Search Documents

By R. J. Wasilewski

THERMAL expansion of rhenium data have been reported by Agte et al.,&apos; and Medoff and cadoff,&apos; respectively, while the linear expansion coefficient was determined by Sims et Al.3 Denoting expansion coefficients parallel and at right angle to c axis by all and Al respectively, their weighted mean should be equal to dilatometric linear coefficient of a random polycrystalline specimen. The values reported for these coefficients are tabulated below: Since these values are in poor agreement, and because of anomalous expansion behavior observed in titanium 4 and chromium, a rede termination of the axial expansion was carried out. A Unicam 19-cm-diam high-temperature camera was used, with unfiltered CuK radiation. Camera calibration was carried out using at Pt wire standarde at temperatures up to 1100oC, the variation between indicated and true temperature being within the experimental error (estimated at <3oC) above 750o C. Rhenium Johnson Matthey spectrographic standard) was vacuum annealed at 1000 oC prior to X-ray diffraction experiments. Lattice parameters were obtained by least-squares solution using the reflec- tions (1232), (1015), (2024), and (3030) for all the patterns, and the additional reflection (2133) for higher temperature (400°C and above) patterns. The relative expansion data obtained are shown in Fig. 1, lengths of the vertical bars indicating the spread in the parameter values obtained by using various combinations of three spacings from the four or five measured. The data calculated from the equation of Ref. 2 are included for comparison purposes. Several specimens were used to obtain the above data, neither of them showing a significant parameter change after completion of the high temperature runs. Some parameter data and the corresponding expansion coefficients between 25 oC and the measurement temperature are tabulated below. The comparison of the present data with those previously reported shows reasonable agreement with the results of Medoff and cadoff2 within the temperature range covered by them (up to 1000 oC). The a values are appreciably higher throughout most of the investigated temperature range. The basal expansion is—in agreement with their findings—appreciably higher than that in the direction of hexagonal axis. The expansion coefficient, al, however, decreases rather more slowly with temperature than previously reported. The expansion along the c axis up to nearly 1000°C appears in excellent agreement. However, at higher temperatures there is a marked deviation towards higher expansion, reproducible between different specimens. Furthermore, there seems to be some irregularity in the variation of all with temperature, the apparent local minimum and maximum values at 510o and 1024o C, Table II, being well outside the experimental error limits. It must be stressed that the apparent discontinuity in the c parameter expansion is still insufficient to account for the expansion value reported by Agte et al.&apos; since a total expansion of close to 2 pct would

Jan 1, 1962

By W. A. James

NATURE endowed the Niagara Frontier with great resources but it was the molding of these resources by the early pioneers that assured its future development. This great industrial district of New York stretches along about fifty miles of shore line on the eastern end of Lake Erie and the Niagara River, embracing the two counties of Erie and Niagara, with the city of Buffalo about in the center. This location at the junction of the eastern end of the Great Lakes and the western boundary of the State, a great focal point of land and water, transportation, guaranteed the development of the Frontier. Although the first white settlers came to this section in 1784, it was not until after the turn of the nineteenth century that real development started. Perhaps the most significant influence in the early days was the completion of the Erie Canal between Buffalo and Albany in 1825. This then monumental achievement gave Buffalo an advantage in the race for the best trade route to the Western

