarasova

"The extent and nature of the damage to diamonds at processing plant is largely determined by the design features of the equipment, the characteristics of the feed ore and the parameters of the ore disintegration process (change in the rotational speed of the autogenous mills, variations of the water supply to comminution process, choice of the optimum charge, etc.). To monitor the intactness of diamonds, an instrumental method using the X-ray tomography system and colored synthetic indicator diamonds was developed for identifying the process-related damage. The X-ray tomography system consists of a CT-Portable X-ray tomographic scanner, a crystal positioning device and customized software (developed by the Fraunhofer Institute and Aliud GmbH, Germany). The developed method enables improvement of the accuracy of the results, exclusion of the subjectivity of the mineralogical assessment, acceleration of data processing and promptly planning of the activities aimed at reducing the process-related damage to diamonds. KEYWORDS Diamonds, colored indicator diamonds, process-related damage, loss of mass, instrumental method, X-ray tomography system. INTRODUCTION Industrial tests of ore processing technology at the enterprises of ALROSA PJSC are accompanied by assessment of the process-related damage to diamonds. The assessment of the process-related damage to crystals is carried out for prompt elimination of factors contributing to the increase of impact forces in the process flow sheet of ore treatment plant. For this purpose a specially selected parcel of -4.0 + 2.0 mm sized natural indicator diamonds is used. The diamonds are exposed to ionizing radiation in order to turn them green and thus to create a distinctive feature. Colored natural indicator diamonds are described, photographed in several views and introduced into the process flow sheet of the processing plant, then extracted from the process flow, described and photographed again. The comparison of diamonds before and after their passing through the process flow sheet of the plant allows to find evidence of process-related impact on the crystal and to calculate the factor of process-related damage (the number of crystals damaged during liberation and recovery), the loss of crystal weight and the degree of damage to the crystals. The method of colored indicator diamonds is used to select processing methods, equipment or regime which would be the safest for diamonds based on the analysis of the factors of process-related damage. There are limitations of the method, such as:"

Jan 1, 2018

By I. A. Makalin, V. N. Yakovlev, S. V. Imangulov, I. V. Zyryanov

"The presented studies aimed at solving the problem of recovery of low-luminescent diamonds, which are not recovered using X-ray luminescence method of processing of diamond-bearing ore. The purpose of the studies is the determination of possibility and feasibility of recovery of such crystals using dual-energy X-ray transmission separation technology. In preparation for studies methods were developed for testing technical and process parameters of XRT-400 Aliud GmbH (Germany) sorter, manufactured according to design specifications of Yakutniproalmaz Institute, and XRT/D TOMRA Sorting Solutions GmbH (Germany) sorter, designed for processing of -50+5 mm ore, as well as RGS-1M, RGS-2 X-ray sorters, developed by JSC NPP Bourevestnik (St. Petersburg) in cooperation with Yakutniproalmaz Institute, for material size of -6+3 mm. In 2018, in-process tests of RGS-OD-3 X-ray sorter prototype on material size of -3+1 mm are scheduled. Studies to determine the content of low-luminescent diamonds and feasibility of their recovery using XRT-400 and XRT/D sorters at the Processing Plant #3 of Mirny Mining and Processing Division (MPD) were carried out. The results of the studies confirmed presence of such diamonds and possibility of their recovery using the dual-energy X-ray transmission method. In-process tests of RGS-2 X-ray graphic sorter were carried out at the Processing Plant #16 of Nyurba MPD. According to the results of sampling of RGS-2 sorter separation products, the recovery of -6+3 mm sized diamonds from tailings of X-ray luminescence sorters was achieved at the level of 96%, while the diamonds recovery was 98.5% in value terms, the concentrate yield was 0.1%. In-process tests of RGS-1M sorters at final recovery of the grease separation concentrate at the Processing Plant #3 of Mirny Division were carried out. Recovery of low-luminescent -6+2 mm sized diamonds by RGS-1M sorter amounted to 92.4% for single operation, and with the double control operation reached 99%. As a result, -6+2 mm sized base product recovery increased by 0.2%."

