Search Documents

By Nikolas Schmitz

For today’s construction industry, large-diameter piles are common practice, as they are more competitive than drilling a larger number of smaller piles. More and more piles are installed by drilling rigs, replacing the installation by hammer, vibrators or caisson. Equipment capabilities and technics with rotary drill rigs are highly developed, but very costly and time-consuming when it comes to rock drilling, large diameters and deep foundations. Pile top drill rigs (PBA), based on reverse circulation drilling (RCD) technology, overcome these challenges and are an efficient solution for large diameter drilling (0.6 m to 8.0 m/19.7 ft to 26.3 ft) and drilling depths of up to 500 m (1,640 ft.)in various geological conditions onshore and offshore. The paper will explain benefits of RCD technology and prove this with figures from the Mumbai Trans Harbour Link project.

Nov 1, 2022

By Philip Derbyshire, Dale J. Scheffler

"Continuous Flight Auger (CFA) piling is a variation of Augered Cast-In-Place (ACIP) or augercast piling. In both cases a continuous auger with a hollow stem is used to drill a hole and a pile is formed by injection of cementitious material through the hollow stem as the auger is withdrawn. CFA differs from conventional American ACIP by the use of concrete rather than grout to form the pile, and by the type of equipment used to advance the auger into the ground and withdraw it. CFA installation uses a European style rig (i.e. fixed mast and rotary system) which can produce greater crowd and usually has a larger rotator or drill motor than the standard augercast setup. A standard augercast setup will consist of a lattice-boom crane and a set of leads to house the drill motor and auger. The auger size will range up to 24 inches (610mm). With CFA rigs larger diameter piles can be constructed, 24 to 36 in dia. (610mm to 915mm) are common and the technique has been applied with diameters up to 48-inch (1220mm). CFA makes use of sophisticated computer controlled monitoring systems, which have more recently been introduced for conventional ACIP piling. Developments in CFA have taken place over the last 25 years in Europe and particularly in the UK, but are relatively new in the USA. One application is in the construction of secant (overlapping) piled retaining walls. D.J. Scheffler Inc. recognized the potential of the CFA system following visits to the UK and has introduced its use into California for both secant piling and other applications.BACKGROUNDThe high price of real estate in many of the favored areas of California has increasingly led owners to want to build basements under their houses to increase the floor space available on a lot. Many of these areas are by the coast where the ground conditions are predominately granular and the water table is high. Conventional shoring and dewatering systems have often caused problems with adjoining properties. Clearly tangent walls are not suitable in these conditions because of leakage and loss of ground. The secant pile system, using CFA techniques, has proved very effective at overcoming the problems experienced by other methods. Other applications for CFA secant walls have included use for an emergency job on a highway following erosion caused by unusually heavy rainfall.METHODThe concept of secanting piles, whereby primary(female) piles are installed first and then secondary (male) piles are cut into the primary piles is not new. The method has been known for more than 30 years. Originally ‘Benoto’ grabbing rigs, developed in Japan, were used together with sectionalized double skinned casing and oscillators.This early method was slow, although very effective. More recently high torque rotary machines have been used. Contractors in the UK have increasingly used CFA techniques to further improve productivity of this type of piled wall. The improved capabilities of piling rigs available, as well as developments in concrete technology and instrumentation, have made this possible."

Jan 1, 2005

By Noreen Tarac, Pablo Forgoso, Philipp Schober

A multiple use storage facility building is being developed in the Philippines on a peninsula that was reclaimed in the 1990s without any soil treatment. The subsoil now consists of loose to medium dense silty sand underlain by a soft to medium stiff clay. A liquefaction assessment by analytical methods have shown that the loose to medium dense silty sand yields a high potential for liquefaction and lateral spreading during pthe design level seismic event. To mitigate the risk of liquefaction and lateral spreading, as well as assure the slope stability of the shoreline, a solution utilizing a combination of ground improvement techniques by means of a Mixed-In-Place (MIPTM) Lattice Grid Wall and Stone Columns was developed and successfully executed. For the detailed seismic design, a Finite Element 3D analysis was undertaken to simulate static and dynamic actions on the buttress wall. The liquefaction assessment and settlement calculation were carried out based on analytical design approaches. For the execution of the Lattice Grid Wall, the Mixed-In-Place (MIPTM) method developed by BAUER Spezialtiefbau GmbH was applied. The stone columns were installed using the Wet Top Feed method.