Jan 1, 1938

By ARTHUR S. DWIGH

Discussion of the paper of W. W. NORTON, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August., 1914, pp. 1993 to 1999. ARTHUR S. DWIGHT, New York, N. Y.-Mr. Norton&apos;s chief argument is directed against the idea that the D. & L. sinter is any better material for the blast furnace than the H. & H. product. He supports this by citing two experimental furnace runs. Reducibility.-To discuss a furnace record like that quoted by Mr. Norton for the five days&apos; run in August, 1912, is manifestly difficult for an outsider, but a possible explanation for the poor reduction on Furnace No. 5, smelting D. & L. sinter, may lie in the fact that both sets of furnaces carried the same fuel charges. Other things being equal, if 11 ½ per cent. coke was right for the furnaces smelting H. & H. product, it Was too much for the furnace smelting D. & L. product, as I shall endeavor to show later, and incipient overfire, accompanied by higher leads in slag and matte, was induced. It may sound like a paradox to say that excessive fuel sometimes produces poor reduction, but it is a sad fact. In certain plants where practically the entire charge to the blast furnaces receives a preliminary treatment by being sintered on the D. & L. machines the peculiarities of this problem have had to be very carefully studied, for serious metallurgical difficulties presented themselves when the change was first made to D. & L. sinter in large quantities. Some of these plants had blast pots before they had D. & L. machines, and many opportunities were afforded for comparative study of this very point. There is reason to believe that, clue to the long period of blowing and the higher temperatures developed in the pots from greater mass action, the iron in the H. & H. product is present chiefly as Fe203, perhaps in the form of ferrites, while in the D. & L. product the iron is present as FeO. The fuel charge in the blast furnace must be so proportioned as to exactly meet the chemical and thermic requirements of reduction and melting. If ally of these functions have been performed before the material enters the furnace, a corresponding allowance should be made or the fuel balance will be disturbed and bad work will result. One of the functions of the coke is to reduce enough metallic Fe for the matte requirements, leaving the remainder of the iron as FeO to go into the slag. In smelting almost any other material than D. & L. sinter the iron must-be reduced from the higher oxides, Fe203 or Fe304, to the protoxide, FeO, before a true comparative basis is reached. Experience has shown that with about one-half D. & L. sinter on the charge the coke should-be cut about 10 per cent. This theoretical benefit is borne out by the practical blast-furnace results on a large scale in numerous plants. In fact, wherever this very important factor is ignored the evil symptoms of excessive fuel will be indicated,

Jan 11, 1914

By John V. Beall

STREAM pollution caused by waste waters from mineral industry operations is a problem that has grown up with the industry. Its importance to each operator is dependent on the amount and type of waste he dumps into the rivers and streams; on whether this waste pollutes the waters sufficiently to make them unfit for potable water, irrigation, and conservation of wild life; and on whether this waste makes a safety or health hazard. Through the years our growing population and industry have made increasing demands on the mineral industries, the suppliers of the raw materials on which our industries are based; and we have met these demands at some sacrifice to the natural beauty and cleanliness of our country. However, that is often the unavoidable nature of the business, and along with the increased use of our

Jan 1, 1948

By C. A. Stewart

PAGE. I. Introduction............ 241 II. Location. TopoGRaphy. and History....... 243 III. DescRiption of the Rocks......... 245 1. Altered Sediments.......... 245 2. Alaskite........... 246 3. Alaskite.Porphyry.....255 4. Quartz Dikes........... 257 5. Biotite.Granite.......... 256 6. Quartz.Porphyryl......... 260 7. Andesite........... 262 8. Miscellaneous Dikes......... 263 IV. Age oF the Rocks and Comparison with other Localities.. 263 V. AlteRation............ 265 1. Sericitization........... 265 2. Silicification........... 266 VI. StRuctuRes........267 1. Dip of the Limestone......... 267 2. Faulting........... 267 VII. Contact - metamorhism,.......... 269 1. Endomorphism.......... 269 2. Exomorphism......... 271 Recrystallization and Loss of Color...... 271 New ,Minerals.......... 272 Addition of Material........ 274 Volume.Changes.... 276 Locus of Metamorhism........ 277 Method of Precipitation.........278 VIII. ORe-Deposits............ 278 1. Contact-Metamorphic Copper.Ores,..... 279 General..........279 Shape and Distribution........ 279 Minerals........... 281 Secondary Enrichment........ 282 2. Disseminated Copper.Ores........ 283 3. Origin of the Copper.Orcs........ 284 4. Lead-Silver Ores.......... 287 IX. Bibliography............ 288

