Search Documents

By Steve P. Signer

A study of rock support interaction mechanics was conducted by the U.S. Bureau of Mines at the Jim Walter Resources No. 7 Mine, Brookwood, AL. Bolt loads and entry deformation were monitored at four sites in a tailgate roadway. Two sites were areas supported by fully grouted resin bolts, and two sites were supported by tensioned bolts that used resin-assisted mechanical anchors. The yield capacity of the tensioned bolts was 37 pct higher than that of the grouted bolts. To monitor loads, instruments were mounted on 16 bolts, which were installed during entry development in the standard bolt pattern. Additional instrumented bolts were installed as supplemental support just prior to the headgate pass of the first longwall. Instruments to measure roof movements included three-point roof extensometers and convergence stations. Readings were taken during section development and as each longwall panel passed the test area. The fully grouted bolts showed localized loads that were higher than loads on the tensioned bolts; however, overall loading magnitudes were similar. Many sections of the fully grouted bolts passed the yield point of the bolt steel (98 kN or 22,000 lb). However, the maximum strain measured at any loca¬tion was 50 pct of the ultimate strain, and there was adequate bolt length to transfer the high loads into the rock. Significant bending was detected at many points along the length of the bolts and seemed to be the most significant mechanism in support-rock interaction. Loads on the tensioned bolts did not exceed the yield point of 160 kN (35,000 lb). Entry deforma¬tion, supplemental bolt loading, and general entry degradation appeared to be slightly less at the tensioned bolt sites. Local geology and in situ horizontal stress were also observed to affect con¬ditions at the test sites.

Jan 1, 1993

The LeadtZinc Concentrator at Mount lsa treats all the lead-zinc-silver ore from the Mount Isa Mine and some of the ore from the Hilton Mine. This concentrator was commissioned in June 1966 and total lead-zinc-silver ore treatment was transferred from the Mount rsa's original No 1 Concentrator in May 1967. Plant capacity is around 5 x 106 t/y.There have been three phases of major plant modifications since commissioning:1. replacement and upgrading of the flotation section in 1979; 2. upgrading of the crushing plant and installation of a heavy medium hydrocyclone plant in 1983 for ore preconcentration, and; 3. doubling ball milling capacity and a further upgrading of the flotation section in 1992.Other developments have included the installation of flotation columns and Jameson cells.The evolution of milling practice since 1955 has been reported by Davey and Slaughter (1970), Bartrum, Dobrowolski and Schache (1977), Fiedler and Munro (1984) and Espinosa-Gomez el al (1989).Lead concentrate is smelted in Mount Isa while zinc concentrate and bulk concentrate (locally called Low Grade Middlings or LGM) are railed to Townsville and shipped to custom electrolytic zinc plants and ISP smelters.

Jan 1, 1993

In this, the centennial year of The Institute, it is appropriate that the history of the Institute in New Zealand be recorded. I am indebted to John Dew, compiler of the centenary publication æMining People A Century - Highlights of the First Hundred Years of The AusIMM 1893 - 1993Æ, for many of the early historical references in this paper. In July 1892 the Amalgamated Mining Managers' Association of Australasia held its annual conference in Ballarat, Victoria, Australia, when it was suggested by the delegate from Broken Hill that the time had arrived for the establishment of an Australasian Institute of Mining Engineers. Resulting from this meeting at Ballarat, a Provisional Committee was formed at Broken Hill with the object of forming The Australasian Institute of Mining Engineers having the following objectives. To promote the arts and sciences connected with the economic production of the useful minerals and metals, the welfare of those employed in those industries by means of meetings for social intercourse, and the reading and discussion of professional papers with the circulation by means of publications amongst its members and associates the information thus obtained.

Jan 1, 1993

By B. Mishra

Calcium and lithium gallides have been synthesized by powder metallurgy techniques in the stoichiometries that can be used as reduction alloys for the Rocky Flats Plant Salt-Scrub (SS) process. The SS process is performed to recover valuable metals from salts generated in the electrorefining and the molten salt extraction processes. Combustion synthesis has been optimized for variable heating rates up to the reaction ignition temperature and for green densities of the powder compacts in terms of the ignition temperature and the exothermic heating of the product in an effort to develop LiGa and CaGaz alloys. The problems arising from the melting point and density differences of calcium, lithium and gallium have also been studied. The SS alloy compositions were produced by mixing, pressing and sintering the metal-powders. The efficiency of the intermetallic alloy, Ca-17 wt. pct. Ga, as a reductant and the effect of gallium on salt clean- up has been discussed. Measurement of actinide recovery has been studied with cerium as the surrogate for the actinide metal. The development of an alloy for SS reduces a major contaminated waste disposal problem besides recovering the valuable reactive metal.

