Search Documents

By H. J. Hager, P. H. Haskell

For the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wet-table plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to re-treat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both byproduct coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to 100 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands I in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within +0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation's mines could not clean the he sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to o. The washed table coal is mixed with the 3 to ¼-in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1942

By H. J. Hager, P. H. Haskell

For the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wet-table plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to re-treat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both byproduct coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to 100 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands I in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within +0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation's mines could not clean the he sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to o. The washed table coal is mixed with the 3 to ¼-in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1942

By A. E. Martin, Gerhard Derge

IF the molecular constitution of molten slags were better known, the nature of chemical reactions in slags and between slags and metals could be better understood and as a consequence might be better controlled. Constitutional information can be obtained by studies on either the molten or the solidified slags. Valuable as the studies on solidified slags admittedly are for many purposes, especially as control methods in steelmaking, they are always of questionable value in giving information on the molecular constitution of liquid slags. However, the characteristics of molten slags such as viscosity, rates of diffusion, and electrical conductivity can be determined experimentally and interpreted along with other knowledge on slag-metal and slag-gas reactions so as to provide direct information on liquid slags. Metallurgists are accustomed to regard reactions in molten slags as involving only neutral molecules, whereas it is quite possible that ionic constituents are actually involved. For example, the dissociation of calcium silicate usually is represented as Ca2SiO4 = 2CaO + SiO2 although a reasonable alternative would be to write Ca2SiO4 = 2Ca+2 + Si04-4 Such ionic dissociation has been suggested frequently without adequate experimental proof. This paper deals especially with electrical conductivity measurements on slags of the blast-furnace type. These measurements were made to determine whether or not slags are ionized and, if so, to provide a qualitative estimate of the extent of ionization. Electrolysis experiments that indicate the identity of the ions present are also reported. Since the presence of ions has not been considered carefully in modern slag studies, the relevant literature will be reviewed. REVIEW of LITERATURE In 1906 Aiken1 obtained a patent for a continuous process of producing iron electrolytically by passing a direct current through a bath of FeO-SiO2 to which iron oxide was added periodically to maintain a uniform concentration. The patent also included the addition of CaO and MgO to the bath to lower its melting point. The silicate melts involved were thus in the same system as basic open-hearth slags but with higher FeO and lower CaO contents. Electrical conductivity measurements were made on some molten silicates by Doelter2 in 1907. Natural silicates, such as

Jan 1, 1943

By J. T. Pardee

INTRODUCTION PLACER is a Spanish word, the definitions of which include "an extensive bank of sand or gravel" and "a place where currents of water deposit particles of gold."l The term, probably first used in the western hemisphere by Spanish or Mexican gold miners, is now generally applied to all detrital deposits that yield valuable minerals by washing. In the Western States placer products other than gold, including the silver alloyed with it, are chiefly sapphires, produced in Montana, and platinum alloys recovered in California and Oregon. During the war tungsten ore (scheelite) was obtained from placers in the Atolia district, California, and a number of diamonds have been found in the Sierra Nevada gold belt. Small amounts of stream tin have been produced in the Black Hills of South Dakota and a little monazite sand in the Boise Basin. Idaho. Magnetite, chromite, ilmenite, zircon, and other useful minerals are more or less abundant in the beach placers of the Pacific coast and in the heavy residues of placer mining elsewhere, but the problems of profitably separating and marketing them remain to be solved. Minerals of lead, quicksilver and other metals occur in many of the placers and although not plentiful enough as a rule to be worth recover-ng, their presence has, in several instances, led to the discovery of valuable lodes, notably at Leadville, Colorado. Historical summary.-In New Mesico, Arizona, and Southern California, placer gold was mined by Mexicans and Spanish priests in the first half of the 19th century or earlier. With these exceptions history of placer mining in the Western States begins with Marshall's discovery of gold in northern California in 1848. During the next twenty years placers were found in all of the principal mining districts that are known today. The richer deposits were soon mined out but a relatively large production was maintained from the leaner deposits chiefly by hydraulic