Jan 1, 1913

The Mississippi river was discovered by French explorers that came southwestward, by way of the Great Lakes, from eastern Canada. Vignan, Joliet, De Champlain, and others of the French pioneers in the first half of the seventeenth century, dreamed of a short cut to China by means of the great waterways they explored. In a geographical book published in London in 1726 by Daniel Coxe an account is given of "a new and curious discovery and relation betwixt the river Meschachebe [Mississippi] and the South Sea, which separates America from China, by means of several large rivers and lakes". Louis Joliet, a fur-trader, and Jacques Marquette, a Jesuit missionary, reached the Mississippi and paddled their canoes on its broad waters on June 17, 1673.* They descended the river as far as the entry of the Arkansas tributary, and then returned overland to Canada, being deterred from going farther south by reason of Indian hostility. Several years later Robert de La Salle, a French trader, starting from Quebec, went westward to Lake Michigan and thence to the Illinois river, which he and his comrades descended in their canoes to the junction with the Mississippi, and then followed it to the sea. They reached the Gulf of Mexico on April 9, 1682. Thus the great central waterway of North America was made known. These French-Canadian voyageurs, or boatmen, traded with the Indians for furs in the Upper Mississippi valley, and when in need of bullets they noticed the outcrops of lead ore, from which, probably in the last decade of the seventeenth

Jan 1, 1932

By George W. Riter

OUR mineral-land laws need revising so as to provide definite title at the outset to the mineral deposits within any definite piece of land. The laws as they now stand, especially those applicable to lodes, breed uncertainty as to rights of possession prior to patent; and to my mind this is the worst feature of all, worse even than the apex bugbear. It is now almost impossible for anybody to tell-with certainty what mineral rights exist within any area that is not covered by patent, or whether any valid rights exist at all. Our system is unique in permitting individuals to appropriate and exploit mineral lands of the public domain without notice of any kind to the Federal government, and to relinquish them without any ceremony at all. The result is a clouded record that cannot be cleared up until each claimant is put to some sort of final proof. In order to accomplish this, new Federal legislation will be required. The requirements for a mineral survey and the proceedings for patent have always been cumbersome and expensive; and perhaps out of regard for the poor claim owner, who can ill afford the outlay for that sort of thing, the law does not require him to go. through it unless he chooses to do so. Consequently, every active mining district has become encumbered with tangled groups of doubtful or conflicting locations, whose rights and boundaries, when any valuable ore is found, must usually be determined by lawsuits that are as expensive and as distressing as the stakes are high. So deeply has litigation entered into our mining system that a claim whose rights have never been disputed would probably be set down offhand, by $miner of the old school, as of no value. Think of the litigation over rights of possession on the Com-stock lode—12 leading companies involved &apos;in an aggregate of 245 suits within a period of less than eight years! Ambiguous local records; the chance of erroneously placed or obliterated monuments; doubt as to the sufficient performance of the statutory annual labor; uncertainty as to prior conflicting or overlapping locations; anxiety as to the changing attitude of the Department of the Interior and the Forest Service—such considerations as these make an unpatented mining claim an unclean thing in the eyes of possible investors. Is it any wonder that they keep themselvesand their money at a safe distance,

Jan 1, 1915

By Samuel Lasky

THE writer has been interested in determining the mineralogic dis-tribution of silver in the base-metal ore of the Ground Hog mine of the Asarco Mining Co. in the Central mining district of New Mexico.1 This ore consists of a varitextured mixture of sphalerite, chalcopyrite, galena and pyrite in a quartz gangue. The average ore contains 14 per, cent of zinc, 9.5 per cent of lead, 5 per cent of copper, and 10 oz. of silver per ton. Generally it is accepted that the silver in ores of this type, in which no definite silver minerals can be recognized, is contained in the base-metal minerals. Published assays of pure mineral specimens from many dis-tricts show that each of the base-metal minerals contributes in some degree to the total silver content of the ores, and to determine the pro-portionate amount contributed by each mineral in any specific ore it has been the practice to assay selected specimens of each mineral, the purity of which has been determined microscopically. There being no such assays available for the Ground Hog ore, and it being impract cable to have enough of them made to give average results, the writer resorted to a mathematical attack upon composite assays of large quantities of ore and concentrates. Surprising results were obtained, and it is the threefold purpose of this paper to present these results, to describe the mathe-matical method used, and to point out the value of using this method even when assays of pure specimens are available.