Sep 8, 2021

By Rob van Dorp

"AbstractThe Monitoring & Instrumentation Committee (MIC) of DFI Europe has the objective to support DFI members in concern of risk management of geotechnical matters, where monitoring and instrumentation have added value.Work of the CommitteeA study by the committee showed that there are already several existing (national) guidelines. They all have their strengths and limitations and their focus may vary a little per country due to local regulations and typical local building activities, but the main question remains what added value another new guideline would have. More likely it would add to the confusion instead of providing overview.Companies with larger experience in geotechnical monitoring (often larger consultancy firm, contractors or clients) are already quite familiar with its benefits do not really need a new guideline in how to design and effectively apply sophisticated geotechnical monitoring systems for special projects.Therefore the aim of the MIC is to focus a little more towards smaller organizations - that are less familiar with monitoring and instrumentation - and the more ‘regular’ type of project that they are mainly involved in. The MIC wants to create a tool which helps them to create risk awareness, to understand the benefits of geotechnical monitoring and to provide them information about how and where to find the right partners and equipment to setup and apply appropriate monitoring systems for their projects.Monitoring and instrumentation benefits are for example:• Risk control during construction stage;• Costs reduction in design and construction (taken limitation of geotechnical aspects into account).• Prevent of unnecessary delays in construction work• Increasing general awareness of geotechnical risks and possibilities of monitoring.The cost of monitoring compared to the cost of failure and/or the savings that can be achieved play a role in the work of the committee. DFI members benefit from the shared knowledge by the MIC on monitoring and instrumentation within their process of risk management."

Jan 1, 2014

By Dr Karsten Galipp, Kai-Julian I. Hendler, Prof. Manuel G. Pinheiro, Dr Peter J. Bourne-Webb

With a share of approximately 11% of global greenhouse gas emissions, the construction industry contributes significantly towards climate change. This is why construction projects should not only be assessed on costs and technical solutions, but also on their carbon emissions. Life Cycle Assessment (LCA) is a tool which can quantify the environmental impacts of a construction project over its entire lifetime. The objective of this study was to determine the carbon footprint of three types of quay wall structures, namely sheet pile combi-walls, open piled decks and caissons using an LCA approach. Each of these quay walls were studied under the same boundary conditions, such as design life, ground conditions, dimensions, location and so on. The analysis showed that the sheet pile wall has the lowest carbon footprint whereas the open piled structure has the highest. Furthermore, it could be shown that the largest share of greenhouse gases (approximately 80%) is emitted during the production of construction materials. The transportation of materials and construction activities each contributed under 12% to total emissions. The sensitivity analysis showed that with innovative approaches, such as adapting the concrete mix design, the carbon footprint could be reduced by 26% to 40%.

May 1, 2022

By David H. Sanders, Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Large-diameter drilled shafts (DS) are a critical part of a seismic-resistant system, and therefore it is important to be able to accurately model lateral resistance. To undertake the lateral load analysis of largediameter DS, a finite-difference p-y analysis program, NVShaft, is being developed at the University of Nevada Reno. Validation of the new program involved numerous p-y analyses using commercially available programs. Subsequent comparisons suggested the program's ability to yield reasonable predictions for typical diameter DS. Based on the I-15/US 95 load test program carried out in Las Vegas, NV, this study presents the evaluation of NVShaft in Nevada’s subsurface condition. Lateral load analyses of a 2 ft and an 8 ft diameter DS were attempted using NVShaft. The location of the applied lateral loads and the presence of cemented soil-layers were incorporated in the modeling. A good agreement between NVShaft prediction and the measured response was found for the 2 ft diameter DS. For the 8 ft diameter DS, a stiffer response was predicted. The inspections of the moment-curvature characteristics at different load levels suggested cracked response of the concrete due to prior axial load testing may be one of the reasons behind the deviation.

