Search Documents

By H. N. Treaftis, J. W. Cahn

THE previous determinations of the solvus of tin in solid lead disagree with one another by as much as 40°C or almost 10 at. pct. Even determinations that appear to be careful differ considerably in both the solubility and its temperature coefficient. Recent kinetic workl -3 on the rate of precipitation of tin from lead-tin alloys and thermodynamic work4 on the heat of solution of tin in lead have given some insight into the time necessary to reach equilibrium in this system. As this time is longer than that used in almost all previous determinations of the solvus, these determinations are questionable. Since the interpretation of recent kinetic results requires accurate values of the equilibrium solubility the present work was undertaken. DISCUSSION OF PREVIOUS RESULTS The methods used in previous studies may be placed into three classes: 1) Several alloys covering a range of compositions are allowed to reach "equilibrium" at a certain temperature.5-7 Some property, such as the X-ray lattice parameter of the lead-rich phase or the re- sistivity of the alloy, is then measured as a function of composition. The solubility limit for that temperature is taken to be that composition at which a discontinuity in the property occurs. However, the recent kinetic work has shown that tin precipitates in two stages. The first stage is rapid but leaves the lead still supersaturated. The second stage is very slow, and it seems from the equilibration times quoted by the investigators of the solvus that the end of the first stage of precipitation was usually mistaken for equilibrium. This is especially true at temperatures below 100°C where the first reaction is still quite rapid (from minutes to months), but where the second stage is so slow that very long holding times are required to reach equilibrium. Alternatively micrographic work8 on several alloys of different compositions seems to have given good results if done carefully. 2) The beginning of precipitation in a homogenized alloy is measured as it cools slowly8-10. Since reactions in solids undercool easily, such determinations will always give too low a temperature for the solvus. 3) Some property of an alloy is measured as a function of temperature while the alloy is above the solvus.5,9,11 The range of temperature can usually be extended slightly into the two phase region. Then the alloy is precipitated at a much lower temperature and slowly reheated. The solvus is taken to be the lowest temperature where the property of the reheated alloy is equal to that previously determined for the homogeneous alloy. Usually one also expects a discontinuity at the solvus in the temperature variation of the property for the reheated alloy. The difficulty in this method is the sluggishness of the dissolution process, and this method may give too high a solvus temperature. EXPERIMENTAL The phase boundary or solvus temperature was determined by a modification of method 3 for a series of chemically analyzed high-purity alloys, ranging from 5.1 to 26.4 at. pct Sn. The resistance, as a function of temperature, of a sample of homogenized alloy (which could easily be undercooled) was compared with the equilibrium resistance which that alloy sample attained after precipitation at room temperature followed by long isothermal anneals at various temperatures. Before each anneal the sample was rehomogenized and reprecipitated. The solvus temperature could be located to within 1°C as the intersection of the resistance vs temperature curves for the homogenized and equilibrium alloys. No attempt was made to locate the phase boundary more accurately since the limiting factor was the precision with which the alloys could be analyzed. This precision was ±0.1 wt pct Sn and corresponds to an error of 1 deg in temperature. This use of isothermal anneals differs from some of the previous investigations in which method 3 was used with baths of slowly rising temperatures. It was found early in the investigation that solvus temperatures tended to be high if the latter method was used even at extremely slow heating rates. For example a

Jan 1, 1961

By C. M. Young

The safety lamp is the most common and convenient apparatus for detecting inflammable gases in mines, the presence of gas being shown by a blue flame, called the cap, if the wick has been lowered to suppress the luminous flame. The height of the cap increases with the proportion of gas and with the temperature of the lamp flame. Lamps of the Wolf type, the fuel of which is benzine, have a hotter flame than lamps in which vegetable oils are used, such as the Davy, and the Clanny, and are more sensitive than the latter and their many modifications. The Piehler alcohol lamp gives a still higher cap while the Clowes hydrogen lamp is most sensitive of all. While the effect of the temperature of the source of ignition is well known, the writer knows of no previous attempt to correlate the change of this temperature with change of the height of the cap produced, In order to determine the height of the cap at various temperatures, it was necessary to have a source of ignition the temperature of which could be accurately controlled over a considerable range. This condition was met by a coil of wire of high fusing point heated by an electric current controlled by a variable resistance. The use of a coil offered the further advantage of freedom from complications due to the flame of a burning fuel. Such a flame, being itself of variable height, would to some extent raise or lower the elevation of the base of the cap and therefore add to the difficulty of determining the height of the cap. Besides this, the presence of a small cap from the lamp fuel, commonly known as the "fuel cap," would interfere with the observation of small gas caps. After some experiment, a coil was made of platinum wire, No. 26, diameter 0.016 in. The coil was 17/64 in. (6.746 mm.) in outside diameter and had eight full turns in a length of 1/2 in. (12.69 mm.). This was connected to an electric circuit through an adjustable resistance, as shown in Fig. 1. In order to measure the temperature, a thermocouple was inserted in the center of the coil; the leads passed out at the ends and were ccnducted to a millivoltmeter. It is probable that the current of air passing upward through the coil resulted in the indication of a tempera-

