Search Documents

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990

WILLIAM P BALAZ RMCMI PRESIDENT 1990-1991 on behalf of the RMCMI Board of Directors and Officers of The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 87th Regular Meeting and Convention to be held June 30, July 1 & 2, 1991 Keystone Resort, Colorado

Jan 1, 1990

By Badal R

Rock Discontinuities ("joints") affect blasting results. An investigation was carried out to understand if blast parameter such as spacing needs to be altered with the change in joint direction. Small scale laboratory studies in jointed limestone blocks have been carried out. It is shown that optimum spacing is variable with the "joint" orientations. Evidence is presented from field studies in four limestone quarries supporting laboratory studies. Reasons for success and failure of widespacing technique is also provided. Only with suitable orientations of "joints: widespacing is successful.

Jan 1, 1990

Identify abnormal low-frequency blast vibrations. Develop blast design procedures for such adverse vibration cases, including the selection of delay times based on ground conditions, vibration frequency, and structural response. The Problem Research by the Bureau of Mines and others has demonstrated how structural response and the potential for cracking and other damage depends on blast vibration frequency in addition to particle velocity amplitude. The Bureau has published recommended criteria for blasting near low-rise residential-type structures; criteria that specified frequency-dependent amplitudes. The typical vibration frequency from surface mine and quarry blasting is 20 hertz (Hz). Sites have been found, however, that regularly produce ground-roll-type waves with frequencies as low as 4 Hz. The most serious cases arc those where vibration frequencies fall in the natural frequency range for structures of 4 to 12 Hz. Such vibrations have a higher potential for causing, damage to residential structures, particularly at the low end of this frequency range, because of the resulting high strains these frequencies produce in structural materials.

Jan 1, 1990

Cataclysmic or flood-like release of gas-charged brines, hydrocarbons and slurries accompanied widespread mineralisation of Upper Devonian environments. These are well represented in the Canning and Burdekin Basins of Western Australia and Queensland respectively.The Burdekin Basin provides particularly instructive vein structural sequences. These fall into organic residue to carbonate paragenetic sequences which are known elsewhere to record progressive decarboxylation. Fibrous veins indicate overpressure in fractures with organic residues, acids and gas derivatives driven to overlying groundwater flows. This combination of large flow rates and potent organic mineralisers led to extensive arsenical rare-metal mineralisation which is similar to that concentrated in Upper Devonian extinction horizons of the Canning Basin. Organic-residue mineralisation appears concentrated by certain hvdrostructures and targeted upon particular species. These controls need to be understood to guide modern management stragegies for mineralised organic and nitrogenous wastes.

Jan 1, 1990

By N. S. Raghavendran

Based on the weld pool length and width calculations due to an empirical model (1) for submerged arc weld metal, an elegant quantitative definition of tandem submerged arc welding is established. On the basis of this theoretical consideration optimum welding parameters for joining 25 mm thick low carbon steel plate in two passes by tandem wire submerged arc welding have been experimentally found out. An assessment of the metallurgical quality of weld metal and the dependence of mechanical propenies on pool overlap has been made. Also the solution of Rosenthal (2) etc. for a moving point source of welding, which was used as a guide line in formulating the empirical model for the calculations of weld pool dimensions, is compared with the solution of empirical model for submerged arc weld pool dimensions.

Jan 1, 1990

By V. Gall

The three-dimensional finite element technique combined with the progressive failure approach was utilized to simulate stress distributions in a mine section which occur in response to a longwall mining operation. Due to the availability of the Cray supercomputer, a large-scale three-dimensional finite element model was developed for the analysis. The Hoek-Brown failure criterion, which describes a realistic behavior of rock masses, was used for the simulation of progressive failure. A comparison of calculated and monitored stresses in the mine has shown that the model gives a good representation of stresses in the mine structure.

Jan 1, 1990

By Donchak P. J, Champion D. C, Fordham B. G, Domagala J

The Hodgkinson Province forms the northern part of the Tasman Orogen and contains the most extensive outcrops of Silurian - Devonian rocks in Queensland. Deep-water, marine siliciclastic sequences (mainly turbidites) dominate most of the province except near the western margin where mafic volcanics and fossiliferous limestones characterise much of the succession. It is difficult to apply normal stratigraphic mapping techniques to the Hodgkinson Province because of extensive stratal disruption by numerous thrust faults, the general lack of stratigraphic and structural markers, and the unfossiliferous nature of much of the succession. Nevertheless, several distinct units have been delineated although their internal stratigraphy or boundary or superpositional relationships are uncertain. Ordovician strata, as well as two major unconformities have been recognised in the western part of the province. Several models have been proposed to explain the evolution of the Hodgkinson Province. Although there is no general agreement most recent researchers favour an extensional tectonic regime.