The intent of this manual is to provide guidelines for inspectors of drilled shaft construction otherwise referred to as drilled piers, caissons or bored piles. It should also be helpful to train beginning geotechnical engineers with limited first hand experience or for geotechnical engineers who are training inspectors. It is expected that the general guidelines and procedures described here will be supplemented by local geotechnical engineers working in a particular region based on local practice and experience. Since drilled shaft construction procedures vary widely based on local geology and size of project, an all-inclusive manual is not considered practical. This manual focuses on traditional topside inspection for routine drilled shaft construction. Other inspection and evaluation methods that rely on electronic equipment are available, but these methods require extensive training and experience in the interpretation of results. These more sophisticated methods of drilled shaft inspection and evaluation are common in construction, but they are usually provided by specialty subconsultants. The subconsultant will typically submit a report for each shaft, which will be reviewed by the geotechnical engineer. Other manuals are available to describe the electronic methods of drilled shaft inspection.

Jan 1, 2004

By Alexander Filotti, Richard Kalson

"In the last decade, the construction industry has witnessed significant changes in the project delivery systems and contractual relationships between the general contractors (GC) and Deep Foundation Specialty Contractors. The Deep Foundation industry, especially including industry specialty subcontractors, have experienced a significant increase in requests that project risks be transferred through contract documents to subcontractors and suppliers with a decrease in margins for the industry. GCs regularly revise their form subcontracts to take into account recent experiences/contractual trends and newly issued judicial precedent, an exercise that is less frequently undertaken by subcontractors and suppliers. These contradictory trends are at the base of the ethical analysis of subcontracts that comprises the subject matter of this paper. Using contracts as a risk management tool in order to mitigate the general contractor’s risks in the context of dynamic changes in the legislative environment will also be addressed. Furthermore, another possibility for risk mitigation for the industry is to actively promote the introduction of the latest technical developments into the contract documents.CONTRACTS’ ETHICSFor thousands of years, ethics have been a constant presence in our lives and have been debated by different branches of philosophy. In modern times, ethics in business started to be an imperative for the success of a globalized economy.“Ethics are standards by which one should act based on values. Values are code beliefs such as duty, honor, and integrity that motivate attitudes and actions.” (Rumbaugh 2004). Some of these values and actions have been carved in legislation in general and in business legislation in particular. More and more, unethical business practices (e.g., corruption) are identified as the root cause of poverty, underdevelopment, and war around the world. In the context of contract ethics, three aspects are of interest:•,Ethics of contract construction•,Ethics of contracting processes•,Ethics of risk allocation in contracts"

Jan 1, 2016

By Antonio Marinucci, Robin Mao

The new Hangzhou West Railway Station, which is currently in the early stages of construction, will be located in the city of Hangzhou, China. To accomplish the ambitious goals of the project, the construction work and station building was divided into three project areas. The original design utilizes 1,580 drilled shafts with diameters of either 800 mm or 1000 mm (32 or 40 inch) to support the new Station and its various ancillary structures. The drilled shafts will be tipped into the moderately weathered argillaceous siltstone a distance between 5 and 15 m (16.5 and 49 ft), resulting in an effective pile length ranging from 35 to 43 m (115 to 141 ft), respectively. For the first phase, approximately 550 production drilled shafts will be installed. Eight (8) sacrificial drilled shafts each with a diameter of 1000 mm (40 inch) were installed to a depth ranging from 50 to 57 m (164 to 187 ft), and were tested to confirm the design parameters used for the first phase, to evaluate the contractor’s installation means-and-methods, and to provide guidance whether redesign is warranted for the subsequent two phases. Bi-directional static load testing was performed using a donut-shaped Super Cell to apply unidirectional axial loads up to 13,200 kN (2,970 kip). This paper will describe the bi-directional testing and select results obtained therefrom. The axial compressive and uplift resistances determined from the testing verified that the available axial resistance of a single drilled shaft exceeded the minimum design requirements.