Jan 1, 1993

The Barra Mine was the most significant mine of Australia's earliest mining era, which took place in South Australia between 1841 and 1851, the decade prior to discovery of gold in eastern Australia. Between 1845 and 1860, Barra was the largest metalliferous mine in Australia and employed up to 1000 men and boys, most of them Cornish.""Today the site is also important in a physical and archaeological sense as it contains extensive remains of mining and processing operations of the period 1850 - 70. Most significant are three cnginchouses which housed Cornish beam engines.

Jan 1, 1993

By C. J. Myers, D. L. McKinnon, A. A. Dasys

In 1988, the National Institute of Occupational Health and Safety (NIOSH) published an information bulletin stating that whole diesel exhaust should be considered a probable carcinogen. Since then, regulations across Canada and the United States (Mine Safety and Health Administration, MSHA) have looked at appropriate exposure limits for underground mine workers. In Canada, an interim standard of 1.5 mg/m3 Respirable Combustible Dust (RCD) has been adopted by some provinces and is being looked at by others. MSHA is considering levels as low as 0.5 mg/m3 soot. Golden Giant, being aware of regulatory developments, decided to look at means of reducing diesel particulate on thier large production machinery. This machinery (LHDs and haulage trucks) is powered by Detroit Diesel 71N Series engines and is used to produce 3000 tonnes of ore/day with a longhole mining technique. Having looked at the various control technologies, it was decided to evaluate the potential of using diesel particulate filters with a copper-based fuel additive for regeneration (the process by which collected particulate is burned off). This paper outlines the control technology used and the results of the field evaluation indicating the benefits to the underground mine worker.

Jan 1, 1993

By Xuan Cheng

The electrochemistry of sulfide mineral flotation is reviewed with particular emphasis on galvanic interaction among minerals and grinding media, and its relevance to flotation of complex sulfide ores is discussed. Surface alteration due to galvanic interactions among chalcopyrite, pyrrhotite and mild steel is analyzed in terms of voltammetric and chronoamperometric studies on individual minerals and through galvanic current measurements in 2- and 3- electrode combinations. The results are related to laboratory flotation behaviors of chalcopyrite-pyrrhotite mixtures simulating copper-nickel bearing Duluth gabbro.

Jan 1, 1993

By C. D. Harrison, G. S. Stallard

The 199O Clean Air Act Amendments specify national objectives for reducing sulfur dioxide emissions from coal fired power plants. System-wide reductions can be achieved by combining various emissions control technologies and allowances, or compliance credits, that can be purchased, sold or traded. As part of the Coal Quality Expert development project funded by the US Department of Energy and the Electric Power Research Institute (EPRI), Black & Veatch has developed an interactive computer tool, the Acid Rain Advisor (ARA). Through this program, integrated, system-wide compliance plans are generated by comparing the costs and emissions reduction benefits of emissions allowances and various SO2-control technologies (coal cleaning, fuel switching, scrubber retrofits, etc.)

Jan 1, 1993

By Huajun W, Long LZ

The composition of fly ash and formation mechanism of cennospheres are introduced in this paper. The signification of using this potential new mineral processing resource is emphasised. The beneficiation properties of the components of fly ash, such as susceptibility, specific gravity, size, shape and flotability etc have been examined in detail. A technique was designed to process fly ash from the XiGaoJing power plant in Beijing, and a flowsheet is also presented. Flotabld cennospheres, magnetic beads, sinkable beads, carbon and advanced pozzolamics can be obtained as separate products through this flowsheet. It is emphasised that the beneficiation of fly ash is an efficient means of totally utilising the resource. Examination of the products show that they have good physico-chemical properties. Possible areas of their application are also Suggested.

