Search Documents

By Bounsombath P

Underground mine development remains as one of the most important factors in cost effective mining. Various forms of continuous development have been proposed with some of the earliest conceived centuries ago.The bore, fire and muck approach remains, in the late 20th century, as the predominant method of underground development, despite intense efforts over the past decade or so to develop other systems.Following a comprehensive analysis of development in the Australian mining industry, the reasons why the traditional development cycle has remained unchanged are identified and potential directions for the future are suggested.

Jan 1, 1992

The Western Cape Branch of the SAIMM recently held a one-day colloquium on the use of artificial intelligence (AI) in process engineering in the I.S. Gericke conference room at the University of Stellenbosch

Jan 1, 1992

By D. E. Ranta, George F. Weaton

Estimating the Iron Ore reserves of Minnesota are directly related to both the geology of the deposit and the Scandinavian heritage of its people. The flat lying deposits, when properly prospected, make estimating easy and accurate across wide areas of the Mesabi Range. It also makes taxation simple on the unmined reserves. The reserves are their heritage and all the people should benefit, not just the owners. Heritage also dictates that newly discovered ores were there before discovery, hence, subject to the omitted property tax and liable for six years back taxes.

Jan 1, 1992

By Pharis E. Williams

The ability of voids, microballoons, and even solids to sensitize explosives has been known and used for many years. This phenomenon has generally been studied and reported under the terminology of "hot spots" because of the increase in local pressure and temperature when a shock wave encounters such sensitizers. A method for treating this phenomenon in detonation theory or in a detonation model has been studied for almost the same length of time. Perhaps because of the complexity and non-linearity of the void, or microballoon collapse, several of these studies have used the expediency of including additional terms in the burn rate law to account for the influence of hot spots. The detonation model proposed here considers the sensitization due to discontinuities in the shock impedance to be a mechanical phenomenon to be accounted for in the mechanical equations governing the detonation and not in the burn rate law. While this is not a new contention, the method for handling this non-linear phenomenon within the proposed model is new. The model also includes a method which accounts for the manufacturing variables of emulsion matrix cell size, microballoon size and type, as well as energetic additives.

Jan 1, 1992

By A. David MacPhail

"Highland Valley Copper is a large volume producer of copper and molybdenum concentrates. Production is by conventional truck and shovel operation combined with an extensive ore handling in-pit crushing and conveying system.Grade of the two orebodies is low at 0.4% copper and 0.007% molybdenum and this demands a production rate in excess of 260 000 tpd at a stripping ratio of 1: 1. Mining cost has to be kept at minimum levels to keep the mine profitable and thus, it is necessary to keep in the forefront: of technology. As well as the in-pit crushing system, the mine has pioneered the use of shovel weighing coupled with a state-of-the-art dispatch system.Maintenance of the equipment is carried out at the on-site mine maintenance shop with assistance from local shops for engine and wheel motor rebuilds and other large jobs such as those requiring stress relieving. Shovel and truck rebuilds are undertaken by mine crews. Both long- and short-term planning is designed and scheduled in the mine engineering section. Outside consultants are used to assist in slope design, reclamation and blasting technology."

Jan 1, 1992

By Sergio Godoy P.

The Los Bronces porphyry copper deposit is located in the high Andes of Central Chile. Ore is mined from several tourmaline breccias and from an earlier porphyry. After years of experience in the geostatistical estimation of reserves in different zones of the ore body, we believe that success lies in considering the evaluation as an integrated process beginning with the analyses of the drilling density and sampling methodology, ending with the critically important reconciliation between the estimated and the actually extracted ore, in general, when errors or differences occur, focus is centered in the calculation stages of geostatistics. However, this paper demonstrates that all the evaluation stages are equally important and require the direct and continuous geologic input to ensure the best possible estimate within the frame of the geologic constraints.

Jan 1, 1992

By Leo J. Miller

Sulphur deposits occur within the upper Salado and Rustler gypsum beds. The formation of a sulphur ore deposit requires large quantities of oil and /or gas, which must find a permeable pathway into the gypsum beds. The Permian beds weathered for 90 million years in an arid environment prior to the advent of a more humid climate at the beginning of the Cretaceous Period. The first Cretaceous rivers enlarged the sinkholes and caverns of the Karstified Permian terrain and deposited coarse conglomerates and sands into the subsurface gypsum beds. The resulting network of caverns and sinkholes, filled with permeable sediments, permitted the free flow of hydrocarbons through gypsum. All sinkholes and caverns infilled with Cretaceous sediments that have penetrated beds of gypsum are associated with sulphur deposits. The Castile gypsum lies directly upon the oil bearing Bell Canyon formation. Sinkholes and caverns filled with Cretaceous sediments occur in the lower Castile. Biogenic calcite and sulphur are adjacent to these sediments. However, faults assume the major role in generating the initial permeability, allowing hydrocarbons to penetrate the lower Castile gypsum. The largest faults are associated with biogenic calcite and sulphur for a distance of 250 meters up from the bottom of the Castile gypsum. It is apparent that two dynamic geological processes are generating permeability within the gypsum beds: (1) the Cretaceous sands decending with difficulty into gypsum and (2) the faults creating permeability in the lower Castile but losing energy through soft bed deformation in the overlying gypsum. Both of these sulphur ore controls are mappable, but another large sulphur deposit of the magnitude of the Culberson Sulphur Mine has yet to be discovered. It appears that massive sulphur deposits are associated with the largest scale examples of each system, that is (1) high densities of deep sinkholes and separately

