Search Documents

By Harald Ludwig

In 2002, excavation support work commenced on the Capitol Visitor Center project located adjacent to the nation?s Capitol building in Washington, D.C. The outlying work (Slurry Wall Work at Main Site is not discussed) consisted of providing excavation support for a new truck tunnel approximately 1900 feet long up to 50 feet deep as well as support for the new underground auditorium and Library of Congress tunnel. The excavation support consisted of a combination of conventional drilled in soldier beams, lagging, tiebacks and braces; intricate underpinning inside the existing Capitol building; support of an existing Russell Tunnel; soil nailing and tiebacks underneath the existing Russell Tunnel; two temporary bridges; and a deep soil mixed wall with lateral support provided by braces. As part of an on-going research program, some of these braces were instrumented with strain gauges. The deep soil mixed wall was approximately 300 feet long and 65 feet deep on either side of the truck tunnel. Approximately 34,000 sf of deep soil mixed wall, 90,000 sf of conventional excavation support, 200 braces, and 320 tiebacks were installed. This paper describes the large scope and breadth of the project that required a variety of excavation support techniques. A few of the challenges in designing and installing the support of excavation are discussed. This paper also presents the results of the instrumentation program conducted on the deep soil mixed wall, which stood open for more than a year.

Jan 1, 2006

By G. G. Goble

Significant progress has been made in the past decade in determining the load bearing capacity of pile foundations. Developments in the means of prediction of pile capacity as limited by soil strength have been substantial, particularly in the use of dynamic methods. The use of currently available equipment, analytical procedures, and practices in the field, will often produce material economies on a job by allowing increased loads with proven factors of safety. This approach justifies the minimum number of piles required for a safe foundation in a wide range of job sizes and soil conditions. To avoid exposing the reader to excessive detail in the body of this paper, technical topics have been covered more thoroughly in several appendices. I. Wave Equation Analysis of Piles Appendix A II. Dynamic Monitoring and the Pile Driving Analyzer Appendix B III. Case Method Capacity Calculation Appendix C IV. Case Pile Wave Analysis Program Appendix D 1 Preliminary Analysis In designing driven pile foundations, there must be a close relationship between design, construction control procedures, driving practices, and the size of the job. Small commercial buildings or residences involving loads that are only a fraction of the pile capacities do not justify the expense of detailed design processes or elaborate construction controls. Nevertheless, some preliminary analysis of the job requirements and a limited subsurface investigation must be made to understand existing conditions and the possible foundation solutions. In other words, it is necessary to determine that driven piling is the best overall choice of foundation.

Jan 1, 1988

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

By Richard D. Short

The Pseudo Static Pile Load Test, PLT, is a rapid method for determining pile capacity. Pile design is usually based on theoretical calculations of ultimate load capacity using soil data from a field investigation. The pile capacity is confirmed during construction by analysis of blow counts using dynamic formulae, dynamic pile monitoring, and load testing. Load testing is the most direct and reliable method of determining the actual capacity of a pile. Conventional load testing procedures, however, are time consuming and expensive. A typical load test requires installation of two to four reaction piles, construction of a high-capacity steel test frame, hydraulic jacks, and dial gauges, and will typically take one to three days per pile. Costs for load tests range from $10,000 to $20,000 per test. The Pile Load Test machine features a 25-tonne weight mounted on a mobile test frame. PLT load tests can be performed in a matter of minutes once the equipment has been mobilized to the site. This paper examines three test sites where the PLT test method was used and compares the results to conventional load test results and theoretical capacity calculations.

Jan 1, 2000

By Jean-Pierre Hamelin

Ground movements induced by underground excavation are always of critical concern, particularly in urban areas. Compensation grouting now appears as a safe means to control these movements. The paper presents new advanced systems developed by the specialist contractor to bring, at all stages of the project, an efficient control of operations and presents a case history taken from the project at Tren Urbano, Rio Piedras Section, constructed beneath an historic commercial section of San Juan de Puerto Rico.

Jan 1, 2000

By Andy Schroeder

Located in Hamilton, Ontario Canada, Berminghammer Foundation Equipment, is a manufacturer of advanced foundation equipment with 30 years of experience. The company is represented in more than 20 countries world wide, maintains an extensive Research and Development team, and has earned a reputation for finding the most practical solutions to the most challenging projects. The vertical travel lead, referred to as "VTL" system, was first developed and patented by C.W. Bermingham in the 1970's. This lead system was developed in response to the fundamental limitations of either a fixed lead or hanging lead system. The fixed lead system is well suited to level job sites with few obstructions and has the advantage of faster positioning of the lead, the hanging lead is very adaptable to different elevations and batter piles but takes much longer to position. Therefore the Vertical Travel Lead was developed to combine the advantages of fixed leads, fast and accurate positioning, with the ability to adjust the height of the lead base up or down. The VTL lead is connected to the boom by a sliding connection which allows the lead to be elevated or lowered below grade. The advantages of the VTL system were recognized by many foundation specialists and they have become the Industry standard in Canada , US Railway Construction , and many parts of the USA.

