Search Documents

By Michael D. Justason

"In January 2009, long-time competitors, Anchor Shoring & Caissons Ltd. of Toronto and Bermingham Foundation Solutions of Hamilton, joined forces to tackle one of the Greater Toronto area’s largest deep foundation projects: the West Toronto Diamond Rail Grade Separation. The two companies formed the “West Diamond JV” and succeeded in winning the contract from the Canadian National Railways. This deep foundations work was the first and most significant part of the $300-million-plus rail grade separation project. A big part of the job turned out to be dealing with local government regulations and citizens’ concerns with noise and vibration.The project is approximately 10 km (6 mi) northwest of downtown Toronto in an area of mixed-zoning including light industrial, commercial and residential buildings. The area is commonly called the “The Junction,” because of the heavy rail- traffic. The “West Toronto Diamond” refers more specifically to the railway junction where the North-South tracks of Canadian National (CN) Railway meet at a level crossing with the East-West tracks of the Canadian Pacific (CP) Railway. The goal for this part of the project was to convert the West Toronto Diamond into a grade-separated junction by depressing the CN lines under the CP lines, thus allowing commuter rail carrier, called GO Transit, intercity carrier VIA Rail, and CN freight trains to pass through the new underpass.Dawn Tattle, president of Anchor Shoring & Caissons says, “not only is the site in a densely populated area adjacent to homes and businesses, the crews worked adjacent to active rail lines with numerous trains passing daily. During the 7-hour working day, approximately 60 trains passed through the site in very close proximity to working crews.” Safety was paramount. While trains were passing through the site, it was a railroad requirement that all equipment and men stop working. In addition, at those times, all personnel were required to stay 6 m (20 ft) from the tracks and were required to face the tracks. For the faster commuter trains, this work interruption could last as little as 2-3 minutes, while interruptions caused by the slower freight trains could last as long as 25 minutes. The most disruption to the site occurred during the morning commute between 7 to 9 a.m., so work did not really get underway until after that time. Once work finally commenced the race was on to finish as much as possible before the afternoon commute – hence the shortened work day. The amount of disruption caused by the trains was a big unknown faced by the JV going into the project, but crews adapted quickly to the very unusual work environment"

Jan 1, 2012

By Javankhoshdel Yacoub

Piles are often used to reinforce slopes as they increase the available restoring force when calculating the factor of safety against sliding. In this paper, a 3D model of a slope containing multiple modes of failure is reinforced using pile elements. The results of the 3D Limit Equilibrium analysis containing piles are obtained using a newly introduced coupled approach which combines the results of finite element analysis (to obtain the displacement of soil along the pile) with the traditional limit equilibrium iterative formulation. The multiple modes of failure are obtained using the novel Multi-Modal Optimization (MMO) metaheuristic method which adapts the Particle Swarm Optimization (PSO) method to search for multiple local minima in a single slope model.

Oct 1, 2022

By Dominic Parmantier, Jason Page

"In the past, the designers of DSM have analyzed various failure modes and then specified a minimum unconfined compressive strength (UCS) for the soil-cement. The specified minimum UCS reflected the compressive stress in the soil-cement under design loads and an appropriate factor of safety. With the increased use of finite element analysis for the design of DSM applications where allowable strain as well as stress are considered, there is a growing trend for designers to specify a modulus and occasionally a tensile strength for the soil-cement in addition to the UCS. This paper compares the relationship of modulus and tensile strength to UCS for soil-cement from a recent DSM project with unique testing requirements. These results are compared to published data. The case is made that designers should utilize published relationships to characterize the required strength and stiffness by a single acceptance criterion: UCS.INTRODUCTIONAs the use of DSM has increased in popularity so has the use of service state deformation analysis in lieu of more traditional failure mode analysis. Most DSM designers are interested in the appropriate modulus values and occasionally tensile strength values of soil-cement as well as simply the unconfined compressive strength (UCS) of soil-cement.Although there are numerous published correlations between the UCS, tensile strength and modulus of soil-cement, some DSM project specifications are produced which have acceptance values for tensile strength, modulus, and UCS. If this specification of multiple strength properties is consistent with the nature of soil-cement, then there is really no harm except for the expenditure of client money on unnecessary testing. If however the multiple strength properties specified are inconsistent with the material properties of soil-cement, then the specifications can create the expectation that the DSM contractor can somehow create a custom soil-cement with tensile strengths and modulus characteristics which are unachievable.This paper presents a brief summary of a project in Burnaby, B.C. which specified minimum values for the tensile strength, modulus, and UCS of the soil-cement. A comparison of those test results to published correlations between the UCS and the tensile strength is presented. Additionally, a comparison of modulus derived from two different methods of testing is presented along with a comparison to published correlations between UCS and modulus for soil-cement."

