Search Documents

By Brockway DJ, Holmes RJ

A natural gamma-ray gauge has been devel- oped for discriminating overburden and inter- seam sediment from low ash coal located on a moving conveyor belt. It is based on the difference in natural radioactivity of the sediment and overburden compared with the low ash coal, which is detected with a highly ef- ficient "Polyscin" NaI(T1) gamma-ray detector located underneath the conveyor. Gauges have been successfully installed on the bucket wheel boom of the two coal dredgers at the Loy Yang Open Cut. They are used to warn dredger operators that they are digging overburden or sediment and that action is required to avoid the sediment or divert it to the waste dump rather than send it to the coal bunkers at the power station.

Jan 1, 1987

Conflicting claims and views on the priming of ammonium nitrate/fuel oil (ANFO) are reviewed; certain fallacies and misconceptions are rectified. Optimum priming systems for a range of blasthole conditions are indicated. Moves towards optimum priming lead to reductions in the combined cost of drilling, blasting and handling the material. With shallow blastholes, two-point priming is rarely warranted. Best blasting results from single priming are usually obtained when the primer is located near, but not at, the bottom of the blasthole. As blast- hole depth increases, two-point priming becomes more reliable and effective than single priming. For two-point priming, primers should be located such that detonation waves in the ANFO collide at grade level or, if preferred, within a hard band in the burden. Where blastholes are very deep and/or strata variations can be appreciable, three or more spaced primers are often justified. The effectiveness of a primer varies with its detonation pressure, diameter and length. Primer properties influence the velocity of detonation (VOD) near the primer, but do not affect the final (steady-state) VOD in the ANFO. Some primers cause 'run-up' (i.e. lower than steady-state) velocities whereas others cause

Jan 1, 1974

By Richards AB

This paper describes the ENVIB software system, which has been developed in a menu-driven form to aid in the monitoring and assess- ment of vibration caused by routine blasting operations and for research and development projects. The paper gives an outline of the capabilities of the system by means of screen-dumps and a general descriptive commentary. Technical notes have been added where appropriate to further describe the system. The ENVIB system covers: I . Analysis of blast vibration results, and preparation of graphs and tables for control and estimation purposes. 2. Effects of atmospheric conditions and air vibration propagation. 3. Real-time acquisition and analysis of analogue blast vibration sig- nals directly from transducer equipment or from FM tapes. 4. Analysis of digital files on floppy disc or transferred via the serial port from blast monitoring equipment. 5. Transfer function calculation for structure response studies.

Jan 1, 1988

By J P. van Dijk, M Munro

Discrete vein modelling presents an innovative geology driven 3D modelling method for quantification of vein hosted mineral deposits, with far reaching potential for critical mineral supply and low impact resource extraction. By integrating key geological drivers with advanced discrete fracture network modelling, the DMX protocol (launched in 2019) converges to a more realistic representation of complex vein systems in three-dimensional space. The approach insights greater geologic reasoning in distributing mineral grades where vein boundaries are already defined. This presents a viable alternative to existing modelling and estimation methods and has important implications for mineral resource estimation and reporting. Further implications are discussed, where the enhanced understanding of complex orebody characteristics can potentially be used in optimising mining and mineral processing, supporting more sustainable and efficient mining practices.

Sep 1, 2024

By Hewitt D

A study of two laterite profiles developed on a serpentinite near Rockhampton, shows that loss of Si02 and MgO results in the relative concentration of Fe203, A1203 and a number of minor elements. Serpentine is broken down to form montmorillonite, goethite, quartz and kaolinite. Enrichment of nickel occurs, and it is shown that the element is mainly associated with montmorillonite and serpentine. Highest nickel values are associated with a zone in the profile which occurs at a depth of 10.5-22 metres, and the bulk of the nickel in this zone (42-80%) is associated with the

Jan 1, 1974

By R Steven

"Surveying, and as a result, surveyors, have been around since the start of time, and it has been said that so has their methodology!The theodolite and tape have been the backbone of a time-tested practice that has led to ground breaking advancements such as electronic distance measurement (EDM), global positioning system (GPS) and positional laser scanning. However, it was the introduction of the unmanned aerial system (UAS) that has allowed mine sites such as St Ives to take the next step towards truly turning survey data into metadata.This paper will explain how the unmanned aerial vehicle (UAV) was adapted to meet the requirements of a mine site supporting a major open pit operation, and how the open pit mining team adjusted their planning and production processes to maximise use of the extra data and information available to them.The advantages of the system include point cloud surveys with corresponding large-scale up-to-date photography and computer generated high detail contouring of mined areas that are then incorporated into the mine plan. All the while, the use of the UAV must be tailored to each specific problem encountered and a solution then matched.Citation:Steven, R, 2016. Trials, Tribulations and Triumphs of Unmanned Aerial Vehicle Surveying at St Ives Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 170–184 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

