Search Documents

By J. C. Judd

The U.S. Department of the Interior, Bureau of Mines investigated solvent extraction methods for recovering gallium from filtrates produced from sulfuric acid leaching of hydrometallurgical zinc residues. These filtrates typically had pH values of 0 to 0.5, too high an acid content for effective gallium recovery by traditional extractants. Of the nine extractants studied in batch tests, 0.3M octyl phenyl acid phosphate (OPAP) in a kerosene diluent was the most effective extractant for gallium recovery, extracting up to 99.9 pct of the gallium. This high extraction was possible when the iron in solution was maintained in the reduced ferrous state. Batch tests also showed that a 1.5M-H2SO4 strip liquor recovered 98 pct of the gallium from the loaded OPAP. A continuous solvent extraction system was designed and operated based on McCabe-Thiele analyses of equilibrium loading and stripping isotherms. When 12 L of leach filtrate containing 0.32 giL Ga and 20 giL Fe were pumped through the system in 32 hr, results showed that 95 pct of the gallium was extracted in four stages at an A:O ratio of 1:1. Stripping the loaded solvent with a 1.5M-H2S04 liquor recovered 94 pct of the gallium in four stages at an A:O ratio of 1:4. A two-stage, 50-pct-phosphoric acid strip successfully removed ferric iron from the OPAP, allowing high gallium extractions to be maintained.

Jan 1, 1990

By D. Su

This paper presents the details and results of a preliminary investigation into the response of borehole pressure cells (BPCs) in soft coal. Two parallel approaches, laboratory calibration and nonlinear finite element simulation, were adopted for deter- mining the BPC K-factor, which was defined as the ratio of cell pressure change to the corresponding change in external pressure. Results from both the laboratory calibration and the nonlinear finite element simulation revealed a nonlinear response of cell internal fluid pressure to external loading. The K-fact& also is shown to increase with increasing setting pressure and decreasing medium modulus. -Depending on the setting pressure, the K-factor for coal having a Young's modulus of 1.6 x lo5 psi ranges from nearly 1.2 at 2,000 psi of external pressure to 1.485 at 8,400 psi of external pressure. The improved under- standing of BPC behavior leads to the more accurate calculation of BPC K-factor in coal which significantly improves the correlation between pillar pressures measured in underground coal mines and those predicted by nonlinear finite element simulations of these pillars.

Jan 1, 1990

Gold at Renco occurs in association with pyrite, pyrrhotite, chalcopyrite and quartz and is confined to a series of brittle fractures and fault breccias (reefs) preferentially developed within an anastomosing ductile shear zone. During late Archaean crustal movements both the orebody and the enclosing host rocks were deformed within a series of east-north-east striking, southerly dipping, shear zones. The reefs within these shear zones are now texturally different to those away from the shear zones, and this difference is reflected by differences in the way the gold is distributed in the two reef types. These differences are not taken irto account by the software package currently being used to generate kriged plans of gold grade and reef thickness and this may explain some of the inaccuracies found in these plans.

Jan 1, 1990

Project cost control procedures and computer systems have enjoyed a successful and simple relationship over the past decade, thanks primarily to the proliferation of portable computers or PC's. Prior to the introduction of this technology, project control was largely a manual and somewhat onerous task of historical data compilations, with little time available for dynamic forecasting, staged planning, or pre-emptive cost control. Automated systems developed during this era were resident on "Heavy Iron" or mainframe computers and were expensive to maintain and operate. Use of these early systems was limited to large engineering, construction, and industrial concerns with the economies of scale and funding required for their successful application. Systems were either designed for critical path analysis or task scheduling, but rarely integrated with the other, much less cost control.

Jan 1, 1990

By R. W. Luhning, S. D. Gittins, J .. A. Haston

"The Underground Test Facility (UTF) project operated by the Alberta Oil Sands Technology and Research Authority (AOSTRA) north of Fort McMurray has achieved marked success in field testing mining access and horizontal well in situ recovery of bitumen from the Athabasca oil sands.Mine access has provided for effective placing and operation of horizontal wells in the oil sands from a tunnel system in the underlying limestone. Performance of the in situ recovery process, Steam Assisted Gravity Drainage, has substantially exceeded forecasts made at the start of the project. Over-all results of the program to date show great promise for horizontal well in situ technology as a competitive source of bitumen from Alberta's vast oil sands deposits. The potential economics of a commercial expansion at the site are reviewed in this paper.IntroductionIn situ recovery o f bitumen from the Athabasca oil sands has puzzled the oil industry for many year s, but a breakthrough appears close at hand. The Underground Test Facility (UTF) project initiated by the Alberta Oil Sands Technology and Research Authority (AOSTRA) has had notable success in the piloting of horizontal well processes, which offer prospects for commercial development even under the highly competitive situation facing the Canadian industry . This paper describes the project briefly and presents the potential economics of commercial development on the UTF lease."