Jan 1, 2018

By T. C. Sun

Two wasted activated sludges (WAS), from an industrial wastewater treatment and a sewage treatment plant respectively, and 7 collectors are used to investigate the feasibility of air flotation thickening of WAS by adding the collectors used in mineral processing. The collectors experimented include straight chain fat acids with different chain length, sodium oleate, alkyl sodium sulphonate, sodium dedecylsulfonate, and dodecylamine. The results show that the thickening efficiency varied depending on different collectors. Of the collectors experimented, dodecanoic acid and dodecylamine are best collector for thickening both sludges.

Jan 1, 2014

By I. Yu. Rasskazov, A. V. Rasskazova, N. M. Litvinova, N. A. Lavrik, V. G. Kryukov

The possibility of the intensification of the gravity processing of complex iron-manganese ore, which contains the finely dispersed inclusions of gold and platinum is shown. Clear mineral fractions of precious metals were sorted out of the different types of ores (quartz-braunite and carbonate- magnetite ore, ferruginous quartzite, carbon-containing shale, breccia-limestone and dolomite breccia). Composition and structures of precious-metals particles was detailed. The industrial content of platinum and gold was found. Precious-metals mineralization is character for all types of ores. High content of platinum is indicated in the carbonate-magnetite (up to 11.3 mg/kg) and quartz –braunite (up to 10 mg/kg) types of ore. Gold is presented in the ferruginous quartzite (up to 1.29 mg/kg) according to the data of the reduced mineralogical analysis. The composition of native platinum depends on the type of the ores: 1) quartz-braunite type contains isoferroplatinum (Pt3Fe) with Cu, Rh, Ir, Ru; 2) carbonate-magnetite type contains isoferroplatinum with Cu, Sn, Ni, Rh, Ir, Os; 3) pyritic-carbon ore contains isoferroplatinum with Sn, Ni; 4) ferruginous quartzite contains isoferroplatinum without admixtures. The ultrasonic treatment of mineral aggregates (P = 41.5 Watt, I = 15 W/cm2) made possible the liberation of fine particles of precious metals. Smooth-shaped or crystalline mineral aggregates are effectively liberated after acoustic treatment. Their surface is freed from impurities. The aggregates with the complex form and structure, which consist of the numerous plates and the grains, are not effectively liberated from impurities. It is shown that the ultrasonic treatment of aggregates with the fine inclusions of precious metals contributes to the liberation of the particles of platinum and gold and intensification of the gravity processing of refractory ore. This approach contributes the increase of the raw-material base of precious metals.

Jan 1, 2018

By Rajamani R. K.

The design of tumbling mills has progressed from the Bond work index concept of the 1950s to the population balance concept of the 1980s and then made a quantum leap forward with the discrete element method in the 1990s. The failure of a SAG mill at the Grasberg mine site set in motion the inquiry into the role of shell lifter geometry on the profile of the charge motion within the mill. Quickly, it became evident that this could only be accomplished by tracking individual motion of ore particles and grinding balls and not by study of en masse motion of the charge that had been established previously. The discrete element method (DEM) which was prevalent in the civil engineering literature at that time proved suitable to tackle this simulation problem. In 1991, the two dimensional simulation of laboratory scale mills was validated with the DEM. Later this simulation method evolved into ?MillSoft?? a simulation software package for the design of lifters in ball and SAG mills. MillSoft?simulations proved that cataracting charge motion is not conducive to the life of lifters. The old rule of thumb that the number of shell lifter rows should equal twice the diameter of mill in feet was shattered by simulation results. Instead, the number of rows equal to the diameter of the mill in feet, providing that the lead angle of lifter is around 25 degrees, was established as being more optimal. This bold design change was first implemented and tested by Mark Sherman at Alumbrera Mines in Argentina. Two 36-ft SAG mills responded extremely positively to the design change. This success was immediately repeated at Collahuasi, Pelambres and other mines in South America. The design change has so far exceeded expectation that there is not a single SAG mill around the world today that does not employ a relief angle on its shell lifter. The DEM method has advanced in the hands of the author, mining companies and universities, notably in Australia and South Africa. Today, three-dimensional simulation of charge profile and slurry transport is a standard in the design of mills. There is strong pursuit of a virtual comminution machine with DEM in Australia. In South Africa, an experimental method known as positron emission tracking is emerging as a method for tracking particles in grinding mills. The computational burden of computing with millions of particles in three-dimensional simulations has been eased to less than a day with a technique known as GPU computing. Keywords: DEM method, GPU computing, SAG mill, tumbling mill simulation, discrete element method