Jan 1, 1920

By Lucien Eaton

VENTILATION in the iron mines of the Lake Superior region in nearly all cases is natural; that is, it is induced by the difference in elevation between different outlets in the mine and by the difference in temperature of the air in the mine and that outside. This difference in temperature is frequently augmented by placing a steampipe in the upcast shaft; but aside from this, artificial aids to ventilation have been rare until - recent years. In some of the older mines, as at the Cliffs Shaft mine at Ishpeming, Mich., in the 80's, fans have been used when there was only one opening to surface, but their use was abandoned as soon as a natural circulation of air started. In recent years, the Newport mine at Ironwood, Mich., was the first to use positive mechanical ventilation. The installation was not large enough, however, to give definite results, reliance being placed largely on natural ventilation. With the coming of warm weather in the spring of 1914, the necessity of positive mechanical ventilation at the Lake mine of the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., became evident. The workings of the Lake mine are under the bed of old Lake Angeline, which was pumped out in 1894, and the mine had been in operation for 6 years prior to that date making a total of 26 years of continuous operation. The total production, up to 1914, amounted to over 8,000,000 tons. The ore was first mined by square-set rooms and pillars, but this was later changed to top slicing and caving. Both methods required the use of large amounts of timber, probably 80,000,000 board feet in all, practically all of which remained in the timber mat. The slow oxidation of this timber was one of the principal causes leading to the installation of mechanical ventilation. The mine was served by only one working shaft, called No. 4, a second outlet being provided by a raise to the surface from the old workings on the south side of the mine. This raise was the "down cast;" but it was very small and the drifts and raises leading to it were too small and crooked to permit an adequate amount of air to enter the mine, especially during the warmer weather. Measure-

Jan 8, 1920

By S. F. Emmons

The history of the mining region of Custer county has been somewhat peculiar. Although, in the broader features of geological structure, it bears a strong resemblance to its newer and now more famous neighbor, 40 miles to the northward, the Cripple Creek mining district, it has been noted for failures rather than for successful mining ventures. Yet it has a number of mines that have proved themselves to be remarkably rich, and many others that have well-defined veins and very rich ore, though they never have been worked to any great depth. A few of the deposits seemed to the early miner so anomalous in form and manner of occurrence that they were popularly described as " contrary to all geological laws." The region has had several " booms," succeeded by more than usually violent reactions, the latter having proved more permanent than the former. It was, for a long time, the favorite resort of patent-process mongers, and the ground is now strewn with relics of various unsuccessful reduction-plants. Mismanagement, ignorance and disagreements among mine-owners seem to have been quite as responsible for the want of success in the region as the quality of the ores or the form of the deposits. In the early eighties, when the booms had not entirely died out, a division, then under my charge, of the U. S. Geological Survey, undertook an examination of the region for the purpose of making a study of its ore-deposits. The areal survey was carried to completion by Mr. Whitman Cross, but the study of the mines could never be completed for the reason that most of them were closed, for one reason or another, before we had time to visit them. From time to time, one or another of the important mines has been started up again, but it was not