Jan 1, 1990

By Robert L. Akright

The Sumich (Victorine) gold mine is located in the Toiyabe Mountain Range on the east side of Victorine Canyon, a north-trending branch off Kingston Canyon in the northwest quarter of Section 27 and southwest quarter of Section 22, T16N, R43E, in the southern end of Lander County, Nevada (Fig. 1). HISTORY Discovered in 1862, the Victorine reached a peak of development between 1872 and 1887. The "Victorine" and "Morning Star" lode mining claims, located on the outcrop of a prominent auriferous quartz vein, were patented in 1869 and 1891, respectively. 1, respectively. Gold ore was mined underground in adits driven, on the level, directly into the side of the mountain. Ore brought to the surface was trammed about 457 m (1500 ft) south on a track constructed along the contour to ore bins. From this transfer point, the ore was moved by aerial tram to the bottom of the canyon then hauled by horse-drawn wagon to the mill located about 3.2 km (2 miles) east down Kingston Canyon. Exact details of the milling process used on the Victorine are lacking, but old reports mention water-driven stamp mills, amalgamation, chlorination, and cyanidation. Gold and silver mill products are reported to have been sent to England for final refining. High-grade gold values of 103 g/t (3 oz per ton) remaining in mine walls and on outcrops, attest to the lack of success in treating the Victorine ore in the early mills. The Victorine mine may have been worked sporadically after 1887 with little success. In 1934, control of the property was acquired by William P. Moloney, an attorney from Marion, OH, who also control- 1 led an interest in the successful Goldacres mine in Lander County, NV. This property was studied, sampled, and metallurgical tests were done in 1934, but no development resulted from this work.

Jan 1, 1990

By F. J. Susko

The U.S. Bureau of Mines is using Fourier-transform infrared (FT-IR) analysis to investigate the bonding mechanism which occurs during the dewatering of clay slurries. High molecular weight polymers are used as flocculating agents in these processes. This investigation presents the results of an FT-IR study of calcium-exchanged montmorillonite treated with polyacrylamide (PAM) and polyethylene oxide (PEO). Both thin film and attenuated total reflectance (ATR) spectroscopic techniques were employed to study this clay-polymer system~ Results suggest PAM is adsorbed to the clay via the nitrogen atom of the polymer. A water bridge is involved in the bonding between the clay and PE~. Evidence also suggests that PEO may be adsorbed directly onto the surface of the clay.

Jan 1, 1990

By Corbett G, Iwai N

The Japanese gold mining industry has a long and productive history and is presently undergoing a period of revitalisation encouraged by the Hishikari discovery. Deposits exhibiting the characteristics of epithermal mineralisation are very widely distributed throughout the island chain and an encouraging number of these are large, seven containing gold in excess of one million ounces. All the important deposits are quartz vein type and contain extremely high grade, or "bonanza". Zones.

Jan 1, 1990

By L. Lui, A. Cauchon, A. R. Laplante

"The gravity circuit at Les Mines Camchib Inc. consists of two pinched sluices to bleed a feed to one of two 76 cm (30"") Knelson concentrator. The Knelson concentrate is upgraded to smeltable grade with a smaller Knelson (18/30 cm) and a riffleless table. Their tails are column cyanided and washed prior to recycle to the grinding circuit. This paper details size-by-size circuit performance. The Knelsons recover around 90% of free gold (as determined by Mozley Laboratory Separator), even below 37 µm. The sluices are ineffective, with upgrading ratios around 2, but approaching unity in the fine sizes. Much of the effectiveness of the circuit lies in the high gold circulating loads in the grinding circuit, which partly atone for the poor sluice performance, and the ability of the Knelsons to recover free gold. Secondary upgrading recovers slightly above 99% of the primary concentrate gold, 90% of it in a 65% Au concentrate and the balance in a heavily loaded (10 to 20 oz/st) pregnant solution. INTRODUCTIONBackgroundThe operating performance of the mill of Les Mines Camchib Inc. has been described earlier (Laplante et al., 1989). The presence of significant chalcopyrite (1 % and up) makes flotation necessary prior to cyanidation, to limit cyanide consumption and minimize environmental impact. In 1982, the presence of very high gold circulating loads in the grinding circuit lead to the commissioning of a gravity circuit, schematically shown in Figure 1. Gravity recovery of gold has been found beneficial because it increases metallurgical recovery by 1-3% (Laplante et al, 1987), as only part of the flotation tail is cyanided, and economic recovery, because of the lower net smelter return of gold in the flotation concentrate (as compared with the gravity concentrate). The latter increase is estimated, with a net smelter return of 95%, at 1.5% when gold recovery by gravity is equal to 30%. In early 1988, a sampling program was initiated to characterize the behaviour of gold in the grinding/gravity circuit. This paper reports on the results of this study."

