Search Documents

By R. A. Jankowski, J. D. Potts

Four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner section averaged 0.59 and 0.26 mg/m3, respectively. The stageloader/crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feederbreaker contributed 0 to 0.2 mg/m3 of dust. A 1000 ft (305 m) increase in belt entry length or a 200 to 500 tons/shift (181,000 to 454,000 kg/shift) increase in production resulted in roughly a 0.1 mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By Sparrow G. J

In a recently completed AMIRA project, 20 samples were searched for gold mineralisation using the automated location facility (ALF) for rare phases on a scanning electron microscope in the CSIRO Division of Mineral Products, Melbourne. The samples were submitted by mining companies in Australia, and Papua New Guinea, and included crushed ore samples, cyclone overflow and underflow products, a flotation concentrate, and 12 tailing samples. Their gold contents ranged from 600 to 0.2 g/t An. Native gold and gold minerals including a gold telluride, gold-silver tellurides, and a gold bismuth mineral, were located in the samples as free grains and associated with other minerals such as pyrite, magnetite, hematite, ankerite, copper sulphides, silicate minerals, and quartz. In the highest grade samples, both micron sized and 200 ¦m grains of gold were found with ALF. It would be difficult to locate such d wide size range of gold in a manual search. Gold mineralisation was located in the tailing samples assaying 0.4 g/t An and higher. In several tailing samples coarse grains of native gold over 40 p.m in size were located. One grain was estimated to have contributed 40 per cent of the gold in the sample. As well as locating gold mineralisation, the ALF examination resulted in the identification of uranium, mercury, and bismuth minerals in the samples. Knowledge of the distribution of these minerals in processing streams could be important in the operation of a concentrator.

Jan 1, 1992

By A. J. Paul

Traditionally, 16"/50 caliber projectile shells have been fabricated from forged steel. The Naval Surface Warfare Center (NAVSWC) has determined that cost savings of approximately 60% (-$4.7M/year) as well as improved shell fragmentation can be achieved by casting these shells from austempered ductile iron. One of the technical concerns arising out of this material substitution is the role of the casting process in controlling the quality of the cast shells. Optimizing the process through proper orientation of the mold, placement of chills, superheat, etc., can minimize shrinkage porosity and, consequently, flaw size. For this purpose, the mold filling and subsequent solidification of the projectiles was simulated using a 3-D, fully transient, coupled fluid flow and heat transfer model based on finite differences. Several casting orientations were investigated and the casting parameters were varied to optimize the process and minimize casting defects. A comprehensive software tool, which was developed using state-of- the-art visualization techniques, has been used to analyze the process of casting. Emphasis is placed on the use of this visualization tool as an aid to the foundry engineer for process optimization.

Jan 1, 1992

By Gordon A. R

The effect of various types of solid carbonaceOlls reductants on the rate of fuming of zinc from lead blast furnace slag was investigated at I250°C.The results of the laboratory experiments indicated that the rate of removal of zinc from slag depended primarily on the volatile matter contents of the reduclants. The effects of fixed carbon, moisture and ash contents were less significant.

Jan 1, 1992

By Calvin Konya, Janos Foldesi

A bridge over a main line railroad system was scheduled for demolition. The bridge was made of reinforced concrete and spanned three mainline railroad tracks which could not be shut down due to blasting or demolition. To further complicate matters, the mainline tracks had high tension power lines running above the tracks, but below the bridge. These high tension wires provided the electricity for electrically powered trains. The tracks could not be damaged or disrupted, nor could the power line be broken.

Jan 1, 1992

By Randall M. Wheeler

The measurement and analysis of blast-induced ground vibrations are more complex than ever before. This is primarily due to the advancements made in microchip technology, mass storage utilities and the computer, which have allowed us to reduce and analyze data in a matter of moments instead of days. Terminologies such as Fourier transform, response spectra, cross-correlation, convolution, deconvolution and half-length frequency, etc. mean little to anyone except those who are experts in the field. A little understanding of the basic concepts behind vibration effects can help a beleaguered end-user feel more confident about what their measurements really mean.