Jan 1, 1933

By Scott Turner

AS IN OTHER lines of engineering, progress in mining was influenced during 1931 by the world-wide economic depression. Low-metal prices ? resulted in active efforts to reduce production costs of base-metal mines. Probably the chief factors in reducing costs were the greater efficiency of labor, due to better relations between management and workmen, to the scarcity of jobs, reduced wages in most base-metal mines, and to lower overhead expenses secured by drastic economies. The use of mechanical equipment continued to increase, due to more efficient designs and a better practical understanding of the applicability of such equipment to requirements. With one exception, there were no startling innovations in stoping methods, but there was notable progress in the better adaptation of mining methods. In the United States, no large new base-metal or silver mines came into production during the year. At a number of mines, output was curtailed, and operations were discontinued at several important producers. On the other hand world-wide interest in gold was stimulated, as evidenced by increased output from producing mines, the reopening of some old properties, and intensive prospecting for new deposits. Mining methods at several gold mines in the United States and Canada were modified or changed to obtain a higher extraction of ore or to meet the need for additional support of the mine workings at depth. Permanent record of improvements in mining practices has been made during the year by the Federal Government; the industry thus has available for its use more detailed information than ever before. This work was done through cooperation of the mining companies and their representatives with the United States Bureau of Mines, whereby many papers descriptive of practices and costs at individual mines have been published. The Bureau's program of describing methods and costs at the more important mines (those producing in excess of $100,000 annually) is nearly completed, but papers will be issued concerning such additional mines as may possess particular interest because of novel methods, exceptional conditions or operating results, and others to supplement reports already issued. In this way, an interesting record of the results of changing conditions, or innovations in methods, will be made available.

Jan 1, 1932

Jan 1, 1920

By Carl Floe

THE possibility of separating the various constituents of mixed ores or metalliferous products by differentially producing their soluble sulfates has not received the consideration that it deserves. The production of the soluble sulfate may be accomplished by baking the ore with sulfuric acid or by treating it with gases containing oxides of sulfur. This paper is primarily concerned with the first method. The procedure used was to mix the material with a solution containing a definite weight of sulfuric acid, baking the mixture at various tempera-tures and then leaching out the soluble sulfate with water. The amount of acid used was calculated to produce certain desired soluble sulfates. The temperature of baking depended on the decomposition points of the sulfates involved. The object was to prevent the formation of or to decompose certain sulfates while leaving a maximum quantity of another sulfate in a water-soluble form. This procedure has two possible advantages over the ordinary method of leaching with an aqueous solution of sulfuric acid. First, a more selective leach may be obtained, and second, the higher temperatures and stronger acid concentrations involved will permit a better recovery of materials that are difficultly soluble in relatively dilute aqueous sulfuric acid solutions. The method of sulfuric acid baking followed by water leaching is not new, as it has been applied in the treatment of various metalliferous materials such as the recovery of cadmium from flue dust1, the re-treat-ment of zinc leach residues2 and the working up of electrolytic slimes3.

Jan 1, 1936

By Arthur A. Center

WAR demand- motivated developments in the zinc industry during 1942. Stocks of Prime Western were built up and High-Grade remained tight. The Prince The Prime Western stocks are expected to be cut down and the demand for High-Grade more easily filled as the Depue reflux plant of the New Jersery Zinc Co. increases - production. Subistition of steel for brass in artillery shell cases will have a considerable effect on the zinc situation of the country one estimate of the saving in zinc in 1943 by this substitution being a little under 100,000 ton, of metal. The metal saved will, of course be High-Grade. If the substitution occurs, the present tight situation in High-Grade may be entirely relieved as new production comes on the market and zinc may find itself approaching a situation as comfortable as that of lead provided the supply of zinc-hearing raw materials is sufficient to keep all reduction plants tip to capacity production. The premium price of the per pound of zinc over set quotas which went into effect early in 1942, helped to bring about the new lead-slag-fuming plant and other new sources of raw materials.

