Search Documents

An extensive series of tests was carried out on a ball mill-rake classifier circuit in the New Broken Hill Consolidated Ltd. concentrator. The data were used to develop a mathematical model of the operation of a rake classifier and this model has been used in the simulation of the performance of a ball mill-rake classifier circuit on a digital computer. As a result of this simulation it has been possible to develop a technique for the optimization and control of a circuit which includes these units.

Jan 1, 1967

By P Steinier

Most operations, when considering their comminution circuit, are primarily concerned with achieving the desired particle size distribution to obtain adequate liberation for the separation process, at minimum cost. Invariably, the effect the grinding media has on the subsequent separation process (ie flotation, leaching) is not taken into account when selecting the media. This choice is driven by cost rather than metallurgical outcomes. Maximising valuable mineral recovery, with optimum selectivity against gangue minerals, is about good particle preparation. And, particle preparation is strongly related to achieving adequate mineral liberation with the correct pulp chemical conditions. However, the pulp chemistry of a system is largely ignored and relies heavily on pH control and the addition of appropriate reagents (collectors, frothers, activators, depressants). The changes effected by the addition of the various reagents are obtained through conditioning the ground pulp prior to or during the concentration stage, subsequent to grinding. Frequently, reagents are added during grinding with good effect, but the impact of the grinding media on down stream processing is usually overlooked. A number of case studies examining the effect of grinding media on pulp chemistry and subsequent flotation performance were completed on several different sulfide mineral systems (for example, lead/zinc, copper, refractory gold). The evidence suggests that a change in grinding media type from forged to high chrome (ie conditioning the pulp during grinding) resulted in a shift in pulp Eh to less reducing conditions, an increase in the dissolved oxygen content of the pulp and a reduction in the iron species present. The changes have a positive impact on flotation behaviour. The results of the case studies are discussed.

Jan 1, 2004

This paper briefly describes the shaft, including sinking, steel sets and their installation, shaft equipment and winders.INTRODUCTIONThe New Broken Hill Consolidated Ltd. Service Shaft is a vertical concrete-lined circular shaft, 20 ft. in diameter with -steel sets spaced at 12-ft. centres. The diameter of 20 ft. was established as the minimum that would enable the shaft both to house the proposed hoisting and service equipment and to satisfy ventilation requirements as a downcast airway. The 12-ft. set spacing was based on South African practice in similar types of shafts.The shaft extends from the surface to 28 ft. below No. 22 Level, a total depth of 3,194 ft. Sinking was commenced in September 1946, and equipping completed in January 1955. Initially the shaft was sunk and concrete-lined to a depth of 52 ft., using a stiff-legged crane and clam-shell grab for mucking. Operations were suspended at this depth to allow the installation of the steel sinking head-frame, winders and ancillary equipment.Sinking and concreting were recommenced after four months and continued to a depth of 1,035 ft. 6 in., where the shaft connected with a pilot opening. The concrete lining was poured as sinking progressed and was piped from the surface to this depth, after which all concrete was lowered in buckets and discharged through a distributor suspended in the shaft. A cycle of stripping to the pilot opening and concreting was continued until the shaft reached No. 22 Level. From this level the remaining 28 ft. was sunk full size. All plats were cut and concreted as sinking progressed.

Jan 1, 1957

Radioisotope x-ray methods for the on-stream determination of copper, lead, and zinc in mineral product slurries were developed, and were successfully tested at the plant of Cobar Mines Pty. Ltd.The tests were made in three stages. Measurements to determine the precision of analysis were made initially on briquettes of the mineral products. The effect of slurry solids content variations was then determined by measurements on the mineral products in a recirculating slurry loop. The radioisotope analyser was finally tested in a series of on-stream measurements in the plant.Copper, lead, and zinc in flotation feed and in copper concentrate were determined to a precision ranging between 1·4 and 15 per cent of the mean element concentration in the slurry solids. These precisions are within limits required for plant control purposes at Cobar.