Jan 1, 1897

By T. G. Madgwick, A. Beeby Thompson

FoR more than 2500 years, natural gas issues in the Surakhany district of the Apsheron peninsula were the object of pilgrimages by fire worshippere and Hindoos from Burma and India. Even as late as 1890, Hindoo priests conducted ceremonies in a temple at Surakhany, which probably replaced a more ancient one; but later, the visits of the pilgrims were prohibited in order to check the spread of Asiatic diseases in that region. For centuries, limited supplies of oil have been abstracted from shallow excavations in the Caspian oil belt and dispatched into the interior of Asia and elsewhere for medicinal and industrial purposes. Statistics show a yield of 37,400 bbl. in 1863, but only since 1869 has there been serious development; in that year the yield was 203,000 bbl. At that time, hand digging was supplanted by drilling, and the enormous wells that resulted from tapping sources hitherto beyond the reach of operators completely demoralized the industry for a time, owing to inadequate outlets for the products. The early activities in this area were greatly hindered by annoying taxation, monopolies, imperial land grants, etc., but when these were revoked or adjusted, in 1877, the industry sprang into prominence and, between 1898 and 1901, the Baku fields produced practically one-half of the world's supply of oil. Within a few miles of Baku lie the two richest oil fields in the world; viz., the Balakhany-Saboontchy-Romany and the Bibi-Eibat, the latter constituting almost a suburb of the city. For many years the gasoline obtained in the refineries of the Baku area was burned in pits, being considered an undesirable product, and until 1870 the residue also was destroyed, its value as a fuel not being recognized. Kerosene was the main product sought by the refiners. It was shipped across the Caspian Sea and up the Volga to the industrial centers of Russia. Only on the completion of the Baku-Batoum railway did the Baku oil fields secure important commercial communication with the outside world through the medium of the Black Sea. The first tank steamer was successfully launched on the Caspian in 1879, by Messrs. Nobels, for transporting oil in bulk instead of in barrels. In 1905, an 8-in. pipe line to Batoum was completed; this was capable of transporting to seaboard 8,000,000 bbl. of kerosene per annum.

Jan 1, 1921

By D. A. J. Swinkels

The problem of determining oxygen levels in liquid steel to aid in deoxidation control has received general attention for a number of years. Work in this direction started at the B.H.P. Central Research Laboratories early in 1967 with an evaluation of sampling techniques followed by vacuum fusion analysis to determine the oxygen content of the samples (1). It was found that these techniques had a number of drawbacks if they were to be used for deoxidation control. The method of analysis was rather too slow to allow effective control and measured total oxygen level rather than dissolved oxygen. Furthermore, the results were found to be very variable due to slag entrainment in the samples. Attention therefore turned to the galvanic cell method using a solid oxygen ion conductive electrolyte such as cubic stabilised zirconia. The ionic conductivity properties of electrolytes such as (ZrO2) 85 (CaO).15 had been studied by a number of investigators and had already been applied to the measurement of oxygen activity in gases, in lower melting metals such as copper, lead, tin, silver, alkali metals and indeed the first studies in steel had been made (2,3). Since then the results of a number of studies in the development of an expendable oxygen probe for steel have been reported (4-9).

Jan 1, 1972

By Theodore Simons

I. INTRODUCTION PERMISSION to present this paper at the February, 1915, meeting of the Montana Section of the American Institute of Mining Engineers was liberally granted by W. A. Clark, Jr., President and General Manager of the Timber Butte Milling Co., and by the representative of the Minerals Separation Co. For the many courtesies shown the writer on his visits to the mill and for information supplied, he is indebted to all the officers of these companies, especially to W. N. Rossberg, W. D. Mangam, Hamilton Cooke, Jr., T. M. Owen, T. C. Wilson, R. McGillivary, L. L. Quigley, C. Bartzen and others. The writer takes this opportunity to herewith express to them his appreciation and sincere thanks.

Jan 6, 1915

By W. L. Grose, J. E. Nealy

A device developed by the U.S. Bureau of Mines for the detection and quenching of coal mine explosions suffers from the inability to discriminate between the light emitted from hydrocarbon combustion and that emitted by electrical sparks and miner's cap lamps1. Since the quenchant device is activated by an internal explosive charge, the possibility of serious injury to nearby personnel demands a detector which can reject false signals. Described herein is a detector which can provide a rapid response signal upon the emission of radiation from hydrocarbon combustion and concurrently reject spurious signals from such sources as sparks and cap lamps. It was suggested that a detector might be developed to operate on the principle of monitoring the radiation intensity emitted from two separate spectral regions and ratioing the intensities2. A series of experiments was conducted for combustion of methane-air mixtures which demonstrate the ability of such a detector to discriminate between combustion and spurious signals. Experimental Apparatus A cylindrical (3.8 in. diam by 12 in.) stainless-steel shock tube test section was used as a combustion chamber. The test section was equipped with quartz windows (2 in. diam) on either side, a piezoelectric pressure transducer, and two steel electrodes. A 10-kv capacitor discharged across the electrodes provided a submicrosecond duration spark to ignite the gas mixture within. The desired partial pressures of methane and air were obtained by using a Wallace and Tiernan 0-800 mm Hg pressure gauge with which pressures could be determined to an accuracy of % mm Hg. All tests were conducted with a total pressure of 1 atm in the chamber. To