Jan 1, 1943

By H. Stigzelius

FINLAND'S recent mining history is both dramatic and pitiful in its shifting fortunes, dominated as it has been, by the country's proximity to the border zone of opposing dictatorships and social traditions; Fascism to the south, Communism to the east, and Democracy to the west. After 108 years under Russia's more or less harsh rule, Finland gained its democratic independence during the 1917 revolutionary strife in Russia with the official help of Germany and spontaneous help of other neighbors. The young nation was attacked by Russia in 1939 and again in 1941. It is common knowledge how the Finns fought with everything they had and everything they could get against their overwhelming adversary, and how by force of circumstances they landed in the Axis camp in 1941. Finland has never been known as a mining country in the same way as near-by Sweden, whose abundant iron and copper smelters during long periods so greatly contributed to the nation's welfare. Its largely barren, Archaean-granite geology long seemed forbidding. Some mining was done, to be sure; copper and tin at Pitkaranta near the Russian border, and lead and copper at Orijarvi. But towards the end of the last century the absence of a single producing mine cast a pessimistic shadow of truth over the Finnish poet Runeberg's words, that

Jan 1, 1946

By G. H. BUCHANAN

ALTHOUGH the nomenclature of the chemical tools of flotation is probably familiar to you, it will do no harm to review it; . In order to make the terms more real I have employed an illustration which likens flotation to an old-fashioned balloon ascension, such as we witnessed in boyhood at the county fair. The mineral to be floated is the aeronaut, conspicuous in his gilt-spangled tights, who is to be separated from you and me and the other small boys who are standing about, said boys being the g-a-n-g-u-e, or g-a-n-g, as we would have spelled it. The oil film surrounding the bubble is the counterpart of the silken fabric of the balloon, and bubble and balloon will rise for. the same reason, namely. that the fluid outside it is heavier than the fluid within. In flotation reagent nomenclature the material of which the bubble is made is called the "frother.",

Jan 1, 1930

By H. C. Ray

ABOUT the beginning of 1930, coal preparation had reached the stage where the cleaning of coal by liquid or air had become the order of the day. Since that time many new preparation plants have been installed in spite of the years of depression in the coal industry, and this is indicative of a trend wherein the coal producer found it expedient to manufacture a cleaner product in order to compete with other fuels. It was also about 1930 that, because of the difficulties encountered with fine coal in cleaning plants, dust collectors came into use. Both cleaning plants and dust collectors, therefore, were much discussed at the engineering meetings of the early 1930's. During these meetings the many advantages to be gained through the use of dust-collecting systems were pointed out by Hebley,1 Appleyard2 and others. The great possibilities of new markets for this product were emphasized and discussed at the same time; however, the disposal of the collected dust remained a problem. Since the purpose of dust collecting is to improve the preparation and, consequently, the salability of the coal, it seems illogical to return the collected dust to any of the coal being prepared for market use, as is done in preparation plants that include dust-collecting systems. The logical thing is to dispose of the dust in some useful and practical manner outside of the tipple. As a practical matter, this can be done in one or both of two ways; either by consuming the dust at the mine's own power plant or by marketing the dust direct to the consumer. The latter method not only offers the greatest opportunities, but is the most important, because of inequalities that may exist between the quantity of dust collected and the consuming capacity of the mine's power plant. In considering the more important marketing possibilities, we are confronted immediately with the problems connected with the handling and transportation of so fine a material. It is this problem, rather than the problem of finding new markets, that has been responsible for the lack of progress in the matter of dust disposal. It is the purpose of this paper to point out again some of the potential market outlets, and also to describe an existing system of handling and transporting coal dust. To the best of the writer's knowledge, this is the first and only operation in this country that has handled fine-mesh coal in bulk 50-ton lots direct to the consumer. POtential Markets for Fine-mesh Coal Dust In general, the potential market outlets would include any operation of which the pulverization of coal is a necessary part. To be more specific, a few of the better known operations of this type must include: colloidal-fuel plants, briquetting plants, "sea coal" distributing plants, water-purification plants and, obviously, pow-