Jan 1, 1971

The Bayswater seam of the Singleton Coal Measures is discussed in relation to its field occurrence and related li~hotype profiles. The seam is correlated throughout widely separated areas of the Hunter Valley with the Farrells Creek seam at Howick, Broke seam at Broke, and Saddlers Creek seam at Mt. Arthur. The unusual features of composition of the seam in relation to adjacent seams is dealt with in terms of the seam environment, particular attention being given to the sandstone at the base of .the seam. Petrographic and other data are used to support the arguments submitted.

Jan 1, 1973

By Lynch A. J

A method has been developed for the prediction of the performance of multi-stage grinding-cyclone classification circuits of any degree of complexity on any ore for a wide range of operating conditions. The method involves the simulation of the circuit on a digital computer by means of. mathematical models of the individual units. At present, to establish the characteristics of the ore and the machines in mathematical terms, it is necessary to know the performance of a simple system on the ore for one known feed rate and feed sizing analysis.Further work on the separate identification of the terms defining the characteristics of the ore and the machines may permit the method to be applied directly to the data derived from small scale tests on ores.INTRODUCTIONThe cost of preparing metalliferous ores for concentration processes by, grinding and classification frequently represents a major portion of the cost of treating such ores, and it is necessary both from an economic and a metallurgical point of view that grinding and classification circuits should be operated at their optimum efficiency. It will be realized that the processes carried out in all units in such circuits behave according to physical laws and, if a mathematical representation of the laws applying to each unit could be derived, optimization of the overall process for any given conditions of feed or product may not be difficult.The physical processes in both tumbling mills and hydraulic classifiers are extremely complex and do not appear at present to be amenable to a rigorous mathematical analysis. However, empirical mathematical models of grinding units which have been presented previously (Callcottand Lynch, 1963; Lynch and Moore, 1963) may be used to discuss the operation of the grinding units in multi-stage circuits. Another type of model, which leads to a reasonable...

Jan 1, 1965

By G Chitombo, D Francis, P C. Stewart, I Brunton

The ability to precondition (weaken) a rock mass to enhance caving (cavability and fragmentation) is becoming increasingly important, as more potential caving deposits are in stronger rock masses, and at greater depth. This paper discusses a full-scale blast preconditioning experiment conducted at the Cadia East mining operation, including quantification of visible and microscale blast damage. From a cave mining perspective, the objectives of the experiment were to quantify the effect of confined blasting on rock mass characteristics relevant to enhanced caving, and to provide calibration data for the purpose of numerically modelling alternative blast preconditioning designs.The experiment was located approximately 360 m below surface, and consisted of two f165 mm blastholes (60 m vertical holes) and eight HQ diamond drill monitoring holes (35 m horizontal holes). The diamond drill holes were used to sample the rock mass before and after the blast at varying distances from the blastholes. Rock mass blast damage was quantified both visually using core logging, and on a microscale using LABYRINTH® statistical analysis of X-ray microtomography data. Results from the experiment indicated four major findings:on the visible scale, the experiment indicated a 147 per cent increase in the number of hairline cracks within 5 m (p value = 0.015), but no change in geotechnical logging parametersmicroscale tomography of intact rock samples indicate significant localised intact rock damage up to 4 m from the blasthole (p = 0.007)preliminary point load test results indicate that blast damage results in a significant reduction in intact rock strength (p = 0.050)the significant increase in porosity and microfracture size associated with damage provides a mechanism for reduced intact rock strength due to confined blasting.CITATION:Stewart, P C, Brunton, I, Francis, D and Chitombo, G, 2016. Quantification of rock mass damage associated with a confined blast preconditioning experiment at the Cadia East block cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Study on the New Flow Sheet and Wastewater Recycling for Xiaoliuguo Copper-Bearing Low-Grade Scheelite Ore

Sep 13, 2010

THE following brief paper is submitted with a view to encouraging the exploitation of hitherto neglected 10w~ grade ore-bodies which are suitable for extraction by open-cut methods.The Corinthian North mine, situated 10 miles from Southern Cross, in the Yilgarn district of Western Australia, furnishes an example of low working costs, although operations are carried out on quite a limited scale.The body of quartz which is now being worked strikes N.W. and S.E., has a very slight underlie to the west, and lies between bodies of quartz-hrematite s,chist on the east and amphibolite on the west.So far as the property has been explored, it would appear that the underlying sulphide rises to within about 70 ft. of the surface in the northern end of the workings, and pitches away to the south at a grade...