Sep 1, 2012

By Nirmal Weerasekara, Malcolm Powell, Mohsen Yahyaei

"The conditions under which rocks become superficially damaged during the grinding process are not well understood. The main purpose of the work presented here is to understand how superficial breakage occurs under incremental low-energy impacts. To enable this study a series of abrasion tests with multi-size pilot mills have been performed. Outcomes of numerical simulation corresponding to each test were examined to investigate the experimental results. Abrasion tests have been conducted using three grinding mill sizes (i.e. 1.8, 1.2, and 0.8 m). Two types of ore were used to investigate different hardness strengths. To ensure abrasion was the dominant mechanism, in all tests the mill speed was reduced to 40% of critical speed. The relationship between the Fractional mass loss rate and particle size was investigated by randomly collecting seven tracer particles from sizes -73+63, -53+45, and -37.5+31.5 mm. It was evident from the results that the Fractional mass loss rate of angular particles declines as the particle size increases whereas the Fractional mass loss rate decreases from fine to coarse in rounded particles. Results of Discrete Element Method (DEM) simulations indicate that fine particles experience higher levels of collision energy per particle and this value reduces as the particle size increases and mill size reduces. This explains the higher Fractional mass loss rate of smaller particles as well as the increase in the Fractional mass loss rate as the mill size increases. Linked DEM and experimental data indicates that under these test conditions surface damage attrition is the dominant mechanism. This work suggests that DEM simulation can be implemented to predict the abrasion wear of particles in mills."

Jan 1, 2014

By P. Prakash

A dual-drive planetary mill, which has a rotating shaft that sweeps a circle of diameter 750 mm, has been designed. The planetary mill is powered by a 5 hp motor to rotate the main shaft and a 3 hp motor to rotate the jars. The charge dynamics inside the horizontal-axis planetary ball mill was established using three-dimensional DEM simulations. The simulation results provided data to determine the impact energy distribution and the effect of process parameters such as mill speed and filling. It has been observed that the mean impact energy per unit time increases with rotation-to-revolution ratio, whereas the average number of inter-particle impacts per unit time decreases. The mill was also used to synthesize a variety of powders. Here three case studies of reaction milling are briefly presented: (i) cementite and silicon carbide, (ii) oxide dispersed strengthened (ODS) steel, and (iii) magnetite from blue dust. In each case, the powder was produced by mixing and then milling the corresponding pure components. The phase evolution, particle size distribution, and morphology of particles during milling were studied for various samples collected at different milling times using laser size analyzer, SEM, TEM, and Mössbauerspectroscopy. The results established a convenient way to produce powders of high technological and commercial value.

Sep 1, 2012

By K. A. Natarajan

Involvement of various indigenous microorganisms in extracellular and intracellular iron oxide formation is a convincing index for iron ore biogenesis. Biomineralization of various iron oxides such as hematite, magnetite, goethite and limonite with the participation of aerobic and anaerobic microorganisms is well established. Various aerobic and anaerobic bacteria such as Gallionella, Leptothrix, Acidithiobacillus, Thermoplasmales, Pseudomonas, Bacillus spp and Shewanella putrefaciens, which are implicated in the formation of higher and lower oxides of iron have been isolated from different iron ore deposits. Diversity of microbial life in iron ore deposits can be put to beneficial use such as selective removal of undesirable constituents such as silica, alumina, clays, phosphorous and calcite and also to bring about environmental detoxification. Role of microorganisms such as Paenibacillus polymyxa, Bacillus subtilis, Yeasts and a sulfate reducing anaerobe in the biobeneficiation of hematite is illustrated. Surface chemical changes brought about by bacteria - iron ore mineral interactions are discussed with respect to hydrophobcity, adsorption isotherms, zeta potential data and bioreagents generation. Bacterial adaptation to minerals such as hematite, quartz, alumina, calcite, apatite and clays results in secretion of mineral ? specific biosurfactants such as proteins and polysaccharides. Such bioreagents can be used as selective collectors, dispersants and flocculants in iron ore beneficiation. Research results are highlighted to demonstrate silica, alumina, phosphate, calcite and clay removal from hematite. Environmental friendliness of such biobeneficiation processes is demonstrated with respect to biodegradation of toxic amine collectors, utility of ?in situ? organisms in enhancing settlement of fines in tailing dams and water harvesting. Keywords: bio-mineralization, bio-beneficiation, bio-remediation, Gallionella, Leptothrix