Jan 1, 1992

In recent years the use of directional drilling has become increasingly popular in several applications. These include shaft pilot holes, exploration drilling, mine service holes and drilling beneath surface structures and obstacles. The prime objectives are to increase accuracy and reduce time, cost and environmental disturbance.

Jan 1, 1992

A Sun SPARCstation based computer network is utilised to store and process mining data at the Macraes Gold Mine. Techbase and Medsystem software running on the SunOS unix platform is used to generate all data plans, sections and other design data required on a daily basis to run the mining operation. The Macraes site is regarded as a fully integrated site where all geological, grade control, exploration, orebody modelling, resource estimation, pit optimisation and mine design is undertaken on site by MacraesÆ professional staff. The methodologies employed are regarded as æstate-of-the-artÆ where computerisation allows the rapid and efficient evaluation of large quantities of mining data by a handful of professional personnel. Ore reserves are estimated using an indicator kriging method and roving cone pit optimisation, a complex process that would not have been achievable in pre-computing days.

Jan 1, 1992

By T. C. Page

The Yarnell gold depoSit, located in the Weaver mining district of Yavapai County, Arizona is found within a structurally controlled, hydrothermally altered zone that occurs within a 1700 Ma granodioritic intrusive. Both potassic and sericitically altered rock that occur around and above the low-angle northeast striking Yarnell fault are known to host economic gold mineralization; a wider envelope of weakly-propylitic alterred rock also occurs in this area. During mineralization, strong sericitization accompanied several stages of quartz ± adularia veining, stockwork formation, and localized silicification and potassic replacement, in association with deposition of specularite, pyrite (now oxidized), and gold. The footwall of the fault is also sericitically altered but poorly mineralized. Mineralization along the Yarnell fault continues both northeast and southwest from the main deposit although the thickness of the zone and associated alteration envelope diminish away from the orebody. A sample of undeformed illite taken from the Yarnell fault zone was K/Ar dated at 69 ± 1.6 Ma; this date reflects a minimum age for both mineralization and latest movement on the fault. Gold mineralization is accompanied by modest increases in Ag, As, Cu, and Mo content. Both CO2-and H20-rich fluid inclusions were studied and suggest mesothermal pressures and temperatures of formation for the deposit.

Jan 1, 1992

The capacity of chlorine based solutions to rapidly and effectively dissolve coarse gold in oxide ores is well established. The inherent advantages of chlorine are high dissolution rates (10 - 100 times those of cyanide), and low cost. The high dissolution rates mean that coarse or poorly liberated gold may be dissolved over relatively short periods and hence ore particle size may cease to be such a critical factor. The cost of size reduction to allow adequate gold liberation in order to achieve an adequate gold recovery is less of a consideration when using chlorine than in traditional plant or heap leaching cyanide-based treatment systems.Because chlorine based solutions capable of dissolving gold evolve an unpleasant vapour phase with the potential for significant chlorine losses into the atmosphere, traditional heap leaching with active solutions being sprayed onto prepared heaps is not possible. The ore must be covered and the solution may be introduced beneath that cover through prepared injection `wells' and recovered through production 'wells'. The pit is flooded with active solution beneath an overburden or cover with the solution migrating from the injection 'wells' to the production 'wells' over a period of around five - ten days.

Jan 1, 1992

By Lon D. Santis

This paper reports on an evaluation of the safety characteristics of short lead, 5 centimeter (cm), Magnadet1 detonators. The Magnadet initiation system uses magnetic induction principles to transfer electric energy from the firing line to the detonator without a physical connection. This study was initiated because the Magnadet initiation system represents a new technology and the Bureau is interested in ensuring that no potential safety hazards are introduced into the nation's mining environment. The Magnadet system and its proper use are described along with a discussion of how it works. The potential hazards examined are: stray current from mine service power, lightning, DC current, static electricity, and radio frequency transmissions. Tip strength is also evaluated. Experiments were conducted to evaluate some hazards and theoretical methods were used to evaluate others. The results showed that the Magnadet short lead initiation system does not exhibit any unusual safety hazards. The new system is at least six times as resistant to common hazards as currently used electric initiation systems, so long as the insulation is intact.