Jan 1, 1972

By G. M. Crosby

Seven mines with important production records in the Coeur d'Alene lie adjacent to the Gem stocks —the Frisco (Gem), Hercules, Interstate, Rex (Sixteen to One), Success (Granite), Sunset, and Tamarack. Old records are incomplete, but available data given in Table I show these mines have produced 10.550,721 tons of ore containing more than 50 million oz of silver, more than 1.5 billion lb of lead, and about 1 billion lb of zinc (approximately 1.25 million tons of lead and zinc combined). Average ore grade is 4.8 oz of silver per ton, 7.2 pct Pb, and 4.6 pct Zn. This impressive production represents about 12 pct of the District's yield. At present metal prices, with modern beneficiation, the gross value would be more than $400 million. THE GEM STOCKS The Gem stocks, considered to be outliers of the Idaho batholith of Late Cretaceous age, are located in the northern half of the Mullan quadrangle, and extend from the town of Gem, Idaho, along a strike of N30°E for a distance of approximately five miles. They occur as two major masses of monzonitic rocks commonly referred to as the North stock, which covers an area of 1.1 sq miles, and the South stock, which covers 2.6 sq miles. The areal pattern is roughly club-shaped, the North stock representing the handle and the South stock the head of the club. Two and a half miles west and five miles northeast are two groups of smaller stocks, isolated from the main masses but of the same general rock type. This discussion is limited for the most part to the North and South stocks. At the north end, where the intrusion is about 3200 ft wide, the walls are about parallel and dip very steeply west. At the south end, where the mass is about 7000 ft wide at surface, the walls dip away from each other at moderately steep angles. An aeromagnetic survey' detects and outlines with surprising accuracy the two main stocks. as illustrated on the magnetic contour map (Fig. 2). Of particular interest is the location and shape of the magnetic anomaly representing the South stock. The anomaly is centered over the south end of the outcrop, and a westerly extension joins it with a smaller anomaly over the Dago Peak stocks. The latter anomaly, likewise, is located over the south end of the isolated stocks. This pattern suggests the intrusion has greater extent at depth to the south and west. Though correlation between the Dago Peak stocks and the larger masses is suggested, the controversial aspects of the Dobson Pass fault, which separates the two areas, casts doubt on a correlation. Topographically the monzonite stocks are ignored by the drainage pattern indicating these rocks, and the invaded rocks of the Lower Belt Series react similarly to erosion. The drainage patterns of Nine Mile and Canyon creeks cut indiscriminately across the monzonite-Belt contact, resulting in both valleys and ridges in the southern end of the intrusion. Nine Mile Creek traverses diagonally the entire five-mile length of the stocks. The monzonite rocks of the intrusion are referred to locally as granite, but granite is rare and the rocks comprise a wide variety of types. Their characteristics, described in detail by F. L. Ransome and F. C. Calkins,' are summarized by P. J. Shenon.' The principal rock type is coarse-grained, light gray, porphoritic monzonite containing black crystals of hornblende. Pyroxene, epidote, and titanite

Jan 1, 1960

By H. E. Mussey

WHEN the American Institute of Mining Engineers visited the Birmingham district in May, 1888, the four Ensley furnaces (Fig. 1) then FIG. 1.-BLAST-FURNACE DEVELOPMENT IN ALABAMA. completed were referred to as monumental.1 Their dimensions are given in Table 1. Mr. Gordon stated, with considerable satisfaction, that on the preceding day one furnace had produced 165 tons. The blast was

