Search Documents

By R. H. Batey

"The process control and cost of monitoring mining slurries is normally accomplished using a continuous mass flow system, conventionally embodying a volumetric magnetic flow meter and nuclear density meter. DuPont’s Maxville Mine at Starke, Florida, USA was chosen to examine costs associated with performance of a nuclear density meter. Since it is typical of many mid-sized establishments and has a long history in their use. The published accuracy under ideal conditions of a nuclear density meter is ± 1.0%, but in practice considerable ambiguity of cost in annual production implies ± 2% at best. Using such accuracy in a 400mm (16”) pipe carrying zircon slurry at 75,000 tons/day, the cost of ambiguity, together with initial and running costs, amount to nominally $962,000 per year.Such cost leaves much to be desired. This paper describes an unique continuous, direct mass per unit volume Density Meter used for mining slurries in pipe sizes up to 1000mm (40”), which significantly reduces the cost of ambiguity of measurement and running costs. At the same time the disadvantages of nuclear devices are obviated.In an effort to reduce costs, a 400mm non-nuclear Density Meter was installed at the DuPont Maxville mine. A typical on-site accuracy can be shown to be ± 0.285%, whereby the cost of ambiguity, initial and running costs in the example above shows an annual improvement of $78,660, a reduction of over $880,000 per year.Even higher cost savings may be demonstrated with mass flow systems having gas entrainment compensation. Unlike nuclear and other inferential density meters, the signal quality of this non-nuclear Density Meter is totally unaffected by entrained gas found in mining slurries. This non-nuclear density meter is then ideally used with a vortex velocity domain sonic flow meter, and provides for the first time compensation in wet density or dry % solids, as well as wet or dry mass flow of mining slurries with entrained gas, resulting in enormous reductions in cost ambiguity."

Jan 1, 2013

By Chuck Edwards

"Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. Over that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin close out the paper.INTRODUCTIONThe roughly oval Athabasca Basin in northern Saskatchewan occupies nearly one third of the surface area of the Saskatchewan Shield. Its sandstone-like deposits lie unconformably on the older basement. The basin hosts many high-grade unconformity-type uranium deposits(Saskatchewan Energy and Resources, 2010) for which the Athabasca Basin is world famous. Uranium production in the Athabasca Basin has come from four mills. In the order of startup these are Rabbit Lake, Cluff Lake, Key Lake and McClean Lake. General data (AREVA, 2010; Cameco, 2010; Denison 2010) for each mill are shown in Table 1."

Jan 1, 2011

By Peter White

Mine Planning Shaft Collar Shaft Sinking Raises Ramp Underground Water Storage

May 1, 2009

By M. R. Dion, K. Frenette, R. K. Jonas, S. Simard, F. Robichaud

"In 2011, a site study indicated that the application of Honeywell’s Multivariable Predictive Control Technology (MPC) to the Goldex processing facility would provide significant opportunities for improvement. Grinding MPC was implemented in the SAG Mill in June 2015. This pilot application, called Phase 1, featured one of the first Multivariable Predictive Controllers to be installed in a Canadian mineral processing plant. Since the implementation of MPC, gold recovery from the gravity circuit has increased. MPC contributed to a decrease in flotation feed particle size (120 to 112 µm) and an increase in the SAG feed tonnage (8.5% increase). MPC also increased and stabilized the % solids of the SAG feed, which can have an impact on cost reduction (mechanical maintenance). Additionally, MPC increased productivity, providing grinding operators with more time to perform other tasks. Further anticipated benefits include the standardization of the grinding circuit operation from one team to the next, thereby minimizing circuit disturbances resulting from different operating philosophies. This paper will discuss the advanced control project development and justification, the technology and rapid implementation process, the performance results and the benefits obtained.IntroductionGoldex is an underground mine located near Val-d’Or that is owned and operated by Agnico Eagle Mines Limited (AEM). Between 2008 and 2011, mining focused on the Goldex Extension Zone (GEZ). In 2011, the project was halted due to geotechnical problems; operations ceased until late 2013. Goldex operations resumed in September 2013 with the M and E zones, for which there were 0.7M gold ounces of proven and probable reserves, 2.1M ounces of measured and indicated resources and 1.2M ounces of inferred resources, totalizing 4M ounces. Life expectancy was extended until 2024."