Jan 1, 1990

By V. F. Hollister

Copper and gold were discovered in the Copper Canyon area of the Battle Mountain district of Lander County, Nevada, in August of 1866. By 1876 a gravity plant was con¬centrating oxidized Copper Canyon copper-gold ores. The history of mining in the district to 1967 has been summarized by John E. Frost (in press) as a case history of the discovery of the Battle Mountain porphyry copper deposits. His summary is not repeated here; rather, the present case history covers exploration since 1967, primarily for gold ores. Subsequent to the construction by Duval of facilities to mine the porphyry copper deposits in 1967, Duval established a geologic staff at the mine to continue district exploration. The staff was guided by David W. Blake, who acted as chief geologist for Duval's exploration in this part of Nevada. Blake's activities led to the publication of numerous technical articles, including his contribution to the US Geological Survey Professional Paper 798-B. A part of that volume is attached as a reprint (pages 23 through 66) as an explanation of the geological setting of mineralization in the district. The work by Blake and his staff recognized metal zonation in the skarn environment at Copper Canyon, and their studies were incorporated in the development of the Tomboy-Minnie gold deposits that are peripheral to the porphyry. Exploration continued beyond the immediate vicinity of the porphyry and the Fortitude ore zones were discovered. These skarn deposits are described in the attached article by Wotruba, Benson, and Schmidt, published in the July 1986, MINING ENGINEERING. The continued exploration successes at Battle Mountain reflect on the well organized and effective exploration team developed at the mine. The team has provided successive discoveries in a district known mostly for ore bodies that are exhausted in a few years' time.

Jan 1, 1990

By E. K. Albert

Title IV of the 1977 Surface Mining Control and Reclamation Act (SMCRA) provides for an abandoned mine reclamation fund. This fund, taken from fees collected from operating coal mines, provides capital for the reclamation process. The Act directs the Office of Surface Mining (OSM) to collect the fees based on coal production. Monies from the abandoned mine lands (AML) fund are distributed through two programs. The first provides OSM with capital to use in emergency situations resulting from abandoned mine sites and reclaiming high priority sites in states without established AML programs. The second distributes the money through a state's AML program in the form of grants. To provide for a flexible and customized selection procedure for AML projects, a management information system (MIS) that combines scientific selection procedures is being developed. This system employs objective and subjective methods developed in systems research in recent years. The MIS component is an essential part of any selection process involving large numbers of potential projects. It must contain all the necessary project parameters that can be applied to the selection of projects whether or not they are to be used in the immediate selection criteria. In addition, variable selection criteria will allow ‘what if’ types of inquiries for comparison of differing selections and benefits.

Jan 1, 1990

The intention of this paper is to examine the practical and technical aspects associated with the measurement of blasting related phenomena. The emphasis is directed towards the acquisition of quantitative data rather than its theoretical interpretation. The application of advanced technologies will require that many more people involved with blasting become familiar with this topic. Against the many other disciplines where measurement may be beneficial, blasting is peculiar on several counts. 1) It must almost always be carried out in the field, and very often in a production environment. 2) Much consideration must be given for the safety of personnel and equipment. 3) The process is dynamic and seldom repeatable. Because the blast process is so dynamic there is little opportunity for direct examination. For this reason measurements are almost universally made using electronic techniques. In this way the event can be captured faithfully as it occurs and later examined in detail, after the fact. It is obvious that some familiarity with these electronic techniques is a necessary ingredient for successful blast monitoring.

Jan 1, 1990

By Lowell J. D

This paper is an outgrowth of a continuing compilation of the geology of Chilean ore deposits by Carlos Ruiz who was the author in 1965 of Geologia y Yacimientos Metaliferos de Chile which was the definitive compilation of the ore deposits of Chile. A new version was written by him in 1988, with the co-operation of Federico Peebles L, published in Geologia, Distribucion y Genesis de los Yacimientos Metaliferos Chilenos. Over the past eight years J David Lowell studied the geology of the Chilean mineral belts in connection with planning mineral exploration for copper and gold.