Jan 10, 1924

By P. Marier, T. R. lngraham

The kinetics of the sulfation of MnO,, MnzO3, and Mn3O4 in SO,, SO3, and O, mixtures was examined and the descending order of sulfation rates at temperatures near 400°C was found to be Mn,O3 > MnO, > Mn3O4. The respective activation energies for the thermal decomposition of MnO, and Mn,O, are 39 and 47 kcal. At 900°C, the thernzal decomposition of MnSO, to MnzO3 is slower than that to Mn3O4. The respective activation energies are 62 and 51 kcal, respectitely. MANGANESE is used to improve the hot workability of steel in the proportions of approximately 13.5 Ib of ferromanganese per ton of steel produced. This requirement accounts for about 95 pct of its large industrial market in North America. The remaining 5 pct is used in the battery and chemical industries. In most North American ores, the percentage of manganese and the manganese-to-iron ratio are not suitable for the direct production of ferromanganese. Hence, most of the North American requirements for manganese are satisfied by importing ore. Typically, many of the studies done on native low-grade manganese resources have been directed toward the production of ore substittes" and the recovery of manganese from open-hearth slags.3 Of the wide variety of processes which have been proposed, the most popular involve compounds in the Mn-S-O system. The thermodynamic properties of manganese and its compounds were reviewed by ah' in 1960 and, more recently, lngrahams discussed the thermodynamics of some of the reactions involved in the Mn-S-O system at normal roasting temperatures. The conditions for producing manganese sulfide during the reduction roasting of manganese sulfate are discussed by Fuller and Edlund.9 A novel scheme was proposed recently by zimmerley7 for utilizing waste sulfur dioxide from stack gases to recover the manganese from ocean-mined manganese nodules. Very little of the work published on manganese compounds has been related to reaction rates. Singleton et 1.' studied the rates of reaction on the MnO-C and Mn7C3-3MnO systems and observed linear and parabolic kinetics respectively in the systems. Tatievskaya et a1.' studied the low-temperature reduction of Mn&, MnO,, and Mn& in HZ and CO, and reported activation energies in the range 1628 kcal. In this paper, the rates of some of the decomposition and formation reactions involving MnSO4, MnOz, MnzO3, and Mn3O4 will be examined after the conditions for the thermodynamic stability of the individual compounds have been designated. CONDITIONS FOR STABILITY OF MnSO4, MnOz, MnZO3, AND Mn3O4 The areas of stability for h'hSO4, MnOz, MnzO3, and h3O4 were established from the data of Mah4 and Ingrahams and are shown in the predominance area diagram,10 logpq- logpsq, in Fig. 1. The diagram is drawn for two temperatures, 700°K, solid lines, and 1100°K, dotted lines. The sketch for the lower temperature includes the conditions likely to prevail in the Zimmerley patent7 when manganese nodules react with sulfur dioxide and that for the higher temperature indicates the conditions for recovering MnzO3 or Mn3O4 from MnSO4 during a roasting reaction. From the fact that the boundary between the areas of stability of MnOz and hSO4 at 700°K is parallel to the abscissa, it is evident that MnOz and SO2 should react together to produce MnSO4, irrespective of the oxygen pressure in the system. If the source of sulfur for sulfation were from waste flue gases, it is likely that the oxygen content of the gas stream would be more than sufficient to oxidize any MnsO4 to MnzO3, 107 atm of O2 required, or even to convert any Mnz03 to MnOz, 0.02 atm OZ required, prior to sulfation. At 1100°K, the diagram indicates that MnSO4 may be converted directly to either MnzO3 of Mn3O4, depending upon the prevailing partial pressure of oxygen. When the gas stream contains more than 1 pct Oz, logpq = -2, only MnzO3 would be recovered from an experiment done under equilibrium conditions. At oxygen partial pressures of less than 1 pct, one would expect to bring about a reversible exchange between MnSO4 and Mn3O4 by appropriate adjustment of the partial pressure of SOZ. These various reactions will be described in the subsequent kinetic experiments.

Jan 1, 1969

Book Notices CATALYSIS IN INDUSTRIAL CHEMISTRY. By G. G. Henderson. Lond. and N. Y., Longmans, Green and Co., 1919. 202 pp., cloth, 9 X 6 in., $3.25. This, the latest volume of the series of Monographs on Industrial Chemistry which is being published under the editorship of Sir Edward Thorpe, is intended to present broadly, our present knowledge of the phenomenon of which it treats. The hook reviews the existing literature on catalysis, paying particular attention to the many applications now used in industry. COMMERCIAL OILS-VEGETABLE AND ANIMAL. With special reference to Oriental Oils. By I. F. Laucks. 1st edition. N. Y., John Wiley and Sons, Inc.;, Lond. Chapman and Hall, Ltd., 1919. 138 pp., cloth, 8 X 5 in., $1.25. Intended to give to men in the oil trade, who have not had technical training, the technical data and information required in every-day dealings, in concise form. The various commercial oils are listed, together with their sources, uses, and phys-ical and chemical characteristics. The values have been collected from the standard texts, supplemented, particularly in regard to oriental oils, by the results obtained in the author's laboratory. FIFTY YEARS OF IRON AND STEEL. By Joseph G. Butler, Jr. Cleveland, The Penton Press, 1919. 145 pp., por., 10 X 6 in., leather. (Gift of author.) This volume is one of a special edition, of 100 copies, of an address delivered before the American Iron and Steel Institute in 1917, in which the author gives his personal reminiscences of the development in iron and steel making, as observed during an active participation in the industry in eastern Ohio, which began in 1857. To this are added some brief data on the early history of iron and steel, and a chapter on the activities of the American iron manufactures during the great war. The volume is profusely illustrated with portraits of men of note in the industry.

