Search Documents

By Moelle KHR

The successful operation of a longwall face depends significantly on the efficient actions by support systems and on the ability to form a supported beam for a limited time span.The mechanical action of the supports can set up complex stresses in the immediate roofstrata.The cyclic application of supporting loads to the immediate roofstrata of a longwall face creates a special type of fabric disintegration in the rocks -affected. The mode of application and the distribution of the supporting forces is thus severely modified in a number of cases.The occurrence of true fatigue damage in brittle sandstones has been identified by studying the subcritical crack growth and microcrack development in the fracture-tip region. Several mechanical effects peculiar to the cyclic fatigue process have been identified. These effects had not previously been widely recognized. Damage in brittle rocks subjected to cyclic loads is shown to be distinctly different from any other damage processes under either monotonic or sustained (creep) loading conditions. The face support systems will frequently support rockmasses with mechanical properties not identified in conventional monotonic or sustained load tests.

Jan 1, 1991

By Komosa T, Muir D. M

Adequate levels of dissolved oxygen are essential for efficient gold dissolu- tion. The actual levels in plantpuips can be seriously reduced by the presence of oxygen consuming reactive minerals, and reduced oxygen solubility in saline water. The rate of gold dissolution is then limited by oxygen availability rather than cyanide. Ion selective electrode dissolved oxygen meters can give an effective indication of the relative oxygen saturation, but they are not able to give meaningful values of dissolved oxygen in saline water, without custom calibration curves. When the dissolved oxygen concentration is rate limiting, the addition of oxygen or peroxide can improve gold leaching kinetics as well as reduce cyanide consumption.

Jan 1, 1991

By W. Choi

The present study revealed that the bioleachability of a chalcopyrite flotation concentrate is influenced by the semiconductor properties of CuFeS2. The overall reaction of biooxidation,

Jan 1, 1991

By D. Boreck

The Bureau of Mines is conducting research on the feasibility of incorporating in situ stope leaching into active underground metal mines. Stope leaching, a modified in situ leaching technique, proposes to recover metals by leaching fragmented ore in existing underground openings and collecting and processing the metal-bearing solution to recover the valuable metals. If leaching solutions escape from the stope, either through geologic discontinuities or highly permeable zones in the rock, valuable metals dissolved in the solution may be lost. Escaping solutions may also contaminate ground waters. Consequently, in fractured rock, the characteristics of the fractures in the vicinity of the leaching stope must be understood before introducing actual leach solutions into the stope. Effectively characterizing a rock mass requires the integration of several disciplines including structural geology, borehole geophysics, hydrology, geochemistry, and mining engineering. This paper will focus on the general geologic and geophysical techniques that can be used to characterize the rock mass at an underground simulated stope leaching site. The results of several geophysical logging methods, tested at the site, are compared to the geologic core descriptions. Then, the? effectiveness of the different geophysical techniques in delineating fracture zones will be assessed. Knowledge gained through the geologic and geophysical analyses can be used to supplement results from hydrologic testing. This information can also be utilized in designing blast patterns and developing strategies for controlling or blocking movement of escaping leach solutions.

Jan 1, 1991

Selective Flocculation process development generally involves single mineral flocculation tests to identify the appropriate polymer and experimental conditions for achieving the desired selectivity. Invariably the selectivity predicted on the basis of such tests is not realized when mixed mineral tests are conducted. A systematic experimental investigation revealed that adsorption of the polymer on various substrates is critical to selecting the suitable flocculent. Simultaneously, a mathematical model was developed to predict the overall process efficiency with a given polymer. In this paper, results of these efforts to scientifically design a suitable selective flocculation process are presented.

Jan 1, 1991

By K. F. Unrug

Martin County Coal Corp. is located in Martin County, KY, in the Appalachian coal fields, near the West Virginia border. The company's total leasehold covers more then 133.5 km' (33,000 acres). Total annual production at Martin County Coal Corp. is currently 2.2 Mt (2.5 million st). In certain years, though, it exceeded 2.7 Mt (3 million st). About 45% of the annual production comes from two surface mines. The balance is produced from five underground mines. Martin County Coal's work schedule consists of two nine-hour shifts a day, 240 days a year. Topography The topography of the area is characterized by rugged hills and ridges and sharp V-shaped valleys demonstrating a cliff and slope topography. This topography consists of alternating benches of outcrop sandstone and slopes. The deep valleys have been carved out by many small streams in the area. These streams are contained within the steep slopes of narrow, twisted mountain ridges. The ridges are underlain by massive sandstones that, being resistant to erosion, create sharp, rocky morphology. The height of the hills above the valley floors ranges from 122 to 244 m (400 to 800 ft).