Jan 1, 2015

By James Coull, Brian Wilson, David Siddle

"In 2012, Golder Construction Inc. was awarded a Design-Build contract for the design and construction of an extensive, deep ground improvement scheme to support up to 20 metres (66 ft) high Mechanically Stabilized Earth walls and bulk earthworks required for the development of the proposed Kitimat Liquefied Natural Gas (LNG) facility at Bish Cove, British Columbia (BC). Utilizing Cutter Soil Mixing (CSM) to construct barrettes consisting of overlapping rectangular panels of in-situ cement-treated soils, a deep mixing scheme, covering an area of approximately 12,900 m2 (15,430 yd2) and comprising some 1645 CSM panels to depths of up to 30.7 m (101 ft), was developed to provide the required static and seismic stability for the LNG structures, and meet the project-specific performance criteria.CSM panels were constructed through varying thicknesses and discontinuous layers of fine-grained, very soft to soft marine deposits, and loose to compact sands, with occasional interbeds of dense sands and gravels. Panel completion criteria was based on soil response factors, as measured by the CSM equipment, with the design requiring a typical embedment of about 2 m (7 ft) into dense silty sand to sand and gravel to provide the required bearing. A total volume of approximately 73,900 m3 (96,660 yd3) of soil was treated with cement to consistently yield average unconfined compressive strengths exceeding 2.5 MPa (363 psi).This paper outlines the challenges associated with the construction and quality control of this large deep mixing scheme in highly variable geotechnical conditions at a remote location with barge-only access, and limited communication facilities. Specifically the paper will discuss the logistical challenges faced and solutions adopted for the project; equipment redundancy requirements for a 24/7 operation; the impacts of wear and tear, as well as variability in subsurface conditions on productivity; quality control processes adopted for the project, including the value of provision of an on-site laboratory; and materials handling issues, and their impacts on mix design and quality control."

Jan 1, 2017

By Danielle Nhanqulumanga, Pranith Bhatt, Snehal Patel, Khadeeja Priyan

The Bi-Directional Static Load Test (BDSLT) is a test that determines the capacity of piles when loaded under bi-axial static compression. In recent years the BDSLT has seen an increase in demand due to its safety, speed, and affordability. This innovative foundation testing method has been universally used over the last 50 years, however respective codes and standards have only been published within the recent years. Detailed test procedures and methodology are expatiated in the ASTM D8169 M-18 [1], and the IRC 78 2014 Clause 709.2.5. [2] These standards provide the minimum requirements for the execution of the BDSLT. In this paper we did a comparative study of both standards envisaging to bring attention to the similarities and discrepancies found therein, with an aim to highlight the impacts and challenges that differing provisions of each standard could pose on the conduct of the BDSLT. Discrepancies found have been explained on the basis of geotechnical engineering theories and relevant field occurrences observed by superior engineers. Additionally, we emphasize on the relevance of experienced engineer’s judgement when utilizing the standards.

Sep 1, 2022

By A. Ortigão, M. Felix, E. Falk, T. Koehler

"Ground improvement techniques such as vibro-replacement or deep soil mixing are fairly young products in the Brazilian geotechnical market. Soft soils in this country are deep, very soft, have low sensitivity and are challenging. In general, ground improvement techniques are increasingly selected as more costefficient and flexible solutions on infrastructure projects compared to the conventionall technologies such as piled embankments, wickdrains with surcharge or jet-grouting. The geotechnical challenge expansion project for the Porto Alegre Airport, South Brazil, involved a taxiway area of five ha of 8 to 10 m of soft clay deposit. The deep soil mixing (DSM) technique was selected as a cost-effective solution to reduce settlements. As part of the design, an extensive soil investigation programme includ ing laboratory and field trials was carried out to define the most economical slurry-recipe, DSM installation patterns and quality control specs. This paper gives details of the field and laboratory trials and present results.INTRODUCTIONThe International Airport of Porto Alegre in the state of Rio Grande do Sul in Brazil is located in an area with extensive sediments near to Guaíba Bay. During the different construction phases of the airport over the last decades, the soft clay deposits have been a challenge for the local geotechnical community as well as for the specialized contractors (Schnaid et al, 2001). As part of the most recent expansion scheme, a cargo-terminal with a five ha airplane tarmac area will be constructed."