Jan 1, 1990

By G. J. Simandl, H. -L. Jacob, S. Paradis, G. Valiquette

"Nos travaux de terrain dans le Grenville, effectués dans le cadre d'un projet d'inventaire des gîtes de wollastonite, ont démontré qu'il existe un secteur exceptionnellement favorable à l’exploration pour la wollastonite. Ce secteur s'étend de la municipalité de Grenville jusqu'au pare du Mont-Tremblant (nord de St-Jovite). D'autres secteurs favorables a 'exploration pour la wollastonite ont été délimités dans les regions du Lac-Saint-Jean, de Shawinigan et de la Gatineau. Neuf categories litho-structurales de gites de wollastonite furent identifiées. L'importance d'un système ou vert pour la formation des gîtes de hautes teneurs fut établie. Un guide de prospection pour la wollastonite propre à la province tectonique de Grenville fut développé. Plusieurs des indices sont prometteurs et mériteraient des travaux de raise en valeur afin de determiner s'ils représentent une source de wollastonite exploitable à profit. Lac-Saint-Jean, Shawinigan and Gatineau areas. Deposits may be classified into nine categories depending on their relationship to intrusive rocks, discordant or concordant contacts with the host rocks, morphology, and major structural controls. Deposits consist mainly of wollastonite, calcite and clinopyroxene. They may contain one or several of the following minerals: feldspar, scapolite, quartz, titanite sulphides, zoisite, clinozoisite, garnet, idocrase and prehnite. Wollastonite content may reach over 70%. Some deposits are associated with graphite veins. Better understanding of the geology, combined with the proposed classification provides new exploration guide for wollastonite. Several deposits have grades of economic interest. Further work is needed to determine if any of these deposits can be exploited for profit."

Jan 1, 1990

By M. Jennings

In 1987, Echo Bay discovered a major silver/gold ore body at their McCoy property in Nevada, and quickly made a decision to build a 5000 tpd mill which was expanded during the design to 7500 tpd. Since the ore reserves consisted of cyanide leachable oxide as well as sulfide, the plant flow sheet involved an oxide leach, a gravity circuit, and lead sulfide and a pyrite sulfide recovery by flotation. The paper describes the process development, equipment selection, plant design and the startup of the oxide treatment.

Jan 1, 1990

By Kubik K

This paper reviews the historical data on relative height changes of landmasses with respect to sea level for Pacific Rim countries.It discusses existing theories of the Greenhouse effect, and the interaction with the vertical movements of the continental plates which leads to different effects for different places. Possible future scenarios are described and directions for future research and measurement programs are given.Relative sea levels are governed not only the increase of water from deglaciation but also by a range of other factors such as variable water storage in lakes and the atmosphere, thermal expansion of the ocean, ocean currents, and the shape of the ocean and the continents. Sea floor spreading, for example, is ultimately more significant than deglaciation in sea level control but is generally much slower.

Jan 1, 1990

By Kobe HW, Balance PF, Black PM, Sporli KB, Smith IEM, Locke CA

The Hauraki Goldfield consists of a large number of volcanic-associated epithermal gold deposits within the Coromandel Volcanic Zone (CVZ), North Island , New Zealand; it is the most accessible and most studied of the Southwest Pacific gold regions. The deposits occur generally as steeply dipping quartz veins and breccia sheets in faults and fractures.From a tectonic perspective, the CVZ is generally considered a Neogene convergent volcanic arc constructed under an extensional tectonic regime; the common tectonic setting for epithermal mineralisation. The gold deposits are mostly hosted in subaerial andesitic arc-type volcanic rocks. Temporally, however, mineralisation is associated with rhyolitic rocks of a bimodal volcanic suite that may represent a back-arc environment. Rifting and calderas may be important components of the latter regime, but this is not yet clear; the general structural framework controlling the location of CVZ gold deposits remains poorly understood. Geophysics, particularly aeromagnetics, has a role in mapping regional fault patterns in the CVZ

Jan 1, 1990

By W. S. Fyfe

The future environment of our planet, with the concept of sustainable development, has moved to centre stage of all future plans for development. This global view is new. It presents great opportunities and challenges for the Earth Sciences. We have the tools to describe our environment on all scales - planetary to molecular levels. We must respond to this great demand by world society.

Jan 1, 1990

By Welby G. Courtney

This publication reviews recent U.S. Bureau of Mines studies of frictional ignition of a methane-air environment by coal mining bits cutting into sandstone and the effectiveness of remedial techniques to reduce the likelihood of frictional ignition. Frictional ignition with a mining bit always involves a worn bit having a wear flat on the tip of the bit. The worn bit forms hot spots on the surface of the sandstone because of frictional abrasion. The hot spots then can ignite the methane-air environment. A small wear flat forms a small hot spot, which does not give ignition, while a large wear flat forms a large hot spot, which gives ignition. The likelihood of frictional ignition can be somewhat reduced by using a mushroom-shaped tungsten-carbide bit tip on the mining bit and by increasing the bit clearance angle; it can be significantly reduced by using a water spray nozzle in back of each bit, which is carefully oriented to direct the water spray onto the sandstone surface directly behind the bit and thereby cool the hot spots formed by the worn bit. A bit replacement schedule must be used to avoid the formation of a dangerously worn bit.