Jan 1, 1997

By Clyde Baker

Drilled shafts for many situations offer an economical alternative to driven piles. The Federal Highway Administration (FHWA) has spent considerable time and money in research and developing design and construction guidelines for drilled shafts. However, the full potential of the technology may not be realized because of the uncertainty of the effects of construction on the actual service behavior and the lack of either reliable quality control tests to check for or evaluate defects, or inexpensive load test procedures. Static load testing is very expensive and it is not feasible to load test each shaft on a project. Therefore, other means are necessary to confirm or evaluate the integrity of the completed drilled shaft or to determine the capacity of the completed shaft.

Jan 1, 1989

By A. Eslami

In recent development of piled raft design, the contribution of both raft and piles to tolerate the loads is taken into account, depending on the stiffness and contributions of involved elements i.e.; piles, raft and surrounding soil. The piles are usually required not to ensure the overall stability of the foundation but to act as settlement reducers. One alternative method of foundation design is therefore to introduce piles purely as a means of improving or enhancing the stiffness of the base soil by structurally disconnecting the piles from the raft. In this paper, two and three dimensional finite element analysis of disconnected pile-raft systems are performed on three case studies including a 12-storey residential building in Iran, a 39-storey twin tower in Indonesia, and the 256m height of Messeturm tower in Frankfurt, Germany. The analysis include different geometrical parameters, e.g., pile spacing and embedment length, arrangement and raft thickness for foundation system to obtain the optimized design functions and to clarify the role of each parameter and method of analysis. The parametric study results and comparison to a few field measurements indicate that by concentrating the piles in the central area of the raft foundation leads to the optimum design with the minimum total length of piles. This achievement can be considered as a criterion for project cost efficiency. On the other hand, disconnected piled-raft systems can significantly reduce the settlements and raft internal bending moments. Finally, the comparison indicates that simple and faster 2D analysis has almost the identical results to 3D analysis which is complicated and time consuming.

Jan 1, 2008

By Joram M. Amir

Even when they are cased! [ ] In bored piles, as well as in drilled shafts, and in caissons too, defects will occur! [ ]

Jan 1, 2001

By Charles H. Dowding

Whenever piling vibrations are significant, construction activities associated with pile driving and/or excavation can produce permanent displacement. These permanent displacements are more detrimental to structural performance than the hair sized, cosmetic, plaster cracks that might be produced by slightly exceeding reasonable vibration controls. Case studies are presented which demonstrate the relative importance of permanent displacements compared to directly produced transient vibration displacement within a horizontal distance of one pile length. Special attention is paid to settlements produced by densification of liquefiable sands. SOURCES OF TRANSIENT AND PERMANENT DEFORMATION DURING CONSTRUCTION Confusion over multiple sources of facility deformation caused by adjacent construction complicates the discussion of the relative importance of vibration induced cracking. None of the recent scientific investigations of vibration induced cracking (Siskind et el, 1980), involved deformation other than that produced by ground vibration from rock blasting. Thus these studies carry the implicit assumption that no ground deformation occurred other than that produced by the transient vibration. In other words there is no permanent deformation other than that which is typical of the older residential structures investigated.

Jan 1, 1991

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shafts (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, including the post-grouting of all drilled shaft tips. ? Design and construction of the scour protection for the two main pylons. ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2007

By George Piscsalko

There are numerous methods currently available to assess the integrity of drilled shaft and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity of drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube, or from embedding thermal wires within the shaft. This Thermal Integrity Profile method will be described in detail and one case history will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

Jan 1, 2011

By Anthony H. Tawil

Modern, high-speed machines used in the manufacture of paper require foundations with stringent settlement constraints. To fulfill this requirement, caisson piles, extending into bedrock, were selected to support a paper machine in Baie Comeau for the Quebec North Shore Paper Company (QNSPCo.). This was the fourth machine in an existing paper mill, and its construction was part of an expansion program which included the building of associated structures such as a wood room and chip storage building, and other facilities, Figure 1. The paper mill in Baie Comeau, Quebec, is located in an area which has extensive deposits of sensitive marine clay which are transformed into a viscous liquid when disturbed by external forces such as the driving of piles. Loss of ground and soil disturbance as affected by piling activity assumed considerable importance in the design and construction of the caissons particularly in view of the proximity of existing plant facilities, including another paper machine.