Jan 1, 1915

At last year's. annual meeting of The Institute, Sir George Fisher, as President, compared it somewhat nostalgically with a meeting of its kind in the 1920s when comment was expressed on the decline of Australianmining and on the lack of new mineral discoveries.I feel that tonight's annual meeting is even more an occasion for nostalgia, for it represents the seventy-fifth anniversary of the founding of The Australasian Institute of Mining and Metallurgy. I hope, therefore, that I may be allowed to retrace some of the circumstances of this Institute's origin and at the same time to look at some of the broader happenings of those 75 years.From this distance in time it is, of course, much easier to get things in perspective and one of the things that compels enormous admiration in looking back over the history of our Institute is to note the qualities of foresight and keen concern for professional standards which moved the pioneers in this Institute. They had no benefit of hindsight to aid them.Just over 75 years ago, a small group of men met in Broken Hill to discus.s the possibilities of forming an association of mining engineers. The moving spirit was Uriah Dudley, our first secretary, manager of the Umberumberka mine at Silverton. The first formal move to form an association of mining engineers came from the Amalgamated Mining Managers Association of Australasia. At the time, this association was a fairly new group, being 5 years old.It had been formed to try to raise the standard of management throughout the industry. Uriah Dudley and our first provisional president, John Howell, held their first talks in 1891 and further meetings at Broken Hill followed. The inaugural meeting, attended by 200 members, was held in Adelaide in April, 1893.

Jan 1, 1968

Typically, large volumes of data are collected during geotechnical investigations for mining projects but rarely is this done in a comprehensive manner that enables all aspects of the geotechnical environment to be evaluated. A geotechnical core logging process has been developed to record mechanical and structural properties of the rock mass. The method enables data for a wide range of rock properties and geotechnically significant major structures to be collected including rock strength, joint surface condition, fracture frequency and fracture orientation. The logging method is unique in that sufficient data is collected to enable the independent determination of all the major rock mass classification systems including rock mass rating (RMR), (Bieniawski 1976, 1989; Laubscher, 1990) Norwegian Geotechnical Institute (NGI) tunnelling quality index (Q) (Barton, Lien and Lunde, 1974) and geological strength index (GSI) (Hoek, Kaiser and Bawden, 1995). The logging system has been specifically developed to allow better and more precise appreciation of rock mass and structural conditions across the project area thereby optimising the use and application of the available geotechnical data and improving confidence in the outcomes of geotechnical investigations. This paper describes the core logging process with case examples showing how the logged data can be used for underground and open pit mine design.

Nov 25, 2010

By J Fut=

The rotary drilling of rocks is widespread technology in mining and in tunnelling. The paper describes the results of research by aim to find relationships between optimal drilling and sound signal of drilling machine. The optimisation criterion has been formulated as the minimisation of specific energy with maximal effective speed of drilling in process of the rock disintegration. The research in this field has been made on experimental drilling stand. Our monitoring system has measured following variables: the pressing force of core drill, the revolutions of drilling head, the length of drilling, the time, the power, and the acoustic signals. For measurement of acoustic signals have been used very sensitively sound meter MEDIATOR 2238. From this measurements have been processed acoustic spectrums. Then we are found relationships between optimal control of drilling and composition of acoustic spectrum. On base of experimental results, we can formulate the optimal control following: æTo achieve the minimum difference between the equivalent sound level at the load and idle modes only at the representative frequency (f = 1000 Hz)Æ. The representative frequency dependences on type of the rock New method based on these relationships enables the optimal control of drilling machine by using measured acoustic signals only.