Jan 1, 1992

By Glenn Ludwig, Stephen H. Chung

Fragmentation has a direct impact on mine costs and productivity. Computer programs have been developed to calculate fragmentation using data on the properties of the explosive, the characteristics of the rock, the rock mass and the blast pattern. While computer models can yield good data, conclusions must be verified. Fragmentation assessment, muckpile surveys or high speed film analysis of rock mass movement are some of the techniques that have been used to confirm blast results. Digitizing photos of the muckpile is now the most common method to assess fragmentation. But it has some drawbacks. Although automatic electronic imaging equipment speeds up the process, the results depend on the photographs. Shadows will distort results. High resolution, black-and-white prints are essential.

Jan 1, 1992

By Thomas Oberndorfer

Recent publications indicate that there is a rising interest in the field of mining method selection, and increasing efforts are being undertaken to develop satisfying solutions. Yet, computer assistance for mining method selection (MMS), or in other, terms assistance in the (pre-)feasibility state of a project, still lags behind the computer application in other mining activities. This is true for research as well as for application. This paper is intended as a contribution to the development in computer-assisted mining method selection, and focuses especially on underground hard-rock mining. It is structured in four main parts. The first deals with general aspects of mining method. selection within the process of mine planning, and with problems and requirements which derive from this specific situation. In the second part some numerical MMS-approaches hitherto published are briefly introduced, and investigations on these approaches are discussed. Based on .these experiences, in the third part an analysis of the complex system MMS is presented. It focuses on heuristics, influencing factors, objectives, assessment-routines and mining methods, and emphasizes the essential necessity of a profound mining method description (MMD) specially developed for the requirements of MMS and numerical processing. Accordingly the fourth part of this paper presents a mining method description model developed at the Department of Mining Engineering, Montan-University Leoben (MUL), Austria. It describes the consequences of the investigation, in particular the new mining method description model, on 'the design of a MMS-system. The paper closes with a outlook on the possibilities of an successful MMS-system being realised.

Jan 1, 1992

By Charles Joyce, William C. Burkle, Dan Murphy

Rare indeed has a major cross country natural gas pipeline met and surmounted such obstacles as the Iroquois Gas Transmission Line from Canada to Long Island, New York. Of the 370 miles long length a fair estimate has been that 1/3 or 122 miles were across rock country. Spread One, Four and Five were particularly difficult. If is estimated that over 75% of the required blasting was on those three spreads. The term "spread" goes back to the old term of describing a ranch.

Jan 1, 1992

By Wayne A. Ericson, Kirk S. Davis, Cornelis Winkler

BCI has developed a chemical process known as Ecophos® for the multi-industrial Pine Level Project in DeSoto County, Florida. Approximately 85 percent of the phosphogypsum at Pine Level will be converted to a very clean gypsum. The remaining 15 percent, including impurities plus some quartz tailings sand, constitutes what is termed redigestion solids. BCI has developed an alternative to the practice of disposing phosphogypsum in large above-ground impoundments. The proposed disposal method consists of mixing the redigestion solids with clays and reacting the mixture (leached tailings) with lime prior to disposal into the mine excavations as a reclamation soil material. Leachate water quality testing using lysimeter equipment indicates that the pore water associated with neutralized leached tailings meets maximum contaminant levels set for the drinking water standards of radium and selected primary metals.

Jan 1, 1992

By J. E. Chilton

Methanometers with catalytic heat- of-combustion sensors used in coal mines today will read low for flammable gases when oxygen (0,) concentrations are low or when methane (CH,) concentrations are greater than 10%. Thus, these methanometers may not be reliable during operations such as fire fighting or recovery of sealed mines. The U.S. Bureau of Mines developed a total flammable gas detector (TFGD) to measure CH, at concentrations up to 100% and to measure flammable gases in low 0, concentrations. This paper describes the operation and construction of the TFGD and discusses measurements of flammable mine gases obtained from a mine in western Pennsylvania.

