Search Documents

By Felicia F. Peng

Two modes of collector addition techniques are applied in the column flotation for cleaning ultra fine coal. The collector can be: 1) added directly into the coal slurry through the feed system; and 2) gasified collector and transported in the gas phase through the bubbles. Operating parameters of the column flotation were investigated through three phases of work plans for Pittsburgh No.8 seam coal. In present study, the column flotation using two modes of collector addition techniques were tested and compared. Ninety percent or higher combustible recovery can be achieved by using both methods. However, utilizing the gasified collector addition technique in column flotation has more potential than direct liquid addition technique to obtain the higher recovery at same collector dosage.

Jan 1, 1993

Some crystal chemical properties of several apatites from Brazilian deposits and occurrences were determined; the samples had different origins (igneous, metamorphic and sedimentary). The aim was to establish relationships to their froth flotabilities behaviour. Detailed X-ray diffraction studies were carried out, to determine precisely the unit cell parameters and the degrees of crystallinity of the apatite samples. A thorough chemical analysis of these minerals was also conducted. Microflotation studies were carried out, using sodium oleate and dodecylammonium chloride as collectors. The crystallinity levels were determined for all samples studied, with the establishment of a crystallinity index, which varied from 10.0 to 4.5, on a normalised scale. A marked dependence was observed between this crystallinity sequence and flotability; for both collectors, flotability dropped drastically for crystallinity indices lower than 8.0. Also, the low crystallinity apatites showed a decrease in floatability, for longer conditioning times.

Jan 1, 1993

By Robert P. Vinson

The U.S. Bureau of Mines evaluated a light-scattering technique for discriminating between spherical and nonspherical particles. This evaluation was a three-step procedure. The first step required collecting light-scattering data for a variety of particles. This was accomplished with a particle analyzer called the DAWN-A. The DAWN-A measured the scattered light intensities of individual particles at a forward scattering angle of 40°. These DAWN-A measurements of individual particles are called scattering signatures by the Bureau researchers. The second step in this evaluation was to calculate a sphericity index number using the scattering signatures produced by the DAWN-A. The sphericity index number can range from 0 to 1. A calculated sphericity index of 1 would show that based on the intensity of scattered light, the particle was a perfect sphere. The third and final step of this evaluation was the comparison of the calculated sphericity indices of the various particles. Comparing these indices made it possible to discriminate between the nearly spherical waterdrops and the nonspherical coal and rock dust particles.

Jan 1, 1993

By O. E. Humeniuk, A. I. A. Salama, M. W. Mikhail

"Performance testing of prepartion plants is referred to as plant audit. It evaluates plant performance under normal operating conditions and is aimed at improving yield through knowledge of actual process performance and interactions between different processes in a plant.This paper describes the program to evaluate the performance of several Canadian preparation plants. The performance test requires the planning of a sampling campaign that would include all circuits in the plant. Samples are analyzed to determine washing characteristics (screen and float-sink), ash and per cent solids of feed and products of separation units in the plant. Performance characteristics are established based on analysis and material balance. Specific recommendations can then be made to improve recovery, and identify and explain potential causes of apparent deficiencies.The objectives of the program are to reduce the cost of production by improving recovery of clean coal and, in tum, to reduce disposed tailings, establish baseline information on coal preparation plants performance in Canada, and define R&D work needed to optimize plant operation."

Jan 1, 1993

By Rubisov DH

This paper is related to the problems of the mathematical modelling of vibrating screening process and to predicting the screening operation results. The authors propose a model of screening based on the interpretation of granular material segregation on a screen surface as an instantaneous process. Results show an agreement with laboratory and pilot plant tests. Derived formulae can be used for screen sizing and screening result estimating.

Jan 1, 1993

By Taner Sumer, H Altay Guvenir

Fragmentation in rock quarries is tried to be achieved by changing the specific charge, drill pattern and bore hole diameters by different experts. This paper is a brief summary consisting of the utilization of practical experiences of the other group on cost optimization procedure that takes into account blasting, transportation and crushing as a whole process and optimize the cost by defining the optimum gelatin based explosives to be used as a main primer of anfo in three different limestone and granite quarries, with similar rock characteristics.

Jan 1, 1993

By M. A. von Below

Environmental activists have targeted the mining industry in an attempt to prevent development, which has resulted in the industry's becoming defensive and retro-active. This paper argues that mining managements should go on the offensive and champion the environment through leadership in environmental policy and research and development, rather than reacting to anti-mining campaigns. In the formulation of an environmental policy for the mining industry, a clear understanding of the concept of sustainable development is of paramount importance.