Jan 1, 2003

The purpose of this paper is to describe briefly the clean-up procedure adopted at the treatment plant of Paringa Mining & Exploration Co. Ltd. at Kalgoorlie, Western Australia.A clean-up is carried out at the end of each four-weekly period, and all figures subsequently quoted are taken from a summary of the results of the eight periods ending 8th April, 1941.STRAKING AND AMALGAMATIONOf the total gold won 22· 77 per cent. is recovered by straking and amalgamation.The discharges of both the primary and secondary ball mills are pumped over a common set of five ten feet long by three feet wide straking tables, set at an angle of 10 degrees, before passing to the 14 ft. diameter by 30 ft. by 8 ft. Dorr bowl classifier.This classifier is in closed circuit with both of the ball mills, hence the whole of the circulating load of the fine grinding circuit, which approximates to 800 per cent., is required to pass over the straking tables. For convenience in handling, corduroy cloths are used in lengths of 5 feet, and are picked up and replaced by clean cloths at four-hourly intervals. The avaHable straking area provided is, therefore, 900 square feet, or approximately 3·30 square feet per original ton per 24 hours. The density of the pulp passing over the tables is about 54 per cent. solids, the area provided per ton of pulp per 24 hours being approximately o· 2() square feet. Washing of the corduroy cloths is carried out on the day shift only, about 800 lb. of strake concentrate being obtained daily.This concentrate is sluiced from the washing trough on the elevated straking floor to the 4 ft. by 2 ft. diameter amalgamating barrel located in the gold room below.The barrel is of standard design and is rotated at 25 r.p.m. It is charged each day at 4 p.m., and grinding of the strake concentrate at approximately 70 per cent. solids is continued until 8 a.m. the following day. The barrel is then stopped, and the contents generously diluted with water, and after a few minutes rotation some of the slime is carefully poured off through the small discharge hole. This dilution and decantation is repeated until a good deal of the valueless slime has been removed.A further quantity of strake concentrate is then charged to the barrel, which is allowed a further 16 hours grinding period. After again diluting and decanting, approximately 25 lb. of mercury and 15 lb. of lime are added to the charge, which is then given an amalgamation period of 2 hours before cleaning up.By the process of grinding, diluting and removal of slime by decanting...

Jan 1, 1941

(This paper reviews the reasons for and the principles followed in designing and constructing complete new surface works at the mine of the Zinc Corporation Limited, Broken Hill, New South Wales, and describes the layout, plant, buildings and services.)The Zinc Corporation mine produces high grade lead, silver and zinc sulphide ore. Lead and zinc concentrates are sent by rail to Port Pirie, where the lead is smelted and the zinc concentrate is shipped to Tasmania, England and other overseas countries.Some time ago consideration was given to the advisability of sinking an additional shaft. For some years the old main shaft had been working at full capacity and developments underground had indicated that the mine would eventually be capable of an output greater than that which could be handled through the shaft. It was therefore decided to sink a new main shaft and the site chosen was in footwall country 900 feet south of the old main shaft. The reason for the move south was so that the new shaft would be opposite the centre of gravity of the ore-bodies at depth. The size of the new shaft is 27 ft. ,6 in. x 15 ft., and the work was put in hand early in 1936.It was intended to haul the whole mine output through this shaft, which was 1,600 feet from the mill then operating. An extensive conveyor system thus became necessary unless a new mill was built near the shaft. A careful study of the situation was made by the management and consideration was given to requirements for expansion, the condition of...