Jan 1, 2015

By Lenin T., Madhav M. R., Padmavathi V.

Use of PVDs and preloading on the ground can significantly reduce the time taken for ground to consolidate. Many soils in situ are lightly overconsolidated, with overconsolidation ratios (OCR) ranging from 1.0 to 2.0 due to various reasons such as glaciation, ground water level fluctuation, aging, cyclic loading, creep, erosion, cementation, etc. The effects of overconsolidation ratio are analysed in this study. Compression index and consolidation coefficient are important parameters in determining time – settlement response of soft soils under preloading and with PVDs. These parameters are typically estimated using oedometer tests on samples, with the assumption that the results represent the entire deposit. The in-situ time-settlement plots at different depths are used in the back analysis for estimating compressibility and consolidation parameters of in situ ground, resulting in more representative values that reflect the deposit's overall behavior. From observed time versus settlements plots, variations of compression index and coefficient of consolidation with depth of a deposit are presented. Estimation of compression index with depth is possible based on different OCR values as shown in this study. Barron (1948), Asaoka methods are used to estimate the coefficient of consolidation with flow in the radial direction.

Sep 1, 2022

By Rahul Wankhade, Sunil S. Baswankar, Aditya S. Kharatkar

Despite advances in pile design methodologies and piling techniques at site, difficulties and uncertainties still exists for design of piles particularly in coralline deposits and weak carbonate rocks. Such deposits are known to be heterogenous in nature, and occupy major stretches of earth, where piling experiences are probably very scanty. Such deposits are associated with low unit weights and usually consist of weakly cemented calcareous and carbonate soils interbedded with coral rocks containing cavities, which are completely void or filled with coral debris. Many of the studies indicate that conventional parametric relationships are may not apply to such sediments and rock formations. This paper intends to provide an appraisal of the available information that cautions against risks involved in conventional design practice and also serve as a guideline for pile design in such formations despite being a grey area of research. Contents of the paper is expected to provide a basis for the pile design and likely to serve as an eye-opener for research into this important soil-pile structure interaction problem.

Sep 1, 2022

By Rob Jameson

"Although seismic retrofit is recognized as a key micropile application, widely-used reference documents do not clearly address design and testing recommendations for micropiles that are loaded primarily under seismic conditions. The principles of micropile design and construction and their application to seismic retrofit projects are well understood and executed by leaders in the field. As the micropiling market grows, a wider audience relies on the information presented by DFI and similar industry groups. State-of-practice updates appear periodically in conference proceedings, but examination of recent bid documents makes it clear that there are opportunities to improve the specification of load, deflection, testing and acceptance criteria on many seismic retrofit projects. Updates to the FHWA Manual or DFI Sample Specification that specifically address seismic retrofit cases would be useful tools to disseminate information and enhance the state of practice.Micropile Survey UnderwayAs one step in this process, I am distributing surveys to contractors and designers prior to DFI Super Pile ’09 (June 4-6, San Francisco) seeking recommendations for design and testing procedures applicable to seismically loaded micropiles. I am also requesting any existing references that could be promoted as a standard for these cases. Anyone interested in participating in this survey, should contact me at rjameson@malcolmdrilling.com. Seismic RetrofittingMicropiles are ideally suited to seismic retrofit applications. Their high-tensile and compressive capacity can sustain the large concentrated loads induced during seismic events. They can be installed within and around the access limitations of existing structures, and can be drilled through and grouted into the wide variety of soil and rock materials encountered in seismically active zones.Seismic retrofits have included micropiles since the early 1990s, and they are now widely specified in the Western U.S. In the San Francisco Bay Area alone, thousands of micropiles have been installed for seismic upgrades of highway and transit aerial structures, and retrofits of commercial, residential and public buildings. Micropile use is growing in both public and private sectors, with large-scale retrofit projects currently underway for both the Bay Area Rapid Transit (BART) system-wide upgrades and renovations at San Francisco Airport."

