Search Documents

By Large RR

Precious metals in the Rosebery north-end orebody occur predominantly in sphalerite- galena-pyrite ore and to a lesser extent in massive barite mineralisation. Gold may also occur in the upper parts of pyrite-chalcopyrite ore (although this ore type is usually gold poor), in pyritic mineralisation lateral to base metal sulphide lenses and in the footwall (very patchy). Although present, remobilised precious metals do not occur in economically significant quantities. Mineralogically, silver occurs dominantly in tetrahedrite and, to a lesser extent, argen- tiferous galena. Gold occurs as electrum associated dominantly with pyrite and, to a lesser extent, tetrahedrite. Geochemical modelling suggests that silver was probably transported as a chlorocomplex, while gold was transported dominantly as a thiocomplex, although at high temperature gold was transported as a chlorocomplex.

Jan 1, 1987

By Mitchell M. A

The steeply dipping Mammoth orebody is mined by Gunpowder Copper Limited using a sub- level uphole bench stoping method at a mining rate of 350 000 tonnes per year. of three per cent copper ore. Access to the mine, is provided by 1 in 9 decline which spirals in the footwall connect-, ing all the sublevels, thus maximising mobility and accessibility of trackless mining equipment Sublevels are driven in ore off cross- cuts from the decline every 15 metres vertic- ally. Sublevel drives are stripped out to widths up to 18 metres before cutoff slots are mined at each end. A two boom fan drilling jumbo is used to drill inclined rows of holes to the floor of the sublevel above. Two or three rows are fired at a time which allows broken ore and remnants from the level above to be mucked out by rubber tyred LHD equipment to the brow. Ore widths of up to 80 metres are en- countered at lower levels where ring drilling from longitudinal drill drives will break ore to a draw point system below. Development is carried out with three boom rubber tyred jumbos. All haulage from the mine is in 20 and 35 tonne rear dump trucks. All aspects of the mining operation are discussed including ventilation, pumping and drainage, services and future planning.

Jan 1, 1974

Woodlawn Mines began underground operations in 1986. At the time of going underground it was envisaged that there would be no 'contract' payment to the underground employees. This was a relatively unique step to make, especially as most major underground mines in Australia relied heavily on the contract system to motivate their workforce. (Obviously with varying degrees of success.) Woodlawn faced the task of motivating their employees through a multi-skilled system with a great emphasis on leadership and a genuine care for their employees. The 'proof of the pudding' is that Woodlawn has not lost any time over industrial issues since beginning underground operations in 1986. To achieve success in any operation the organisation must not only be advanced in its management principles but also be prepared to be innovative in the way it deals with physical problems, ie ground control, equipment selection and maintenance. Difficult ground conditions at Woodlawn have necessitated the deployment of two Cabolt Jumbos and the construction of cost-effective shotcrete systems. The shotcrete system now being built has been tested in a prototype form and is proving to be a safe and simple way to manage weak, low stress friable ground. Although the ground at Woodlawn has low stress component by virtue of the fact the ore can have a density of 4.5dm3, cable dowelling has become a necessity. The two cable dowel jumbos install high quality reinforced cables. The pressure of 'production' means that these machines must be consistently available for use and the training of maintenance personnel and operators ensures that a maximum of cable dowels can be installed over any given time span. In any modem mine ventilation is a primary concern and the major area of concern comes from the vehicles themselves. In our recent replacement for the standard 'Toro' loader, three engine options were considered. A relative newcomer to underground mining was accepted. The Detroit 60 series (DDEC) engine came with a great reputation and has lived up to this. The engine has an electronic management system that reduces particulates to a hardly visible minimum, provides great amounts of engine power and reduces fuel consumption by approximately 45 per cent. The operational benefits of such an engine are worth sharing through this conference.

Jan 1, 1995

By Recepoglu O, Tolun R, Yavasoglu N, Bulutcu AN

Scheelite was floated from a low-grade (0.28 per cent W03) calcitic (96.30 per cent CaCO3) scheelite ore using oleoyl sarcosine as collector and alkylated 8-hydroxyquinoline as modifier. Compared to oleoyl sarcosine alone, the grade and the recovery of scheelite concentrate were increased from 8.07 per cent to 33.54 per cent and from 55.1 per cent to 73.4 per cent, respectively. Infrared studies with pure calcite and scheelite minerals showed that while alkyl oxine is adsorbed on the scheelite surface, it is not adsorbed on the calcite.