Jan 1, 1992

By C. R. Edwards

"Since the first commercial extraction of uranium in the early 1940s, the range of feasible process alternatives has greatly increased. This paper reviews process options to reduce extraction costs, improve efficiencies, effect safer operations, and lessen environmental impacts. Equipment and processes used in the past, in use now, and that could be considered for future use are described.BackgroundTwo billion years ago life on earth consisted solely of single celled creatures of the simplest design (Gould 1989). Incredible as it may seem, uranium fission reactors were operating then also. In what is now western Africa, a series of natural reactors were fueled by rich uranium deposits in contact with underground rivers. Water from the rivers provided the moderator necessary to sustain the nuclear fission chain reaction. These primordial reactors ran down after about 600 000 years (Ontario Hydro 1989).Because it is ubiquitous in the earth's crust, humans have always been in contact with uranium. Mining of uranium, albeit not intentional, is ancient ; uranium minerals were embedded in ore veins mined for metals such as silver and copper.Uranium was discovered in 1789 in Berlin by an apothecary, Martin Heinrich Klaproth, who named the element after the recently discovered planet Uranus. The metallic element uranium, as opposed to its compounds, was extracted in 1841 by the French chemist Eugene-Melchior Peligot. The atomic mass of uranium was calculated to be 120, but the Russian genius Dmitri Ivanovich Mendeleev (famous and welcome everywhere except in Russia, where his liberal politics were detested by the Tsar), found this did not fit into his periodic table, and submitted a value of 240. Mendeleev was close; the exact atomic mass is 238.029.Henri Becquerel's detection of the radioactivity of uranium in 1896excited scientific study of the metal, but virtually no practical use was found for uranium outside of a minimal consumption as a colouring agent for glass and ceramics. Scientific interest intensified in the 19305. In 1933 Leo Szilard patented the concept of the nuclear chain reaction. While walking to work on a fine fall London morning and mulling over the problem of how to release atomic energy, he was stopped by a red light. He stood in thought and conceived the notion of the neutron-activated chain reaction before the light turned green. The patent was filed in 1934, and Szilard assigned it to the British Admiralty in order to keep it secret, in an honourable but ultimately futile effort to prevent the misuse of science (Bronowski 1973)."

Jan 1, 1992

By Ray Y. Lin

Chemical vapor deposition of tungsten carbide on the surface of steel has been investigated at temperatures between 400 and 550C in an atmosphere containing tungsten hexafluoride, hydrogen and benzene. The tungsten fluoride flow rate was maintained at 20 ml/min. The hydrogen flow rate was at 100 ml/min. The benzene concentration varied from 1.15 to 5.56% in the reaction gas. It was observed that the higher the temperature, the faster the deposition rate for tungsten carbide. But the dependence of the deposition rate on the benzene concentration was not systematic. From the x-ray diffraction analysis, it was observed that W, W2C and WC are all presented in the coating. The amount of each phase presented in the coating depends on the temperature and, to a less extent, on the benzene concentration. The microhardness measurement has also been done for all CVD carbide coatings obtained in this study.

Jan 1, 1992

By J. Diao

In order to understand the flotation kinetic behavior of coal and associated mineral matter, a detailed investigation was conducted in a 2-liter Denver flotation cell using three high sulfur coals at three feed sizes, minus 28. 100 and 200 mesh. Subsequently. the flotation products were sieved into different size fractions and analyzed for their ash and pyritic sulfur content in order to delineate the effect of particle size on the rate at which each constituent floats. The results were tested with several different flotation kinetic models and the best model for coal was then chosen. The flotation rate constant and the ultimate recovery calculated from a kinetic model were used to delineate the effect of particle size, collector (dodecane) and frother (MIBC) dosages on the flotation kinetics of coal, ash and pyrite.

Jan 1, 1992

Jan 1, 1992