Jan 1, 2009

By A. David Miller, Chika Oya

"Field sampling and testing are part of the Quality Assurance/Quality Control (QA/QC) requirements for all Cement Deep Soil Mixing (CDSM) Projects. Field sampling and testing are also used for determining the performance and quality of soil mixing method(s) and are the primary basis for accepting or rejecting the soil mixing wall among all other QC testing. Two of the most commonly recognized and used sampling methods for CDSM walls are wet grab sampling and verification coring. Depending on the types of wall construction and project budget, one or both of these methods are normally used to help evaluate the in-situ matrix and quality of the mixed soils. Additional to ASTM strength and permeability testing from wet grab sampling and verification coring, more and more testing methods are being employed and accepted. However, these other testing methods tend to be unnecessary, lack consistency and repeatability, and are more subjective to manipulation and interpretation. In certain projects, there are also misconceptions involved with the results of wet grab sampling and verification coring, hence it is important to note how these wet grab sampling and verification coring work and represent the work in terms of quality of production.TYPES OF PROJECTSCDSM projects include (but not limited to) in-situ stabilization, liquefaction mitigation, excavation support, groundwater cutoff, and pollution containment. Although these projects use similar equipment on the jobsites, each project is treated differently in terms of catering to specification, uses of different mix designs, and emphasis on certain steps during production.Different types of projects with different specification changes the focus of quality, but soil types in jobsite also determine how to proceed with production. For example, a jobsite with predominate gravel layer must be treated differently as opposed to jobsite with clayey sand as the main soil type.WET GRAB SAMPLEWet grab sampling is one of the most used testing methods for QA/QC. The wet grab sample specimen is retrieved right after finishing the production of the desired element.Wet grab sampling equipment consist the use of 28 cubic inch (458.84 cubic cm) box attached directly to one of the auger stems. Hinges attached to the top and bottom of the box is fabricated to allow collection only during auger withdrawal. The collection box is strapped just above the mixing paddles on the auger stem and measured from the center auger head tip to confirm proper depth of collection. This box method has been used in Japan and U.S. for numerous projects."

Jan 1, 2017

By Bill Paparis

The thirty year old wharf structures at the Port Authority of New York & New Jersey?s Port Elizabeth Marine Terminal are being modernized for the next generation of Post-Panamax container ships, which require deeper water and larger container cranes. The terminal operator is upgrading the wharf in order to remain competitive, now and into the future. The upgrade coincides with the Army Corps of Engineers? $733 million project to deepen the main shipping channel in New York Harbor. This paper focuses on the structural modifications to accommodate berth deepening and to support the heavier loads of the new cranes. An overview is provided of the design and actual construction, including typical problems encountered when combining new and existing structures. The wharf improvements included: ? Installation of a steel king pile/sheet pile cutoff wall along the face of the wharf to permit increasing the depth from ?12.2 m + 0.61 m to ?15.2 m + 0.61 m ( ?40 ft + 2 ft to ?50 ft + 2 ft) ? Removal of the existing crane rail support beams and installation of new piles and beams to support the increased crane loads ? Replacement of the existing timber fender system with a new system capable of resisting the berthing energy of a 152,000 MT displacement vessel, and having dedicated sections for berthing barges ? Replacing the existing overhead, landside crane electric feeder system with a waterside, cable reel trench system. The work included upgrading the transformer capacity at the terminal for increased crane power demands This paper provides a case history for port administrators, terminal operators, engineers, and shipping lines challenged with upgrading aging terminals.

Jan 1, 2013

By Derrick Dasenbrock, Mary C. Nodine, Benjamin Rivers

Up to 50 percent of major infrastructure projects suffer impacts to schedule or cost due to geotechnical issues, many of which correspond to risks related directly or indirectly to the scope and quality of site characterization work. The Federal Highway Administration (FHWA) in coordination with industry organizations seeks to address this issue through Every Day Counts (EDC), a program that identifies and deploys proven, yet underutilized innovations at the project level to save time, money and resources. The A-GaME (Advanced Geotechnical Methods in Exploration) is one of the innovations supported under EDC.

By Karen Dawson

Pressure-grouted helical piles support a new seven-story homeless housing center in the Coney Island neighborhood of Brooklyn, New York. The project team instrumented and statically load tested piles to as much as 1,000 kips (4.4 MN) in advance of construction to obtain the approval of the New York City Building Code officials and to verify the design. Use of pressure-grouted helical piles required additional design effort and time risk because of New York City's Construction Code Determination (CCD1) process, which is required for non- standard deep foundation types. Despite

May 1, 2022

By Peter J. Jancich

This paper describes the installation of high capacity Augered Pressure Grouted piles which support structural loading from a four level parking garage in west-central DuPage County, Illinois. The subject site is characterized by a variable glacial geology which presented, to the designer, a number of problems with respect to analysis and prediction of pile capacities, and, to the contractor, the very real difficulties associated with estimating the costs of, and installing foundation units in highly variable subsurface conditions. 2. General Site and Subsurface Conditions 2.1 Site Conditions - The subject site is part of an overall 300 acre property. Topographically, the overall site is saddle shaped with higher elevations along north and south boundaries and a subdued, east-west trending swale centrally located. Elevation relief is on the order of 25-30 feet (7.6-9.2m).