Jan 12, 1919

By D. M. James, J. C. Martin

The results are presented of a study of the application of analytical methods to the solution of two-phase flow into single wells. Approximate analytical expressions for the pressure distribution in two-phase flow are found ;;; a number of conditions. The results obtained from the analytical solutions me found to be in good agreement with results obtained by finite difference techniques using a high speed digital computer. Mathematical solutions for four sets of boundary conditions are presented. All of these solutions are composed of a short-term transient plus a steady or quasi-steady state. The rates of decay of the short-lived transients are analyzed. It is found that the durations of the short-term transients may be characterized by a parameter defined as the time constant which can be determined from simple relations. It is shown also that if the outer radius is much greater than the radius of the well. the short term transients decay at rates which are proportional to the square of the exterior radius, and the rates of decay are only slightly dependent upon the radius ratio. Numerical solutions based on finite difference techniques are presented for a number of conditions. The numerical solutions are in good agreement with the predictions based on the theoretical analysis for small and moderate drawdowns. Examples involving large drawdowns indicate that the nonlinearities in the equations of flow do not appreciably alter the longevity of the short-term transients. In all cases the time required for the short-tern transients to disappear is predicted satisfactorily. INTRODUCTION The mechanism by which oil and gas flow into a single well is of vital interest to the petroleum industry. The fundamental equations of two-phase flow which describe this mechanism are nonlinear partial differential equations. Numerical solutions of these equations describing pressure transients have been obtained with the aid of electronic computers. Although solutions obtained in this manner take into account a large number of effects, the reduction of this information to useful generalities is difficult. One method of obtaining generalities is the use of linearized approximations of the nonlinear equations. Since it is possible to obtain explicit solutions of the linearized equation, general properties of the role of pressure in the flow mechanism may be ascertained. Results obtained from this approach are limited to some extent by the linearizing assumptions. The severity of these limitations may be evaluated by comparing solutions of the linear equation with numerical solutions of the more exact nonlinear equations of two-phase flow. In the past considerable amount of work has been devoted to studying pressure build-up using the single-phase flow theory. Unfortunate1y, most prep sure build-up tests involve multiphase flow. A small amount of work has been done studying pressure build-up where the flow is two-phase. The encouraging results of these studies suggest that useful results may be found from additional studies of not only pressure build-up, but also the rapid transients associated with placing a well on production. This paper presents the basic theory of the pressure transients associated with placing a well on production and with closing it in. The paper is concerned chiefly with two-phase compressible flow; however, the results also apply to single-phase flow. The results are based on analytical solutions of the flow equations, and they are verified by numerical solutions using finite difference techniques. Much of the previous work on compressible flow into wells has been confined to single-phase flow. Some work has been done on compressible two-phase steady state flow, and solutions of the equations of flow have been found by finite difference techniques using high-speed computers. Muskat1 presents some rather general solutions to the equations of single-phase compressible flow into wells. Much work has been done on pressure build-up in wells (see, for example, Refs. 2-6). Almost all of the work on pressure build-up concerns single-phase flow with the exception of Ref. 5 and part of Ref. 2. Some work has been done on pressure fall-off in injection wells.718 Muskat9 presents the solution of the equations for radial steady state two-phase compressible flow. Handyl0 extends Muskat's solution to obtain

By Ernest R. Lilley

While American scientific literature contains much information upon geologic conditions controlling the production of oil in Rumania, copper in Chile, and other fuel and metallic resources in many foreign countries, it is singularly lacking in data about the nonmetallics outside of the United States. Thus, though the United States is the outstanding market for European high-quality refined kaolin, and for the chinaware, porcelain, and other products of the European ceramics industries, American literature contains only the briefest references to the deposits from which the raw kaolin utilized is obtained. To the writer, to whom has come in the past year the opportunity of visiting a number of these deposits personally, they have proved of extreme interest both commercially and geologically. It is the latter phase that is discussed in this paper. The older and now largely crystalline rock areas of France, Germany, and other parts of western Europe contain numerous pegmatite dikes of which the upper portions have been subjected to surface weathering and kaolinization in much the same way as those of the eastern portion of the United States. Like the latter, the European pegmatite kaolins have long been known for their freedom from iron and other impurities offensive to the china and porcelain manufacturer. Unfortunately, they are also, like the American deposits, individually of small size and noted for their high costs of production. Deposits of sedimentary clay similar in many respects to the high-quality sedimentary kaolins of Georgia and South Carolina are known and worked, notably in southern Germany and in the Newton Abbott district of Devon and Dorset in England. In general, their relationship to the parent rock from which they were derived is more evident than in the United States and the individual deposits are of smaller areal extent and less regular in outline. While these deposits are of considerable economic importance they did not, because of their similarity to deposits in America, attract and hold the interest of the writer to the extent that several other types of deposits did. It is to the latter, which are so different from the kaolin