Jan 1, 1987

By Shawna Munn, Jakub Hudler

This paper outlines the use of tunneling headwall softeyes for transit construction projects in the Greater Toronto Area (GTA) over the past decade. Due to spatial constraints, tunnel boring machines were used to construct the underground tunnels requiring the design of launch and exit shafts with headwall softeyes to facilitate tunneling operations. Variable ground conditions and shaft geometries lead to the development of innovative headwall and tunnel softeye design applications using fiber reinforced polymer (FRP) elements (beams, reinforcing bars, and tiebacks). This paper outlines the challenges and benefits associated with designing and constructing shafts using various systems. Lessons learned throughout design and construction of more than 20 structures over the past 10 years are outlined. The constructability challenges with using FRP and design performance are also discussed. For over a decade, the City of Toronto has been expanding its metropolitan transit network with a variety of new transit construction projects. Two recent projects in the Greater Toronto Area (GTA) for underground infrastructure include the Toronto York Spadina Subway Extension and the Eglinton Crosstown Light Rail Transit project. These add a total of 31 new stations and 18.6 km (11.5 miles) of underground transit (TTC 2017) (EllisDon 2016). Due to ground conditions and spatial constraints of existing surface infrastructure, these projects utilized tunnel boring machines (TBMs) to construct the underground tunnels requiring the design of various types of shafts and headwalls to facilitate underground tunneling operations. To allow for tunneling through the headwalls, these shafts were designed with “softeyes” - a section of the wall without metal reinforcement that allows the TBMs to tunnel through.

Jan 1, 2018

By Giuliana A. Zelada

This paper reports on a study of 43 compression load tests (five fully instrumented) and ten pullout tests of auger cast-in-place (ACIP) piles in sand. Eight design methods reported in the literature were used to predict the measured pile capacities. Ultimate load capacities of the ACIP load tests were determined using two different definitions of ultimate capacity and compared with predictions. Load transfer behavior was determined from a study of the fully instrumented pile tests and compared to predicted values. Recommendations are made regarding the design approach most appropriate for these foundations and the best procedure for estimating ultimate capacity from pile load tests.

Jan 1, 2000

By A. Frits van Tol, Rodriaan Spruit, Jan H. van Dalen

"Abstract In recent years, there have been major problems with deep excavations in urban areas supported by diaphragm walls. In some cases, like the fatal Nicoll Highway collapse in Singapore the quality of the D-walls was not the cause. However in other projects, like the problems with the major leak in the walls of the Boston Big Dig and with leakage in a few projects in Belgium and The Netherlands was related to poor D-wall quality. Leakage through the D-walls at the joints in deep excavations led in these cases to very serious settlement behind the walls, in the case of the North- South line in Amsterdam, there was severe damage to historical buildings. This paper describes ongoing research that focusses i on acquiring more knowledge on and improvement of D-wall installation, in particular the flow process prior and during casting ii on the detection of anomalies prior to excavation and iii on the composition of the concrete mixture in view of a better and more sustainable concrete quality of D-walls.INTRODUCTIONIn the case of deep excavations in urban areas close to neighbouring buildings, diaphragm walls are one of the best feasible solutions for the retaining structure. Although the costs of D-walls generally exceed the costs of alternative wall solutions, the advantages are decisive in many situations. The main advantages of D-walls are the limited impact of the installation on the built environment, the high stiffness and bearing capacity and the retention of water, even at considerable depths. This makes Dwalls often the preferred solution for deep excavations Sometimes the D-walls are the temporary support while for the final stage a complete concrete box is constructed in the excavation. In many other cases the D-wall has the permanent function of retaining soil as well as groundwater.In the last ten years, there have been major problems with deep excavations in urban areas supported by diaphragm walls. In some cases, like the fatal Nicoll Highway collapse, 2004 , the quality of the Dwalls was not the cause. In other important failures like the collapse of the Archives in Cologne, 2008 and Dubai Infinity Tower Flooding, 2007 a combination of design and quality issues played a role. However, the major leak in the walls of the Boston Big Dig was related to poor D-wall quality (McNichol, 2000). Van Tol et al, (2010) describe a number of case studies in Belgium and the Netherlands, with leakage through the D-walls at stop end joints. In several cases with deep excavations these leakage caused serious surface settlements behind the walls. In the case of the North-South line in Amsterdam, there was severe damage to historical buildings. All these cases have generated considerable additional costs and delays, and subsequently public and political concern. Van Tol et al. (2010) present several possibilities to improve the quality of D-walls.Other disputes related to D-walls deal with the quality of the concrete and the sustainability of D-walls applied as a permanent wall. In particular the porosity of the concrete cover is sometimes problematic."