Jan 1, 1991

By M. Phylli Bray

"Concurrent with the continuing demise of many Canadian mining towns is the rise of a new method of providing remote mine sites with a workforce. This is the Long Distance Commute (LDC) which uses commuter labour and requires no permanent settlements to support the mine operation. It provides a flexible and cost effective method of operation to the industry and relieves both governments and industry of the expense of building and maintaining mining towns. However, little attention has been paid to the effect on workers or their families of the LDC work schedule whereby workers spend a fixed number of days at the site followed by a fixed number of days at home. Off-shore oil rig experience would indicate that negative social impacts may be expected. Research leading to an understanding of the problems involved seems to be indicated. One innovative suggestion has been to use already established but dying mining towns as workforce pick-up points for new LDC operations further north.BackgroundUntil recently, mine towns were considered as a necessary component of mine development. This was a natural symbiosis resulting from the need to provide workforce accommodation close to isolated mine sites. The early mine communities in Canada were often just a huddle of shacks around a head frame. Gradually mining companies began to provide housing which varied from basic duplexes and quads in grid pattern layout to professionally planned and designed towns, either model company towns or the more recent suburbs-in-the-bush, the so-called ""instant towns"" of the postWorld War II era of resource development. The improvement in accommodation reflected the need to attract a stable workforce as mine operations became more sophisticated. City amenities were expected and offered in these mine towns as a way of encouraging a permanent community of mining families. Indeed in towns like Manitouwdage, Schefferville, and others, it was not unusual to find a significant percentage of two- and three-generation families apparently providing the permanent mining communities so desired by mine operators."

Jan 1, 1991

By Richard D. Hagni

An enhanced Interest in pyrometallurgical dusts has recently emerged due to increased world-wide environmental concerns. Mineralogical study of dusts samples from lead sinter plants. lead smelters, and secondary steel mill electric arc furnaces has shown that they can be readily studied by reflected light microscopy. These dusts typically are composed of small particles sufficiently large that their mineralogical identification and characterization can be conducted under the reflecting light microscope. Scanning electron microscope-energy dispersive spectroscopic analysis (SEM-EDS) has been used to confirm optical identifications and chemical compositions. The sinter and blast furnace dusts at the Doe Run Smelter at Herculaneum, Missouri are commonly about 20-150 11m. They consist predominantly of galena, chalcopyrite, sinter. slag. coke. and particles. Dusts from remote sampling sites 112-1 mile from the lead smelter are composed of similar particles and abundant fine-grained particles, less than 10 um. of locally derived calcium-aluminum silicates. Electric arc furnace (EAF) dusts are mostly spherical and less than 10 11m. They consist predominantly of iron oxides (magnetite. franklinite. jacobsite and solid solutions of these spinels), zincite. and calcium-iron silicate glass, together with smaller amounts of hematite. sylvite. coke and metallic iron. Reflected light microscopy is rapid provides mineralogical data on individual grains within dust particles. and allows direct observations of textural intergrowths in pyrometallurgical dust particles.

Jan 1, 1991

By Han Jie

The results of full scale plate load tests on stone columns on soft clay in coastal areas are presented in this paper. Four load tests were made, two of which were performed on the ground treated with stone columns, one on an isolated stone column and the last one on the untreated ground. For a given stress range, the settlement of the rigid plate, the stress concentration factor, and the excess pore water pressure were measured. It is found that the distribution of vertical stress beneath the rigid plate supported by the composite ground of stone columns is very different in shape from the one by the untreated ground, that the stress concentration factor has a relation with the stress level and time, that the stone columns increase the bearing capacity up to by 2 times, and that the ground stabilized by stone columns is of great advantage to keep the foundation stable.