By Matthew E. Meyer

The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Castin- Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010

This manual is limited to Augered Cast-in-Place (ACIP) piles constructed using a hollow stem continuous flight auger. 1.1SCOPE AND LIMITATIONS The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Cast-in-Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010

By Marco D. Boscardin, Benjamin H. MacKinney, Kenneth R. Allard, Kenneth A. Pidgeon, Adriane G. Boscardin

This paper presents a case history for a unique application of a system of vertical micropiles with horizontal soil nail bracing and shotcrete facing for underpinning. The system was used to support and protect an existing 2-story hospital building during demolition and renovation. The goal was to limit building movements and have the building remain in use during construction of an abutting addition. Soils at the site consisted of clean, loose to dense, sand and gravel. The original underpinning design was revised after the initial excavation revealed unsuitable soil conditions for traditional underpinning pits. An alternative system consisting of vertical micropiles (hollow bars) through the footing, combined with shotcrete and soil nails was proposed, accepted by the owner, and successfully constructed. Excavation depths were up to 15 feet (4.6 m) below the existing footings. Wall movements were monitored at regular, horizontal and vertical intervals along the hospital wall, and less than 0.6 inches (15 mm) of settlement and 0.1 inches (3 mm) of horizontal displacement throughout underpinning and construction were reported. The challenges with the original proposed support of excavation design and other alternative approaches considered will also be discussed.

Oct 1, 2022

By M Muzammil, S. Mukerjee, S. Saran, M. Bharathi

"This paper presents the results of in-situ tests conducted on a set of under-reamed piles in a silty sand deposit. Three piles (i.e. vertical, vertical with one bulb and vertical with two bulbs) of diameter 0.2 m were cast upto a depth of 5 m. The pile cap had four foundation bolts cast into it so that a mechanical oscillatormotor assembly could be mounted centrally on it. The oscillator-motor assembly was used to generate purely sinusoidal dynamic forces, in either horizontal or vertical directions. For both horizontal and vertical vibration cases, it was observed that (i) the natural frequencies decreased with an increase in the excitation force level, (ii) for the same excitation level, the natural frequencies as well as the maximum amplitude of vibration are almost the same irrespective of the pile geometry i.e. number of bulbs in the pile, indicating that the full pile length is not being excited. For the vertical vibration case, the soil-pile stiffness at frequencies, before resonance, were observed to be higher than those at frequencies after resonance. In the horizontal vibration case, the stiffness of the soil-pile system was found to be decreasing with an increase in the excitation force level. The damping ratio was found to be increasing with an increase in the excitation force level.INTRODUCTIONUnder-reamed piles are piles, normally upto a depth of 6 m, with one or more bulbs along the pile stem. These have been used for structures like transmission towers, structures on expansive soils etc. for a very long time, however it is only in the last 30 years that dynamic response of a pile has been studied. Evaluation of dynamic soil-pile interaction is a very complex problem as the conditions and properties of soil are highly variable and unpredictable. Various models and approaches have been suggested by various investigators for evaluating the dynamic soil-pile interaction problem, but most of them are based on the assumptions that the behaviour of soil is linear and the soil surrounding the pile is strongly adhered to it. But in practice, it is not so. The soil surrounding the pile is always somewhat loosened and undergoes some deformation when a sinusoidal load is applied. This causes the soil-pile system to behave nonlinearly.In earlier studies by Novak, (1974), Novak and Aboul-Ella, (1978) etc. a linear elastic behaviour of soil was assumed. This approach was very useful in understanding the mechanism of soil-pile interaction to a large extent. Subsequently various models were suggested like the lumped mass models with nonlinear discrete springs, dashpots and friction elements Matlock et al. (1978), weak cylindrical zone around the pile model Novak and Sheta, (1980), ideal boundary zone model with non-reflective interface, Han and Sabin, (1995) etc. These approximate solutions give an idea about the mechanism of dynamic pile-soil interaction to a large extent. However, in reality both separation and slippage can occur due to the formation of a weak bond at the contact surface between the soil and the pile when a dynamic load is applied. In addition, the soil column adjacent to the pile experiences large deformations under dynamic loads and thus behaves nonlinearly.Some computer aided model studies on the dynamic response of under-reamed piles have been reported, however, very few insitu dynamic tests on under-reamed piles are reported. Dynamic tests on piles were carried out by Novak and Grigg (1976) on small scale single piles and pile groups in the field. Similar field tests on small scale piles were conducted to study the nonlinear behaviour of a single pile and a pile group under strong harmonic excitation by Han and Novak (1988), Han and Vaziri (1992), Burr et al. (1997), Manna and Baidya (2010) etc. The majority of these experimental studies were focussed on the response of the specific pile groups and compared with the results of a single pile. Hence there was a need to study the influence of pile g"