Jan 1, 1993

By Morrison RD, Peberdy NJ

Simulator training provides a cost effective method of training operators in both the process and control aspects of a metallurgical plant. The components and requirements of a training simulator are described along with the benefits to be gained from simulator training. A table summarizing some applications of metallurgical training simulators is Given.

Jan 1, 1991

IT will be noticed, from the following contributed papers on the various plant, what an infinite number of parts are required to be kept in active operation in order to derive a resultant product of commercial value from the ores and materials received at the works. Crude ores and concentrates, in every degree of complex structure and resistance to treatment, are arriving daily from near and distant places, moreover their metallic contents are so varied that an outsider, unacquainted with the operations, would naturally wonder how it is possible that the rare elements are to be sorted out and classified into their true order, to meet industrial requirements.The proposition is necessarily not a simple one and owners of mining properties have naturally refrained from smelting their complex ores on account of the technical difficulties of attaining high efficiency and recovery of the metals, where limitations are imposed in procuring a variation of ores that lead to the best smelting and refinmg result. This difficulty obviously imposes many disabilities on the smelter, who is prepared to accept all such complex ores, and it may be said that were therenot available a large weekly supply of lead concentrates from the company's own mine at Broken Hill, of standard quality, much of the material being treated in the world today would certainly not be marketable.In order to sustain full efficiency, each section of the works must maintain its.true balance and synchronize with the requirements of such other departments as are dependent on its partially treated materials. This harmony of operations is not only imperative as regards tonnage output, but also relies on the condition of the resultant treatment by each plant, no large variations being permissible.The various officers are, therefore, dependent on one another to keep the order of the operations flowing regularly. This is accomplished by constant intercommunication and observation, as...

Jan 1, 1918

The estimate of an ore reserve is a vital statement made about a mineral occurrence by an evaluator. It is important that such a statement communicate reality to all groups involved in a mining project, be they technical, financial, company directors, Stock Exchanges or the public. Ore reserve statements should state both resources and recoverable ore reserves. Resources may be important in very long term considerations, (because mining, metallurgical technology and economics change with time) but recoverable reserves are todays reality. The important factors contributing to recoverable reserves (in a general sense) are geology, mining method (and its impact on dilution and ore loss), metallurgical recovery, costs and commodity prices. These all need to be reflected in the ore reserve statement. In this paper recoverable ore reserve concepts across a wide range of orebodies are considered and discussed with respect to geology, mining method and ore reserve calculation procedures.

Jan 1, 1987

By Hammond J. R, Ward T. A

The Tom Price orebody, in the Hamersley Ranges of North West of Western Australia, is mined by Hamersley Iron Pty. Limited. The orebody is a folded sequence of hematite and shale bands capped with goethite, with a con- sequential variable iron content. The overall grade is below that required to yield spec- ification product, necessitating selective mining, 'Zone Plans' based on geological structure have been developed to yield forward information on material types and grades. Short and medium term mine plans - the initial stage of quality control - are based upon these 'zone plans'. Blasts are laid out to break to the grade boundaries, thus minimising dilution, and the samples taken from the blasthole cuttings provide blast grades. Blending of shovel out- put from different blasts forms the operational basis of grade control. Shales, being more friable than hematite, produce fines that are lower in iron grade than lump. Quality control in the mine centres around maintaining the target fines grade, compensation being applied in the mine if the fines grade lies outside the target range.

Jan 1, 1973

By J C. Small

Time-dependent deformation occurs when geo-materials are under an applied load; this may lead to additional deflection of a tunnel structure and the stress redistribution in the surrounding rock, shotcrete lining and rock bolt support system over time. A better understanding of this creep behaviour can improve the reliability of design, construction and maintenance of tunnels. Hence, the present investigation was carried out on the time-dependent properties of rock, shotcrete and the combined tunnel support system. Tunnels constructed in different ground conditions were modelled. The closure changes of the tunnel with time and the redistribution of stress in the surrounding rock, shotcrete lining and rock bolts due to the creep deformation were analysed. Results of the present analysis were compared with the results from the commercial program ABAQUS.