Jan 1, 1991

By J. Pang, S. Chander

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and impedance spectroscopy techniques. The cyclic voltammetry was used to elucidate oxidation/reduction reactions, whereas impedance spectroscopy was used for in-situ characterization of the interface. To analyze the impedance spectra, equivalent circuit models were constructed based on a layer- wise growth of reaction products. Parameters of the equivalent circuit were calculated by comparing the experimental spectrum with that expected on the basis of equivalent circuit. From the value of equivalent circuit parameters, properties of the surface layers were inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution. From such changes the effect of oxygen and collector concentration on the contact angle and flotation behavior of chalcopyrite were interpreted.

Jan 1, 1991

Kensington is a joint venture between Echo Bay Mines and Coeur Alaska, a subsidiary of Coeur d'Alene Mines Corp. The venture is of equalparticipa- tion and is governed by a management committee with Echo Bay as the operator. The project site is 50 miles north of Juneau, Alaska on the eastern shore of the Lynn Canal. The mine and mill are being planned for a production rate of 4,000 stpd. Currently, probable reserves stand at just over 11.3 million tons grading 0.149 oz Au/ton. The project is now in final feasibility study with a production decision anticipated by the end of 1990. Commercial production would begin early in 1993. This presentation dis- cusses the anticipated mine, mill and support aspects of the project.

Jan 1, 1991

By Thomas A. Colbert

Permanent reclamation of tailing and acid forming mine wastes in the western United States has been largely a losing proposition. There have been few if any successes without actual burial of wastes with soil, overburden, waste rock or other material more amenable to reclamation. Rather than major breakthroughs, development of new techniques has been slow and steady. Revegetation of acid forming wastes with little or no soil cover is now probably feasible. Three key elements include the use of adapted plant species which are now becoming commercially available, lime and selective bactericide for controlling acid, and organic amendments such as manure or sewage sludge. Benefits of this type of reclamation often include reduced mobility of toxic metals and improvements in water quality. With a stringent regulatory regime for mine wastes impending under Strawman II, the importance of good, economical reclamation techniques will become critical to successful and profitable western mining operations.

Jan 1, 1991

By Walter E. Heinrichs

This case history really started during the tail end of WWII when two Navy men, both Colorado School of Mines graduates, got together in Washington, DC, while they were assigned to the Office of Navy Petroleum Reserves doing some of the first aerial magnetometer work ever done on a practical oil exploration basis over the offshore area of the Gulf Coast. When separated from Naval Service active duty in 1946, the two men, Walter E. Heinrichs, Jr., and Robert E. Thurmond, tried, unsuccessfully, to form a commercial air magnetometer business. Later they got together again in Jerome, AZ, with Newmont Mining's early geophysical exploration endeavors from 1947 to 1949. Subsequent to the Newmont experience, they jointly proposed a specific mining geophysical exploration and development program to Herbert Hoover, Jr., then president of United Geophysical Co. of Pasadena, CA. Mr. Hoover, in consultation with his father Herbert Hoover and others of his staff at United, particularly Edwin G. Schempf, executive vice president, and Raymond A. Peterson, vice president of research, agreed to establish the proposed program under United's auspices, to be headquartered at Tucson, AZ. The primary objective would be to practically test and develop various mining geophysical methods and techniques while exploring particularly for base metals in the general area of southeast Arizona and southwest New Mexico.

Jan 1, 1991

By B. Ainsworth

The 1972 discovery of the Howards Pass lead-zinc deposit was the product of systematic regional geochemical surveys used to evaluate conceptual geological models for the metal-rich black shales of the Selwyn Basin. Motivation of personnel involved in all aspects of work was as critical a factor to the success as the existing corporate attitudes and infrastructure. Exploration programs were flexible but maintained a focus only on targets of sufficient economic potential to support operations in remote locations. Direct costs for the programs that lead to the discovery were in the order of $500,000 (Canadian 1972). Geological reserves today stand at over 500 Mt (511 million st) of 7% combined lead-zinc, containing a higher grade zone of nearly 10 Mt (11 million st) of 16% combined lead-zinc.

Jan 1, 1991

By S. P. Banerjee

There has been a phenomenal increase in production of coal from opencast mines in India. At the same time environmental problems caused by mining are receiving greater atttention. Deterioration in ambient air quality due to increased concentration of suspended particulate matter (SPM) in and around an opencast project is a major problem. Some measured values of SPM level around opencast mines in diff coalfields show that in many cases the TLV of 500 ug/m^3 is exceeded. The impact of dust emission from a mining project on surrounding areas are estimated by using computer models for air pollution dispersal but such treatment suffers from errors in predicting the dust load and failure to take into account the terraced nature of the opencast mine site. The haul roads have been identified as the most prolific source of dust and some recent trials on haul road dust consolidation in Indian mines are mentioned in the paper. Statistics regarding pneumoconiosis cases in Indian coal mines for the last decade are presented to show an increase in reported cases and a gist of the recently amended regulations on the subject of precaution against dust is mentioned.