Jan 1, 1990

By D. J. Gurtler

On January I, 1988, Chino Mines Company initiated the use of a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction-electrowinning plant feed and non-ore material to determine its disposition. Post-implementation studies indicate that a significant increase in financial returns on material mined was realized when compared with the copper cut-off grade previously in use.

Jan 1, 1990

By C. O. Bounds

Management of emission control dust from electric? arc furnace (EAF) steelmaking as an RCRA-EPA listed hazardous waste places economic and environmental pressures on the steelmaking industry. Horsehead Resource Development Company, Inc. (HRD) serves the industry by recovering nonferrous metals from the dust in rotary kiln plants in Palmerton, PA and Chicago, IL, and has demonstrated the commercial viability of its patented coal-fired FLAME REACTOR Process. However, because of location and/or regulation, many steelmakers could be more economically served via on-site processing of its dust. Therefore, in 198-7, through a contract with the Gas Research Institute, HRD embarked on a program to develop a gas-fired reactor and test a prototype unit. The development program has successfully proven the environmental, technical and economic performance of the concept. Consistently high zinc, lead and cadmium recovery to an oxide concentrate as well as production of a nonhazardous, delistable slag have routinely been achieved. The gas-fired FLAME REACTOR field experiment results and the economic performance of on-site or smaller regional plants will be highlighted.

Jan 1, 1990

By Jay A. Berger

Nondestructive testing of deep foundations for integrity problems made great strides in the late 1980's. Inexpensive portable computers have allowed the immediate and rapid processing of field measured acceleration records which can provide insight into the relative structural integrity of a previously installed foundation member. Although the gathering, processing and displaying of the data is now straightforward, interpretation remains at times rather challenging. This paper provides a brief introduction into the theoretical basis for data interpretation and the hardware necessary for data acquisition. Five case studies are discussed which demonstrate the varied applications of low strain integrity testing of deep foundations and the efficiency at which they are completed. BACKGROUND One dimensional wave mechanics, when applied to a linear elastic pile with a length that is an order of magnitude greater than its width, provides a straightforward basis for the interpretation of motion measurements made at a pile top. When impacted, a stress wave travels through the pile at a wave speed, c, which is a function of the elastic modulus, E, and mass density p (i.e., E=pc2). The applied load F, and particle velocity v, at a point are related by the equation F=Zv. For a cross-sectional area A, the proportionality constant Z is equal to EA/c. Because Z is a measure of the pile's resistance to change in velocity it is called the pile impedance.

Jan 1, 1990

By Alain Simard, André Gobeil, Sylvain Lacroix, Maurice Rive, Denis Racicot, Pierre Verpaelst

"The Abitibi volcano-plutonic belt forms the major portion of the Abitibi lithotectonic subprovince in the Superior Province. The Abitibi belt is composed essentially of"" (1) approximately 2.7 Ga old volcanic and sedimentary rocks; and (2) gabbro, tonalite, granodiorite and syenite intrusions occurring in well-defined prekinematic ( synvolcanic ), synkinematic and post-kinematic plutonic suites. Most of these rocks are metamorphosed to greenschist facies. Regional multi-phase deformation affects the volcano-sedimentary rocks. Deformation was initiated as these rocks were formed, and peaked at the end of the Keno ran orogeny with the emplacement of granitic batholiths.There are 145 former and current mines in the Quebec segment of the belt. To date, more than 420 Mt of ore have been extracted yielding 1,600 tonnesof Au, more than4,000 tonnesof Ag,4,400,000 tonnes of Cu and 5,300,000 tonnes of Zn. Mineral production is concentrated in geologic domains that approximately coincide with the boundaries of lithotectonic domains. We have compared the geology and mineral deposits of different domains to illustrate their distinct metallogenic signature. Certain domains are dominantly gold-producing (Cadillac-Malartic, Val-d'Or, Caopatina), others are base-metal producers (Matagami and Normetal), while others produce both gold and base metals ( Rouyn-Noranda, Chibougamau, Casa-Berardi-Joutel).Gold is extracted from quartz-rich vein deposits (for example, Val-d' Or), sulfide-rich veindeposits(Cadillac or Chibougamau) and from volcanogenic massive sulfide deposits ( Rouyn-Noranda). Base metals are generally mined from volcanogenic massive sulfide( RouynNoranda, Matagami, Normetal), although certain vein deposits yield base metals (Chibougamau) . Certain sectors are dominantly zincrich (Matagami, Normetal)."