Jan 1, 1991

By Dinesh R. Katti

Caissons which are locally known as well foundations, which may very in diameter from 30 m to more than 30 m and in majority of the cases having depth to diameter ratio between 1 to 1.5, are normally used to support piers of long span bridges or tall structures, which transmit high magnitude of axial load, horizontal thrust and moment. On the basis of depth to diameter ratio the foundation system appears to fall in the category of shallow foundations but due to deep excavation, it is observed that part of the moment acting on the caisson is shared by due the sides due to development of passive resistance. The problem is statically indeterminate and three dimensional in nature. To ascertain the various parameters needed for design, such as moment shared by base and sides, horizontal and vertical displacement and tilt, and base and side contact pressure diagrams need to be obtained from nondimensional relations of parameters with respect to D/B ratio derived from large scale model studies conducted by Katti etal at IIT, Bombay under MOT Project between 1976 and 1988 and later on at UNEECS. On the basis of above data on attempt is made to put forward guide lines for selection of parameters for design of caisson foundations / well for following cases for opening us some discussion. The cases are cohesive soil at the side and cohesive soil, or sand or soft rock or hard rock at the base.

Jan 1, 1996

By Rich A. Lamb, Paul J. Axtell, Michael K. Muchard

"Since 2010, the Minnesota Department of Transportation (MnDOT) has performed eight full-scale compressive load tests on large-diameter pipe piles at four different project locations across the state. All of the piles were 42-in diameter, open-ended pipes driven to practical refusal on sedimentary bedrock with D125-32 diesel hammers from three separate manufacturers. The rapid load test method in general accordance with ASTM D7383-10 (Statnamic method) was used along with high-strain dynamic testing and subsequent signal matching. Results of these tests indicate that the axial nominal resistance of these piles in compression is not controlled by geotechnical considerations when driven with an appropriately sized hammer and installation criterion. Rather, the predominantly elastic load-deflection behavior of the piles under compressive load suggests the axial nominal compressive resistance is controlled by the structural capacity of the pile. In all instances, the rapid load tests indicated a nominal resistance exceeding that produced by high-strain dynamic tests due to insufficient hammer energy to fully mobilize resistance. In all cases, the hammers used were able to easily install the piles through the soil overburden. Mobilizing a larger hammer simply to demonstrate high-strain dynamic resistance is not economical or practical. This paper presents the subsurface conditions at each location, the ensuing test results, and the ramifications for future projects in Minnesota utilizing large-diameter open-ended pipe piles.INTRODUCTIONThe Minnesota Department of Transportation (MnDOT) has recently performed eight full-scale compressive load tests on large-diameter pipe piles at four different project locations across the state. The four project locations described in this paper where pile load testing was performed are shown in Figure 1 and exist in the southeastern portion of Minnesota. The projects are all major bridges crossing the Mississippi River in three instances and the St. Croix River just above the Mississippi River in the other instance. The first project is the TH 61 Mississippi River crossing in Hasting, MN where two load tests were conducted. The second is the TH 36 St. Croix River crossing in Stillwater, MN where two load tests were performed. The third project is the I-90 Mississippi River crossing in Dresbach, MN where three load tests were conducted. The final project is the TH 43 Mississippi River crossing in Winona, MN where one load test was performed."

Jan 1, 2017

By Alan J. Lutenegger

A series of tension tests were performed on prototype scale steel pipe piles at two sites to evaluate the influence of scale and pile plugging on the unit skin friction developed in axial tension. The first site consisted of a clean medium dense fine sand above the water table. The second site consisted of a loose silty sand with the water table within about 0.5 m of the ground surface. Pile load tests performed at each of the sites included piles with diameters ranging from 73 mm to 114.3 mm, which may be considered driven "micropiles". At the first site, pile lengths of 6.1 m were used; at the second site, pile lengths of 9.1 m were used. Some of the piles were driven open-ended while others were fitted with a conical tip to form a closed end. During installation, pile plugging measurements were taken on the open-ended piles after each 0.30 m of penetration. The piles were allowed to rest for a period of about 30 days after driving prior to performing the axial uplift load tests to failure. The results indicate that in the medium dense fine sand the unit skin friction developed in tension is dependent on both the amount of plugging that occurs and on the size of the pile, which was not the case for the loose silty sand.