Jan 1, 1993

By Seshadri Seetharuman

The present paper summarises a series of measurements of the interaction parameter of oxygen in liquid copper with respect to a third element, e(M)o, where M is Mn, Zn, As, Se or Te which are common impurities in the liquid metal. The technique employed was the solid electrolyte galvanic cell method. The cell used may be represented as Pt, W or cermet / Cu-O-M // ZrO2 - CaO // AO, A /PT where AO/A represents a suitable oxide/metal reference. The measurements indicate that Mn and Zn interact very strongly with oxygen in liquid copper while, in the case of arsenic the interaction parameter is nearly zero. The behaviour of the elements Se and Te is unique with respect to oxygen interactions in copper bath. At oxygen levels, xo= 10-4 ? 10-5, the apparent interaction parameters are negative, comparable to that for sulphur. On the other hand, at lower oxygen levels, the results indicate that the interaction parameter values are positive. The results are discussed in the light of some of the theoretical models for solute interactions in liquid metals.

Jan 1, 1993

By D. R. Spears

The Bureau of Mines has investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed, and solids concentration on the kinetics of shear-flocculation. The results showed that shear-flocculation is a two-stage process. In the first stage, mean particle size increased rapidly in the first 1-2 min of reaction; in the second stage, an equilibrium was set up between the rate of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear-flocculation to occur and was dependent on solids concentration and collector dosage. This speed was the minimum necessary for particles to overcome the electrostatic energy barrier which kept conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1993

By Van Weert G

Ferrous chloride solution pyrohydrolysis is a successful IICI regeneration process which is carried out in either a spray roaster or a fluid bed. Pyrohydrolysis is not restricted to ferrous chloride only, every metal chloride can theoretically be hydrolysed. In practice, however, the conditions for ferrous chloride pyrohydrolysis differ from those of many non-ferrous metal chlorides eg zinc, lead and cadmium. Hence, a pyrohydrolyser could function as a ferrous/non-ferrous separator, eg an iron oxide and zinc chloride separator. Most pyrohydrolysers operate on solutions, in which case more than 50 per cent of the process energy is needed for heating and evaporating water. However, this disadvantage would be diminished by feeding a slurry to the reactor. Against this background it was decided to investigate the chloridisation of zinc ferrite which is an iron bearing solid with a non-ferrous impurity, and subject to processing and disposal problems. Synthetic zinc ferrite was chloridised in a tube furnace. The gas atmosphere in the tube furnace resembled that of a fluid bed pyrohydrolyser and consisted of HCI, 1120 and nitrogen. Gas composition, temperature, residence time and sample mass were varied. The experiments showed that complete (99.6 per cent) zinc extraction from synthetic zinc ferrite was possible in a simplified pyrohydrolyser atmosphere at 1100 K in four hours. The zinc ferrite was converted into gaseous zinc chloride, and hematite and magnetite solids. It was also found that zinc removal from the zinc ferrite lattice caused not only rccrystallisation of the zinc ferrite into hematite, but also hematite crystal

Jan 1, 1993

By Ralph H. Nafziger

The feasibility of smelting a Ni-Co-Cr-bearing laterite ore from southern Oregon was evaluated by the Bureau of Mines. The objective was to prepare a master alloy for subsequent stainless steel production. A mixture of the ore with suitable reductants and fluxes was smelted in a 50-lb-capacity single-phase ac electric furnace under sub- merged arc conditions. The smelting tests produced a metal in which most of the nickel was concentrated. High-chromium recoveries required an excess of carbon. The resulting metal alloys contain sufficient nickel for some stainless steels. Ferrochromium additions would be required to attain suitable chromium levels. This research was conducted under the Oregon Metals Initiative in cooperation with Walter B. Freeman.

Jan 1, 1993

By J. D. Miller

The sedimentary western phosphate deposits of Idaho, Montana, Utah, and Wyoming tend to be calcareous and generally carry a significant amount of dolomite along with collophanite. In some cases, such as the Smokey Canyon Mine, Afton, Wyoming, the ore will also contain mudstone, and in this case the aluminosilicate minerals (clay, feldspar, etc.) together with some dolomite are floated from the collophanite in column flotation cells with an amine in order to meet product specifications (31 % P205) (Service et al.). In other cases, such as the SF Phosphates Limited Mine, Vernal, Utah, the ore is treated by traditional fatty acid flotation of the collophanite with mechanical flotation cells (Weber, 1986). Preliminary tests have now been conducted to evaluate air-sparged hydrocyclone (ASH) technology for the flotation of western phosphate ore. For this preliminary study, samples were taken from the hydrosizer overflow stream (18-21 % P205) at the SF Phosphates Limited Plant in Vernal, Utah for scavenger flotation testing with the 2-inch ASH system in laboratories at the University of Utah. Selected design and operating variables are being studied, and the initial results show that satisfactory separations can be achieved by high-capacity ASH flotation at appropriate operating conditions. For example, with single-stage ASH flotation 80% recovery can be obtained with a scavenger concentrate grade of about 26% P2O5. These results are comparable to, or better than, those obtained at SF plant operations with conventional flotation cells and suggest that ASH flotation technology can be used to good advantage in the phosphate industry. Of course, research should be continued to consider other process streams, optimize the separation efficiency, and evaluate larger diameter ASH units.