Jan 1, 2014

By Hou Shitao

With the development of Wuhan's city planning in China, new buildings of moderate and high store have been increasing day by day. Precast concrete piles or cast-in-site piles were used in the major foundations of the buildings. In process of their design and construction geotechnical engineers are concerned very much about practical bearing capacity and construction quality of pile foundations. In order to grasp accurately the cases static loading or vibration test is used generally to judge them. At present, the major questions in existence are that although a load is applied directly on pile and measured datums are reliable for static loading test, it must take a lot of work and longer time and engineering cost is higher. A vibration test has the advantages of which checking up of pile quality can be performed rapidly, the test is simple and convenient, and scope measured wide. But bigger error exists generally in measured datums. Therefore, it is nesessary to make vibration test on piles more perfect for pile foundation engineering. It is stated in paper that adapted technique of vibration test on piles is quite right in developmental direction sense for pile foundation. There are a great variety of vibration test methods on piles. A few of methods which often are adapted in practice can not meet the need of different practical engineering. It is also an important question whether the instruments of vibration test and relevant computer softewares make a response accurately for practical case. Different sequence of operation and technical requirements comes into being some influence directly on the test results. Meanwhile, different combination of soil stratigraphy, soil texture, groundwater and pile could cause different error of test datum. It is necessary to analyse and judge objectively the results of vibration test. Therefore, on the basis of developing and perfecting further the technique of vibration test, the applied technique of vibration test should be standardized so that better test results can be obtained.

Jan 1, 1991

By Donald Bruce, Mark Harris, Wesley Schmutzler, James Sanders

"This paper evaluates the history, construction and most importantly the performance of two remedial seepage cutoff walls installed in two major dams in the United States. Beaver Dam, on the White River in northwest Arkansas, was completed in 1966 and seepage through the karstic limestone under the embankment was apparent almost immediately upon filling of the reservoir. Several attempts to stop the seepage by grouting were unsuccessful. In 1994 a cutoff wall consisting of secant piles drilled with 32"" diameter down-the-hole hammers to a maximum depth of 185'?was completed and the seepage was reduced to a negligible amount. It has been over 20 years since the completion of the cutoff wall, and all indications are that the cutoff wall is performing as expected. Walter F. George Lock and Dam on the Chattahoochee River near Fort Gaines, Georgia, was completed in 1963 and suffered the same problem as Beaver Dam due to the limestone on which the dam was founded. Cutoff walls were installed in both embankments (1980s) and solved the problem in these areas, but under-seepage at the concrete lock, dam and spillway structures increased to the point that remediation was essential. The cutoff wall had to be installed through 110'?of water and another 100'?into rock upstream of an active dam that continued to generate electricity during the construction of the cutoff wall. A secant pile wall, in combination with a diaphragm wall, was completed in front of these structures in 2004. It has been over 10 years since the completion this cutoff wall and, again, the cutoff wall is performing as expected. The paper describes the construction of these cutoffs, but focuses on the long-term performance in terms of controlling seepage and piezometric levels.BEAVER DAMBeaver Dam is located on the White River, 609 miles above its mouth, in Carroll County, Northwest Arkansas. The construction of the dam and Beaver Reservoir was authorized on September 1954 by the Congressional Flood Control Act for purposes of water supply, flood control and hydroelectric power generation. The dam site was selected in 1957: construction began in November 1960 and was completed in June 1966. (FIG. 1)"

Jan 1, 2017

By Clyde N. Baker

Foundations for the Sohio Corporate Headquarters in downtown Cleveland have column loads of 11,400 kips, which increase to 15,000 kips with wind loading. An extensive exploratory program was conducted and comprehensive studies made to select the economically dependable support for the 46-story structure. A test on bond or socket friction for the caissons has usable values.

Jan 1, 1984

By Kanchan K. Sen

The North Shore Connector (NSC) project will extend the Allegheny County Port Authority?s Light Rail Transit System from downtown Pittsburgh below the Allegheny River to the North Shore via twin bore tunnels. Jet grouting, diaphragm walls, and soil mixing were selected as cost-effective technically viable ground improvement and support of excavation techniques. Jet grouting was specified to provide break-out (egress) and break-in (ingress) block sections at the tunnel boring machine (TBM) launching and receiving pits. Jet grout treatment was also used adjacent to buildings with shallow foundations and below retaining walls along the tunnel alignment. A new method for measuring jet grout column diameter based on electrical resistivity was employed on the project. New equipment was introduced in the U.S for constructing soil mix temporary support of excavation using a soil-mix technique termed Cutter Soil Mixing (CSM) due to the use of two vertical cutting wheels that have evolved from diaphragm wall trench cutter technology. The system allows for continuous water tight soil mix panel construction including steel beams. This paper highlights some applications of jet grouting and various support of excavation systems (e.g. slurry walls, cement bentonite walls and CSM walls), including new innovative techniques (e.g. Cyljet and CSM) used under the constraints of an urban environment.

Jan 1, 2010