Jan 1, 1993

By M. Timberlake, A. J. Jonaitis

"The DENVER Tube Press is a simple, high pressure (1500 PSI (100 bar)) filtration unit, developed for processing difficult-to-dewater materials and to produce a handleable filter cake and clear filtrate product.Lab and Pilot testwork conducted in Australia on coal fines (55-70% -35 micron (400 mesh)) have shown that total moisture contents of less than 20% are consistently achieved in the final cake products from the Tube Press.currently, these coal super fines are sent to waste due to uneconomical mechanical dewatering methods, which were only able to reduce total moisture levels in excess of 30%. Calculated, throughput rates for the 500 series Tube Press exceeded 1700 kg/hr (3750 lbs/hr). Feed solids concentration requirements are between 45 and 50% to achieve these results.INTRODUCTIONThe DENVER Tube Press is an automatic membrane high pressure filter press, which operates at hydraulic water pressures up to 1500 PSI (100 bar). The Tube Press was developed in the late 1960's by Charlestown Engineering, st. Austell, Cornwall, England, formerly a division of English China Clays, Ltd., to address more effective methods of moisture reduction of micron-size china clays. The Tube Press reduced moisture sufficiently to produce a hard surface-dry, handleable cake and clear filtrate discharge, which was recycled into the process. This development work was conducted using a 200 Series Tube Press (200 mm diameter x 2500 mm long filter surface)."

Jan 1, 1993

By Fernando JAS Barriga

The world-class Neves-Corvo deposits were intersected by drilling in 1977. They occur in the (Carboniferous) Iberian Pyrite Belt (IPB), Western Europe&apos;s largest stock of base metals (see Bamga, 1990, in Dallmeyer RD, & Martinez E, eds, Pre-Mesozoic Geology of Iberia, Springer-Verlag). Massive and stringer sulfides in the area sum up to about 200 Mt (109 kg), in five main orebodies (Neves, Corvo, Graca, Zambujal and Lombador). They include unique, extremely high grade copper and tin ores ( - 33 Mt Cu ores, -7.5% Cu, and -4 Mt Sn ores, -2.6% Sn, - 12.5% Cu). Also present are -50 Mt polimetallic ores (-6% Zn, 1.2% Pb, 64 ppm Ag). The remaining are relatively low grade pyritic massive and stringer sulfides (Cu < 2%. Sn < 1%, Zn equivalent < 4%). The geological setting is one of bymodal submarine volcanism, with predominant felsic, explosive volcanism and associated sedimentation (detrital and chemical), which took place on a shelf-facies, quartzite-phyllite basement (of Upper Devonian age). The plate tectonic setting has been the object of much debate. Current interpretations favour that the IPB volcanism took place in a tensional fore-arc region, associated with oblique subduction and collision (Silva et al., 1990, same volume as above). At Neves-Corvo there are many different ores, that may be grouped in four main types: fissural (at the base), breccia, massive (intermediate) and "ruban6 " (at the top). Fissural ores seem to correspond to stockworks in contrasting types of host rocks (gray to black shale, sericitic, chloritic and graphitic, and light gray volcanic rock). Massive ore may contain significant shaly gangue, at the base of individual orebodies, and silica-rich (cherty) varieties towards the top. The more sulfide-rich varieties predominate, and are usually well banded.

Jan 1, 1993

By Owen Owens, W. P. Armstrong

The process of arriving at the size and grade of: (a) a newly-discovered body of mineralization, (b) a potential ore resource, (c) an orebody proposed for mining, or (d) the ore reserves in a mine, requires fundamental geological, and geometrical determinations as well as physical and chemical analyses. This paper outlines geological and geometrical features considered critical, in the authors&apos; experience, in realistic reserve determination. These are discussed under the headings "The Four Cs". They include the Character, type or nature of the mineralization; the Continuity of various types of mineralization in the deposit; various key concerns in the Calculation besides the mathematics; and the Classification section which refers to basic considerations in classifying a mineral estimate. It is suggested that the responsibility for the calculation of a Resource or Reserve should be that of a geologist experienced in the ore type under review. Further, it should be the responsibility of the board of directors of the company owning the deposit to ensure that a sufficiently experienced person is chosen to carry out the process.