Jan 1, 1992

By Brown K, Francis D

The Yallourn Open Cut Mine has recently commenced mining operations in the new East Field which will supply the 1450MW Yallourn W Power Station for the rest of its 30 year design life. The authors describe the design and implementation process followed during the rehabilitation of the areas disturbed by works associated with mining in the East Field. One area of the East Field, the old external overburden dump, has been of particular interest and is discussed in detail. A discussion on the fire protection considerations is included as these are critical and often misunderstood as being contrary to good rehabilitation design practice. Finally, the development of a master plan for the rehabilitation of the Yallourn Open Cut in general, incorporating the East Field work, is discussed.

Jan 1, 1992

By Jeffrey D. Swanson, Martin L. Smith

Smelterville Flats in Idaho's Silver Valley has been designated as a Superfund site due to metals contamination resulting from the use of the South Fork of the Coeur d'Alene river as a tailings impoundment earlier in this century. Tailings average in excess of 4% lead and zinc. Selective mining of highly contaminated zones is being studied as one of several possible remediation strategies. The first step towards remediation is the examination of the stratigraphic, geochemical and spatial characteristics of the site. These characteristics are related to appropriate sampling protocols and exploratory sample grid design. Special problems involved in the geostatistical analysis of tailings are emphasized.

Jan 1, 1992

By B. A. Hillman

Silicon is the second most abundant element on earth, exceeded only by oxygen. Silicon dioxide forms a crystalline structure of repeating SiO2 molecules which form characteristically hard, durable crystals. As a result, crystalline silica is Ubiquitous in the crustal rocks, sediments and the mineral products derived from mining. An examination of the history of studies that identify silica as a human and animal carcinogen is presented in the context of the development of a public health policy in California. The implications for the cost of conducting aggregate and other mining operations in the state are discussed.

Jan 1, 1992

By Jaime Huidobro, Mervin Austin

The effect on an explosive column of the sharp transient stress waves generated during the earlier detonation of adjacent blastholes is of paramount importance to explosives users. Some explosives will sympathetically detonate under these stresses. Others may suffer a transient desensitization, arising from a temporary increase in the density of an explosive beyond certain limits and persisting until the explosive mass relaxes back to the original density. Some explosives are so adversely affected by these stresses that the product suffers immediate and permanent loss of sensitivity. These effects can be clearly seen while blasting in tough conditions such as burn cuts or wedge cuts and in materials, such as coals, that propagate shock waves well.

Jan 1, 1992

By Y. Guan

The dissolution behavior of copper and gold from their pure state and from Au/Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the composition of the alloys, stirring speed of the disc, concentration of lixiviants and temperature on the overall dissolution kinetics has been studied. Gold/copper alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and 25, respectively. The dissolution behavior of these three alloys was compared with that of pure gold and of copper under the same chemical conditions. In general, the dissolution of copper and gold from alloys is partially controlled by surface chemical reaction and largely by mass transfer.

Jan 1, 1992

Shear strength testing of rock discontinuity surfaces has been undertaken at a considerable number of open pit gold mining operations in Western Australia, as part of geotechnical studies of pit wall stability. These mining operations are located in geological settings that are typified by highly weathered and/or chemically altered rocks that contain significant structural fabric in which accurate and representative measurement of shear strength is essential.Little of the published rock discontinuity shear test work and back-analysis of failures has been conducted on weathered discontinuity surfaces, at low normal stress levels which are comparable to Western Australian conditions. Available shear strength data are reviewed and the following aspects of shear strength testing are considered:ò the need for shear strength test work and the amount of testing required;ò review of laboratory testing methods and the quality of the results; ò presentation of the test results;ò discussion of the shear strength failure criteria; ò interpretation of the test results;ò summary of test results for a variety of rock types, degree of weathering and discontinuity surface conditions;ò a review of laboratory and field shear strength data to illustrate the amount of variability that can occur; andò a monitoring strategy is proposed to manage the uncertainty associated with discontinuity shear strength.