Sep 1, 2012

By L. Tavares

The significant capital and operating expenditure of size reduction operations have maintained comminution on the spotlight of mineral processing research during the last century and, more recently, the concerns about the impact of these operations on the sustainability of the minerals industry, will remain to do so in the 21st century. One of the most popular approaches that have been used to deal with these challenges is the application of simulation both to reduce the uncertainty in the design and improve the operation of size reduction operations. From the initially purely empirical approaches, including the energy size reduction ?laws? and the phenomenological approaches, of which the traditional population balance model is, arguably, the best example, comminution modeling now reached a point in which more fundamental and mechanistic models are sought. The paper analyzes some of the advances that now make multiscale modeling of comminution processes realizable. On the microscale, greater understanding of the phenomena involved in fracture and fragmentation of single particles under different stressing conditions now exists. Particle breakage testing methods are currently used in a routine basis by industry and good quantitative descriptions of different breakage mechanisms are now available, although research is still required to develop appropriate models for a couple of them. On the macroscale phenomena, the discrete element method (DEM) has been successfully used not only to provide insights but also quantitative information on the transfer of mechanical energy from the machine to the grinding media in mills and to particles in crushers, while smoothed particle hydrodynamics (SPH) and computational fluid dynamics (CFD) to describe fluid flow. The paper also analyzes the importance of modeling mesoscale phenomena in size reduction, which is the interaction of particles forming assemblies or beds of particles, demonstrating some of the areas requiring further attention. Examples of application of the multiscale modeling approach to the inadvertent comminution of ore lumps during handling, to the comminution in vertical impact crushers and tumbling mills are demonstrated. Keywords: comminution modeling, DEM, SPH, CFD, multiscale modeling approach

Sep 1, 2012

By Prasad Kopparthi, Narasimha Mangadoddy, Balraju Vadlakonda, A. K. Mukhurjee

"Column flotation (CF) is widely using equipment in mineral processing since many years. ERT technique facilitates non-invasive and nonintrusive visualization of different parameters in a column flotation. The hydrodynamic investigation of two-phase and three-phase are studied using electrical resistance tomography (ERT) coupled with pressure transducers in laboratory column flotation. Bubble size distribution, bubble rise velocity and gas and solids hold-up hydrodynamic parameters are extensively used for column flotation design and performance evaluation. The effect of superficial gas velocity, feed flow rate and slurry height in the column on mean gas holdup and its radial distribution has been analyzed for both two-phase and three phase flows. Influence of solid particles on gas hold-up and its complete elucidation of dispersion in the column are assessed. Experimental results show ERT coupled with PT is suitable as an online monitoring tool to provide useful information on the hydrodynamic parameters of the column flotation. The tomography images, which were generated using a modified sensitivity back projection algorithm, were employed to explore the parameter study in two phase flow in column flotation.Furthermore, the results also indicate that ERT is a very powerful tool for diagnosing the `inside' flow behaviour of gas-liquid two-phase and gas–liquid–solid three-phase flow in columns operating for a wide range of flow regimes.INTRODUCTIONColumn flotation is being widely used in mineral processing industries in last few decades. There has been a lot of attention in understanding the various mechanisms that take place during operation. Due to many reasons column flotation has been found to yield better performance than conventional flotation cells, particularly with fine particles (Honaker and Mohanty, 1996). Due to complex flow behavior in nature, the performance of column flotation influenced by on flow characteristics of the process, (Jena et al., 2008). Previously basic research is carried out to evaluate the effect of the hydrodynamic parameters on the performance of column flotation (Finch and Dobby, 1991)."