Jan 1, 1991

By Jorj O. Osterberg

The practice of using side shear resistance in the design of drilled shafts socketed in rock is discussed. In the absence of field test data for the particular rock involved, the designer often neglects the side shear altogether or uses an extremely conservative value. The uncertainty of using strength data from compression tests on rock cores is discussed. Examples of full scale load tests are given which illustrate that even in the weakest of rocks, considerable side shear resistances are obtained, enabeling reductions in the depths of the sockets and consequent savings. Existing Practice. The existing design practice in using side friction/bond between a drilled shaft in rock or hard soil varies very considerably in different areas of the U.S., in different areas of the world, among different Geotechnical Engineers, and in the requirements of different building codes. In fact, the variation is so great that it is inconsistent and contradictory. For example, in Florida where fairly weak coral limestone and sandstone is prevalent, the general practice is to use side friction only and to allow no end bearing. In Chicago, Detroit, Boston and other areas where soft clay overlies stiffer clays, hardpan and limestone or other hard rock, the common practice is to allow for no friction and to use end bearing only, even though the lower portion of a shaft frequently penetrates stiff to hard clays and hardpan (glacial till) before bearing on hardpan or rock. In Hong Kong, if the hole is stabilized with drilling mud, no end bearing is allowed. In Boston (Thompson, Erikson, and Smith, 1989), two tests at two sites on 18 inch pipe piles penetrating 100 feet of soft clay and driven only inches into an argillite, tested 140 and 210 tons in ultimate side shear resistance. Certainly, with long drilled shafts, no matter how soft or weak the soil or rock is, some if not considerable side friction occurs, and where drilling mud is used, there must be considerable end bearing.

Jan 1, 1991

By J. A. M. Cano

An extensive research work was developed by Samarco Mineracao S/A to study the quality characteristics of blast furnace pellets produced with high content of MgO. Comparative blast furnace simulation tests were conducted both in Samarco and foreign laboratories. The objective was to evaluate the behavior of high MgO and normal Samarco pellets in the blast furnace operation. Additives such as dolomitic hydrated lime, dunite and magnesite were used for increasing pellet MgO content. The test results showed that pellets produced with high MgO content are similar in quality to normal Samarco Pellets.

Jan 1, 1991

By J. D. Miller

Gold adsorption from cyanide solutions by activated carbon has been studied at great length during the past decade. Findings from past research are reviewed and discussed with respect to structural features of various carbons, including carbon black, activated carbon, graphite and diamond.

Jan 1, 1991

By L. A. Morley, S. C. Gambrell

Behavior of a jour-leg shield design used on a soft floor in an operating longwall system is presented. The shield examined in this study was constructed having a split base and a split caving shield. Attention is focused on other-than-normal loading on the canopy and its effect on deformation of the lemniscate links. Examples of the magnitudes of typical bending and twisting deformations are given. Schematics of the canopy, caving shield, and lemniscates showing important forces and moments are presented. Approximate minimum values of the forces and moments required to produce the deformations are calculated based on the mechanical properties of the material. The need for use of more inclusive three-dimensional design techniques is demonstrated.

Jan 1, 1991

By Jin Anshi, Wang Dai, Wang Zingshen

Both fire and gas problems in Fully Mechanized Sublevel Caving Coat Face are quite different from those in common fully mechanized coal face. Pouring N2into the goaf would be the best method to prevent fire in the goaf. In this paper how to determine parameters of pouring N2 is discussed. Comparing distributions of gases and temperature before pouring N2into the goaf with those after pouring N2 into the goaf, the effectivenesses of preventing the fire by pouring N2 into the goaf are testified. Some special gas problems appear in Fully Mechanized Sublevel Caving Coal Face, which are proved to be serious and interrelated with pouring N2 into goaf. Finally, a few methods adopted to deal with gas problems are described simply.

Jan 1, 1991