Jan 1, 2015

By Chris L. Powell, Russell J. Denny

"The remotely located Cockatoo Island iron ore mine off the Kimberley coast in the northwest of Western Australia has been in operation since 1951. The mine was recently expanded up to about 50 m (165 ft) below sea level using staged construction to create a rockfill seawall around the open cut mining operation. Late in 2013, to allow expansion of subsea iron ore mining operations, Wagstaff Piling was engaged to install a seepage barrier through the rockfill seawall and into the underlying seabed sediments.Earlier stages of seawall construction had used a variety of different construction techniques with varied success, and the history of subsea mining on the island had been plagued with failures, including failures in the slope of the seawall itself, hanging wall failure underneath and inside the seawall, and footwall failures as the ore was mined leaving the rock face inclined at 55 degrees, parallel to the bedding. The current expansion, known as the Stage 4 expansion, was more tightly constrained by the pit geometry and available materials than previous seawall expansions that adopted clay core and sheet pile seepage barrier solutions. In Stage 4, an innovative seepage barrier solution using a grout curtain was selected to provide the necessary cutoff to allow access to highgrade ore, while protecting the mine from inundation by the sea.Seawall ConceptThe open cut subsea mining operation consisted of a 3 km (1.9 mi) long narrow pit along the south side of Cockatoo Island that extended to depths of about 50 m (165 ft) below sea level, and were exposed to the open sea on the south side of the pit. Massive tidal variations of more than 10.5 m (34.5 ft) required a seawall founded on the seabed, extending upwards to RL+13, to safely protect the pit from the high tide level rising to above RL+10."

Jan 1, 2017

By Chris L. Powell, Russell J. Denny

"The remotely located Cockatoo Island iron ore mine off the Kimberley coast in the northwest of Western Australia has been in operation since 1951. The mine was recently expanded up to about 50 m (165 ft) below sea level using staged construction to create a rockfill seawall around the open cut mining operation. Late in 2013, to allow expansion of subsea iron ore mining operations, Wagstaff Piling was engaged to install a seepage barrier through the rockfill seawall and into the underlying seabed sediments.Earlier stages of seawall construction had used a variety of different construction techniques with varied success, and the history of subsea mining on the island had been plagued with failures, including failures in the slope of the seawall itself, hanging wall failure underneath and inside the seawall, and footwall failures as the ore was mined leaving the rock face inclined at 55 degrees, parallel to the bedding. The current expansion, known as the Stage 4 expansion, was more tightly constrained by the pit geometry and available materials than previous seawall expansions that adopted clay core and sheet pile seepage barrier solutions. In Stage 4, an innovative seepage barrier solution using a grout curtain was selected to provide the necessary cutoff to allow access to high-grade ore, while protecting the mine from inundation by the sea.Seawall ConceptThe open cut subsea mining operation consisted of a 3 km (1.9 mi) long narrow pit along the south side of Cockatoo Island that extended to depths of about 50 m (165 ft) below sea level, and were exposed to the open sea on the south side of the pit. Massive tidal variations of more than 10.5 m (34.5 ft) required a seawall founded on the seabed, extending upwards to RL+13, to safely protect the pit from the high tide level rising to above RL+10."