Jan 1, 2008

By Savory P. J

Uranium mining operations commenced at Ranger mine site, Jabiru NT Australia in May 1980. The Ranger orebodies, totalling approximately 110 000 tonnes contained U305 had been indicated by airborne radiometric survey in 1969 and confirmed by drilling the following year. Both diamond and percussion drilling methods were used to define the mineralisation and samples were analysed using a combination of radiometric and neutron activation techniques. Ore reserve estimates were calculated from conventional and geostatistical methods, and following the mining of 15 million tonnes of ore, reconciliations with before mining estimates are well within acceptable industry standards. In-pit grade control employs radiometric techniques including a radiometric truck discriminator built in Australia to mine specification to meet production requirements and improve productivity. Environmental requirements associated with uranium mining are a daily consideration.

Jan 1, 1993

By Hodkinson I, Teale GS

Mount Leyshon is an open cut-heap leaching operation that commenced production in early 1987. Open pit reserves are 6.3 m.t. grading 1.8 g/t Au and 4.8 g/t Ag and expected annual production is 68,000 oz. of gold. Gold mineralisation is hosted in breccias, porphyry plugs and basement rocks interpreted as the roots of a multi-phase Permian phreatomagmatic breccia complex. Mineralisation has the form of veins, cavity fillings and disseminations and is localised by late stage trachytic dikes and sills and dike-like bodies of milled breccia in the northwest corner of the complex. The sequence of mineralisation includes: I quartz-chalcopyrite-molybdenite stockwork veins and pyrite-gold veins with potassic alteration II quartz-chlorite-carbonate-basemetal sulphide-gold veins and cavity fillings with sericitic alteration III quartz-basemetal sulphide-bismuth-sulphide -electrum veins, veinlets and dissemin- ations with sericitic alteration. Mineralisation is interpreted to have formed at 500-300¦C from a predominantly magmatic hydrothermal system related to the porphyry intrusive bodies. Mount Leyshon is a phreatomagmatic breccia with a very different origin to the Kidston magmatic hydrothermal breccia. However the mineralisation style and origin is quite similar.

Jan 1, 1987

From the ventilation aspect, there is a basic difference between advancing and ezreating longwall layouts. Particular rroblems with retreating, using differing mining methods and layouts include high gas emissions, spontaneous combustion and -radients. There is an acceptable method of crntrolling the environment at the return end a retreating longwall face without the use a multiple heading system. Incorporated in the design is the facility to practice xtensive methane drainage, thus ensuring a ntrol of the rate of methane emission into the main roadways. Case studies highlight varying mining editions under which the proposed system of Ctised.

Jan 1, 1982

Willemite mineralization was discovered in 1966 in the North Flinders Ranges of South Australia, in the course of a stream sediment sampling programme. Further work outlined a total of nine separate willemite occurrences in the Copley/Beltana area, and ten small deposits in the Toondana area south of Parachilna. Mineable reserves of 1 000 000 tonnes grading 36.8% zinc were outlined in three deposits in the Copley/Beltana area and campaign mining of the Main Orebody commenced early in 1974. The main group of deposits all occurred within red, dolomitized Cambrian Ajax Limestone, and most are associated with significant thrust faulting. The area of the Main Orebody group of deposits has been intensely fractured, and the surrounding dolomites are often brecciated and contain up to 5% zinc. Lead and arsenic mineralization are minor components of the main group of deposits. Masses of Middle Proterozoic Willouran Formation crop out adjacent to or close to most of the deposits in the Copley/Beltana area. The Willouran is frequently highly sheared, brecciated, and often contains large inclusions of younger formations. It is believed that most of the Willouran outcrops represent piercement structures.