Jan 1, 1944

By H. C. Ray

ABOUT the beginning of 1930, coal preparation had reached the stage where the cleaning of coal by liquid or air had become the order of the day. Since that time many new preparation plants have been installed in spite of the years of depression in the coal industry, and this is indicative of a trend wherein the coal producer found it expedient to manufacture a cleaner product in order to compete with other fuels. It was also about 1930 that, because of the difficulties encountered with fine coal in cleaning plants, dust collectors came into use. Both cleaning plants and dust collectors, therefore, were much discussed at the engineering meetings of the early 1930's. During these meetings the many advantages to be gained through the use of dust-collecting systems were pointed out by Hebley,1 Appleyard2 and others. The great possibilities of new markets for this product were emphasized and discussed at the same time; however, the disposal of the collected dust remained a problem. Since the purpose of dust collecting is to improve the preparation and, consequently, the salability of the coal, it seems illogical to return the collected dust to any of the coal being prepared for market use, as is done in preparation plants that include dust-collecting systems. The logical thing is to dispose of the dust in some useful and practical manner outside of the tipple. As a practical matter, this can be done in one or both of two ways; either by consuming the dust at the mine's own power plant or by marketing the dust direct to the consumer. The latter method not only offers the greatest opportunities, but is the most important, because of inequalities that may exist between the quantity of dust collected and the consuming capacity of the mine's power plant. In considering the more important marketing possibilities, we are confronted immediately with the problems connected with the handling and transportation of so fine a material. It is this problem, rather than the problem of finding new markets, that has been responsible for the lack of progress in the matter of dust disposal. It is the purpose of this paper to point out again some of the potential market outlets, and also to describe an existing system of handling and transporting coal dust. To the best of the writer's knowledge, this is the first and only operation in this country that has handled fine-mesh coal in bulk 50-ton lots direct to the consumer. POtential Markets for Fine-mesh Coal Dust In general, the potential market outlets would include any operation of which the pulverization of coal is a necessary part. To be more specific, a few of the better known operations of this type must include: colloidal-fuel plants, briquetting plants, "sea coal" distributing plants, water-purification plants and, obviously, pow-

Jan 1, 1944

By James A. Beck

Phosphorus is essential to all life processes and therefore to the existence of man. In this role, there are no substitutes for phosphorus. In a commercial sense, phosphorus and its compounds are important to our entire economy, both in agricultural and in nonagricultural applications. The world's phosphate requirements are met by mining phosphate rock. Two general types of phosphate ore deposits are commercially important-igneous and sedimentary. Igneous deposits generally are more difficult and more expensive to mine than sedimentary deposits and are of importance mainly in the USSR, North Vietnam, and South Africa. Approximately 15% of current world production comes from these deposits. Over 80% of world production is from the pellet sedimentary deposits of Florida, North Africa, and elsewhere. Guano, the second type of sedimentary deposit, is produced in South America but is declining in world importance. Production Production of phosphate rock was reported in 31 countries during 1972. However, about 80% of world output is produced in three countries: the United States, the USSR, and Morocco (Table 15.2A.1). Throughout the past 20 years, between 75% and 80% of world output has been produced by these three leading countries. Between 1948 and 1972 world production increased at an average rate of 10% per year, from 21.5 to 103.9 million tons. Growth was quite steady at 6% per year through 1963, but in the 5 years from 1963 to 1968 production increased 11 1/2% per year. Since 1968 production has increased about 91/2 % annually. Since 1948 several new phosphate mining ventures have been developed in Senegal, Togo, Israel, and North Vietnam. In the same period, only one important phosphate deposit, on Makatea Island, has been mined out and closed. A number of other phosphate mining ventures are in various stages of planning and development. The most important new venture in phosphate mining is in the Spanish Sahara. New mining capacity is expected also in Syria, and serious investigation is in progress in Peru, India, Turkey, and Australia. Major expansion of existing operations is expected in Morocco, Russia, Tunisia, Israel, and Jordan. Consumption Historical data on world consumption of phosphate rock are not available in detail, but world consumption of phosphate has closely paralleled world production in the past two decades. The United States is the world's largest user of phosphate rock, accounting for 30%