Jan 1, 1993

By E. F. Paski

Geological materials are likely the most complex and challenging substances to quantitate by ICPOES (inductively coupled plasma optical emission spectroscopy). For complex materials having widely varying compositions, spectral overlap interferences govern detection and quantitation limits attained by ICPOES based analytical methods.

Jan 1, 1993

By N. L. Piret, R. J. Wesely, A. E. Melin, A. D. Zunkel

At the end of the sixties new iron precipitation techniques as jarosite, goethite or hematite brought about the new generation of electrolytic zinc plants, thereby terminating the multitude of existing neutral leach residue treatment schemes. Since the eighties, increasing environmental impact considerations urge the conversion of these contaminated waste generating precipitation processes to techniques which either produce environmentally acceptable residues or minimize their formation thereby generating iron-bearing byproducts. Technologies identified and economically assessed include the hematite process either suitably improved or with subsequent upgrading, the iron extraction process and the direct smelting of neutral leach residue to slag and fumed zinc oxide.

Jan 1, 1993

By Nickolas J. Themelis

The flash oxidation and smelting of mineral sulfides is a very prominent metallurgical achievement of the second part of this century. Its initial industrial implementation owes much to the work of Petri Bryk, in Finland, and Paul Queneau, in Canada. However, attempts to develop flash reduction pro- cesses, such as the reduction of iron oxide concentrates with hydrogen, have not yet been successful. The author, on the basis of experimental studies on both kinds of flash reaction systems, examines the respective rate controlling phenomena and the relative rates of flash oxidation and flash reduction.

Jan 1, 1993

By McDonald K. J, Flann R. C

A liquid phase sintering (LPS) process for preparing basket anodes from nickel powder has been scaled-up and the innuence of compact green density and sulphur content, as well as sintering conditions (period and syngas now.rate) on the perfonnance of anodes has been evaluated. The product anodes have been tested in an industrial electroplating tank. It is concluded that if anode residues are to be minimised, then with a sintering temperature of 960"C, compact green density needs to be as high as economically achievable (85 - 87 per cent density of solid nickel) and the sintering period approximately 40 minutes. With these constraints, if residual sulphur contents of anodes are to be kept as low as those of commercial anodes, then the sulphur content of the green compacts would need to be less than 1670 ppm. At the same time, it is also found that residual sulphur concentrations as high as 2000 ppm are beneficial to anode pcrfonnancc and not detrimental to the quality of the electroplate. The ability of the LPS process to produce marketable nickel anodes for the electroplating industry is clearly demonstrated.

Jan 1, 1993

By Chapman G. J

Mining operations require detailed and precise methods and procedures for the optimum selection of ore from waste. A fundamental procedure applied to achieve this selection is accurate sampling. The key parameter to accurate sampling is an understanding of the degree of heterogeneity of the key element contained within a sampling mass. This paper will describe the methods applied for the calculation of the fundamental sampling error and the techniques used to achieve a representative sample in the Fimiston Open Pit, Kalgoorlie.The utilisation of Pierre Gy's sampling theory has optimised the blast hole sample quality and quantity for submission to the assay laboratory. This has resulted in reduced cost and optimised assay reliability in statistical terms. Similarly the analysis of exploration drill holes for resource definition has optimised drilling procedures in terms of the drilling method, sample length and sample quantity.

Jan 1, 1993

By Musa MA

Tunnel excavation for sewer construction long remained a labour intensive, hazardous and costly operation. Even with the of mechanical and semi-mechanical shields for tunnel excavation, many problems remained until recently. In the past decade, however, the technology has changed dramatically which has made possible the use of advanced tunnelling methods for sewer construction.

Jan 1, 1993

By Xuanxue Mo, Zengqian Hou

"Abstract -Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcano­ genic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and back­ arc spreading during its evolution and formed a complete trench-arc-basin system, i.e., the Ganzi­ Litang suture zone, forearc basin, outer arc, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate fault­ bound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.Ali VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is two­fold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. Ali deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asyrnmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe_The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerais (Groups I and II) formed during intensifying stages of hydrothermal activity, and the majority of serni-yellow-ore minerals (Group III) formed during a thermal maximum . There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kuroko­ type VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By Gary Schaffer, Anthony Stentz

Surveying of mines is a necessary step in coal mining to assemble maps which are used for tracking progress in the development of the mine and to plan future coal removal. A first approach for automatically building high-resolution two-dimensioml maps of underground coal mines is presented. The technique assembles laser rangefinder scans obtained from several locations within the mine into a consistent global map of the mine. Each range scan comprises thousands of data points collected in one second, thereby achieving higher resolution and much faster measurement compared to a human using a transit. The raw data (range scans) are processed to fuse them into a consistent representation. This paper describes a first approach to automated surveying and presents initial results of merging range scans. Improvements to the scan-merging algorithm are proposed.

Jan 1, 1993