Jan 1, 2018

By Luis Bergh, Francisco Díaz, Isabel Panire, Juan Yianatos, Luis Vinnett

"In this paper, industrial data of residence time distribution (RTD) in mechanical flotation cells is presented, which were measured in several plants using the radioactive tracer technique. Results include mechanical flotation cells of 100 - 300 m3, which were operated with effective residence times from 2 to 7 min. Tests were developed in forced air and self-aerated cells for liquid and solids (non-floatable) per size classes. Different RTD model structures including perfect mixer, Large and Small Tanks in Series (LSTS) and by-pass flow plus perfect mixer were evaluated and compared for single cells. The actual mixing regime was related to the effective residence times and cell designs based on the model fitting. By-pass flow percentages were typically lower than 10%, therefore the perfect mixer model plus a dead time was a suitable model structure in most cases. On the other hand, the arrangement of cells in series was effective in reducing the bypass flow observed in single cells (by-pass flow percentage greater than 5%). In addition, the N perfectly mixed reactor in series model was used to represent the mixing regime along flotation banks, which were operated with mean residence times in the range of 18 - 53 min. Results showed that N tanks in series plus dead time were closer to the actual values in most cases."

Jan 1, 2014

By P. Hatefi, O. Rahmani, M. Noor-Mohammadi, A. Tohry

"Depressants play an important role in the selective separation of impurities from iron minerals by direct or inverse flotation. In this paper, sodium co-silicate (SCS) with chemical formula of Na4SiCO6, as a depressant with pH modifier features, has been synthesized and used for phosphorus bearing iron ore in anionic reverse flotation. In this process, phosphorus is floated while the iron oxides are depressed, using fatty acids as collector in an alkaline medium. Batch and pilot flotation tests were carried out to investigate the influence of SCS on the separation selectivity of phosphorus from iron oxides. Also the depression mechanism of SCS on hematite surface was investigated by microflotation tests and FTIR spectroscopy measurements. The flotation results indicated that without using a pH modifier, the pH of pulp could reach up to 10, when SCS was used as depressant. In this condition, a better depression performance was observed compared to sodium silicate (SS). Using the SCS, phosphorus and total iron content in iron concentrate was 0.046% and 66.29%, respectively, compared to SS where these values were 0.06% and 65.75%, respectively. As a result the weight recovery of iron concentrate was increase by around 4%, compare to SS. It was also found that 238 g/t of SCS could be used instead of 3 types of reagents collectively, including 32 g/t of NaOH, 151 g/t of Na2CO3 and 400 g/t of SS gel.INTRODUCTIONThe phosphorous presents in iron ore minerals is mainly in the form apatite mineral. The apatite is separated from iron ore minerals by magnetic and flotation methods (Ma, 2012). The reverse anionic flotation of iron is one of the most common method for removing phosphorus from iron concentrate (Araujo et al., 2005).Usually apatite minerals are readily floated using anionic collectors such as fatty acids (Ma, 2012). In this conditions the iron minerals are depressed and by modifying the pH in alkaline conditions, selective separation of phosphorus from iron concentrate can be achieved. Depressants including; sodium silicate (SS), starch, dextrin, guar gum and humic acids play an important role in the reverse flotation of iron ore (Kar et al., 2013; Ma, 2012; Turrer and Peres, 2010; Araujo et al., 2005). Studies have shown that SS has a better effect on iron recovery and phosphorous reduction, compared with other depressants (Tohry and Dehghani, 2016; Qi et al., 1992, Dho and Iwasaki, 1990). In most flotation processes, modifiers are used to adjust the pH. To achieve alkaline conditions, mainly pH modifiers such as carbon dioxide and sodium carbonate are used."