Jan 1, 1940

By Elford H. S

Mr. H. W. GEPP said he desired to bring particular attention to this paper. The underlying intention of the Development and Migration Commission when the paper was prepared was to place at the disposal of Australian miners and metallurgists the story of the development of tin metallurgy as it had been advanced in other countries, particularly Great Britain. They had very considerable resources of low-grade tin-bearing metals in the eastern coast of Australia particularly, and they need not anticipate that tin was going to remain at the extremely low price at which they saw it to-day. The Commission felt that it was most desirable to place 'on record, and make easily available, the story of the treatment of comparatively low-grade tin ores in other parts of the world.Arrangements were made that the technical staff at Australia House, in conjunction with Mr. H. S. Elford; should collect this information so that in due course, when Australia awoke to an interest in low-grade deposits, of which there were many throughout Australia, this story would then not,have to be gathered from other areas and other places of the world. The -paper was a contribution which would turn out to be of very great value. He suggested to the younger members that this thorough contribution could be made the subject of study so that they would be ready to assist in the developments which must come. Mr. WM. APLIN said there was one point in connection with the paper upon which he would like to speak. While at Mount Morgan he had occasion to test some highly pyritic tin ore by flotation, with a view to separating the cassiterite from the pyritic mineral.Instead of accomplishing that, it was discovered that it would be possible to eliminate as much as 50% of the total weight of ore in the form of a pyritic flotation concentrate, which would contain...

Jan 1, 1930

By P W. Wypych

The iron ore industry faces significant challenges in the control of dust to meet emissions regulations and goals, as well as ensuring sustainable operations. This paper describes some of the different techniques and innovative technologies that are being developed and implemented to improve the suppression of airborne dust, specifically through the use of high energy micromist sprays. The utilisation of computational fluid dynamics (CFD) modelling and simulation is identified and described as a key enabling technology for an improvement in dust suppression solutions both from a level of understanding the source and flow of dust emissions, and for the development of new systems that can be used in the iron ore industry. CFD modelling is shown to be effective for modelling both spray dispersion and cross-wind effects, allowing designers to develop high-efficiency dust suppression systems with a greatly improved level of confidence when compared to traditional techniques. New high energy micromist technology is also outlined as a key element in developing high-efficiency dust suppression systems. Experimental results and industry applications are presented to demonstrate the significant improvements that can be achieved in suppressing or reducing airborne dust emissions.CITATION:Roberts, J M and Wypych, P W, 2017. Research into improving the efficiency of water spraying airborne dust control techniques in the iron ore industry, in Proceedings Iron Ore 2017, pp 359–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By E Kasai, T Nakamura, E Shibata

In the present study, formation of PCDD/Fs from carbon particles like æsootÆ, so called de novo synthesis, was experimentally simulated using the powder mixture of graphite and metallic chloride. Composite states of graphite and chloride particles were varied by the preliminary treatment, ie high-energy ball milling for different time or heating at different temperatures. These samples were subjected to the measurement of the rates of weight loss mainly due to the oxidation of carbon, the formation of absorbent organic chlorides (AOX) and the formation of PCDD/Fs at 300¦C. The amount of PCDD/Fs formation increased by applying certain pretreatments. Further, linear relationships were obtained among the formation rates of PCDD/Fs and AOX and the weight loss of sample. These results will give useful information to investigate the mechanism of PCDD/Fs formation from unburned combustible carbon and hydrocarbon in thermal processes.