Jan 1, 2017

By M. Sharafodin, A. A. Hassanipak

Abstract - The essential aims of additional borehole drilling are to improve the reliability of grade and tonnage estimates in each reserve class and to increase ore tonnages. The "GET" function presented in this paper considers strategies for achieving both of these goals simultaneously, and therefore is advantageous for selecting sites for additional boreholes. The "GET" function is either a linear or a non-linear product of three variables G, E, and T: f(G,E,T,) = G??E??T??where the values of any or all of the exponents ?, ?, and ??may differ from unity at the discretion of the user. G and E are the average estimated block grade and the average estimation error for ore blocks in one vertical column, and T is the compounded ore thickness within the column. To illustrate its utility, the GET function has been used for determination of the most advantageous sites for additional drilling in the Shah-Kuh Pb-Zn deposit in west central Iran.

Jan 1, 2004

By K. Woo

The increasing move to block cave mining methods (including sublevel and panel caving) to access deeper and lower grade ore deposits as near surface sources become exhausted raises questions as to the extent and magnitudes of caving-induced subsidence as it may affect strain-sensitive infrastructure on surface. Predicting these surface deformations is difficult as they tend to be discontinuous and asymmetric due to large movements around the cave controlled by geologic structures, rock mass heterogeneity and topographic effects. Of further impediment is the sparse number of case histories available, in which actual subsidence measurements are reported to provide guidance and empirical constraints for subsidence calculations. This study reports the development of an exhaustive and comprehensive database of available (i.e. public domain) subsidence data from block cave mining operations from around the world.

May 1, 2009

"Each and every flotation plant must produce daily/weekly/monthly production reports in which metal balances for payable and penalising elements are presented. Several factors including ore heterogeneity and harsh production environment affect the reproducibility of the reported data. Best practices of metal accounting thus prescribe that production reports be accompanied by measurement quality reports quantifying the reproducibility (a data quality metric often expressed as a relative standard deviation) of each data reported. Ignoring the irreproducibility of measurements may lead to the perception that random errors have been totally eliminated through statistical data reconciliation, which is wrong. This paper aims at explaining the full lifecycle management of reproducibility estimation from the outset at the measurement process to its reporting after having been through the statistical data reconciliation process. Indeed, the reproducibility of reported data can be obtained by performing a sensitivity analysis. Necessary conditions for obtaining a truly representative assessment of measurement reproducibility are stated. Typical levels of measurement reproducibility found in operating flotation plants are also reported. These numbers can be used as benchmarks for reproducibility levels that can be realistically expected.IntroductionEach and every flotation plant must produce daily/weekly/monthly production reports in which metal balances for payable and penalising elements are presented. Such production reports are the most expected output from a metal accounting system (MAS). The duly recurrence of this task combined with an insufficient level of automation has somehow contributed to the misleading perception that it is mainly a clerical work. However, as shown in Figure 1, a MAS encompasses way more than just a reporting system. Acknowledging that the content of production reports indubitably origin from raw measurements has important implications for how both the reports and MAS should be monitored."

Jan 1, 2016

By D. J. R. Ras

A sub-level open stoping method is being used to mine the massive deposits at TARGET Gold Mine which uses cemented tailings to backfill the stopes. This requires the construction of bulkheads to contain the freshly placed backfill, capable of resisting the hydraulic pressure imposed by filling. The bulkheads must contain an 8 metre head of backfill slurry within 48 hours and withstand the force exerted by a 35 metre load of consolidated fill at a maximum estimated fill relative density of 1.9. After a variety of methods of construction were evaluated, it was decided to construct the bulkheads using the low density, fast-setting foamed cement-based product TEKSEAL HS manufactured by MINOVA RSA. The cement foam is contained between low-cost steel and fabric brattices which are easy to construct, using a method specially developed for the TARGET bulkheads. The paper will describe the design, trialling and construction of the bulkheads, and results obtained to date.