Jan 1, 1993

By Gerrit V. R. Goodman, Charles D. Taylor

A technique was developed to determine the fraction of air recirculated from the scrubber exhaust toward the face and the fraction of gas captured by the scrubber. To determine these two values, a series of tests was required. In the first test, gas was released at the face area and concentrations measured at the scrubber exhaust. In the second test, gas was released directly into the scrubber with concentrations again measured in the scrubber exhaust. The simultaneous solution of two independent flow expressions gave values of recirculation and scrubber capture. A series of tests was conducted with various combinations of scrubber flow, curtain flow, setback distance, and machine location. Statistical analyses then were conducted to determine those factors which influenced the levels of scrubber recirculation and scrubber capture in a deep cut. INTRODUCTION As cutting depths increase, the trend is toward the use of blowing face ventilation systems. With these ventilation systems, the potential exists for recirculation between the scrubber exhaust and the intake air stream. One concern is that methane gas, having been removed from the face area, is subsequently recirculated back into the intake airflow. Under these conditions, methane-laden air could be substituted for fresh intake air, leading to increased methane concentrations at the face. There is currently no standard for recirculation between the scrubber and intake airflows. The implied understanding of the Mine Safety and Health Administration (MSHA) is, and has always been, that any recirculation of ventilation air is unacceptable. To minimize recirculation potential, MSHA suggests that operators maintain scrubber and curtain flows within 0.47 m3/sec (1000 cfm) of each other. Given that recirculation may occur in some circumstances, the question arises as to how much recirculation constitutes a hazard for the face workers. Unfortunately, there is currently insufficient information to answer this. Emphasis must instead be placed on means to quantify the amount of recirculation between the scrubber and face area. Methods must also be examined to control this phenomenon. This paper presents a technique for quantifying recirculation and scrubber capture levels in a blowing face ventilation system. Several ventilation parameters are investigated to determine their effects on these levels. DEVELOPMENT OF RECIRCULATION EXPRESSIONS One way to measure airflow quantities at a point near the face would be to measure the gas flow rate Qgas, and gas concentration c at that location. The airflow Qair, would be simply the ratio of these two values, Qair, = Qgas/c. Although gas concentration values, c, can be obtained easily with existing gas monitoring equipment, it is more difficult to obtain gas flow readings, Qgas, at specific locations. To obtain these values of Qgas, another method was needed. Previous work in this area was conducted by Kissell and Bielicki (1975). However, the calculations in their model assumed a constant gas concentration in the region around the continuous miner. In a deep cut, it is questionable that gas concentrations would remain constant or uniform around the mining machine. The technique presented here does not rely on this assumption. It instead assumes that the gas concentration in the scrubber exhaust remains constant. A quantity of gas released at the cutting face either flows into the scrubber inlets or bypasses the inlets and flows around the off-curtain side (in this example, the right side) of the continuous miner (Figure 1). The fraction of the face gas that flows

Jan 1, 1993

The rapid growth of world civilisation will have a significant impact on the way humans live in the future. As the global population increases and more countries demand a higher standard of living, the world must provide more food and greater energy and mineral resources to sustain this growth. The difficulty of doing this is compounded by three broad trends: the conversion of agricultural land to development uses; the increasing urbanisation of the world&apos;s population; and growing concern for the maintenance and improvement of the environment, especially regarding global warming and the impact of population growth. Underground space utilisation offers opportunities for helping address these trends.

Jan 1, 1993

By Thomas C. Anderson, Terry Weiss

The Mount Gunnison No. 1 Mine of the West Elk Coal Company (wholly owned subsidiary of ARCO Coal) had secured contracts to provide low sulfur, high Btu steam coal to various utility companies. This called for the development of the B-Seam at the Mount Gunnison Mine located some 400 feet below the operating F-Seam workings being mined with conventional room and pillar techniques. The B-Seam, to meet production goals, will be mined by a new 600-foot longwall machine making a 13-foot high cut. American Mine Services was awarded a competitively bid contract to drive two 2000-foot, 13-foot by 16-foot slopes at -15 percent, sink a 16-foot diameter ventilation shaft 400 feet between the F- and B-Seams, install a 60-inch conveyor in one of the slopes, remove 7000 feet of existing conveyor and rehabilitate 7000 feet in two entries to accommodate the placement of the longwall machinery. The slope portals were located 7000 feet in by the surface portal. Unique to the project was the placement of work shops and other infrastructure 7000 feet underground with an entry height of 6 feet. The $7 million contract was completed in less than one year using a mix of permissible (Schedule 31) and standard (Schedule 24) LHD equipment, all pneumatic jumbos and shaft sinking gear.