Jan 1, 1975

MERLIN, the Queensland Department of Minerals and Energy's corporate geographic information system, provides ready access to all georeferenced data held by the department. Its aim is to provide a consistent, current, statewide coverage of timely information to assist in tenures management, exploration targeting and competing land use decision-making. Initially developed in 1988 and under continual enhancement since then, its functionality is the result of on-going close consultation with a wide range of departmental clients and potential users. A true geographic information system, MERLIN maintains both graphical data with linked textual information on a wide range of features of interest. The proprietary software products Arclnfo and Oracle are used to hold the graphics and attribute information respectively. Access to information is provided by a specially designed graphical user interface programed in-house. Hardcopy output of graphics displays including related attribute data as well as detailed reports of textual information can be retrieved at any departmental office. MERLIN is a network of computer systems which link each of the Department's regional offices and head office in Brisbane. The current state of exploration and mining is maintained by departmental officers processing tenure applications, transactions and dealings directly into the system. Data entered at regional offices are transferred overnight to head office to up-date central records and maintain a currency of data statewide as at the close of business the previous day. Through MERLIN the Department of Minerals and Energy now offers a much streamlined tenures management service as well as access to information about past exploration and mining, Queensland's mineral and energy occurrences and resources, and up-to-date information on the state's geology including maps, boreholes, geophysical surveys and field observations. In the future, this Geographic Information system will be invaluable to the mining industry in the development of mining projects.

Jan 1, 1995

By Tien J. C

Many factors (type of coal mined, water pump pressure, wetting agent concentration, etc) will affect the performance of a dust suppression system using a water spray in an underground coal mine. While a two-level factorial method is useful in

Jan 1, 1994

General design of pillars to ensure a continuing roof support during ex- traction is discussed. Practical problems associated with pillar extraction are Outlined.

Jan 1, 1974

The paper highlights the conceptual developments in rock mechanics applied to quantify the effect of bolts in the stabilization of joints and yielding soft rocks. NOTATION Aa = stress change after excavation Eä EE, Eä = moduli of intact rock, single joint and jointed rock Eb = elastic modulus of the bolt k, = normal stiffness of joint Ab = cross section area of the bolt A, = area of influence per bolt ab = axial bolt stress e, = axial strain of the bolt eä e,, ej, = strains of intact rock, joint and jointed rock Ai = area of the joint ,r+ = shearing resistance of the bolt (at the joint) a = normal stress at the joint plane aäa3 = major and minor principal stresses c;, 4i; = cohesion and friction angle of the joint 0 = angle between the bolt and the joint a = inclination of the joint to the vertical axis P = bolt density parameter u, = convergence of unsupported tunnel section u, = convergence of bolted tunnel

Jan 1, 1992

By Spottiswood DJ, Kelly EG, Bull WR

An empirical model of a 254mm water-only cyclone treating minus 17001im coal has been developed. The model includes the prediction of by-passing, SG50 corrected, water split and the use of a single equation forthe reduced performance curve of particles in the range 1700-106pm. Particles finer than 106pm did not separate according to specific gravity. Simulations using the model showed the water-only cyclone performance to be dependent more upon feed size distribution than washability when the feed contains high-ash fines, but that, with a deslimed feed, the yield and ash content of the over-flow should be controllable by altering feed rate or feed pulp density.

Jan 1, 1985

Safety and health at work is about people. It is about people who plan for work, organise work and perform work. It is about those who come in contact with the workplace and those who are responsible for the workplace. There are wider ranging safety and health obligations that are imposed on the industry stakeholders that span all phases of the production process. In all cases, those responsible for discharging the obligations must ask the questions: Is what we propose safe?, can it be done safer? and are we sure? What we learn from recent legal cases before the courts is that it is essential that all stakeholders work together in a collaborative way when discharging these obligations. Safety and health at work cannot become an issue that is viewed only through the eyes of a single stakeholder group. The reason for this is quite simple. The interrelatedness of the responsibilities that are imposed on each of the stakeholder groups, means that the performance based legislation simply wont work, where an active model of communication and consultation is not in place.

Jan 1, 2005

Expert systems are a product of Artificial Intelligence (AI), a field of long standing, dedicated to the study of problem solving using heuristics, construction of symbolic representations of knowledge about the world, communications proce

Jan 1, 1998