Jan 1, 2018

By Matt Kilburn, Liming Lu, Steve Suthers, Alexander Edenton, Rodney Smyth, Matt Adam

"Magnetite concentrate is naturally good for pelletising. However, due to the depletion of reserves of traditional high grade hematite iron ore worldwide, the usage of magnetite concentrate in sintering is expected to increase substantially. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. This will not only improve the quality of agglomerates produced, but also have a potential beneficial impact on the fuel consumption of the agglomeration process. There are an increasing number of magnetite projects currently being considered and developed. However the concentrates from some of these projects are too coarse as pellet feeds and much finer and denser than normal sinter feeds. Accordingly, special strategies are required in order to utilise the coarse magnetite concentrates at high proportions in pelletising and sintering. This paper discusses various raw material preparation technologies and blending optimization methods demonstrated to be effective for improving the sintering and pelletising performance of coarse magnetite concentrates. Pre-granulation and addition of binders, such as hydrated lime, were found to be particularly efficient in recovering the sintering productivity of sinter blends containing magnetite concentrates. In pelletising, HPGR (High Pressure Grinding Rolls) grinding enabled production of good quality pellets from 100% magnetite concentrates and optimized blends containing up to 70% magnetite concentrates also formed good pellets.INTRODUCTION Magnetite concentrates are often used as feed materials for pellet plants or sinter plants depending on their grades and grain sizes. To achieve the required quality of green and fired pellets, the concentrates often need to be ground very fine (80% passing 38- 45 m), which inevitably consumes a great amount of energy. Therefore, efficient grinding processes are required to reduce the amount of energy consumption needed to achieve the sizing and chemical specification of pellet feeds. The use of magnetite concentrates in sintering has the potential to improve sinter chemistry, which is deteriorating over time due to the slowly decreasing grade of direct shipping iron ores around the world (Yang and Mathews, 1997; Yang and Witchard, 1998, Yang and Davis, 1999; Yang 2005). However, methods are required to allow the utilisation of high levels of concentrates in sintering while maintaining productivity and sinter quality (Han and Lu, 2017)."

Jan 1, 2018

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone, has been successfully tested in the Platinum industry for dealing with the dense chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine chromite component in the final product. The dense media effect caused by a high chromite concentration in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size material in the float feed. The fine barren particles of chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.With the three-product cyclone a middlings product has been extracted that has a higher concentration of fine chromite. This volumetric stream flow represents a small percentage of the total cyclone feed and it is thus possible to treat it separately via fine screening to remove the fine chromite from the system and recover coarse silica."

Jan 1, 2003

By Ernesto de la Torre, Karla Velín, Alicia Guevara

"The following study shows the improvement and simulation of a gold recovery plant of 24 t/day of capacity by gravity concentration, flotation and leaching. The ore processed had grades of 6 g/t Au, 15 g/t Ag, and 0.69 %Cu with the mineralogy consisting of 2 %chalcopyrite, 12 %pyrrhotite, 7 %plagioclase and 50 %quartz. The recovery process starts with crushing the ore followed by grinding it further in a ball mill. The ground ore is then concentrated in a Falcon centrifugal concentrator with concentrate being processed by amalgamation process. Gravity tails are sent to a flotation circuit where the copper minerals and some gold are concentrated. Lastly, the flotation tailings undergo cyanidation for gold recovery. Currently, the overall recoveries are 82.8 %Au, 49.6 %Ag and 99.1 % Cu. The optimization was developed in the laboratory using a Wilfley table by gravity concentration. Flotation tests in the laboratory were performed using potassium amyl xanthate and pine oil. Lastly, cyanidation was then performed on the flotation tailings. The results showed the optimum concentration of sodium cyanide in cyanidation is 2 g/L, which produced an increase in gold recovery from 30% to 44%. The reduction of diameter particle from 132 to 80 µm also produces an incremental recovery of gold and silver from 11% to 21% Au and 0.4 to 3% Ag in gravity concentration. Likewise in the cyanidation the recovery of gold and silver has shown a rise from 44 to 62% and 8 to 32% for Au and Ag respectively. However, the flotation method the gold recovery is reduced from 68 to 30% Au by reducing the particle size. Computer simulations using the programs, Moly-Cop and ModSim were performed to determine optimum parameters for the recovery of precious metals at the gold recovery plant."

Jan 1, 2014