May 1, 2007

By Marc Ruest

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC?s Granger Mine, Meikle Mine, and Getchell Mine. A ?split-pipe? laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

May 1, 2002

By T. Bhambhani, D. R. Nagaraj

"Ultramafic Ni ores present significant challenges in processing in that both recoveries and grades are not satisfactory, due to the presence of Mg silicates in large amounts. Significant quantities of xanthates and CMCs are generally used for their recovery by flotation. Additionally, given that some of these ores are processed under acidic conditions, CS2 generation due to xanthate decomposition presents some safety hazards. Technology to replace xanthate has been developed for which the safety and health issues are absent. Collector S-10294 shows significant improvements in Ni and overall S recovery at a dosing rate of one half that of xanthate. New polymeric modifiers have also been developed that help reduce the Mg content of the concentrates at very low dosages. The reagents are custom designed for use in normal or hypersaline water, and acid or alkaline conditions.INTRODUCTION The use of xanthates in sulfide mineral flotation is reported to have started as early as 1925 (Nagaraj 2005). The reagent is now ubiquitous in the mining industry, accounting for 40-50% of total collector consumption. In recent years, the development of more selective reagents has rendered xanthates largely obsolete in Cu flotation. However, xanthates continue to be sold in large amounts in the Au, PGM and Ni flotation industry, where bulk sulfide flotation is required. The low cost and easy availability is the largest driver for the use of xanthates in the minerals industry. Of particular interest to this study is the use of xanthates in the flotation of Ni sulfide ores. About 60% of the world’s annual nickel output is obtained from sulfide Ni ores (Hoatson, 2006). A strategically important category of these ores is the ultramafic hosted sulfides, such as those of Western Australia and Canada. These ores are characterized by low Ni grades (<1%), with the Ni minerals being pentlandite, violarite, millerite and mackinawite, and gangue minerals comprising an array of altered Mg silicates, mostly serpentines. The challenges associated with treating these ores are well documented (Eltham et al. 1973; Claridge et al. 1975). One challenge is that Ni recoveries from these ores are lower. This has been attributed to the increased pulp viscosity, as discussed in detail by Vasudevan et al., 2010. Additionally, Mg silicates tend to report to the concentrate in large quantities, which is problematic for two reasons: a) concentrate dilution, and b) the high melting point of Mg silicates tends accelerate wear on the refractory lining of smelters. This has been attributed to network transport to the froth phase via bubble flux and entrainment (Patra et al, 2010)."

Jan 1, 2012

By Jan E. Nesset, James A. Finch, Frank Rosenblum, Rebecca Payant

"Under certain conditions of moisture and oxygen, sulphides can spontaneously heat, a phenomenon known as self-heating. In this paper, we test a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by restpotential difference between minerals and their surface area of contact (particle size). In order to decrease rest-potential, four sulphides were tested: pyrite, chalcopyrite, sphalerite and galena. Two series of samples consisting of mixtures of two sulphides, each representing a mass fraction of 50 %, were run in standard self-heating tests. The first series comprised five mixtures, two with low rest-potential difference (pyrite-chalcopyrite and chalcopyrite-sphalerite) and three with high rest-potential difference (pyrite-galena, chalcopyrite-galena and pyrite-sphalerite). The second series was performed on a pyrite-sphalerite mixture at four particle sizes (80 % passing 850 µm, 300 µm, 75 µm and 38 µm). The first series showed that the individual sulphides and the mixtures of low rest-potential difference did not self-heat but the mixtures of high rest-potential difference did self-heat. The second series showed that self-heating increased inversely with particle size (increased specific surface area) and revealed that it was the fineness of the pyrite (high rest-potential sulphide) that governed the self-heating effect, indicating the rate-limiting step is the reduction reaction on pyrite (cathodic mineral). The increase in self-heating with high rest-potential difference and increasing particle fineness supports the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on the hydrogen sulphide hypothesis is proposed where the reduction reaction at the cathodic mineral surface is ferric to ferrous. The understanding gained will be of interest to those involved in storage, shipping and disposal of sulphide minerals.INTRODUCTIONSulphide mineral ores are the major source of most base metals such as copper, zinc, nickel and lead. Once the ore is extracted, the sulphide minerals are liberated by size reduction (crushing and grinding), concentrated by flotation, and the concentrates sent for further processing to extract the metal (smelting and refining). At the various stages from mining to concentrate shipment and tailings storage, the sulphides are exposed to a variety of environments, which under certain conditions of air (oxygen), humidity and temperature can cause them to heat. Since no external heat source is involved, this pyrophoric process is known as spontaneous heating or, more commonly, self-heating. The self-heating of sulphides is associated with oxidation reactions under moist conditions. If the heat generated is greater than the heat dissipated, the sulphides will self-heat and the material temperature will rise. This can make working conditions potentially dangerous as oxygen is consumed from the surrounding air and significant quantities of sulphur dioxide (SO2) can be released (Ninteman, 1978)."