Jan 1, 1932

By John D. Price

R. W. Campbell (Jones and Laughlin Steel Carp., Pittsburgh)—As usual John Price has presented an excellent paper. I know of no one who has devoted more time and conscientious thought to this subject than he has, and his efforts have produced scientific data and conclusions of real value. Results of similar studies made by the Jones and Laughlin Steel Corp. on the blending of Pennsylvania coals may be of interest. During 1935 the late F. W. Wagner and the present writer developed an empirical physical fuel value formula for evaluating the combined physical tests of metallurgical coke, see Table IV. In the development of the formula, the tumbler test, shatter test, screen test, and porosity of coke have been taken into consideration. Each of these tests brings out some physical property not expressed by the others, and in estimation of the importance of these tests as a medium for evaluating coke for the blast furnace, their worth has been graded as follows: It was thought that some additional penalty should be applied to cokes that do not show a uniform screen size, assuming that coke larger than 4 in. was not desirable and that this size was an indication of irregular size. Therefore the screen test factor is further corrected by applying a penalty of 1 pct for each 1 pct material greater than 4-in. size as shown by the screen test. The physical fitness of coke for blast furnace use depends upon four fundamental characteristics: l—gen-era1 strength, as indicated by the shatter test; 2— abradability, or the resistance of cell walls to reduction in size by attrition, as indicated by the tumbler test; 3—porosity; and 4—size and uniformity. Each of these characteristics is not of equal importance, but surely, in an attempt to determine an accurate physical value, the individual value of each should be taken into consideration. The formula is used as a yardstick, so to speak, in determining variations in the normal production of metallurgical coke and in making comparisons between normal coke and experimental blends with other coals. Table IV gives results of coking tests on raw and washed high volatile coals and these same coals with blends of coke breeze, anthracite coal, char and low volatile coals, all from Pennsylvania. The table also gives the source of the coals and coke breeze, as well as their proximate analyses. It will be noted that the washing of the raw high volatile coal increased the physical fuel value from 26.17 to 39.16, showing the effect of removing shale and slate which produces a detrimental fracturing and weakening of the coke. It is a well known fact that many Pennsylvania high volatile coals contain an excess of resinous material or binder which has a tendency to weaken the coke, owing to its high evolution of gases during carbonization. Tests were therefore made with coke breeze, an inert material, in an attempt to alleviate this condition. Blends of washed coal with 5 pct and 7.5 pct coke breeze collected from the coke plant quenching sump (82.9 pct through 1/8-in. screen) resulted in cokes with a physical fuel value of 20.75 and 16.73 respectively, lower than results obtained from 100 pct raw high volatile coal. It will be noted that the percentage of + 4-in. coke increased but that the tumbler test was very low. Undoubtedly better results could have been obtained if the coke breeze could have been crushed extremely fine. During World War II the government asked the coking industry to consider the use of anthracite coal as a substitute for high quality low volatile coal, which was extremely scarce at the time. The next series of tests was made with blends of raw and washed high volatile coals and 5, 10, and 15 pct Pennsylvania No. 5 buckwheat anthracite (100 pct through l/8-in. screen). It was necessary to use some raw high volatile coal in these blends because of insufficient washer capacity at the time. It will be noted that the physical fuel values

Jan 1, 1954

By J. B. Dilworth

The purpose of this paper is, first, to give a general account of a little-known coal-district of SE. Kentucky, its topography, drainage, and mineral resourcee, for those who may be interested in its economic development; and secondly, so to describe the geologic features of the field as to furnish available data to those engaged on the broader problems of Appalachian coal-geology. The data from which the major portion of the paper has been prepared were obtained, in professional investigations for private individuals and corporations, within the last decade. The area under review, defined by a heavy line on the map, Fig. 1, lies between Little Black and Pine mountains, and extends from Harlan on the west to a N-S. line crossing Looney creek 3 miles from its mouth on the east. This area can be divided for description into a Western and an Eastern Division. The character of investigatioil pursued in the Western Division, below Fugitt creek, was very different from that employed in the Eastern. In the former, only a rapid reconnois-sance was attempted: such coal-openings as had been made by prospectors or by citizens in obtaining fuel were visited, their