Water retention, water loss and delay in tailings storage rehabilitation are major challenges for many Coal Mines. Work by Stewart, Backer and Busch in the early 1980s suggested that there were improvements to be made in tailings dewatering and density by the addition of flocculant. This prompted ACARP, in cooperation with Bulga Coal Management (Xstrata), to initiate a research project investigating the impact of flocculant addition on tailings deposition density, water retention and the tendency for tailings to form surface crusts suitable for subsequent rehabilitation. A polyacrylamide-based flocculant (200 - 250 g/tds) was injected into the tailings line immediately prior to disposal into the impoundment area. The flocculated slurry rapidly released clear water and created a beach due to the immediate increase in deposition density. The deposition density increased from 35 per cent w/w to 61 per cent w/w solids within 24 hours and continued to increase to 75 per cent, seven days after treatment. The water capture at the tailings storage facility improved by more than 90 per cent; water which would otherwise be lost from the circuit through retention and evaporation. The impoundment capacity had nearly tripled due to the improvement in initial deposition density from 420 kg/m3 up to 1163 kg/m3. Four weeks after disposal surface crusts were forming on the storage facility, suggesting that there would be less delay between cessation and tailings storage rehabilitation.

Jan 1, 2008

By J E. Everett

When ore is being selected from a regularised block model, a common procedure is to accept as ore any block whose iron content exceeds a cut-off value, and whose content in each contaminant analyte is below an appropriate cut-off value. This method defines a quadrant within the multidimensional analyte space, such that any block lying within the quadrant is accepted as ore and any block lying outside the quadrant is rejected as waste. The cut-off levels can be adjusted to maximise ore tonnage at a target grade (or analyte vector). When the method is applied to a project comprising multiple pits with systematically differing grades, it is found that ore tonnage at target grade is maximised if different cut-off quadrants are used for the different pits. This is apparently illogical, because it implies that an ore block from one pit may be accepted as ore, but an identical block from another pit is rejected as waste, even when ore from both pits is to be blended into the same product and there are no production cost differences between the pits. The paradox is an example of the ætheory of the second bestÆ: if there are multiple conditions for optimality and one condition is broken, then obeying the other conditions may not be the best policy. The problem lies with the quadrant cut-off method, which is shown to be inconsistent even for selecting ore from a single pit. A criterion that is inconsistent cannot be optimal. It is shown that a linear composite cut-off function provides maximum ore tonnage, and that a single composite cut-off criterion is consistent and optimal over multiple pits. Further, it is shown that a composite cut-off function not only maximises ore tonnage at a specified composition, but also can be used to select ore so as to maximise project value, if marginal costs and values are available.CITATION:Everett, J E, 2013. Selection of ore from multiple pits, in Proceedings Iron Ore 2013 , pp 185-192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By S W. Houlding

The Certificate in Mining Studies program at the University of British Columbia, Vancouver, Canada is a collaborative initiative between mining schools and industry to provide accessible, cost-effective, accredited continuing education and training, designed to address the future needs of the global mining community. Content is provided by industry specialists and delivered through an integration of online learning, short courses and interactive webcasts. Accreditation is provided by a network of mining schools. In 2011, the program will deliver close to 100 short courses and interactive webcasts and provide 24/7 access to more than 130 online courses in six mining streams, to participants from as far afield as Tanzania, Argentina and Mongolia. The program is proving adaptable to corporate and mine site engineer-in-training and graduate-development programs, as well as providing accessible professional development opportunities for individuals. It also provides opportunities for cross-training from other disciplines and integration with mining school curricula.