Jan 1, 1976

By P. G. Nahin, A. Grenall, R. S. Crog, W. C. Merrill

A progress report of an experimental investigation into the role of clay in reservoir performance is presented. The Paper gives some of the reasons for considering clay as a significant component and outlines the objectives of a broad field of stud) which it is intended to pursue. Descriptions of the analytical methods used are given; these include X-ray diffraction. elec tron miscroscopy, thin section petrography, infrared spec-troscopy, and cation exchange analysis. A suite of the more important clay minerals has been assembled and characterized l~y these methods for use as standards in core analysis. From the data obtained it appears that although no one method of analysis is diagnostic for all of the clay minerals the infrared technique shows considerable promise in this direction. For the present, one or more supplementary methods should be used to confirm the clay mineral identifications. The methods of analysis are applied to field cores taken from repesentative and widely differing strata especially as regards their susceptibility to damage by fresh water. well.; completed in the stevens and Gatchell zones in San Joaquin valley are I,articularly clear-cut examples of this behavior with stevens zone wells being more adversely affected by fresh water. cores from these zones have been studied and are discussed. It appears that differences in this behavior can be ascribed to differences in the nature of the contained clays. The value of the infrarecl spectra of the clay fractions in establishing the identity of the predominant clay minerals is given particular emphasis. INTRODUCTION It is a challenge to the technical resources of the petroleum industry that when the economic limit of production is reached, from 40 to 70 per cent of the oil in California reservoirs remains unproduced even by use of the best presently known methods of recovery. The magnitude of this abandoned volume of oil can be appreciated when it is considered that to 1950 in excess of 8 billion bbll has been produced from California reservoirs with estimated economically recoverable reserves in known fields and pools totaling nearly 4 billion bbl.24 If for every barrel of oil produced there is at least another barrel still in place, it is evident that the revenue obtained from the recovery of only a .few per cent of this volume would repay the cost of the required research manyfold. From well completion experience. production behavior, and a growing body of laboratory data it now appears certain that the mineral composition of a producing stratum has an important bearing on the productivity and ultimate yield. In addition to the organic component and water, the cores con,ist of gravel, sand. silt, and clay" in diverse variety of (a, composition and (b) texture. It is the composite effect of these two factors which is probably responsible in large measure for the way in which the oil flows to the well. The role of the clay and fine-size accessory minerals is not clear but there is a growing opinion, based on their physical and chemical properties, that it is a significant one. of particular importance are the prime facts: 1. The silt and clay fractions of the reservoir matrix possess the highest surface area per gram, and 2. The silt and especially the clay fractions are the most chemically reactive of the inorganic constituents present. Only within the last few years has the knowledge of clay mineralogy and the techniques of identifying the clay minerals reached such a stage as to enable reliable inquiry into the composition of argillaceous sediments.2,8,10,11,12,16,26 It is the purpox of this and succeeding papers to add to the fund of information on the role which these materials play in the production of petroleum from California formations by correlating their presence and associated properties with observed reservoir behavior. In the present paper attention is directed to their possible influence on damage by fresh water. OBJECTIVES The attack on this problem divides naturally into two broad phases: 1. Determination of the nature of the clays and their relationships to the other mineral components, and 2. Determination of the physico-chemical relationships between the clays and the interstitial fluids. In the work described in this paper the emphasis has been on phase 1, which stems logically from the necessity of identifying and understanding the materials to be dealt with in Phase 2. Based on the authors' present opinion that not all of the minerals which occur in oil-bearing formation are of equal importance in their effects on the flow and recovery of oil, it was decided to focus attention first upon the clay minerals content and then. later perhaps. work into the field of the normally larger size non-clay minerals and fractions. The