Jan 1, 1990

By Qisu W

The ground vibration produced by the bench blasts of a single hole and a row of two or three holes is recorded in an iron mine. Using the seismic signal generated by a single-hole shot as the source function, we have developed a computer program of a simulating ground vibration by bench blast. The reasonable delay time of blast in the iron mine has been discussed tentatively with the Fourmap invented by Anderson, D.A. The seismograms measured from the single-row blasts of two or three holes have shown the method of simulating vibration is feasible on the whole. For large scale production blasts, a combination of the vibration simulation and the high-speed photograph is used to choose the delay Time.

Jan 1, 1990

By J. D. McKay

Flotation columns have been readily accepted for use in most sulfide flotation plants; however, recently columns are being used in many other areas. Recent improvements in design methodologies have overcome many operating problems and led to improvements in metallurgy. In addition, physical improvements in column design have simplified their operation while leading to better control. The Turbo-Air External Bubble Generator has provided a method for bubble size control and variation in air holdup and carrying capacity. These have enabled commercial operations to improve grades and recoveries by optimizing performance.

Jan 1, 1990

By Stewart Gillies A D, Just G. D

An internationally recognised and uniform method for classification, categorisation and designation of mineral and energy resources is not yet available. With the increasing need for reliable and comparable coal resource data it is necessary to standardise the traditional classification procedures by quantifying the three basic evaluation criteria of economic feasibility, geologic assurance and recovery. For well documented deposits, geostatistical methods can considerably improve classification quality. A review is undertaken of major classification with particular emphasis on those that incorporate limits on estimation error.A geostatistically based algorithm for classifying coal resources within the current Queensland and New South Wales codes has been developed.Application of the classification algorithm for resources from a number of seams exhibiting different structural characteristics is assessed. The method is found to give classification results that closely reflect the error associated with an estimate of resource quantities based on current sampling densities.lbis requires a careful geostatistical analysis with an emphasis on geological awareness. Resource category restrictions although albitrarily assigned should remain constant for all deposits being compared. This requires some engineering judgement with additional interpretation also required for isolated and peripheral block.

Jan 1, 1990

By Hani S. Mitri

The behaviour of grouted cable bolts used for rock reinforcement as a means of ground control in hard rock mining is investigated. The study utilizes an analytical model which is based on the variational principle to calculate the shear bond stress distribution along the embedded length of cable bolt. In this paper, a comprehensive parametric study which covers both geometric and mechanical design parameters involved is presented. Special emphasis is placed on studying the characteristics of the grout model represented by Winkler springs. This involved varying the maximum shear strength of the grout, its residual strength and the slip occurring between the cable and the borehole wall.

Jan 1, 1990

By Reilly SY, Green TH, O&apos

Alkali feldspar meggacrysts are commonly found (with aluminous clinopyroxene, kaersutitic amphibole, titanomagnetite, ilmenite and apatite, and more rarely with zircon and corundum) in alkalic basalts and their derivatives as discrete crystals and fragments. They are commonly euhedral or subhedral and may be up to 15 cm in size. Their occurrence has been reported from many localities around the world, e.g., Africa, Antarctica, eastern Australia, eastern China, East Fife (Scotland), Eifel (Germany), Massif Central (France), Mongolia, New Zealand, New Mexico (USA) and Siberia (USSR). These megacrysts are relatively homogeneous and belong to the Na-rich anorthoclase group, although Kutolin and Frolova (1970) called them sanidine due to their monoclinic nature. The majority of megacrysts have a molar orthoclase content (Or%) between 20 and 30 (Fig.1). These anorthoclase megacrysts possess a high degree of disorder, with the structural state belonging to the high albite-high sanidine series (Hoffer and Hoffer, 1973; Chapman, 1976).Published interpretations of the origin of anorthoclase megacrysts fall into the following two categories: either (1) Anorthoclase together with the associated pyroxene and amphibole crystallized from basaltic magmas as phenocrysts (cumulate phases) at high pressure and the present host basaltic rocks are the parent magmas for the anorthoclase megacrysts (Binns,l969; Binns et al. 1970; Kutolin and Frolova, 1970; Hoffer and Hoffer, 1973; Laughlin et al. 1974); or (2) Anorthoclase probably crystallized from a more evolved liquid at relatively lower pressure and was then picked up and carried to the surface by a later

Jan 1, 1990