Jan 1, 1992

By Douglas J. Piper

On reflection of certain overall circumstances which have pervaded the gold mining industry, it appears useful to point out some specifics which the writer hopes will improve the potential for success in the application of hydraulic dredges to gold mining activity. I will, prior to entering into that discussion, comment briefly on rule of thumb for the application of the three types of equipment. The three are bucket line, bucket wheel and drag line dredges. From a standpoint of high volume movement over a short distance, between 50 and 300 feet, the drag line dredge is historically the most cost effective type of machine to be utilized if bulk excavation is the single driving consideration. It is typical for this sort of equipment to operate in the 10 to 30 cents per cubic yard range, however, cost of operation is not the sole consideration. Typically the drag line mixes and remixes the material which it excavates. In the event that gold recovery is the object of the exercise, a strong potential for loss of the valued mineral exists. Additionally, drag lines do a poor job of bottom cleaning, particularly if there is a ridged or creviced bottom which must be cleaned and in some cases partially removed to assure recovery of the highest percent of valuable ore. The bucket line dredge has, until recently, been considered an extremely cost effective device. However, the high cost of manufacture of this type of equipment has mitigated against its use in the majority of

Jan 1, 1992

By Nixon J

Open pit mining began in 1978 at the Woodlawn base metals deposit. For its ten years as an open pit the mine was financially unsuccessful as a combined result of difficult metallurgy and industrial unrest. In 1985 CRA bought out two American joint venturers with a view to going underground and a prerequisite to expending capital on developing an underground operation was to improve the industrial climate, work practices and mining methods.Following feasibility work, continuous production from the underground mine began in 1986 using mechanised cut and fill methods and a workforce trained under a multiskilling program. Men with no previous underground experience were trained by supervisors with backgrounds as miners to undertake all the work that is required with increases in skill levels being rewarded with increases in pay.

Jan 1, 1992

By Andrew L. Mular, Robert P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and success- fully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop set points as required in real-time. From its commissioning in November, 1989, to the end of the mine 's operation in June, 1990, it was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.IntroductionExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. ES proponents make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, an ES should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988)detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1992

Aurum Reef Resources is a provincially owned unlisted public company which holds a number of prospecting licences over Otago hard rock historically active minesites. The Bullendale Licence 31 1845 was applied for in 1985, granted 1991, including a DoC special condition allowing re-opening of the historic workings. The underground workings were commenced in 1862 and up to the mine's closure in 1906 some 40 000 ounces were produced at an average grade of 15.5 g Au/t. The purpose of the summer 1991 work programme was to enter the workings in an attempt to observe and sample the mullock between the lodes operated by the early miners. This objective was achieved on the third attempt. Samples were taken and subsequently a contract geologist resampled the workings and prepared a report indicating the Bullendale lode zone to be generally mineralised. Mullock interlode and schist foot-wall consistently returned assays over 0.5 g/t.

Jan 1, 1992

By Stephen J. Hales

State-of-the-art Resistance Spot Welding (RSW) equipment has the potential to permit adaptive feedback through recent advances in computerized process control. The initial step toward achieving this goal involves assessment of the effect of specific variables and the interaction between these process inputs on spot weld characteristics. This investigation addresses this issue through the application of Taguchi methodology to understand and refine a RSW schedule developed for joining of two dissimilar aluminum-lithium (AI-Li) alloys of different nominal thickness. The experiment was designed to establish a hierarchy of inputs with respect to each 'other, and to determine the significance of these inputs with respect to experimental noise. Valuable insight was gained regarding the interaction between process variables and the effect of certain equipment-related changes. In spite of a decrease in equipment performance, an improvement in the maximum strength attainable for defect-free spot welds resulted from the application of the statistical experiment.

Jan 1, 1992

By P. J. Kientzler, Y. C. Lo

The current study is concerned with the analysis and attempt at simulating the product size distributions obtained from a vibrating ultrasonic device. Systematic experiments of comminution were performed with natural sizes as well as monosizes in order to understand the breakage behavior of the device. A precise analysis of the device's breakage performance in the case of fine grinding of alumina samples will be presented. Initial steps to model the breakage events using a detailed mathematical algorithm will be discussed.

Jan 1, 1992

By M. David Monroe

Getting the best match between truck and haul road requires examining the cost effects of many factors. Most mines use a bottom line measure based on cost per ton of material moved. This measure focuses on the two components of truck haulage cost per ton: productivity (or performance) and operating cost. For specific tasks, productivity can be measured or predicted using either field measurement or modeling. Individual tasks can be combined to provide a larger scale, longer term net figure for total mine output. True cost is more difficult to capture. Factors are time- and task-oriented and can be influenced by a summation of factors over a truck's lifetime. For example, "allocated" costs, such as owning (depreciation) and some repair costs, are spread over long periods. Items such as fuel and tires can be tied more directly to certain tasks. This article focuses on the more direct, task-oriented factors that affect truck productivity and cost. Major factors The relationship of haul roads and trucks means that each must be examined separately to isolate the most important factors affecting performance and cost. There are many factors but the most important are:

Jan 1, 1992