Jan 1, 2011

By Dale Dean, Bill Hancock, Raul Mondragon, Carlos Aguilar, Chris Martin

"In 1942, commercial mining operations began in what is now the Lucky Friday Ag/Pb/Zn mine in Idaho’s Silver Valley. Wholly owned since 1962 by Hecla Mining Company, the mine has produced more than 145 million ounces of silver and has been a mainstay producer in Idaho’s Silver Valley for over 70 years.However, by the early 21st century, the mill had fallen, technologically, seriously behind the rest of the industry. Accordingly, starting in 2005, the current mill management team set to revitalizing the milling operation. This paper will describe how the mill was systematically evaluated and the aging infrastructure replaced with more current technology. Driven by internal mill review studies supported by QEMSCAN mineralogical balancing, the mill has in recent years been through waves of upgrading – from the installation of new mechanical and column flotation equipment to the introduction of on-stream analysis, a technology well-accepted around most of the industry but alien to this technologically conservative mining district.The experience at Lucky Friday is a testament to the need for ongoing structured mill optimisation and technology upgrading in established mining operations. This paper will describe engineering experiences associated with upgrading equipment in an operating mill, contained in a confined building. Experiences in teaching the team new ways of operating a mill, and finally the metallurgical rewards that have been reaped will be described.INTRODUCTIONMining in Idaho’s Silver ValleyIdaho’s Silver Valley is a 64-km long valley flanked by the US Northern Rocky mountains, seldom more the 3-km wide, and stretching across much of Idaho’s northern panhandle, roughly 150 km south of the Canadian border. Mining has been continuously active in the area for more than 140 years, during which time, the Silver Valley has become one of the richest silver producing districts in the world, and as of 1985 had out-produced the 500 years of production from the famed Potosi district in Bolivia. Since 1885, almost 100 deposits have been discovered and worked in the district (Chapman, 2000)."

Jan 1, 2011

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

By A. Taylor, J. Shelegey, H. Sullivan, J. Doucet

"Historically, performance at Vale’s Clarabelle Mill was measured by Mill throughput and Mill recovery. After the economic collapse in 2008, a series of reviews were performed to drive improvements in business efficiency. These identified that product quality (e.g., concentrate grade, variability in concentrate grade) had a profound impact on downstream processes and suggested that improved control of these parameters would generate the greatest value for the customer (the Copper Cliff Smelter) and the company (Vale). Consequently, a movement was initiated to transform the Mill operating philosophy to consider customer needs as paramount. Systems and strategies used to drive the transformation are described. In 2011, an unexpected furnace failure resulted in decreased capacity at the Copper Cliff Smelter. In response, a two-stage change in production strategy was developed at Clarabelle. The first stage was to modify the ore blend feeding Clarabelle so that the concentrate grade could be significantly increased with minimal impact on recovery. The second stage was a circuit modification to ensure the elevated concentrate grade could be sustained. Execution of the first stage was complete five days after the failure and the second stage was complete within 10 weeks. Steps involved in each stage are outlined and the overall benefits are presented.INTRODUCTION Clarabelle Mill is located in Copper Cliff, Ontario, Canada (approximately 350 km north of Toronto). The Mill treats copper (Cu) and nickel (Ni) sulphide ores. The primary diluents are pyrrhotite (Po) and non sulphide gangue rock (Rk). The process description of the circuits at Clarabelle is documented in the paper by Taylor, Doucet, Blanchette, Barrette & Lawson (2012) in this Proceedings and will not be repeated. The Mill treats ore containing Cu, Ni and platinum group elements (PGE’s) and produces two concentrates; a Cu concentrate and a bulk Cu/ Ni Concentrate (referred to as nickel concentrate). The Cu concentrate is sold to market while the Ni concentrate is thickened at the Mill and pumped to Vale’s smelter complex in Copper Cliff Ontario for further processing. Since commissioning in 1971, Clarabelle Mill has undergone many circuit changes to suit the changing needs and wants of our customers, both internal and external. The Mill processes ores of varying quality, based on mineralogy and size and until 2009 the Mill daily performance was primarily based on throughput. The second key performance indicator (KPI) of “good” or “bad” performance was quality of the concentrate and third; Mill metal recoveries. There were other plant level KPIs such as flotation feed grind size, slurry densities and mass flows to the separation circuit, but for the most part each day was good or bad depending on how many tons were processed through the Mill."