Jan 1, 1951

By W. C. Merrill, P. G. Nahin, A. Grenall, R. S. Crog

A progress report of an experimental investigation into the role of clay in reservoir performance is presented. The Paper gives some of the reasons for considering clay as a significant component and outlines the objectives of a broad field of stud) which it is intended to pursue. Descriptions of the analytical methods used are given; these include X-ray diffraction. elec tron miscroscopy, thin section petrography, infrared spec-troscopy, and cation exchange analysis. A suite of the more important clay minerals has been assembled and characterized l~y these methods for use as standards in core analysis. From the data obtained it appears that although no one method of analysis is diagnostic for all of the clay minerals the infrared technique shows considerable promise in this direction. For the present, one or more supplementary methods should be used to confirm the clay mineral identifications. The methods of analysis are applied to field cores taken from repesentative and widely differing strata especially as regards their susceptibility to damage by fresh water. well.; completed in the stevens and Gatchell zones in San Joaquin valley are I,articularly clear-cut examples of this behavior with stevens zone wells being more adversely affected by fresh water. cores from these zones have been studied and are discussed. It appears that differences in this behavior can be ascribed to differences in the nature of the contained clays. The value of the infrarecl spectra of the clay fractions in establishing the identity of the predominant clay minerals is given particular emphasis. INTRODUCTION It is a challenge to the technical resources of the petroleum industry that when the economic limit of production is reached, from 40 to 70 per cent of the oil in California reservoirs remains unproduced even by use of the best presently known methods of recovery. The magnitude of this abandoned volume of oil can be appreciated when it is considered that to 1950 in excess of 8 billion bbll has been produced from California reservoirs with estimated economically recoverable reserves in known fields and pools totaling nearly 4 billion bbl.24 If for every barrel of oil produced there is at least another barrel still in place, it is evident that the revenue obtained from the recovery of only a .few per cent of this volume would repay the cost of the required research manyfold. From well completion experience. production behavior, and a growing body of laboratory data it now appears certain that the mineral composition of a producing stratum has an important bearing on the productivity and ultimate yield. In addition to the organic component and water, the cores con,ist of gravel, sand. silt, and clay" in diverse variety of (a, composition and (b) texture. It is the composite effect of these two factors which is probably responsible in large measure for the way in which the oil flows to the well. The role of the clay and fine-size accessory minerals is not clear but there is a growing opinion, based on their physical and chemical properties, that it is a significant one. of particular importance are the prime facts: 1. The silt and clay fractions of the reservoir matrix possess the highest surface area per gram, and 2. The silt and especially the clay fractions are the most chemically reactive of the inorganic constituents present. Only within the last few years has the knowledge of clay mineralogy and the techniques of identifying the clay minerals reached such a stage as to enable reliable inquiry into the composition of argillaceous sediments.2,8,10,11,12,16,26 It is the purpox of this and succeeding papers to add to the fund of information on the role which these materials play in the production of petroleum from California formations by correlating their presence and associated properties with observed reservoir behavior. In the present paper attention is directed to their possible influence on damage by fresh water. OBJECTIVES The attack on this problem divides naturally into two broad phases: 1. Determination of the nature of the clays and their relationships to the other mineral components, and 2. Determination of the physico-chemical relationships between the clays and the interstitial fluids. In the work described in this paper the emphasis has been on phase 1, which stems logically from the necessity of identifying and understanding the materials to be dealt with in Phase 2. Based on the authors' present opinion that not all of the minerals which occur in oil-bearing formation are of equal importance in their effects on the flow and recovery of oil, it was decided to focus attention first upon the clay minerals content and then. later perhaps. work into the field of the normally larger size non-clay minerals and fractions. The

Jan 1, 1951

By AIME AIME

THE Institute of Metals held a well rounded out symposium on the working of metals, distributed over two sessions. At the first session* four papers were presented, two dealing with the, cold working of metals and alloys and two with the hot working of non-ferrous alloys. The first paper by E. V. Crane, dealt with "Metal Working in Power Presses." Mr. Crane pointed out the empirical nature of engineering data available for use in calculating the probable stresses developed and power requirements, for the shearing, drawing, binding and other forming operations. He described the various operations, methods of determining stresses developed and presented data obtained. In the discussion C. F. Hammond took exception to Mr. Crane's objections to the rather too frequent. annealing operations in drawing of cartridge cases, pointing out that the material was-manufactured to meet specified structure and physical requirements, which could only be met by carefully controlled sequences of working and intermediate annealing operations.

Jan 1, 1931

By J. J. Predali, J. M. Cases

J. J. Predali and J. M. Cases (Attachè de Recherche and Charge de Recherche, respectively, Centre de Recherches sur la Valorisation des Minerais, Institut Polytechnique de Nancy, Nancy, France)-The role of CO, in carbonate flotation is one of the parameters of a complex phenomenon: the adsorption of salts of fatty acids onto minerals. The authors therefore must be congratulated for their work. Their experimental results suggest some questions: 1) Recovery with C02, benzoic acid, or HCl, look very similar [(Fig. 1)] to that with the use of air; however, the recovery decreases very slightly (<10%). But in these two kinds of experiments, two parameters are different: the pH which is near 5.8 (with C02) becomes 9.1(without C02) and the concentration of Ca* I x 10-3 mole per 1 (without C02) becomes 1.9 X 10&apos; mole per 1 (without COO. 2) Adsorption experiments (Fig. 2) permit computing the surface coverage 9 which is 7.4% (without C02) and 8% (without CO_.) for an initial concentration of 12 X 10-6 mole per 1 in sodium oleate. It seems doubtful to us that this small variation can produce large increases of the recovery in flotation. 3) It is difficult to correlate adsoption and flotation experiments because they do not seem to have been done with the same size of particles. The concentration needed to obtain 95% recovery (Fig. 1) is about 3.0 X 10_" mole per l, that is, 1.13 X 10-6 mole for about