Jan 1, 2017

Jan 1, 2001

Jan 1, 1986

By Terrence M. Carroll, Chu E. Ho, Dimitrios Niarchos

"Construction of the new extension to Terminal 4 at John F Kennedy International Airport in Queens, New York involved the application of tapered piles for foundation support. Initial design based on past load testing experience had indicated that a pile depth of 65 feet was necessary to achieve a capacity of 394 tons. However, piles with a single length of 62 feet were ordered and installed, which led to marginal performance of the piles. This paper presents the technical considerations for mitigating the situation based on a systematic review of three preliminary pile load tests and dynamic capacity measurements on the shorter piles. Consideration was given to the long term gain in capacity of tapered piles due to set up in the Glacial Sand. The observational approach to the evaluation of piling performance adopted on this project resulted in salvaging many piles which failed to comply with the specified driving criteria. It was acknowledged that a more prudent course of action was for the Contractor to have ordered more appropriate pile lengths that allowed for potential variation in soil conditions across the site. The 4.6% saving in pile material did not warrant the effort that was required to mitigate the 39% of installed piles that did not meet the specified driving criterion.INTRODUCTIONAn expansion project at John F. Kennedy International Airport in Queens, New York involved the Phase 2 extension of Concourse B at Terminal 4. The site consists of 4 to 5 feet of pavement over about 10 feet of hydraulically placed sandy fill. Below this is a layer of marsh deposit, comprising of soft organic clay and peat, up to about 11 feet thick. Beneath the marsh deposits is a deep layer of glacial sand which extends to well over 100 feet below ground. Figure 1 shows the typical subsurface profile at the site. The new structures were supported on 223 steel tapered piles. The piles consisted of a straight steel pipe 18 inches in diameter and 0.375 inches thick, with a 25 feet long tapered bottom section (diameter varying from 18 inches down to 8 inches at the pile toe). The piles were first driven to the founding depth and subsequently in-filled with concrete. The concrete strength (fc) specified was 4,500 psi and the yield strength of the steel piles (fy) was 50 ksi. Initial pile design, based on earlier experience with static pile load testing for Phase 1 development at the same terminal, indicated that a pile length of 65 feet was necessary. However, piles with a single length of 62 feet were ordered and installed by the Contractor, leading to marginal performance of the piles. This paper presents the technical considerations for the adoption of alternative pile driving criteria, based on a systematic review of the preliminary static load test results for the present site and PDA measurements obtained during pile installation, in order to accommodate the capacity of the shorter piles."

Jan 1, 2017

By O. Craciun, C. A. Bridges, M. Cai, J. Sugawara

There are a number of methods that can be adopted for predicting the ultimate lateral resistance of a free-head rigid pile, from the conventional Brinch Hansen and Broms solutions to three-dimensional finite element analyses. Often these methods give rise to significantly different pile ultimate lateral capacities which could lead to either unsafe or too conservative designs. It is also well known that finding a rigorous and practical solution is challenging due to the complex three dimensional and nonlinear soil-structure interaction. This paper reviews some of the most common methods and produces results of pile ultimate lateral capacities embedded in cohesive or cohesionless soils. Subsequently, a finite element analysis is performed using PLAXIS 3D modelling under the same design conditions. Based on comparison of results, limitations and advantages are highlighted, and the most suitable method is proposed from a practical point of view.

Nov 1, 2022

By Brian D. Barkauskas, Terence P. Holman

A major combined nuclear and coal-fired power plant, located in on the western coast of Florida has undergone multiple upgrades in recent years to increase power output and enhance environmental controls. Construction of new elements within the existing plant structure required working in highly congested conditions and heavy crane lifts with large picking radii. The largest crane pick involved the use of an 1800 metric tonne capacity Mammoet PTC ring crane for a single long-radius, high altitude lift of a precipitator unit. Original bid tender documents had called for drilled shaft foundation support, but the presence of many critical utilities and unfavorable access for cost effective construction led specialty contractor Moretrench American Corporation to propose an alternate micropile foundation on the basis that high capacities could be achieved in the weak limestone geology and that the smaller size of micropiles would allow for more surgical installation in the utility-congested areas. This case history describes the design and construction of seventy three (73) high capacity micropiles for the value engineering alternative and the crane foundation for this critical lift. Each micropile was founded in a competent dolomitic fossiliferous limestone unit at typical depths of 23 m below existing ground surface. Strain gauge instrumented load testing was used to validate the geotechnical design parameters in the weak limestone bedrock and resulted in the finding that the entire test load was being carried in the upper half of the bond zone. Construction of the production micropiles required numerous relocations due to utility conflicts and local reanalysis and redesign of the 1.2 m thick reinforced concrete ring beam cap. Crane foundation performance was satisfactory and the effective life of this temporary foundation was only 6 months before decommissioning and demolition.

Jan 1, 2017