Jan 1, 1934

By John S. Crout

TWENTY-FIVE years ago the training of an engineer was of interest solely to the educator and to the student entering the field. At that time the engineer&apos;s position in society was relatively simple. His training emphasized design and operation and he expected to enter industry to handle the engineering problems of raw materials production, mechanical and product design, and the operation of power plants, factories, transportation and communication systems, and similar phases of industrial activity. He was not concerned with or particularly interested in the problems of management, administration, sales, publicity, industrial relations, or of legislation. To a large degree he was content to leave these matters to self-made businessmen, or men trained in law, finance, or commerce. That period in the evolution of the engineer is now history. It is generally conceded that the modern world is dependent upon engineering technology for its day-to-day survival. The continued operation of facilities on which mankind relies is dependent upon the functioning of mines, utilities, chemical plants, and other factories, all of which require the knowledge and the skills of trained engineers. Thus from a purely mechanical point of view, the engineer has become indispensable to

Jan 1, 1947

PRODUCTION of nonmetallic mineral raw materials used by the fertilizer, ceramic, chemical, and construction industries and many others, was greater during 1953 than in any previous year. Production of fertilizer minerals was the highest in history despite somewhat decreased consumption in the second half of the year. Marketable phosphate rock production increased 10 pct to an estimated total of 13.1 million LT, valued at $78.5 million, and potash production was estimated at 1.8 million tons of K2O equivalent, valued at over $60 million. Crude gypsum output exceeded the 1952 total and approached the record of 8.66 million tons mined in 1951, with indications that 1953 will show a new all-time high. Gains and losses among gypsum products were irregular, with major gains in plate- glass and terra-cotta plasters, sanded building plasters and miscellaneous building plasters, and principal declines in base-coat plasters, prepared finishes and tile. Lath and wallboard outputs were each about 20 pct higher than in 1952.

Jan 2, 1954

By Walter Morley

This paper is a record of the first of a series of tests on sulfide minerals to be made by the metallurgical department f the University of California. The purpose of the tests here recorded is to determine the action of standard oils, oil mixtures, and addition agents on the flotation of pyrites. The question of the commercial value of pyrite was not considered. Of the many factors affecting flotation, only two-the oil and the other agent used-were made variable. The flotation agents used are given in the accompanying table. PENSACOLA TAR AND TURPENTINE CO. (PENTARCO) NON-POL., SP. Dis. REF. PER No. KIND GR. POINTS INDEX ?VISC. CENT. 200 Refined wood creosote oil 0.965 105-275 1.5096 1.7 7-8 350 Crude pine wood oil 1.019 70-345 1.525 2.9 4 75 Crude wood turpentine 0.887 65-217 1.456 0.9 10-12 80 Crude pine oil 0.911 70-232 1.4894 1.1 8 750 Heavy pine tar oil 1.063 165-350 1.557 41.0 400 Wood creosote oil 1.025 190-360 1.4977 2.9

Jan 7, 1921

By AIME AIME

HEREWITH is presented a preliminary report of a special committee, consisting of Erle V. Daveler, Paul D. Merica, and C. H. Mathewson (chairman), dealing with sundry matters of which many are of vital interest to all members of the American Institute of Mining and Metallurgical Engineers. As the report states, the initial purpose of the investigation was to determine ways and means to stimulate "the welfare and growth" of the Institute of Metals and Iron and Steel Divisions. However, it soon became apparent to the committee that most of the problems and possible correctives were of no less vital concern 1o members of the other Divisions and to the "unattached" group of members. Consequently, the Committee has authorized publication of the report and invites written comment from any member on the specific recommendations or on any other phase of the broad subject.