Nov 22, 2011

By M G. Wansbone, R Bhargava

The inferred ground conditions for the proposed mined cross passages at the northern end of the Waterview Connection tunnels consist of an overburden of alluvial and residual soils, with mixed face geology of highly weathered to unweathered extremely weak rock. This paper describes three-dimensional (3D) finite difference analyses undertaken to evaluate the stability of the cross passage headings and to validate the proposed sequence of excavation. The analyses undertaken incorporated the influence of the construction of the mainline tunnels and the breakout opening in the segmental lining for construction of cross passages.The stability analyses were carried out using FLAC3D™, version 4.0 (by Itasca Consulting Group) by progressive reduction of shear strength parameters to obtain a failure condition and estimate a factor of safety. For each step of strength reduction, corresponding increments of displacements of several points on heading faces were monitored. The stability obtained from numerical analyses was compared with analytical solutions. Interpretation of results of drained analyses indicated instability of the upper 2 m of heading face within the highly weathered rock mass. Additional analyses were undertaken by including grouted fibreglass dowels to reinforce the heading face. The results of the additional analyses showed significant reduction in displacements and yielding of ground around the face. The proposed temporary support comprised face reinforcement using grouted fibreglass dowels in conjunction with canopy tubes and perimeter support of steel fibre reinforced shotcrete. The stability of the construction sequence, which was related to the specific requirement of the proposed excavation equipment, was validated.CITATION:Wansbone, M G and Bhargava, R, 2014. Analysis of stability and design of face support for cross passages – Waterview Connection tunnels, Auckland, New?Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 339–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The implementation of a process information management system (PIMS) is to provide a single online, real-time information system. This system provides a unique and completely open view for everyone, based on the key business drivers. It is structured around the three key concepts: process, maintenance and stocks. It combines numerous applications and provides accessibility to common tools and reports, through a web-based user interface, for every one from the floor operator to the General Manager. This æunique and commonÆ view displays raw, online process information that provides a quick health check of the operation at a glance, highlighting areas that require further investigation. The system is based on a hierarchical system of views, from the overview of the whole plant flow sheet to the more detailed operational shop view. It provides a synthetic view between continuous and batch operations, enabling the tracking of each batch produced. The batch view displays the critical batch components, and a comparison with each component of an ideal batch. This enables detailed analysis of each batch to identify areas of improvement. The information system will consist of an online reconciliation of stocks and flow data. This enables focus on the recovery of each process unit on a regular basis. This paper discusses the design strategy for the Process Information Management System, to ensure a unique and open view on the key business drivers is achieved and implemented successfully.

Jan 1, 2005

By B Young

Variable bench heights, interaction with underground workings and a steeply dipping orebody are challenges faced daily by geologists at Xstrata Zinc’s Black Star Open Cut (BSOC) Zinc/Lead/Silver mine in Mount Isa, Queensland.BSOC has been in operation since late 2004 and was developed to extract the surface extents of the Zn/Pb/Ag mineralisation mined in the underground lead mine. To date many large scale stopes and extensive development drives have been intersected and successfully mined. The stratigraphically hosted orebodies strike in a north-north westerly direction, dipping ~75° west. Ore production from the pit is currently at 4.5 Mt/a.Historically, sampling was conducted using a multiple spear technique from blasthole cuttings. This method proved to be relatively reliable when blasting benches at a consistent height, but a requirement to vary bench heights to safely collapse and then mine through underground workings reduced sample representivity to unacceptable levels.The purchase and commissioning of a production rig which had been converted for reverse circulation (RC) has allowed for the flexibility of a small rig, with the capacity to easily drill 48 m holes while ensuring sample quality. Sample quality is not the only benefit of introducing RC grade control. By collecting grade control data well in advance, informed decisions can be made by planning, drill and blast and mining departments weeks beforehand, rather than hours before firing. Additionally, seeking operational value to offset higher drilling costs has proved positive with benefits including increased confidence in orebody wireframes, accurate tonnage and grade for proceeding five benches along with the ability to representatively test metallurgical response on a tight grid spacing.

Aug 22, 2011

By C Jacobsen, N Harries

Assessing and managing instability hazards is an essential activity when working with unstable natural slopes and excavated open pit mining slopes. Slope monitoring has become the standard technique for the management of geotechnical risks associated with mine slope instability hazards. In recent decades, a proliferation of new monitoring techniques such as terrestrial radar, satellite InSAR and LIDAR have become standard operational tools, complementing conventional survey-based monitoring solutions. A reliable monitoring system should identify and record incipient anomalous slope movement. Although the most obvious purpose of a monitoring system is safety related, slope deformation and performance monitoring also enhance the understanding of slope behaviour and assists in improving system design and implementation. For a monitoring system to be considered an effective early warning tool, it needs to operate in real-time and should be linked to the mine’s emergency communication systems. Terrestrial radar systems have been developed that can provide near real-time measurements, at a high level of precision and covering broad areas in all weather conditions. This has had a positive impact on the management of geotechnical risks in operational conditions. The technology adoption of RADAR in mine monitoring has significantly progressed in the last 20 years from technology enthusiasts, to visionaries, to pragmatists to conservative users. However, the increasing adoption of RADAR cannot reduce or remove other monitoring techniques that often have important benefits; even if these technologies cannot be used as a real-time operational tool. An increasing awareness on the importance of combining data from different monitoring techniques to develop a holistic picture of all possible geotechnical hazards is a current industry trend. This is proving to be an excellent foundation for managing hazards associated with slope instability in open pit mines, and is only expected to improve with time with the adoption of new technologies based on big data and Artificial Intelligence (AI).