Jan 1, 2012

By K. G. Thorne, M. J. McLeod, D. Hoy

"Throughout the Paleozoic, a variety of gold depositional environments were created in the New Brunswick segment of the northern Appalachians because of the complexity of arc and continental plate collisions and subsequent erosion of the orogen. In southwestern New Brunswick, recent exploration and research has focused on deposits and occurrences that can be broadly classified as intrusion-related, generated by late- to post-orogenic felsic to intermediate plutonic rocks emplaced during the Early to Middle Devonian. This work has led to the establishment of models for gold mineralization and guidelines for exploration in this area, which might also be applicable elsewhere in the southern part of the province and, perhaps, throughout the northern Appalachians. The deposits in the vicinity of Clarence Stream in southwestern New Brunswick exemplify this deposit type, and highlight the emergence of a possible major gold district in the region. Durant le Paléozoïque, une grande variété d’environnements aurifères ont été créés dans le segment néo-brunswickois des Appalaches du nord en raison de la complexité des collisions entre arcs et plaques continentales ainsi que durant l’érosion subséquente de l’orogène. Dans le sud-ouest du Nouveau Brunswick, les travaux d’exploration et de recherche récents se sont tournés vers les gisements et les indices appartenant à la classe des gîtes associés aux intrusions, générés par des roches plutoniques felsiques à intermédiaires tardi- à post-orogéniques mises en place au Dévonien précoce à moyen. Ces travaux ont permis d’établir des modèles de mise en place pour la minéralisation aurifère ainsi que des guides d’exploration pour ce secteur, lesquels pourraient aussi être appliqués ailleurs dans le sud de la province et, possiblement, dans l’ensemble des Appalaches du nord. Les gîtes aux environs de Clarence Stream dans le sud-ouest du Nouveau Brunswick sont un exemple de ce type de gisement, mettant en valeur ce qui pourrait devenir un district aurifère majeur dans la région."

Jan 1, 2008

By Paul Hosford, Tim Haldane

"The paper describes the fast-track development of the project from feasibility study through to detailed design and construction, highlighting the process adaptations for handling sticky ore and water management in a tropical environment, and subsequent commissioning and operating experience of the mine. The paper discusses the geological setting, the environmental and socioeconomic considerations in developing and operating a mining operation in an underdeveloped country and the logistical challenges involved in bringing a large capital investment into Central America.INTRODUCTIONGlamis Gold Ltd. acquired the San Martin project in Honduras as a result of its merger with Mar-West Resources in late 1998. Despite the prevailing low gold price environment at the time of acquisition, Glamis anticipated rapid development of the San Martin project due to the quality of the deposit and other positive factors.Following favorable exploration and permitting activities in the first half of 1999, Glamis prepared a Feasibility study. In October 1999, Glamis decided to proceed with the development of the project and selected Hatch to provide the engineering, procurement and construction management services for the project. The San Martin project was in full-scale commercial operation approximately 14 months after the receipt of Board approval, and by July 2001 the San Martin project was operating at approximately 150% of its feasibility design capacity."

Jan 1, 2002

By B. Y. Park

This paper develops a series of three-dimensional simulations for the Bayou Choctaw Strategic Petroleum Reserve. The U.S. Department of Energy plans to leach two new caverns and convert of one of the existing caverns within the Bayou Choctaw salt dome to expand its petroleum reserve storage capacity. An existing finite element mesh from previous analyses is modified by adding two caverns and increasing the size of existing Cavern 102. The structural integrity of the three expansion caverns and the interaction between all the caverns in the dome are investigated. The impacts of the expansion on underground creep closure, surface subsidence, infrastructure stability, and well integrity are quantified. The results show that from a structural viewpoint, the locations of the two newly proposed expansion caverns are acceptable, and all three expansion caverns can be safely constructed and operated.