Jan 1, 1990

By III Sadler

Processing bauxite and clay ores to reduce Iron content to levels low enough for the ores to be suitable raw materials for such products as refractories and abrasives has long been regarded as a diffi9ult problem. Standard magnetic separation processing of the untreated ore has been attempted by previous investigators with only limited success due to the finely divided state and weak magnetic susceptibility of the iron minerals (hematite, geothite, etc.) present in these ores. The new process described in this paper consists of calcining the finely crushed ore at 500 to 800 C and then reducing (with hydrogen, carbon monoxide, etc.) the iron oxides present to magnetite or elemental Iron. The magnetic susceptibility of iron in these forms is enhanced 40-to 100-fold over that of hematitie and is readily removed by simple magnetic separation. Starting with a 2.7% Fe20s Alabama bauxite ore, a 1.5% Fe20s product was produced in one pass through a Davis tube magnetic separator with 95 + % recovery of the iron-free bauxite fraction and a 20% Fe20a magnetic product. These findings suggest that with the addition of light calcination, reduction and magnetic separation steps to the conventional refractory grain production process, the large U.S. reserves of high-iron bauxites could be used.

Jan 1, 1990

By D. H. White

The term "block caving" as used in this text includes panel caving and mass caving as described by Julin and Tobie (1973). This method reportedly was conceived in 1895 when a block of ore ranging up to 200 ft (61 m) in width was undercut at the Pewabic Mine on the Menominee Range in Michigan (Bucky, 1956). Over the years this method has evolved largely as a consequence of trial and error in which operators became acutely aware of what nature would allow and what it would not. Today block caving remains somewhat of an art rather than a science where experience often dictates what needs to be done. With the plunging prices of base and specialty metals in the early 1980s caving mines sought to reduce operating and development costs in order to return to profitability. For some this became an impossible task given the design, grade and operating costs of the day and closure became the only alternative. One lesson learned from the experiences of the 80s is that survivability depends on cost competitiveness and this implies the efficient use of resources and technology. To this end applied rock mechanics serves as a useful tool. The purpose of this paper is to show how Geomechanics can be used? in block caving to facilitate sound decision making and how this equates to dollars saved. Features of mining method selection, design and operation are discussed as related to this theme.

Jan 1, 1990

By Juras ST, Krouse RH, Godwin CI

The Buttle Lake camp is in central Vancouver Island, southwestern British Columbia, Canada. The camp hosts world-class polymetallic volcanogenic deposits of Devonian, Frasnian age (370Ma). This paper describes an on-going sulphur and lead isotope study of the major orebodies.Sulphur isotopes were determined for sulphides (pyrite, chalcopyrite, bornite and galena) and sulphate (barite). Sulphide analyses are markedly different from sulfate. The differences are explained below in a unique model.Sulphide isotopic compositions cluster tightly (del34S -6.7 to 4.6), and demonstrate isotope reversals. Calculated temperatures of correctly ordered mineral pairs are unrealistically high. We conclude that the sulphides are in isotopic disequilibrium, presumably because of rapid precipitation from a quenched plume in an anoxic environment, and because of subsequent sulphide replacement.

Jan 1, 1990

By Yael Miron

This report describes laboratory studies by the U.S. Bureau of Mines to determine the suitability of a static oxygen (OJ adsorption test for evaluating the self-heating tendencies of coals. Reliable minimum self-heating temperature (SHT) values from adiabatic oven tests were used as standards for comparison and evaluation. A suite of six coals was tested in the adiabatic oven and in sealed flasks. In the latter tests, both undried and dried samples, in a range of four particle sizes, were examined. Miniature pressure trans-ducers monitored pressures in the flasks, and gas samples taken at the end of the tests quantified all the gases present. An excellent correlation was found between the minimum SHT's and amounts of O2 adsorbed over a 7-day period for dried coals, independent of particle size. In addition, a good correlation was obtained between the minimum SHT's and pressure changes in the flasks at the end of the test for the same coals, also independent of particle size. Based on these results, the sealed flask test can be reliably used to determine the self-heating tendency of a bituminous coal sample.

Jan 1, 1990