Jan 1, 1943

By AIME AIME

COAL occupied a large place in the technical sessions of the Institute at its annual meeting for in addition to three sessions specifically de- voted to coal the two sessions on mine ventilation and the two on ground movement and subsidence, which are reported under their own headings, were primarily concerned with coal. The first session on coal was a joint one with the Iron and Steel Division, on Wednesday afternoon, with F. H. Crockard and J. R. Campbell presiding as joint chairmen and the latter actually officiating. The principal topic of discussion was G. S. Scott&apos;s paper "Evaluation of Coal for the Making of Blast- Furnace Coke," which has been published as T. P. 159. The author made a brief statement of its con- tents to start the discussion and the chairman, after briefly reviewing it himself, called on C. A. Meissner to start the discussion. He briefly reviewed the economic factors in the use of coal for coke-making, saying that not only .does the removal of 1 per cent of ash from the coal reduce the cost of pig iron 12 or 13c. per ton, but it also permits coke of satisfactory structures to be made from a coal which otherwise could not be used. He stressed the importance of uniformity in blast-furnace fuel and discussed the benefit of mixing different coals as raw material for the coke oven and cited experience with Illinois coals.

Jan 1, 1929

By A. B. Stickney

UPWARDS of 200,000 engineers in this country are sufficiently interested in engineering as a profession to have joined a society, but not over 10% of them belong to any one society. There is a widely-felt need of an over-all organization of all the societies to act as spokesman for all engineers on matters of common concern. On a local basis, over 100,000 engineers in 35 metropolitan areas have organized themselves into local councils, and are doing an effective job of intersocietal co-operation within their sphere of activity. In the last few years much has been said and written about a similar organization on a national scale. Everybody wants iteverybody is talking about it-it&apos;s in the air-it&apos;s coming-it&apos;s inevitable. Although it is no longer necessary to talk about why or whether there should be such an organization, there is no such unanimity about what it should be like. This paper outlines a proposed organization by answering four questions-who, how, what, and who will pay for it.

Jan 1, 1946

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments. and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table I are reported the compositions of the core and cladding alloy for the material used for the experiments. Table i.—Chemical composition of R~OI Used for the Experiments Element Core Cladding Cu........................ . 0.01 Fe......................... . 0.42 Si......................... 0. 0.71 Mg........................ . 0.99 Mn ........................ . 0.54 In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion. Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R~OI varies with the gauge, as shown in Table 2, several gauges were investigated. Material and Procedure he material used was sheet of the following gauges: o.o2~, 0.040, 0.064, 0.102, 0.170 Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: glo°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After zoo min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1946

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments. and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table I are reported the compositions of the core and cladding alloy for the material used for the experiments. Table i.—Chemical composition of R~OI Used for the Experiments Element Core Cladding Cu........................ . 0.01 Fe......................... . 0.42 Si......................... 0. 0.71 Mg........................ . 0.99 Mn ........................ . 0.54 In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion. Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R~OI varies with the gauge, as shown in Table 2, several gauges were investigated. Material and Procedure he material used was sheet of the following gauges: o.o2~, 0.040, 0.064, 0.102, 0.170 Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: glo°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After zoo min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1946

By Oscar A. Glaeser

INDUSTRIAL relations in the United States Smelting Refining and Mining Company&apos;s Western operations covers the field of personnel and labor relations, and the principal aims are to render service to the employes of the Company and to its operating departments. Accident prevention Safety is a primary function. A safety engineer is employed at each operation. The wholehearted support of Company officials, staff, and the working force has been most successful in preventing accidents. Constant vigilance has been combined with a policy of building safety into all operating activities whether these are in the construction of a new facility, the developmnt of a mining system, or the direction of the working force. That this policy has produced results is attested to by the fact that the accident frequency rate at the Company&apos;s major mining operations in Utah has been reduced approximately 75 per cent in the ten-year period ending Dec. 31. 1946.