Nov 29, 2022

By L M. Lobato, J C. S Seoane, F J. Baars

The Carajßs Province presents several volcano-sedimentary sequences that comprise the Itacai·nas Supergroup. The rocks represent bimodal volcanism, and clastic and chemical sedimentation in relatively unstable basins subject to recurrent structural events with subsidence and volcanism. The Grpo Parß Group represents one of these sequences with mafic volcanic rocks that enclose discontinuous jaspilite lenses, with development of large high-grade orebodies (Fe >65 per cent). This unit is named the Carajßs Formation and presents peculiar characteristics compared to other iron districts in the world, thereby departing from the classic Lake Superior or Algoma iron formation types. Owing to the dense vegetation, lack of outcrops and harsh landscape, the structural analysis of the district can only be accomplished by combination of regional field work, detailed structural work on the open pits, and remotely sensed image interpretation, in this case Landsat ETM7, JERS-1 images and the SRTM digital terrane model. The regional trend of the several sequences of the area is approximately N-S and the structure is dominated by a flattened flexural fold system with axes moderately dipping WNW, intersected by several strike-slip faults subparallel to their axial plane. The Serra dos Carajßs represents an s-shaped synform-antiform pair, herein named the Carajßs Fold. This regional structure is partially disrupted by the Carajßs Shear Zone that divides it in the northern (Serra Norte) and the southern (Serra Sul) Ranges and also probably prepared the terrane with the development of pathways for mineralising hydrothermal fluids forming large high-grade massive iron bodies. Syntectonic granitic bodies played an important role in the structural evolution of the area as well. They caused localised ductile flattening deformation and thermal contact metamorphism in surrounding terranes. The Estrela pluton, for instance, was responsible for the discontinuity of the regional trend between the Serras do Rabo and Leste. The Carajßs Province is regionally the upper crustal product of a very shallowly eroded dome-and-keel geometry of Neo-Archaean volcano- sedimentary units intruded by syntectonic calc-alkaline intrusives and overlying pre-existing infracrustal rocks. The lithostructural data suggest continental-margin back-arc basin development and closure in an oblique collision belt, with N-S shallow crustal shortening, parallel to the inferred pre-existing strike of the stratigraphy.

Jan 1, 2005

By T N. Little

This review paper presents an integrated and practical insight to blasting geology and its importance. This approach involves developing blasting objective up front and implementing geology specific blast designs. The author refers to this approach as ‘starting at both ends’. There are many human-imposed controls on blasting operations, such as: safety, security, legislative, company standards, heritage, and environmental constraints. Thus it is possible for some operators to lose sight of the controls imposed by nature. This paper demonstrates how site geology controls or influences many aspects of the rock breaking processes and how a focus on this aspect has potential to add considerable value to mining operations. It is obvious that mining companies concentrate their efforts on economic/ore geology (good rock geology). However it is the author’s experience that they also concentrate on engineering geology (bad rock geology) only when forced to do so by the ground conditions, but seem to run out of puff before they apply blasting geology (big rock geology). This paper contains five main sections. In the first section, the impact of geological controls on blasthole drilling is briefly discussed in terms of drill selection, penetration rates, bit wear, blasthole stability, blasthole deviation, and health precautions. In the second section the geological controls on aspects of geometric design are reviewed. These include: hazardous minerals, valuable minerals, selection of the blasting techniques, geological structures, blasting direction, and blasting geometry. Section three overlaps with the geometric design section and deals with aspects related to explosives. Topics addressed include selecting the explosive type based on geology, distribution of explosive charge in space and time, explosive performance, and the rock response to explosive loading. In the fourth section, examples are given of the operational complexity needed to implement a blast to cater for difficult bench geologies, environment constraints, past mining (voids) and need for a high degree of quality control. Section five demonstrates geological controls on blast results. Blasting results include the muck pile characteristics, downstream handling and processing, damage to the remaining rock, and blasting emissions.