Jan 1, 1973

By J. W. Byrkit

Design features and operating methods at the new Ajo smelter are described in detail. Successful operation of a novel method of handling and charging wet concentrates to a deep bath type reverberatory furnace contribute to the daily production of 200 tons of anodes with good results from the standpoint of both metallurgy and economy. THE New Cornelia Branch of the Phelps Dodge Corp. is located at Ajo, Ariz. Large scale mining operations were started at Ajo in 1917, when a 5000 ton leaching plant was put in service to treat the copper carbonate ore that overlaid the sulphide ore-body. In 1924 a 5000 ton flotation plant was built to treat the sulphide ore and the leaching operation was abandoned a few years later. Changes in practice and additions to plant facilities have resulted in a gradual increase in the milling rate which now approaches 30,000 tons daily. Prior to the erection of the Ajo smelter, flotation concentrate was shipped by rail to Douglas, Ariz, where it was treated in the Phelps Dodge smelter. Construction of a one reverberatory furnace smelter to produce an average of about 200 tons per day of copper anodes at Ajo was started early in 1949. Initial heating of the reverberatory furnace was begun on June 21, 1950. Charging the furnace was started on july 8, and the first anodes were cast on July 14. Neither the anode furnace nor the reverberatory furnace has cooled since the initial firing. Fig. 1 is a photograph of the new smelter. Built primarily to eliminate the &apos;300 mile haul of concentrate to the Douglas plant, the new smelter was designed to treat the Ajo concentrate, with a minimum of capital investment. A novel, and relatively simple, method of concentrate handling and furnace charging made unnecessary the installation and operation of expensive storage facilities and reclaiming equipment, and obviated the necessity of holding in storage large quantities of copper-bearing materials. (Patents are pending in the United States and abroad on the Ajo process.) In the selection and arrangement of equipment, consideration was given to the full utilization of all smelting facilities, reducing the amount of idle equipment to a minimum. The layout of the smelter is shown in Fig. 2. The important problem of internal transportation was minimized by arranging the reverberatory furnace, converters, and anode furnace in a compact group and providing storage bins inside the smelter building, within reach of overhead cranes, for fluxing materials and other supplies needed in the daily operation. This can be seen in the sectional view of the smelter given in Fig. 3. Incorporated in the design were many innovations in smelting equipment intended to facilitate operations and effect economies in maintenance expense and manpower requirements. Table I gives operating data of the entire plant. Metallurgy The metallurgical practice at Ajo is based essentially upon the use of a single, deep bath reverberatory furnace for smelting wet concentrate, without concentrate storage facilities. The large reservoir of slag and matte maintained in the furnace serves to equalize, to some extent, the day to day variations in the nature and grade of concentrate and permits

Jan 1, 1954

[ ]

Jan 12, 1959

By S. A Weigand, J. W. Bolton

Production of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical. Review of Literature Carpenter and Edwards1 state that when gun metal is melted the alloy dissolves gas, the amount increasing with rise in temperature and duration of the melting. The solubility of the gas diminishes during the fall in temperature and it escapes through the liquid metal. At the moment of incipient solidification there is an evolution of gas. Sperry2 says that by using charcoal a reducing atmosphere is supplied whereby oxidation is prevented, and this also prevents gases from coming in contact with the metal. Logan3 says that many of the troubles that occur in non-ferrous castings are the direct result of one thing—oxidized material. He mentions how readily copper absorbs oxygen when molten, but does not mention the harmful effects of reducing conditions as observed in overpoled copper. Guillemin and Delachana14 investigated the gases occluded in bronze and found that the better bronzes contained mostly hydrogen while the poorer ones had a larger proportion of carbon monoxide and carbon dioxide.

Jan 1, 1929