Jan 1, 1948

By G. W. Crane

WHEN ore was discovered on the Tintic Standard property in the spring of 1916, new developments were immediately started both north and south of that property, on the supposition that in East Tintic the ore would be found to occur in northerly trending channels, similar to those so characteristic of the older camp. But 9 years of developments have failed to establish the existence of such a channel. This is due undoubtedly to important differences in the geology of the two camps, that were not recognized, and is indicative of the danger in the general tendency toward interpreting the geology of East Tintic too strictly in terms of that of the older camp. It should not be forgotten that while the two sections have had practically the same geological history, the net results of a long series of geologic processes have developed in them conditions that differ so widely and in so many particulars that the necessity of regarding them as essentially different districts seems apparent. In an effort to emphasize this fact, this paper is devoted chiefly to a comparison of the geological conditions as found in the two camps and is addressed more particularly to those familiar with the geology of the Tintic district. Following a short description of the several ore discoveries and of the Tintic Standard mine is a brief discussion of the evidence of ore channels in East Tintic. For my information regarding the Tintic Standard mine, I am indebted to the courtesy and generous assistance of Messrs. Wade and Snow of the Tintic Standard Mining Co.

Jan 9, 1925

By W. W. Gerberich, P. L. Hemmings, V. F. Zackay

ThE strain-induced martensitic transformation may be used to attain desirable combinations of strength, ductility, and fracture toughness. One of the parameters is the relative stability of the austenite. For example, it has been shown by Zackay et al.1 that the volume percent of strain-induced martensite is related to the combination of strength and elongation obtained. It has also been shown that the degree of transformation is an important factor in the crack propagation resistance of metastable austenitic steels.2 Considering both tensile and crack-propagation tests, it was of interest to see if there was any functional relationship between the amount of strain and the volume of strain-induced martensite. Previously,9 it had been shown that at room temperature, there was a relationship between uniaxial tensile strain and the volume percent of resulting martensite given by The data were obtained by plastically elongating tensile samples to a certain strain and then measuring the field strength to determine the strain-induced ferromagnetic volume. This was accomplished for two conditions having yield strengths of 229 and 233 ksi. The nominal composition of this material was 9Cr-8 Ni-3 Mo-2 Mn-2 Si-0.25 C-0.09 N. In evaluation of the strain-induced martensite at a crack tip: the question arose as to whether Eq. [1] would also be valid under triaxial stress conditions. Tests were conducted on 1/2-in. thick plate material having a composition of 9 Cr-8 Ni-4 Mo-2 Mn-2 Si-0.27 C. It was found that sectioning, polishing, and etching of fractured specimens could reveal the strain-induced martensite occurring at a crack tip. Care had to be taken to minimize the final polishing steps so as to avoid a smeared layer of strain-induced martensite. The method for taking metallo-graphic samples from fractured crack-line loaded type samples is shown in Fig. 1. Observations of the strain-induced martensite occurring at room tem-

Jan 1, 1970

By V. H. Wilhelm

The outstanding event in the California petroleum industry during 1931 was the continuance of curtailment of crude oil production, which directly reduced drilling and well repair activities. Although all objectives were not attained, a very close balance between supply and demand was maintained during the period of maximum requirements, but the decline in intercoastal and export shipments caused an overproduction during the last half of the year, which indicated that California production would necessarily suffer further curtailment after the end of the year. A new peak in potential crude oil production of 1,187,600 bbl. per day was reported in August and at the close of the year the California potential was 1,069,000 bbl. per day, the shut-in light oil amounting to practically 425,000 bbl. per day and the shut-in heavy oil amounting to about 150,000 bbl. per day. Fig. 1 depicts these conditions and also shows the production and curtailment situation since the inception of proration in California. The December, 1931, potential figure of 1,069,-000 bbl. per day was arrived at after the most careful deliberation by a number of committees, selected to check the potential of practically every well in the state. Continued overproduction in the first three months of 1931 and the inadvisability of building more storage, together with the inability to obtain the proper amount of curtailment in town-lot fields, such as Long Beach, Santa Fe Springs and Playa del Rey, prompted the major oil companies to inaugurate a price reduction in crude oil. This cut caused prices to reach the lowest levels since 1915, and instigated the formation of an oil sales agency, composed of independent operators, which is known as the Oil Producers Sales Agency. The purpose of this organization is to procure a market for its members at reasonable prices, advise them of market conditions and aid them in controlling the amount of oil available for sale. Marketing of oil produced by members began on June 1 and independents controlling" about 160,000 bbl. per day of production had become members by the end of the month.

Jan 1, 1932