Nov 8, 2011

By G I. Lumley

‘Every mine is a pilot’ is an attitude which encourages the mining paradox of optimistic mine plans and equipment under performance; propped up by an environment lacking accountability. The premise that ‘every mine is a pilot’, appears to underlie the development and operating approach to most mines. It is the hypothesis of this paper that many mining companies, development teams and their managers largely ignore what is done elsewhere. Anecdotally, most planners don’t know whether the selected rates are high or low (rates based on theoretical models tend to be high – certainly higher than what most companies can achieve). Mines then consistently operate the equipment at rates well below targets; often more than 20 per cent below. Further to this paradox, mine performance data demonstrates the average mine is currently operating their equipment at levels of output not much more than half the output of those in the top ten per cent. On the whole mines don’t know the potential of their equipment and therefore don’t put appropriate plans in place to do better. After all, when ‘every mine is a pilot’ there is little reason to look to one’s peers for an indication of potential. This paper will outline why every mine is not a pilot and how mines do value some knowledge, but not as much as they should. This paper proposes a two-pronged approach to address this issue in the area of equipment performance. This approach is to:1. engage in better forecasting of equipment rates and better subsequent performance through benchmarking against industry standards2. provide conditions for more accountability.These parameters are linked and proper implementation of them will address the losses which many shareholders and financiers have incurred when investing in companies with unrealistic mining plans.CITATION:Lumley, G I, 2016. Is every mine a pilot? In Proceedings International Mine Management Conference, pp 75-88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Abrahamsson S, Niklasson B

In a follow-up of 12 production blasts in a quarry at the Mrica project on Java, tightly spaced porous bands were found to govern fragmentation to the extent that the average fragment size k5o was nearly independent of the specific charge within the range 0.30-0.56 kghn3. This fording resulted in a reduction of the running costs for drilling and blasting by 20-40%. Our work has given considerable practical benefits and insights into the blasting process, even if the results were of no direct use to check out fragmentation predictions based on models, which was one of our main Goals.

Jan 1, 1990

By H S. Pescini

A material aim when feeding ore blends into a processing facility is to reduce the variability of the properties of the feed material and to maximise the output, or throughput. At the Mining Geology conference of 2019, we presented a paper on optimal blending of coking coal given geological variability. The paper introduced integer-programming techniques to both maximise value and minimise feed or product variability. We discussed an application where the geological uncertainty is characterised using a normal distribution and exact solutions are readily obtainable using second order conic constraints in the mathematical model. Geological uncertainty is not always normally distributed, many properties will be characterised as log normal or some other skewed distribution. For example, copper can be some form of lognormal and Fe in Iron ore has a left skewed distribution. In this paper, we discuss some distribution free techniques to optimise the blends of plant feed or output given a quantified geological uncertainty. We discuss the sample average approximation method and how to set-up and apply the method to an ore blending problem. Evaluating a case study demonstrates that the explicit use of non-normally distributed geological uncertainty can better optimise feed into an ore processing facility and potentially add significant value. The approach is equally applicable to all mining and processing operations that blend material into a processing facility or directly into a saleable product.

Mar 22, 2022

By Corrans I. J, Yan D. S

The CIP process for gold recovery has enjoyed widespread application in most gold-producing countries. The development of a mathematical model of the CIP process has value for use in process design, process optimisation, and process control. Mathematical model development through laboratory experimentation is an important step in the design and optimisation of the CIP process. For this purpose, data has been generated through small scale laboratory leaching and adsorption tests both in batch and continuous mode. This test program has been carried out on specific ores of various types prior to the application of the models to production CIP plants utilising these ores. The applicability of leaching models derived from batch experiments was tested in a continuous five stage CIP pilot plant. The models were then adapted to scale-up the batch to the small scale continuous operation.

Jan 1, 1991

By S Davidge, J Pile, R Schumann, E Kepe, W Stewart, M Ridd, B Rathi

Geographical constraints, including steep terrain and high rainfall, at the Ok Tedi copper-gold mine in PNG’s Western Province present Ok Tedi Mining Limited (OTML) with significant challenges in mine waste management. Waste management includes discharge of tailings into the local river system and storage of waste rock from the mine pit in waste rock dumps which erode into the river system. Copper bearing skarn mineralisation is associated with a massive sulfide (mainly pyrite) deposit. Consequently, waste rock and tailings can contain significant amounts of pyrite. Without appropriate management, these waste streams represent a risk of producing acid and metalliferous drainage (AMD) when discharged to the river system. Throughout the life of the project, OTML have developed evolving strategies to manage mine wastes and mitigate AMD.

Aug 2, 2023