May 1, 2009

By P. Radziszewski

"The comminution energy curve is a profoundly simple graphical technique that displays detailed operating efficiency information for industrial comminution processes. The database underlying the methodology has recently more than doubled, to now contain a substantial fraction of the international comminution output (1.7 billion tonnes of rock per year) across more than 8 major commodities. This increase has deepened the analytical capabilities and effectiveness for assessing comminution circuit performance in relation to comparable operating mines. This paper will explore how the energy curve methodology can be used to examine the ability of stirred mill technologies to increase efficiency.Specifically, this paper explores how the energy curves methodology can be used to present energy efficiency gains achieved at three mines employing a stirred mill technology under different duties. The first of these cases studies was conducted by Rosa (2014) who compared the performance of two ball mills operating in parallel with a Vertimill in the regrinding circuit at the Samarco Iron project in South East Brazil. The Vertimill was found to achieve the same product specification while consuming 40% less energy. Brissette (2010) investigated the impact of grinding media on the performance of both ball mills and Vertimills. The energy savings achieved varied from 10% to 40% for the ball mills and 30% to 60% for the Vertimills. Lastly, Bergerman (2012) investigated the operating conditions of the Sossego regrind circuit from 2006 to 2011 against design specifications and laboratory testing. The operating work index of this circuit varied from 5.2 kWh/t to 44 kWh/t over this 5 year period. The full suite of energy curves"

Jan 1, 2016

By L. Hanschar, C. Bwalya, E. Mokola, K. Musonda, A. Makayi

This paper describes the installation, commissioning and operation of porous plugs featuring nitrogen gas purging in both Anode Furnaces at the Kansanshi Copper Smelter (KCS), a greenfield copper smelter which commenced operation in March 2015. The decision to install porous plugs was taken in November 2016 and the facilities were successfully commissioned on both anode furnaces in October 2017. The project was successful and has demonstrated the following process improvements: 12.2% reduction in main burner fuel consumption Larger average charge size, due to fewer accretions; 17 minute decrease in average refining cycle times Improvements in slag skimming operations Improved casting rates INTRODUCTION Porous plugs The application of porous plug technology in copper smelter anode furnaces is well established around the world. Vukovic and Gamweger (2017) and Wallner (2004) noted that the stirring and mixing action induced by the injection of inert nitrogen gas into the molten copper via porous plugs has potential benefits in the following areas: Homogenization of the temperature and composition of the molten copper resulting in Reduced fuel consumption Less tendency to overheat slag (reduced risk of refractory attack) Less slag produced with a lower degree of oxidation (lower rate of refractory wear) Less tendency for buildups to form Improved environmental performance (produce low sulphur blister at Peirce Smith converters) Elimination of buildups inside the furnace and potential for larger charges per cycle Reduced processing times and potential for shorter cycle times More efficient skimming of anode slag Shorter skimming time Less copper carry over to Peirce Smith converters Very little slag remaining in the furnace (reduced potential for buildups to form)

Jan 1, 2019

By Vu Van Dong

Resource estimation is the science of determining the amount and quality of a given material in the ground that has the potential to be mined at a profit. This is because during this time computers have become more widely available and more powerful and software packages have become more comprehensive and user friendly. Over the past three years The Mining Geology Company with the support from Vinacomin Group has developed the Coal Geological Modelling and Reserve Estimation ? VMG system. The VMG system enables the geological and mining engineer to start at the reserve estimation for the mine design and planning. The VMG system enables the national and international standards (NI43-101, CIM-Canada; SAMREC Code, Africa, and JORC Code, Australia) and user friendly with menu driven thereby permitting the engineer with minimal computer training to rapidly learn and utilize the system. Geological and mining data input through digitized map files and drill-holes information files stored in the database that is an integral part of the VMG system with the main function for collection, validation, and recording, storing and processing of data will include both ?primary? (observation and measurement) and ?interpreted? data. It is recommend that data be stored digitally, using a documented, standard format and a reliable storage medium that allows for easy and complete retrieval of the data. The coal reserve estimation through standard polygon methods with the increased use of these mathematical techniques (geometrical modelling, geostatistical method, least square method, ?) over the last ten years corresponds, to some degree, to a decrease in both the amount of the coal deposit mapping and, in particular, coal seam structural interpretation and modelling, and permit rapidly evaluation of coal seam and overburden quality and quantity. The understanding of the relationship between the coal mineralization of interest and the likely related complicate geological processes and structure that govern its emplacement and geometry within the geological framework is essential to the establishment of the geological controls for coal mineralization. System outputs includes: drillholes summary reports, stratigraphy, cross-sections, isopach maps, structure, contour maps, premining and post mining topography maps, and 3D perspective view on coal seam structure.

Oct 1, 2009