Jan 1, 2002

The banded iron formations "jasper bars," jaspilites, banded hematite quartzites or banded ironstones, etc., as they have. variously been termed in Western Australia, constitute one of the most striking features of the Pre-Cambrian in this State. They occur in at least two distinct divisions of the Pre-Cambrian, viz., in horizons interbedded with quartzites, shales and thin bedded dolomite in the N~llagine (Proterozoic) Series; and amongst the Older Pre-Cambrian rocks, associated with the metamorphosed sediments of the Jimperding-Chittering Series, the Yilgarn Whitestone Series and the Mosquito Creek Series, and interbedded with metamorphosed basic lavas, tuffs and sediments of the Older prenstone or Kalgoorlie Series.In the Hamersley Ranges in the north-west of Western Australia banded ferroginous cherts are well developed amongst the horizontal sediments of Nullagine Age. These iron formations have recently sprung into prominence as they have been found to form the host rocks for important deposits of· blue asbestos. They are closely comparable with the unique crocidolite-bearing banded ironstones of the Cape Province, South Africa, and have been described elsewhere in some detail by the writer. (1) t .The banded iron formations with which it is intended to deal principally in the following pages, form most abundantly in the Central and Eastern Goldfields of Western Australia where they form portions of the Older Greenstone or Kalgoorlie Series of auriferous rocks. In these regions their chemical inertness and physical hardness provide considerable resistance to the agents of erosion and consequently they frequently stand out in strong topographic relief in otherwise monotonously flat or gently rolling country. These banded-iron formations have proved of considerable direct economic importance in the goldfields and in other portions of the State because of thei!! associations with 'gold, iron -and to' a lesser extent, manganese; whilst indirectly because of their peculiar nature, form and topographic prominence, etc, they have been of tremendous assistance to the field geologist both in the practical application of methods of geological mapping and in the' elucidation of geological structures. Finally, they have recently acquired a new importance in the specialised search for ore-bearing lodes or for structural information over areas of soil-covered country, as their form and composition make them ideal subjects for the use of either electrical or m!1-gnetic methods of geophysical prospecting.

Jan 1, 1941

By P Williams, S Flynn, R Birchfield, R Simcock, R Toft, P Comeskey

Direct transfer, or community translocation, comprises salvage and replacement of intact æsodsÆ of vegetation together with underlying soil. It has been applied to New Zealand mine sites restoration of native grasslands, wetlands, scrub lands, and forest. It is an equivalent technique to æinstant lawn or tree gardenÆ, commonly used in urban landscaping. Two to six m2 scoops of vegetation, with up to 0.7 m of soil attached, and including root plates of trees and shrubs, are relocated from stripped areas ahead of mining to sites prepared for restoration. Direct transfer uses hydraulic excavators or face shovels and dump trucks, possibly with the aid of bulldozers and other earthmoving machinery. The main advantages of direct transfer, compared with sowing or planting systems for mine site restoration, are the recycling of plant and soil materials which were often wasted by burying under overburden materials, a significantly faster revegetation process, and restoration of the whole ecosystem (plants, animals, birds, invertebrates, and microbes). The main disadvantages are higher costs of stripping and dumping, a greater degree of machine operator skill required, and scheduling becomes critically important. To illustrate the key principles, this paper gives examples of successes and failures of the technique for a variety of New Zealand mining situations. Direct transfer has been successful for a range of communities, from fern wetland and sub-alpine tussock grasslands to 5 m-tall beech forest under storey and seral shrub land, and from temperate to sub-alpine climates. Successful examples show both rapid recovery of indigenous vegetative cover and conservation of habitat for birds and invertebrates. Failures have resulted from excessive death of plants because of inadequate soil salvage depths, acidic leachates, inappropriate handling of stripped sods by inexperienced machinery operators, or prolonged drought conditions immediately following relocation. Change in plant species composition has occurred where clumps of vegetation are too far apart, or shifted plants were too small - in both cases invasive weeds have smothered the original vegetation. Changes in hydrology can also have significant impacts. Our experience indicates that the advantages of direct transfer far outweigh the disadvantages and is now used as the preferred restoration method, where practicable, at mines where it has been trialled.

Jan 1, 2000

The importance of reducing the moisture content of fine coal, the nature of the retained water, and the means of its removal are discussed. A statistical technique, using a balanced block design, was used to isolate the significant factors determining water content of a coal filter cake. The most significant factor was particle size distribution. A simplex evolutionary operation (evop) was used to determine the optimal quantities of additives required to produce the lowest moisture content for a selected coal size. For this optimum condition (18·6 Ib H20 per lOO Ib dry coal), additions of 0·045 Ib magnesium ion, 0·0026 lb Separan AP30, and 0·098 Ib Aerosol OT, per lOO Ib dry coal were required. The work illustrated the uses of a statistical evop technique for the determination of optimal conditions in industrial research projects.

Jan 1, 1970