Jan 1, 2000

By Samer Rabab’ah, John C. Niedzielski, Jason Valeria

The PHX Sky Train is an automated people mover system located at Phoenix Sky Harbor International Airport. Phase II of the PHX Sky Train includes the design of over 150 drilled shafts for support of four guideway abutments, 75 guideway piers and three proposed stations. The soil conditions in this area generally consist of alluvial Sand, Gravel and Cobbles (locally known as SGC) deposited by the nearby Salt River. The foundation system will support relatively high axial loads, lateral loads and moments due to the height of the elevated guideway above the ground surface, where it needs to pass over roadways, parking lots, an existing terminal, and other buildings. Deep foundation design involves designing drilled shafts within the SGC deposits, some of which extend below the long-term groundwater table. Such extreme design loading conditions, together with difficult ground conditions at the site, result in several challenges for the design and construction of the deep foundation system for the project. This paper will present the results of a drilled shaft load test program implemented to provide site-specific measurement of the axial and lateral performance of the project drilled shafts. The load testing program consisted of a bi-directional load cell axial load test and a lateral load test performed on an instrumented test shaft 84 inches in diameter. The development and execution of the load test program and analysis of the test results are discussed. Comparisons were developed between predicted load capacities of drilled shafts using different design methodologies and the load capacity measured from the load tests. The load test results showed that underestimation of the capacity is evident using conventional methodologies. The load testing program was important for verifying the performance of the drilled shaft foundations on the project and was used to reduce the size of the drilled shafts. INTRODUCTION The PHX Sky Train is a five-mile long automated people mover system situated at-grade and on an elevated guideway which connects terminals, parking facilities, a rental car center and the Valley Metro Light Rail system in Phoenix. The purpose of this automated train system is to provide a secondary transportation system within the airport to relieve roadway congestion, minimize wait times and travel times for passengers and provide climate-controlled waiting areas. Phase 1 opened to the public on April 8, 2013. Phase 1A opened on December 8, 2014.

Jan 1, 2019

By Gianni O. Chieruzzi

A 400 MW, gas-fed power plant on floating piles and piled raft foundations was constructed in the Province of Moskovskaya, Russia in 2008. The subsurface is characterized by fill underlain by loose to medium dense alluvial deposits, with peat and clay interbeds, a stiff to hard, highly plastic, silty clay stratum of glacial origin, and a stratum of very dense, varved interbeds of sand and silt. More than 800, drilled concrete piles were constructed at the site. The pile length ranged from 15 to 23 meters below existing surface grade, and the pile diameter ranged from 0.9 to 1 meter. Initial analyses by others predicted total power plant settlements of 3 to 4 cm when subjected to the permanent loading conditions. Under a peer review process for the equipment supplier, subsurface investigation and testing were performed to verify the consolidation parameters used for foundation design of the power plant foundation. The parameters obtained in this investigation were used in the 3-D finite-element model ELPLA as inputs for the settlement analysis of the turbine building and power island. The ELPA analyses predicted settlements on the order of 7 cm over a period of 30 years. The actual settlements after two years of monitoring were compared against the model predictions. The rate of settlement and the recompression index were both underestimated in our model. The measured settlements have enabled us to calibrate both of these model parameters so that the model better matches the data.

By William Auyeung

Micro-piles are small-diameter, drilled and grouted reinforced piles used for both structural support and in situ earth reinforcement. They were conceived in Italy in 1952, but have become popular in Canada and the United State only since the mid-1980s. The Province of British Columbia completed a construction of a 265-km (165 miles) four-lane highway between Campbell River and Victoria in the year of 2000. The construction of Big Qualicum Bridge was part of the above mentioned provincial government project and this bridge was made of twin cast-in-place concrete parabolic arch structures. The overall length of the bridge is 261 metres (856 feet) and the width is 24.2 metres (80 feet). The massive thrust from each arch is resisted by groups of 46 drilled micro-piles that are about 230 mm (9 inches) in diameter with No. 18 high strength Dywidag threaded bars with double corrosion protection up to 15 metres (50 feet) long. This paper will describe the micro-pile design and installation methods. The performance of the micro-piles in full scale testing in tension and compression monitored with electronic strain gauges will be presented. The impact of drilling methods on the performance of the micro-piles will also be discussed.

Jan 1, 2004