Jan 1, 1993

The tankhouse of the electrolytic zinc plant at Nordenham is operating with a very high operating efficiency of 99 per cent. This has been achieved not only by strict control of the quality of the zinc sulphate cell feed solution but also by all the improvements in housekeeping in the tankhouse developed during the past years: aluminium cathode specification, cathode stripping cycle, edge strips, copper contacts, anode isolators, cell cleaning, fittings and washing devices. During 1987 to 1992 the casting department was completely remodelled in order to improve the quality of the zinc products, the safety of the operations and the flexibility. The remodelling includes the enlargement of the area for the casting shop, the storage buildings and the five casting lines on the same ground level. New lines for alloying products and for SHG25 kg zinc ingots have been constructed. The line for galvanising products has new equipment in some parts and the other lines have been modified.

Jan 1, 1993

By Howarth W. J, Sowerby B. D, Watt J. S

On-line analysis systems have found widespread application in the metalliferous mineral and coal industries. The continuous analysis and rapid response of these systems has led to improved control of mining, processing and blending operations, with increased recovery of valuable minerals and coal combustibles.The paper reviews developments in on-line analysis by CSIRO and Mineral Control Instrumentation Ltd which led to the award of the Australia Prize 1992. These commercialised systems analyse mineral and coal slurries; determine the ash and moisture contents of coal on conveyors, and the moisture content of coke on conveyors; and determine the carbon content of fly ash. These gauges are estimated to have resulted in productivity increases valued at $50 million per year to Australia.

Jan 1, 1993

By Peter Cain

Twenty years of research into the design of permanent gateroad support (packs) in coal mines have resulted in two methods of pack design based on engineering principles. The first, the detached block concept, is based on static loading of the support system by an hypothetical detached block. The second, the roof beam tilt concept, is based on the dynamic loading of the support system as the roof beam tilts over the roadway about a pivot point located in the rib-side. The roof beam tilt concept has been used on a number of occasions to design packs in a variety of conditions. However, recent work in the Sydney Coalfield of Cape Breton Island, Nova Scotia, has shown that design criteria based on the roof beam tilt concept in its present state of development are far from universal in application. After a review of published pack performance data, including detailed studies conducted in the UK, France and Canada, it was found that consideration of the mechanical properties of the roof beam produced a design criterion that fitted the available data. Modifications to the design process using the roof beam tilt concept are suggested for use in pack design. The work also revealed that current research in other aspects of coal mine ground control, particularly the areas of powered support design and subsidence prediction, may provide valuable information leading to major advances in this field. Such developments could also extend the application of the roof beam tilt concept to the design of pillar systems.

Jan 1, 1993

By M. Akram

Stability assessment of entry roofs is an essential precursor to all underground design. Both multi-seam interaction and longwall mining can subject entries to radical changes in the surrounding stress field. Such loading changes frequently produce instability and failure in the roof, floor and pillars. Roofs are shown to be vulnerable to stress-induced failures, particularly when the load is unsymmetrical. To predict the effects of changes in stress field, roof failure conditions under increasing loads were studied using finite element analysis and body loaded photoelastic models. A large range of geologic conditions were evaluated and incorporated into the model using Monte Carlo methods. Entry analysis using the model showed the roof to be particularly vulnerable to shear with the location of the failure site changing to meet loading and geologic conditions. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Based on this research a roof stability model SESAME was constructed for roof stability evaluation under specified loading conditions.

Jan 1, 1993

By R. D. Lama

This paper presents the results of a large scale trial of polycrystalline diamond picks (PDC) on longwalls with particular reference to dust control. Results from fixed position monitoring showed that PDC picks produced less respirable dust than tungsten carbide Point Attack picks. Dust generation at the longwall face was lower by 39 - 43%. Field trials also indicated that the life of a PDC pick to be at least 1460 tonnes/pick.

Jan 1, 1993