Jan 1, 1913

By Robert Glass Cleland

[Incorporated under the laws of the State of New York OFFICE, 41) WALL STREET, NEW YORK 5, N. Y. Authorized4,000,000 shares $150,000,000.00 Outstanding-5,071,260 shares 126,781,500.00]

Jan 1, 1952

By Waldemar Lindgren

Introduction To the miner, as well as to the geologist, the eastern part of Cuba is a most interesting region. Here we find, in contrast to the moderate relief predominating elsewhere in the island, an imposing mountain range, the Sierra Maestra, extending east and west parallel to the coast, its precipitous front facing the blue Caribbean Sea.. In a geological sense this range is largely an unknown land, the only well-explored region being that in the vicinity of Santiago. The range also contains the most important mineral deposits of the island. They comprise, first, a series of iron deposits yielding a partly hematitized magnetite with low content of phosphorus; second, a remarkable copper-bearing vein at El Cobre; and third, various manganese deposits. Probably more deposits will be found, for the larger and western part of the range is as yet little explored and its slopes are covered by a thick tropical jungle. The following notes are based on a short visit by the senior author in January and February of 1914 to the mines at Daiquiri, El Cobre, and Mayari. For many courtesies and great assistance he is deeply obliged to Charles F. Rand, President of the Spanish-American Iron Co.; to George W. Pfeiffer, General Manager, and to the several members of his staff.

Jan 10, 1915

By Theodore Simons

Permission to present this paper at the February, 1915, meeting of the Montana Section of the American Institute of Mining Engineers was liberally granted by W. A. Clark, Jr., President-and General Manager of the Timber Butte Milling Co., and by the representative of the Minerals Separation Co. For the many courtesies shown the writer on his visits to the mill and for information supplied, he is indebted to all the officers of these companies, especially to W. N. Rossberg, W. D. Mangam, Hamilton Cooke, Jr., T. M. Owen, T. C. Wilson, R. McGillivary, L. L. Quigley, C. Bartzen and others. The writer takes this opportunity to herewith express to them his appreciation and sincere thanks. Location of Mine and Mill The concentrator of the Timber Butte Milling Co. was built to treat the ore mined at the Elm Orlu mine of the Elm Orlu Mining Co., which carries zinc and lead in sphalerite and galena; copper in bornite, chal-cocite, tennantite, and tetrahedrite; and gold and silver either free or chemically combined with the sulphides of the base metals. The gangue is chiefly quartz, barite, fluorite, rhodonite, and rhodocrosite. The iron in the ore occurs as irqn pyrites. The Elm Orlu mine is situated in Butte, Silver Bow County, Mont., near the northern border of what is locally known as the Butte sulphide-copper belt, about one mile north of the Anaconda mine, and adjoining the Black Rock zinc mine of the Butte & Superior Co. on the southwest. The mill is on the northern slope of Timber Butte, a prominent topographical landmark in the Butte district. This site permits to a large extent the gravity system of ore flow; it presents a convenient and extensive area for a tailings pond; and it is comparatively near to the source of water supply and to existing railroads.

Jan 1, 1916

By E. De Goyler

Volcanic origin was among the first of the theories advanced to account for the occurrence of the salt domes of the Gulf coastal plain, northern Louisiana, and eastern Texas, and it is still being re-stated in various forms by the most recent contributors to our knowledge of the geology of such deposits. Argument has been largely by analogy and attention has repeatedly been called to the Mexican oil fields, particularly those of the Tampico-Tuxpam region, because of the occurrence of oil in close proximity to volcanic plugs in those fields, an occurrence supposed to have some resemblance to the common occurrence of oil in the salt domes of the United States. The author, having spent several months of the past year in a general study of salt domes and in a detailed study of certain domes in the United States, and having been acquainted for some time with the exploration of similar domes in the Isthmus of Tehuantepec region, Mexico, and with the general geology of the Tampico-Tuxpam region, Mexico, has reviewed the various theories of volcanic origin for salt domes which have been advanced to the present time. The purpose of this paper is to present such review and to discuss the supposed Mexican analogy. Review of Volcanic Theory R. Thomassyl who had visited the Five Islands of Louisiana between 1857 and 1859, in 1860 described them with some care, noting their distinct character, alignment, and similarity, and ascribing to them a volcanic origin. He regarded them as being akin to the mud lumps in the delta of the Mississippi and was impressed by their symmetry and by the ponds or lakes which occur on several of the islands and which he regarded

Jan 1, 1920